Search NASA⌕ Search

SEARCH · Search NASA

Results for “Snap Ring”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Tethering sockets and wrenches

The tethering of sockets and wrenches was accomplished to improve the safety of working over motor segments. To accomplish the tethering of the sockets to the ratchets, a special design was implemented in which a groove was machined into each socket. Each socket was then fitted with a snap ring that can spin around the machined groove. The snap ring is tethered to the handle of the ratchet. All open end wrenches are also tethered to the ratchet or to the operator, depending upon the type. Tests were run to ensure that the modified tools meet torque requirements. The design was subsequently approved by Space Safety.

Johnson, E. P.↗
NASA NTRS1980

Retaining a sleeve on a shaft

Snap ring with slotted tabs fits groove in shaft. Sleeve to be held on shaft fits over snap ring keeping it from expanding. Tabs are bent out to keep sleeve from slipping off shaft.

Pessin, R.↗
NASA NTRS1990

Method of balancing bladed gas turbine engine rotor

A balance ring (18) which is shrunk fit within each disk (12) of a rotor is selectively ground for detail balance. A plurality of openings (20) through the outer edge of the balance ring receive weights during the assembly balance of the rotor. A snap ring (42) retains the weights within the openings.

Novotny, Rudolph J.↗
NASA NTRS1989

Rotor balance system

A balance ring (18) which is shrunk fit within each disk (12) of a rotor is selectively ground for detail balance. A plurality of openings (20) through the outer edge of the balance ring receive weights during the asssembly balance of the rotor. A snap ring (42) retains the weights within the openings.

Novotny, Rudolph J.↗
NASA NTRS1966

Fastener provides for bolt misalignment and quick release of flange

Fastener enables two large flanges to be bolted together without close alignment between the bolt and bolt-hole diameters, and provides for a quick release of one of the flanges under emergency conditions. It contains a nut that is retained by a square head in a recess in one side of the removable flange and by a collar and snap ring on the other side of the flange.

England, C.↗
NASA NTRS1995

Metallographic Analysis of Brush Bristle and Integrity Testing of Brush Seal in Shroud Ring of T-700 Engine

Post-test investigation of a T-700 engine brush seal found regions void of bristles ('yanked out'), regions of bent-over bristles near the inlet, some 'snapped' bristles near the fence, and a more uniform 'smeared' bristle interface between the first and last axial rows of bristles. Several bristles were cut from the brush seal, wax mounted, polished, and analyzed. Metallographic analysis of the bristles near the rub tip showed tungsten-rich phases uniformly distributed throughout the bristle with no apparent change within 1 to 2 micron of the interface except for possibly a small amount of titanium, which would represent a transfer from the rotor. Analysis of the bristle wear face showed nonuniform tungsten, which is indicative of material resolidification. The cut end contained oxides and internal fractures; the worn end was covered with oxide scale. Material losses due to wear and elastoplastic deformation within the shear zone and third-body lubrication effects in the contact zone are discussed.

Hendricks, Robert C.↗
NASA NTRS1994

Some metallographic results for brush bristles and brush segments of a shroud ring brush seal tested in a T-700 engine

Post-test investigation of a T-700 engine brush seal found regions void of bristles ('yanked out'), regions of bent-over bristles near the inlet, some 'snapped' bristles near the fence, and a more uniform smeared bristle interface between the first and last axial rows of bristles. Several bristles and four brush segments were cut from the brush seal, wax mounted, polished, and analyzed. Metallographic analysis of the bristle near the rub tip showed tungsten-rich phases uniformly distributed throughout the bristle, no apparent change within 1 mu m of the interface, and possibly a small amount of titanium, which would represent a transfer from the rotor. Analysis of the bristle wear face showed nonuniform tungsten, which is indicative of material resolidification. The cut end contained oxides and internal fractures; the worn end was covered with oxide scale. Material losses due to wear and elastoplastic deformation within the shear zone and third-body lubrication effects in the contact zone are discussed.

Hendricks, Robert C.↗