Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stabilization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Enhancing the stability of copper chromite catalysts for the selective hydrogenation of furfural with ALD overcoating (II) – Comparison between TiO2 and Al2O3 overcoatings

TiO2 atomic layer deposition (ALD) overcoatings were applied to copper chromite catalysts to increase the stability for 2-furfuraldehyde (“furfural”) hydrogenation. After overcoating, about 75% activity was preserved compared to neat copper chromite: much higher activity than an alumina ALD overcoated catalyst with a similar number of ALD cycles. The effects of ALD TiO2 on the active Cu nanoparticles were studied extensively using both in-situ TPR/isothermal-oxidation and in-situ furfural hydrogenation via Cu XAFS. The redox properties of Cu were modified only slightly by the TiO2 ALD overcoat. However, a subtle electronic interaction was observed between the TiO2 ALD layers and the Cu nanoparticles. With calcination at 500 °C the interaction between the TiO2 overcoat and the underlying catalyst is strong enough to inhibit migration and site blocking by chromite, but is sufficiently weaker than the interaction between the Al2O3 overcoat and copper chromite that it does not strongly inhibit the catalytic activity of the copper nanoparticles.

Zhang, Hongbo↗

Glassy Carbon Substrate Oxidation Effects on Electrode Stability for Oxygen Evolution Reaction Catalysis Stability Benchmarking

Employing benchmarking metrics to capture the activity and stability of electrocatalysts for the oxygen evolution reaction (OER) in acid is a critical practice that enables meaningful comparison of catalyst material candidates reported throughout the literature. In this work, we find that ubiquitously used glassy carbon electrode substrates oxidize under typical OER operating conditions, forming a pacified, electrically insulating, and oxygen-rich surface layer that causes drastic loss of current density over the course of extended chronoamperometric stability tests at an anodic potential of 1.7 VRHE. We show that the experimentally observed stability of glassy carbon-based electrodes is approximately two orders of magnitude lower than that expected solely from dissolution-based catalyst intrinsic stability of Ir-based catalysts. We additionally find that glassy carbon-based electrode stability measured by chronoamperometric holds is greatly impacted by catalyst loading, with high catalyst loadings improving the stability of the overall electrode via a protective effect on the glassy carbon substrate. Altogether, our investigation highlights that glassy carbon is not electrochemically inert under OER conditions on the timescale of common stability tests, which can cause electrodes to exhibit performance losses that do not reflect the intrinsic stability of the actual catalyst material being investigated. In light of our findings, we underscore the usefulness of metrics, such as the S-number, to reflect intrinsic catalyst material stability.

25 ENERGY STORAGE↗

Origins of Acid-Gas Stability Behavior in Zeolitic Imidazolate Frameworks: The Unique High Stability of ZIF-71

Zeolitic imidazolate frameworks (ZIFs) are promising materials for industrial process separations, but recent literature reports have highlighted their vulnerability to acid gases (e.g., SO 2 , CO 2 , NO 2 , H 2 S), often present in practical applications. While previous work has documented the widely varying stability behavior of many ZIFs under varying (humid and dry) acid gas environments, efforts to explain or correlate these experimental observations via empirical descriptors have not succeeded. A key observation is that ZIF-71 (RHO topology) is an extraordinarily stable ZIF material, retaining both structure and porosity under prolonged humid SO 2 exposure whereas many other well-known ZIFs with different linkers and topologies (such as ZIF-8) were shown to degrade. Through a combination of hybrid quantum mechanics/molecular mechanics (QM/MM) based methods and statistical mechanical models, we successfully explain this important experimental observation via atomistic investigations of the reaction mechanism. Our holistic approach reveals an ~9 times lower average defect formation rate in ZIF-71 RHO compared to ZIF-8 SOD, leading to the conclusion that the observed experimental stability of this material rises from kinetic effects. Moreover, our analysis reveals that differing stability of the two materials is determined by the distributions of acid gas molecules, which is difficult to capture using empirical descriptors. Furthermore, our results suggest wider applicability of the present approach, toward identifying tuned functional groups and topologies that move the acid gas distributions away from more reactive sites and thus allow enhanced kinetic stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Distortions and stabilization of simple-cubic calcium at high pressure and low temperature

Ca-III, the first superconducting calcium phase under pressure, was identified as simple-cubic (sc) by previous X-ray diffraction (XRD) experiments. In contrast, all previous theoretical calculations showed that sc had a higher enthalpy than many proposed structures and had an imaginary (unstable) phonon branch. By using our newly developed submicrometer high-pressure single-crystal XRD, cryogenic high-pressure XRD, and theoretical calculations, we demonstrate that Ca-III is neither exactly sc nor any of the lower-enthalpy phases, but sustains the sc-like, primitive unit by a rhombohedral distortion at 300 K and a monoclinic distortion below 30 K. This surprising discovery reveals a scenario that the high-pressure structure of calcium does not go to the zero-temperature global enthalpy minimum but is dictated by high-temperature anharmonicity and low-temperature metastability fine-tuned with phonon stability at the local minimum.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Phase stability in thermally-aged CASS CF8 under heavy ion irradiation

The stability of the microstructure of a cast austenitic stainless steel (CASS), before and after heavy ion irradiation, was investigated by atom probe tomography (APT). A CF8 ferrite–austenite duplex alloy was thermally aged at 400 °C for 10,000 h. After this treatment, APT revealed nanometer-sized G-phase precipitates and Fe-rich α and Cr-enriched α' phase separated regions in the ferrite. The thermally-aged CF8 specimen was irradiated with 1 MeV Kr ions to a fluence of 1.88 × 10 19 ions/m 2 at 400 °C. After irradiation, APT analysis revealed a strong spatial/dose dependence of the G-phase precipitates and the α–α' spinodal decomposition in the ferrite. For the G-phase precipitates, the number density increased and the mean size decreased with increasing dose, and the particle size distribution changed considerably under irradiation. The inverse coarsening process can be described by recoil resolution. The amplitude of the α–α' spinodal decomposition in the ferrite was apparently reduced after heavy ion irradiation.

Li, Meimei↗

Cubic phase stability, optical and magnetic properties of Cu-stabilized zirconia nanocrystals

By means of experimental and ab initio investigations, in this article we report on the cubic phase stability of Cu doped zirconia (ZrO 2 ) at room temperature, and further characterize its structural, optical and magnetic properties. Various compositions of Zr 1– x Cu x O 2 (0.01 ≤ x ≤ 0.25) nanocrystallites of average size ~16 nm were synthesized using co-precipitation technique. Thermal analysis and kinetics of crystallization revealed that the cubic phase at ambient temperature can be stabilized by using a critical calcination temperature of 500 °C for 8 h in air and a critical composition of $x_c$ = 0.10 ± 0.05. For $x < x_c$, some undigested monoclinic phase of ZrO 2 exists together with the cubic structure. However, for $x > x_c$, the monoclinic CuO emerges as a secondary phase with shrinkage of unit-cell volume with increasing the Cu content. At x = 0.05 and 500 °C calcination temperature, we observe a high degree of cubic crystallinity which breaks down into monoclinic phase with increasing calcination temperature beyond 550 °C. Electron magnetic resonance studies provide evidence for the substitution of Cu 2+ ( 2 D 5/9 ,3d 9 ) ions at Zr 4+ sites with g ∥ = 2.250, g ⊥ = 2.018 and average g a = (g ∥ + 2g ⊥ )/3 ~ 2.1. The temperature dependence of magnetic susceptibility measurements from 2 K to 300 K exhibits Curie–Weiss behaviour whose analysis using g a = 2.1 and spin S = 1/2 yields x = 0.028 and x = 0.068 for the nominal x = 0.05 and x = 0.20 samples, respectively. This magnetic analysis confirms the findings from x-ray diffraction that only a part of Cu is successfully doped into cubic phase of Cu-doped ZrO 2 . The optical bandgap decreases with increasing x, which is due to the emergence of Cu-d states at Fermi-level near the valence bands, thus making Cu-doped zirconia a hole doped (p-type) semiconductor.

electron spin resonance↗

Structure and thermodynamic stability of UTa 3 O 10 , a U( v )-bearing compound

Heating a mixture of uranyl(VI) nitrate and tantalum(V) oxide in the molar ratio of 2 : 3 to 1400 °C resulted in the formation of a new compound, UTa 3 O 10 . The honey colored to yellow brown crystals of UTa 3 O 10 crystallize in an orthorhombic structure with the space group Fddd (no. 70), lattice parameters a = 7.3947(1), b = 12.7599(2), c = 15.8156(2) Å, and Z = 8. Vertex sharing [TaO 6 ] 7- octahedra of two crystallographically distinct Ta cations form a three dimensional tantalate framework. Within this framework, six membered rings of [TaO 6 ] 7- octahedra are formed within the (001) plane. The center of these rings is occupied by the uranyl cations [UO 2 ] + , with an oxidation state of +5 for uranium. The pentavalence of U and Ta was confirmed by X-ray photoelectron spectroscopy and X-ray adsorption spectroscopy. The enthalpy of formation of UTa 3 O 10 from Ta 2 O 5 , β-U 3 O 7 , and U 3 O 8 has been determined to be 13.1 ± 18.1 kJ mol -1 using high temperature oxide melt solution calorimetry with sodium molybdate as the solvent at 700 °C. The close to zero enthalpy of formation of UTa 3 O 10 can be explained by closely balanced structural stabilizing and destabilizing factors, which may also apply to other UM 3 O 10 compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Origin of Nanoscale Phase Stability Reversals in Titanium Oxide Polymorphs

We have monitored the hydrothermal crystallization of titania nanoparticles by in situ X-ray diffraction (XRD). Using the refined average structures from the XRD measurements, we calculated potential energy variations with particle size on periodic bulk structures using density functional theory (DFT). These variations cannot account for the enthalpy required to stabilize anatase relative to rutile. Thus, the hypothesis that the strain of the surface structure of nanoparticles accounts for the stabilization of anatase is not applicable to the growth of titania in water. DFT calculations on model nanoparticles do generate lower surface energies for anatase than for rutile that are large enough to explain the stability reversal in nanoparticles relative to the bulk phase. Rather than arising from two-dimensional surface structure alone, as previously thought, the total surface energies are critically dependent upon defects associated with edges and corners of nanocrystals at particle sizes ?3 nm (i.e., during the nucleation process). As the particles grow, the bulk free energy becomes relatively more important, causing rutile to become stable at larger particle sizes. This study quantifies for the first time the critical role of edge and vertex energies in determining the relative phase stabilities of TiO2 nanoparticles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of Imide–Orthoborate Dual-Salt Mixtures in Organic Carbonate Electrolytes on the Stability of Lithium Metal Batteries

The effects of lithium imide and lithium orthoborate dual-salt electrolytes of different salt chemistries in carbonate solvents on the cycling stability of Li metal batteries were systematically and comparatively investigated. Two imide salts (LiTFSI and LiFSI) and two orthoborate salts (LiBOB and LiDFOB) were chosen for this study and compared with the conventional LiPF6 salt. The cycling stability of the Li metal cells with the electrolytes follows the order from good to poor as LiTFSI-LiBOB > LiTFSI-LiDFOB > LiPF6 > LiFSI-LiBOB > LiFSI-LiDFOB, indicating that LiTFSI behaves better than LiFSI and LiBOB over LiDFOB in these four dual-salt mixtures. The LiTFSI-LiBOB can effectively protect the Al substrate and form a more robust surface film on Li metal anode, while the LiFSI-LiBOB results in serious corrosion to the stainless steel cell case and a thicker and looser surface film on Li anode. Computational calculations indicate that the chemical and electrochemical stabilities also follow the order of LiTFSI-LiBOB > LiTFSI-LiDFOB > LiFSI-LiBOB > LiFSI-LiDFOB. The key findings of this work emphasize that the salt chemistry is critically important for enhancing the interfacial stability of Li metal anode and should be carefully manipulated in the development of high performance Li metal batteries.

Li metal batteries, dual-salt electrolyte, solid e↗

Grain growth and phase stability of nanocrystalline cubic zirconia under ion irradiation

Grain growth, oxygen stoichiometry and phase stability of nanostructurally-stabilized zirconia (NSZ) in pure cubic phase are investigated under 2 MeV Au ion bombardment at 160 and 400 K to doses up to 35 displacements per atom (dpa). The NSZ films are produced by ion-beam-assisted deposition technique at room temperature with an average grain size of 7.7 nm. The grain size increases with dose, and follows a power law (n=6) to a saturation value of ~30 nm that decreases with temperature. Slower grain growth is observed under 400 K irradiations, as compared to 160 K irradiations, indicating that thermal grain growth is not activated and defect-stimulated grain growth is the dominating mechanism. While cubic phase is perfectly retained and no new phases are identified after the high-dose irradiations, reduction of oxygen in the irradiated NSZ films is detected. The ratio of O to Zr decreases from ~2.0 for the as-deposited films to ~1.65 after irradiation to ~35 dpa. Significant increase of oxygen vacancies in nanocrystalline zirconia suggests substantially enhanced oxygen diffusion under ion irradiation, a materials behavior far from equilibrium. The oxygen deficiency may be essential in stabilizing cubic phase to larger grain sizes.

Environmental Molecular Sciences Laboratory↗