Search NASA⌕ Search

SEARCH · Search NASA

Results for “Static Aeroelastic Stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

An analysis of the effects of aeroelasticity on static longitudinal stability and control of a swept-wing airplane

A theoretical analysis has been made of the effects of aeroelasticity on the static longitudinal stability and elevator angle required for balance of an airplane. The analysis is based on the familiar stability equation expressing the contribution of wing and tail to longitudinal stability. Effects of wing, tail, and fuselage flexibility are considered. Calculated effects are shown for a swept-wing bomber of relatively high flexibility.

Skoog, Richard B↗
NASA NTRS2011

A Quasi-Steady Flexible Launch Vehicle Stability Analysis Using Steady CFD with Unsteady Aerodynamic Enhancement

Launch vehicles frequently experience a reduced stability margin through the transonic Mach number range. This reduced stability margin is caused by an undamping of the aerodynamics in one of the lower frequency flexible or rigid body modes. Analysis of the behavior of a flexible vehicle is routinely performed with quasi-steady aerodynamic lineloads derived from steady rigid computational fluid dynamics (CFD). However, a quasi-steady aeroelastic stability analysis can be unconservative at the critical Mach numbers where experiment or unsteady computational aeroelastic (CAE) analysis show a reduced or even negative aerodynamic damping. This paper will present a method of enhancing the quasi-steady aeroelastic stability analysis of a launch vehicle with unsteady aerodynamics. The enhanced formulation uses unsteady CFD to compute the response of selected lower frequency modes. The response is contained in a time history of the vehicle lineloads. A proper orthogonal decomposition of the unsteady aerodynamic lineload response is used to reduce the scale of data volume and system identification is used to derive the aerodynamic stiffness, damping and mass matrices. The results of the enhanced quasi-static aeroelastic stability analysis are compared with the damping and frequency computed from unsteady CAE analysis and from a quasi-steady analysis. The results show that incorporating unsteady aerodynamics in this way brings the enhanced quasi-steady aeroelastic stability analysis into close agreement with the unsteady CAE analysis.

Bartels, Robert E.↗
NASA NTRS1951

An analysis of the effects of aeroelasticity on static longitudinal stability and control of a swept-back-wing airplane

A theoretical analysis of the effects of aeroelasticity on the stick-fixed static longitudinal stability and elevator angle required for balance of an airplane is presented together with calculated effects for a swept-wing bomber of relatively high flexibility. Although large changes in stability due to certain parameters are indicated for the example airplane, the over-all stability change after considering all parameters was quite small, compared to the individual effects, due to the counterbalancing of wing and tail contributions. The effect of flexibility on longitudinal control for the example airplane was found to be of little real importance.

STABILITY, LONGITUDINAL - STATIC↗
NASA NTRS1976

An investigation of aeroelastic phenomena associated with an oblique winged aircraft

Oblique wing aeroelasticity studies are reviewed. The static aeroelastic stability characteristics of oblique wing aircraft, lateral trim requirements for 1-g flight, and the dynamic aeroelastic stability behavior of oblique winged aircraft, primarily flutter, are among the topics studied. The similarities and differences between oblique winged aircraft and conventional, bilaterally symmetric, swept wing aircraft are emphasized.

Weisshaar, T. A.↗
NASA NTRS2023

Fully Coupled Aeroelastic Stability Analysis of Adaptive Shape Memory Alloy Structural Technologies for Airframe Noise Reduction

This final report documents work performed by ATA Engineering, Inc., (ATA) to develop computational models and analyze the coupled fluid-structure response of two types of noise treatments applied to the leading-edge-slat component of a high-lift system typical of modern transport aircraft. The first treatment is a slat-gap filler (SGF), which closes the gap between the suction surfaces of a deployed slat and an aircraft main wing, and the second treatment is a slat-cove filler (SCF), which replaces the recirculating flow on the slat cove with a surface that promotes flow attachment. The representative airframe chosen for this work was NASA’s High-Lift Common Research Model (CRM-HL) in a baseline high-lift configuration. Superelastic shape memory alloys (SMAs) have been identified as enabling materials for these structural treatments. Since the technology elements rely upon having a highly reconfigurable structure, designs were assessed for their static aeroelastic deflection as well as their dynamic aeroelastic stability using coupled computational fluid dynamics (CFD) and nonlinear computational structural dynamics (NL-CSD) tools. Specifically, fluid-structure interaction (FSI) problems were solved computationally using the CFD solver Loci/CHEM and the NL-CSD solver Abaqus. As a part of the overall project, a similar capability was implemented using the CFD solver FUN3D coupled to Abaqus, although that work is documented in a separate report and that FSI framework was not used to analyze any of NASA’s SGF and SCF configurations. The technical approach consisted of solving for the flow field around the entire vehicle using a global CFD model, followed by extraction of relevant local subdomain data for CFD and NL-CSD co-simulations. The SGF design was analyzed using both 2D and 3D co-simulations to predict quasi-static aeroelastic deformations and to assess dynamic aeroelastic stability, whereas the SCF was analyzed in 2D only. SGF static aeroelastic response predictions focused on characterizing the deformed shape, with maximum displacements predicted to be on the order of magnitude of the technology element panel thickness. SGF dynamic aeroelastic response predictions used Partial Floquet analysis of the temporal evolution of selected nodal displacements to quantify the sign and magnitude of aeroelastic damping. Results suggest that the CRM-HL operating conditions would result in a dynamically stable response. The simulated dynamic pressure was also increased up to a factor of about four, and resulting responses suggest that predicted dynamic stability would be achieved with some margin.

Fluid Structure Interaction↗
NASA NTRS1983

The effect of a normal shock on the aeroelastic stability of a panel

The effect of a standing shock wave on the static and dynamic aeroelastic stability of a flexible panel is investigated using a linear structural and aerodynamic theoretical model. It is found that the shock is generally stabilizing. The lowest critical dynamic pressures are associated with shock positions downstream from the panel, where the panel is uninfluenced by the shock.

Williams, M. H.↗
NASA NTRS1996

On longitudinal control of high speed aircraft in the presence of aeroelastic modes

Longitudinal control system design is considered for a linearized dynamic model of a supersonic transport aircraft concept characterized by relaxed static stability and significant aeroelastic interactions. Two LQG-type controllers are designed using the frequency-domain additive uncertainty formulation to ensure robustness to unmodeled flexible modes. The first controller is based on a 4th-order model containing only the rigid-body modes, while the second controller is based on an 8th-order model that additionally includes the two most prominent flexible modes. The performance obtainable from the 4th-order controller is not adequate, while the 8th-order controller is found to provide better performance. Frequency-domain and time-domain (Lyapunov) methods are subsequently used to assess the robustness of the 8th-order controller to parametric uncertainties in the design model.

Joshi, Suresh M.↗
NASA NTRS2014

Aeroelastic Tailoring of a Plate Wing with Functionally Graded Materials

This work explores the use of functionally graded materials for the aeroelastic tailoring of a metallic cantilevered plate-like wing. Pareto trade-off curves between dynamic stability (flutter) and static aeroelastic stresses are obtained for a variety of grading strategies. A key comparison is between the effectiveness of material grading, geometric grading (i.e., plate thickness variations), and using both simultaneously. The introduction of material grading does, in some cases, improve the aeroelastic performance. This improvement, and the physical mechanism upon which it is based, depends on numerous factors: the two sets of metallic material parameters used for grading, the sweep of the plate, the aspect ratio of the plate, and whether the material is graded continuously or discretely.

Dunning, Peter D.↗
NASA NTRS1977

Effect of chordwise forces and deformations and deformations due to steady lift on wing flutter

This investigation explores the effects of chordwise forces and deformations and steady-state deformation due to lift on the static and dynamic aeroelastic stability of a uniform cantilever wing. Results of this analysis are believed to have practical applications for high-performance sailplanes and certain RPV's. The airfoil cross section is assumed to be symmetric and camber bending is neglected. Motions in vertical bending, fore-and-aft bending, and torsion are considered. A differential equation model is developed, which included the nonlinear elastic bending-torsion coupling that accompanies even moderate deflections. A linearized expansion in small time-dependent deflections is made about a steady flight condition. The stability determinant of the linearized system then contains coefficients that depend on steady displacements. Loads derived from two-dimensional incompressible aerodynamic theory are used to obtain the majority of the results, but cases using three-dimensional subsonic compressible theory are also studied. The stability analysis is carried out in terms of the dynamically uncoupled natural modes of vibration of the uniform cantilever.

Boyd, W. N.↗
NASA NTRSDate not supplied

Fully Coupled Aeroelastic Stability Analysis of Adaptive Shape Memory Alloy Structural Technologies for Airframe Noise Reduction

The objective of this work is the development of computational models and analysis of the coupled fluid-structure response of a slat gap filler (SGF) noise treatment applied to the leading-edge-slat component of a high-lift system typical of modern transport aircraft. The representative airframe chosen for this work is NASA’s High-lift Common Research Model (CRM-HL) in a baseline high-lift configuration. Superelastic shape memory alloys (SMAs) have been identified as enabling materials for these structural treatments. Since the technology elements rely upon having a highly reconfigurable structure, designs must be assessed for static aeroelastic deflection as well as dynamic aeroelastic stability using coupled computational fluid dynamics (CFD) and nonlinear computational structural dynamics (NL CSD) tools. The technical approach consists of solving for the flow field around the entire vehicle using a global CFD model, followed by extraction of relevant local subdomain data for CFD and NL-CSD co-simulations. The SGF design is assessed using both 2D and 3D co-simulations to predict quasi-static aeroelastic deformations and to assess dynamic aeroelastic stability.

Fluid structure interaction↗
NASA NTRS1983

Approach to establishing the effect of aeroelasticity on aerodynamic characteristics of the space shuttle orbiter

The static aeroelastic effects on the longitudinal stability and elevon/aileron effectiveness of the space transportation system (STS) Space Shuttle orbiter were estimated by a simplified approach called the elevon torsional stiffness (ETS) method. This method employs rigid model wind tunnel test results to predict aeroelastic effects. Lateral/directional stability and rudder effectiveness were based on results of a wind tunnel test in which a flexible tail model was used. Comparisons with selective flight data are made in this paper. Results of correlations with flight data (although limited at the present time) verify the predicted aeroelastic effects for the orbiter. The orbiter's structural characteristics are such that the effects of aeroelasticity, whether estimated using analytical techniques or simplified methods, do not appear to affect the vehicle performance to any great extent. The large amount of scatter in the flight-extracted data made verification of the aeroelastic corrections very difficult. Generally, the simplified elevon torsional stiffness method provided better correlation with flight test results than he analytical method and reduced the verification effort and cost.

Schlosser, D. C.↗
NASA NTRS1984

Body-freedom flutter of a 1/2-scale forward-swept-wing model, an experimental and analytical study

The aeroelastic phenomenon known as body-freedom flutter (BFF), a dynamic instability involving aircraft-pitch and wing-bending motions which, though rarely experienced on conventional vehicles, is characteristic of forward swept wing (FSW) aircraft was investigated. Testing was conducted in the Langley transonic dynamics tunnel on a flying, cable-mounted, 1/2-scale model of a FSW configuration with and without relaxed static stability (RSS). The BFF instability boundaries were found to occur at significantly lower airspeeds than those associated with aeroelastic wing divergence on the same model. For those cases with RSS, a canard-based stability augmentation system (SAS) was incorporated in the model. This SAS was designed using aerodynamic data measured during a preliminary tunnel test in which the model was attached to a force balance. Data from the subsequent flutter test indicated that BFF speed was not dependent on open-loop static margin but, rather, on the equivalent closed-loop dynamics provided by the SAS. Servo-aeroelastic stability analyses of the flying model were performed using a computer code known as SEAL and predicted the onset of BFF reasonably well.

Chipman, R.↗
NASA NTRS2015

Level-Set Topology Optimization with Aeroelastic Constraints

Level-set topology optimization is used to design a wing considering skin buckling under static aeroelastic trim loading, as well as dynamic aeroelastic stability (flutter). The level-set function is defined over the entire 3D volume of a transport aircraft wing box. Therefore, the approach is not limited by any predefined structure and can explore novel configurations. The Sequential Linear Programming (SLP) level-set method is used to solve the constrained optimization problems. The proposed method is demonstrated using three problems with mass, linear buckling and flutter objective and/or constraints. A constraint aggregation method is used to handle multiple buckling constraints in the wing skins. A continuous flutter constraint formulation is used to handle difficulties arising from discontinuities in the design space caused by a switching of the critical flutter mode.

Dunning, Peter D.↗
NASA NTRS1986

Wright Brothers Lectureship in Aeronautics: Experience with HiMAT remotely piloted research vehicle - An alternate flight test approach

The highly maneuverable aircraft technology (HiMAT) program explored the various and complex interactions of advanced technologies, such as aeroelastic tailoring, close-coupled canard, and relaxed static stability. A 0.44-subscale remotely piloted research vehicle (RPRV) of a hypothetical fighter airplane was designed and flight-tested to determine the effects of these interactions and to define the design techniques appropriate for advanced fighter technologies. Flexibility and high maneuverability were provided by flight control laws implemented in ground-based computers and telemetered to the vehicle control system during flight tests. The high quality of the flight-measured data and their close correlation with the analytical design modeling proved that the RPRV is a viable and cost-effective tool for developing aerodynamic, structure, and control law requirements for highly maneuverable fighter airplanes of the future.

Deets, D. A.↗
NASA NTRS2005

Experimental Results from the Active Aeroelastic Wing Wind Tunnel Test Program

The Active Aeroelastic Wing (AAW) program is a cooperative effort among NASA, the Air Force Research Laboratory and the Boeing Company, encompassing flight testing, wind tunnel testing and analyses. The objective of the AAW program is to investigate the improvements that can be realized by exploiting aeroelastic characteristics, rather than viewing them as a detriment to vehicle performance and stability. To meet this objective, a wind tunnel model was crafted to duplicate the static aeroelastic behavior of the AAW flight vehicle. The model was tested in the NASA Langley Transonic Dynamics Tunnel in July and August 2004. The wind tunnel investigation served the program goal in three ways. First, the wind tunnel provided a benchmark for comparison with the flight vehicle and various levels of theoretical analyses. Second, it provided detailed insight highlighting the effects of individual parameters upon the aeroelastic response of the AAW vehicle. This parameter identification can then be used for future aeroelastic vehicle design guidance. Third, it provided data to validate scaling laws and their applicability with respect to statically scaled aeroelastic models.

Heeg, Jennifer↗
NASA NTRS2010

Computational Aeroelastic Analysis of the Ares Launch Vehicle During Ascent

This paper presents the static and dynamic computational aeroelastic (CAE) analyses of the Ares crew launch vehicle (CLV) during atmospheric ascent. The influence of launch vehicle flexibility on the static aerodynamic loading and integrated aerodynamic force and moment coefficients is discussed. The ultimate purpose of this analysis is to assess the aeroelastic stability of the launch vehicle along the ascent trajectory. A comparison of analysis results for several versions of the Ares CLV will be made. Flexible static and dynamic analyses based on rigid computational fluid dynamic (CFD) data are compared with a fully coupled aeroelastic time marching CFD analysis of the launch vehicle.

Bartels, Robert E.↗