SEARCH · Search NASA

Results for “Stepover”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

6 records

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Rupture Jumping and Seismic Complexity in Models of Earthquake Cycles for Fault Stepovers with Off-Fault Plasticity

ABSTRACT Fault stepovers are prime examples of geometric complexity in natural fault zones that may affect seismic hazard by determining whether an earthquake rupture continues propagating or abruptly stops. However, the long-term pattern of seismicity near-fault stepovers and underlying mechanisms of rupture jumping in the context of earthquake cycles are rarely studied. Leveraging a hybrid numerical scheme combining the finite element and the spectral boundary integral methods, FEBE, we carry out fully dynamic simulations of sequences of earthquakes and aseismic slip for both compressive and tensile stepovers with off-fault plasticity. We consider a rate-and-state friction law for the fault friction and pressure-sensitive Drucker–Prager plasticity for the off-fault bulk response. We observe that the accumulation of plastic deformation, an indication of off-fault damage, is significantly different in the two cases, with more plastic deformation projected in the overlapping region for the tensile stepover. The seismic pattern for a tensile stepover is more complex than for a compressive stepover, and incorporating plasticity also increases complexity, relative to the elastic case. A tensile stepover with off-fault plasticity shows rupture segmentation, temporal clustering, and frequent rupture jumping from one fault to another. These results shed light on possible mechanisms of rupture jumping in fault stepovers as well as the long-term evolution of the fault zone.

Geochemistry & Geophysics↗

DOE OSTI2023

Correcting distortions of thin-walled machined parts by machine hammer peening

Thin-walled aerostructural components frequently get distorted after the machining process. Reworking to correct distortions or eventually rejecting parts significantly increases the cost. This paper proposes a new approach to correct distortions in thin-walled components by strategically applying hammer peening on target surfaces of a machined component. Aluminium alloy 7475-T7351 was chosen for this research. The study was divided in two stages. First, the residual stresses (RS) induced by four different pneumatic hammer peening conditions (modifying the stepover distance and initial offset) were characterised in a test coupon, and one of the conditions was selected for the next stage. In the second stage, a FEM model was used to predict distortions caused by machining in a representative workpiece. Then, the RS induced by hammer peening were included in an FEM model to define two hammer peening strategies (varying the coverage area) to analyse the capability to reduce distortions. Two workpieces were machined and then treated with the simulated hammer peening strategies for experimental validation. Results in the test coupon showed that pneumatic hammer peening can generate high compressive RS (-50 to –350 MPa) up to 800 μm depth, with their magnitude increasing with a reduced stepover distance. Application of hammer peening over 4% of the surface of the representative workpiece reduced the machining-induced distortions by 37%, and a coverage area of 100% led to and overcorrection by a factor of five. This confirms that hammer peening can be strategically applied (in target areas and changing the percentage of coverage) to correct low or severe distortions.

42 ENGINEERING↗

DOE OSTI2022

Property-structure-process relationships in dissimilar material repair with directed energy deposition: Repairing gray cast iron using stainless steel 316L

Directed energy deposition (DED) based remanufacturing leverages the flexibility of additive manufacturing to add value to broken or worn components. DED offers the ability to repair cast iron, a material difficult to repair with traditional welding techniques. Despite this, development of appropriate DED process conditions for bimetallic cast iron structures lags low- and medium-carbon steel repair. Thermal stresses and porosity generated by high-temperature deposition on cast iron often lower mechanical properties and hinder the qualification process. In this report scanning speed, powder mass flow rate, and stepover width are studied in multiple-track structures deposited on gray cast iron. Dilution and residual stresses are found to be highly dependent on the selected process parameters. Samples with a higher volumetric energy input, e.g., slower scanning speeds and higher powder feed rates, showed improved density and lower residual stresses but suffered lower dilution into the substrate. The presented conditions further the development of additive manufacturing technologies for automotive repair.

42 ENGINEERING↗

DOE OSTI2020

Analysis of Fault Zone Resonance Modes Recorded by a Dense Seismic Array Across the San Jacinto Fault Zone at Blackburn Saddle

We present observations and modeling of spatial eigen-functions of resonating waves within fault zone waveguide, using data recorded on a dense seismic array across the San Jacinto Fault Zone (SJFZ) in southern California. The array consists of 5-Hz geophones that cross the SJFZ with ~10-30 m spacing at the Blackburn Saddle near the Hemet Stepover. Wavefield snapshots after the S wave arrival are consistent for more than 50 near-fault events, suggesting that this pattern is controlled by the fault zone structure rather than source properties. Data from example event with high signal to noise ratio shows three main frequency peaks at ~1.3 Hz, ~2.0 Hz, and ~2.8 Hz in the amplitude spectra of resonance waves averaged over stations near the fault. The data are modeled with analytical expressions for eigen-functions of resonance waves in a low-velocity layer (fault zone) between two quarter-spaces. Using a grid search-based method, we investigate the possible width of the waveguide, location within the array, and shear wave velocities of the media that fit well the resonance signal at ~1.3 Hz. The results indicate a ~300 m wide damaged fault zone layer with ~65% S wave velocity reduction compared to the host rock. The SW edge of the low-velocity zone is near the mapped fault surface trace, indicating that the damage zone is asymmetrically located at the regionally faster NE crustal block. The imaging resolution of the fault zone structure can be improved by modeling fault zone resonance modes and trapped waves together.

58 GEOSCIENCES↗

DOE OSTI2024

Impact of Heat Input and Step Over Distance on Part Geometry for Multi-Bead WAAM Components

Abstract This study investigates the impact of heat input and overlap ratio or stepover distance on part geometry in wire arc additive manufacturing (WAAM). In this work, an experimental approach was taken to quantify the variation in height and aspect ratio of walls at different combinations of overlap and heat input. Multi-bead walls were deposited with the overlap ratio varying from ½, ⅔, and 1 at a low, medium, and high-power set point on the welding power supply. A relationship between heat input, overlap ratio, and the resultant part geometry is established. Trials with an overlap ratio of one and low to medium heat input exhibited greater lack of fusion defects than the high heat input trials. At higher heat input levels, the as-deposited geometry was found to have less variation in height and an increase in aspect ratio compared to lower heat input trials. The aspect ratio of deposited walls ranged from approximately 1, for the low-power trial with an overlap ratio of ½, to approximately 7, for the high-power trial with an overlap ratio of 1. Additionally, the low and medium power trials with an overlap ratio of ⅔ exhibited the least height variation in the top surface for those heat input levels with an average range of 2.9 mm and 1.8 mm respectively. For the high heat input trials, an overlap ratio of 1 was observed to have the least variation in height with a standard deviation of 0.42 mm and an average range of 1.7 mm; however, lack of fusion defects were present in the top surface and the part cross section.

Hussein, Zaky↗

DOE OSTI2021

Potential structures - Applications of Machine Learning Techniques to Geothermal Play Fairway Analysis in the Great Basin Region, Nevada

This submission contains shapefiles, geotiffs, and symbology for the revised-from-Play-Fairway potential structures/structural settings used in the Nevada Geothermal Machine Learning project. Layers include potential structural setting ellipses, centroids, and distance-to-centroid raster. A submission linking the full GitHub repository for our machine learning Jupyter Notebooks will appear in the related datasets section of this page once available.

15 GEOTHERMAL ENERGY↗