Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stress Gradients”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Method for controlling stress gradients in PVD aluminum nitride

In this study we describe a method for controlling both the residual stress and the through-thickness stress gradient of aluminum nitride (AlN) thin films using a multi-step deposition process that varies the applied radio frequency (RF) substrate bias. The relationship between the applied RF substrate bias and the AlN residual stress is characterized using AlN films grown on oxidized silicon substrates is determined using 100 nm–1.5 μm thick blanket AlN films that are deposited with 60–100 W applied RF biases; the stress-bias relationship is found to be well described using a power law relationship. Using this relationship, we develop a model for varying the RF bias in a series of discrete deposition steps such that each deposition step has zero average stress. The applied RF bias power in these steps is tailored to produce AlN films that have minimized both the residual stress and the film stress gradient. AlN cantilevers were patterned from films deposited using this technique, which show reduced curvature compared to those deposited using a single RF bias setting, indicating a reduction of the stress gradient in the films.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Accelerated creep profiling: a high-throughput thermal- and stress-gradient approach applied to additive and wrought stainless steel

Here, this study investigates logarithmic creep behavior at temperatures near room temperature in wrought and additively manufactured (AM) 316 L austenitic stainless steel. A novel high-throughput (HiTp) methodology employed thermal gradients to obtain stress- and temperature-dependence of creep behavior. The findings, based on 104 two-week creep tests, reveal significant differences in creep response between wrought and AM materials. Compared to the wrought material, the AM material exhibited a higher activation energy and a lower activation volume. These differences were attributed to the materials’ distinct microstructural features, e.g., dislocation cell structures and precipitate distributions, which alter the susceptibility to dislocation glide creep, particularly at stresses below the yield stress. The HiTp methodology provides both an accelerated determination of low-temperature creep mechanisms, offering critical data for the design and optimization of alloys in near-ambient, high stress applications.

316 L Stainless steel↗
DOE OSTI2018

Investigation of the Effect of Residual Stress Gradient on the Wear Behavior of PVD Thin Films

The control of residual stresses has been seldom investigated in multilayer coatings dedicated to improvement of wear behavior. Here, we report the preparation and characterization of superposed structures composed of Cr, CrN and CrAlN layers. Nano-multilayers CrN/CrAlN and Cr/CrN/CrAlN were deposited by Physical Vapor Deposition (PVD) onto Si (100) and AISI4140 steel substrates. The Cr, CrN and CrAlN monolayers were developed with an innovative approach in PVD coatings technologies corresponding to deposition with different residual stresses levels. Composition and wear tracks morphologies of the coatings were characterized by scanning electron microscopy, high-resolution transmission electron microscopy, atomic force microscopy, x-ray photoelectron spectroscopy, energy-dispersive x-ray spectroscopy, x-ray diffraction and 3D-surface analyzer. The mechanical properties (hardness, residual stresses and wear) were investigated by nanoindentation, interferometry and micro-tribometry (fretting-wear tests). Observations suggest that multilayer coatings are composed mostly of nanocrystalline. The residual stresses level in the films has practically affected all the physicochemical and mechanical properties as well as the wear behavior. Consequently, it is demonstrated that the coating containing moderate stresses has a better wear behavior compared to the coating developed with higher residual stresses. The friction contact between coated samples and alumina balls shows also a large variety of wear mechanisms. In particular, the abrasive wear of the coatings was a combination of plastic deformation, fine microcracking and microspallation. The application of these multilayers will be wood machining of green wood.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Molecular dynamics of the early stages of high-temperature corrosion

In this work, we performed molecular dynamics simulations of the high-temperature oxidation of metal alloys composed of Al, Cr, and Fe and compared their behavior with that of pure Fe. The metal alloy elements (Al and Cr) segregated to the surface during oxidation, producing a lower stress gradient at the metal/environment interface compared to pure Fe. We have found that the lowered stress gradients produced in the alloy material appear to play a key role in the development of corrosion. Interfaces with lower stress gradients have reduced rates of H 2 O adsorption, especially for the ferritic (bcc) alloys. The diffusivity of oxygen and hydrogen drops more rapidly for the interfaces with reduced stress gradients. The stress gradient is also diminished when the gas pressure is increased, indicating that the Fe-Cr-Al alloy system is more resistant to oxidation than pure Fe at higher pressures. Therefore, we conclude that the lower stress gradients at the alloy/environment interface reduce the stress concentration and can slow down the rate of the initial oxide scale growth. We also compared bcc and fcc alloys with pure Fe based on our three evaluation criteria (peak stress, stress gradient, and summation of stress in the oxide scale). We found that the alloys have lower values under the three criteria compared to pure Fe. The bcc alloy has the best score under a water rich environment and the fcc alloy is proven to be better for peak stress and summation of stress in the oxide scale under an oxygen rich environment. For surface segregation to occur, we find that a minimum content of Al or Cr in the near-surface region must be achieved. We also learned that the role of Al is more important than that of Cr in terms of corrosion resistant behavior at relatively higher temperatures for the Fe-Cr-Al ternary alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A parallel discrete dislocation dynamics/kinetic Monte Carlo method to study non-conservative plastic processes

Non-conservative processes play a fundamental role in plasticity and are behind important macroscopic phenomena such as creep, dynamic strain aging, loop raft formation, etc. In the most general case, vacancy-induced dislocation climb is the operating unit mechanism. While dislocation/vacancy interactions have been modeled in the literature using a variety of methods, the approaches developed rely on continuum descriptions of both the vacancy population and its fluxes. However, there are numerous situations in physics where point defect populations display heterogeneous concentrations and/or non-smooth kinetics. Here, a kinetic Monte Carlo (kMC) approach for modeling vacancy transport in response to arbitrary stress fields is used. Vacancies are treated as point particles and are coupled to the dislocation substructure representing a deformed material via an advection term defined by the local stress gradients. The stress fields and the dislocation substructure are evolved using a discrete dislocation dynamics (DDD) module. To extend the coupled model to the treatment of large systems, we have implemented it in the massively-parallel DDD code ParaDiS. To avoid numerical incompatibilities associated with merging deterministic (DDD) and stochastic (kMC) integration algorithms, we cast the entire elasto-plastic-diffusive problem within a single stochastic framework, taking advantage of a parallel kMC algorithm to evolve the system as a single event-driven process. The large-scale implementation enables the study of the evolution of a variety of dislocation-defect scenarios governed by non-conservative transport kinetics. After carrying out an exhaustive numerical and computational analysis of our parallel algorithm, we show results that emphasize situations where inhomogeneous vacancy dynamics are of relevance, and compare discrete kinetics to continuum solutions for several cases.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In Situ Raman Mapping of Si Island Electrodes and Stress Modeling as a Function of Lithiation and Size

Si is known for cracking and delamination during electrochemical cycling of a battery due to the large volume change associated with Li insertion and extraction. However, it has been found experimentally that patterned Si island electrodes that are 200 nm thick and less than 7 μm wide can deform in a purely elastic manner. Inspired by this, we performed in situ Raman stress characterization of model poly-crystalline Si island electrodes using an electrochemical cell coupled with an immersion objective lens and designed for a short working distance. A 5 μm wide Si island electrode showed a parabolic stress profile during lithiation, while for a 15 μm Si island electrode, a stress plateau in the center of the electrode was observed. A continuum model with coupled electro-chemo-mechanical (ECM) physics was established to understand the stress measurement. A qualitative agreement was reached between modeling and experimental data, and the critical size effect could be explained by the Li diffusive flux as governed by competition between the Li concentration and hydrostatic stress gradients. Below the critical size, the stress gradient drives Li toward the edges, where the electrode volume is free to expand, while above the critical size, the stress plateau inhibits Li diffusion to the edge and forces destructive stress relief by cracking. Furthermore, this work represents a promising methodology for in situ characterization of ECM coupling in battery electrodes, with suggestions provided for further improvement.

25 ENERGY STORAGE↗
DOE OSTI2022

Utah FORGE 2439: A Multi-Component Approach to Characterizing In-Situ Stress

Core-based in-situ stress estimation, Triaxial Ultrasonic Velocity (labTUV) data, and Deformation Rate Analysis (DRA) data for Utah FORGE well 16A(78)-32 using triaxial ultrasonic velocity and deformation rate analysis. Report documenting a multi-component approach to characterizing in-situ stress at the U.S. DOE FORGE EGS site: laboratory, modeling and field measurement. Core-based methods for in-situ stress estimation were applied using samples from 5 intervals within the Utah FORGE 16A(78)-32 well. At three of these locations, Triaxial Ultrasonic Velocity (labTUV) tests were performed, resulting in experimentally-determined relationships between wave velocities and stresses. Non-monotonic increase in the velocity-stress relationships are inferred provide evidence of stress history and are therefore used to estimate in-situ stress magnitudes. Additionally, Deformation Rate Analysis (DRA) tests were run on core plugs from various orientations at each of the 5 sampling locations. These, too, provide evidence of stress history based on stress-strain behavior. A novel Weight of Evidence (WoE) method was developed as a means of synthesizing in-situ stress evidence from these two types of tests. Results indicate the minimum horizontal stress gradient ranges from 0.58 psi/ft to 0.69 psi/ft, with 4 of the 5 values between 0.66 psi/ft and 0.69 psi/ft. The vertical stress gradient ranges from 1.05 psi/ft to 1.12 psi/ft, with 4 of the 5 zones given results between 1.09 psi/ft and 1.12 psi/ft. The maximum horizontal stress gradient ranges from 0.98 psi/ft to 1.34 psi/ft, with 4 of the 5 zones falling between 0.98 psi/ft and 1.24 psi/ft. The stress regime thus appears to be on the edge between normal faulting and strike-slip faulting, potentially flipping back and forth between the two regimes due to variability of rock properties, structures such as faults, and/or thermal anomalies.

15 GEOTHERMAL ENERGY↗
DOE OSTI2018

Spectroscopic and Computational Analysis of Chemical Pollutants Interactions on Steel - 18409

There is limited understanding of the scientific interaction of the chemical contaminants to DOE facility materials which can alter the stability of the materials, affecting the general safety. The resulting studies will have a direct impact towards developing an enhanced cost-effective decontamination method and understanding the negative effects caused by the chemical waste on the structural integrity of the solid surface in contact. First order kinematic models provide a better fit to the experimental data, implying that one layer of Hg adsorbs to the steel surface. Energy dispersive X-ray analysis confirmed that stainless steel samples are mainly composed of Fe, Ni, and Cr, and have a low carbon content. Objective: To determine the physiochemical interactions of Mercury (Hg) and Cesium (Cs) to steel and concrete using spectroscopic, adsorption and computational studies. To develop a multiscale simulation that shows the effects of adsorption and diffusion of alkali metals on the mechanical performance of steel alloys used in nuclear power plants. Approach: Molecular Dynamics (MD) simulations were used to compute the stress gradient generated in steel due to Hg adsorption. Finite element models were developed for simulating the effects of temperature and pressure in a diffusion analysis. Based on experimental data, one layer of Hg was used for the MD simulations. Material properties at the atomic level were determined from the MD simulations The stress gradient from the MD simulations is used as an input parameter in the FE simulation. Conclusions and Future Work: Computational methods such as MD and FE simulations were used to determine the effects of mercury adsorption in stainless steel samples. The adsorption process induces a stress gradient in the facility materials, which can affect the mechanical performance of facility materials under service. Tensile stresses help the diffusion process while compressive have the opposite effect. Temperature has a positive effect in the mass diffusion process. Future work will evaluate the effects of temperature on the material properties at the molecular level using both experimental and MD methods. Future work will evaluate the mechanical performance of facility materials at a wide range of environmental variables.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Characterization of electromigration-induced short-range stress development in Al(0.25 at. % Cu) conductor line

Scanning x-ray microbeam topography and fluorescence experiments were conducted in situ to study the electromigration behavior of a 0.5 μm thick, 10 μm wide, and 200 μm long Al(0.25 at. % Cu) conductor line with 1.5 μm-thick SiO2 passivation on a single crystal Si substrate. The strain sensitivity of x-ray topography measurement allowed detailed examination of the electromigration-induced stress distribution and evolution in the conductor line in response to the depletion of Cu solute early in the electromigration process. Upon electromigration at 0.4 MA/cm2 and 303 °C, a short-range stress gradient was quickly induced by Al migration in the Cu-depleted cathode region to counteract further Al flow. The stress gradient was fully developed during the 5.3 h incubation time, extending over the critical Blech length of about 66 μm from the cathode end. Plastic deformation then occurred at the downstream end of the Cu-depleted region. The preferential electromigration of Cu did not cause detectable stress change outside the Cu-depleted region, except for the significant stress development from the Al2Cu precipitation at the anode end which appeared to initiate the fracture in the passivation. Preliminary finite difference modeling was undertaken to simulate the experimental observations, from which important parameters dictating electromigration in Al(Cu) line were extracted: an apparent effective valence of −5.6 and −1.9 for Cu and Al in Al(Cu), respectively, and a critical Cu concentration of 0.16 at. % above which Al grain boundary diffusion is effectively blocked.

Physics↗
DOE OSTI2019

Hillock formation in co-deposited thin films of immiscible metal alloy systems

Hillocks are protruding sections of a surface that can influence the electronic and mechanical properties of a thin film. In monolithic films, these hillocks are formed due to thermally induced stress gradients during deposition. In this study, the surface morphology of co-sputtered immiscible Cu-X (X is a body centered cubic (BCC) group V or VI metal) thin films is characterized to elucidate the conditions that lead to hillock formation. Cu-Ta and Cu-Mo-Ag films were co-deposited with physical vapor deposition (PVD) magnetron sputtering at 25, 400, 600, and 800°C. A significant number of homogeneously distributed surface hillocks were observed only in the 600 and 800°C films. High-angle annular dark field (HAADF) cross-sectional imaging revealed significant Cu agglomerations underneath the protruding features. For the Cu-Ta films, the Cu was enveloped in a Cu-Ta nanocrystalline matrix. For Cu-Mo-Ag, the Cu was surrounded by Mo-Ag concentration modulations. While thermal stress gradients arise during deposition of immiscible metal films, biaxial stress calculations and literature cases reveal that they are not solely responsible for hillock formation. The observed morphologies align with a surface diffusion kinetic model that evaluates diffusion length of adatoms during deposition as a function of deposition temperature. Finally, this indicates a phase separation driving force paired with the constituent elements’ dissimilar mobilities at elevated deposition temperatures contribute to the presence of hillocks.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Three-dimensional local residual stress and orientation gradients near graphite nodules in ductile cast iron [3D local residual stress and orientation gradients near graphite nodules in ductile cast iron]

A synchrotron technique, differential aperture X-ray microscopy (DAXM), has been applied to characterize the microstructure and analyze the local mesoscale residual elastic strain fields around graphite nodules embedded in ferrite matrix grains in ductile cast iron. Compressive residual elastic strains are measured with a maximum strain of ~6.5–8 × 10 –4 near the graphite nodules extending into the matrix about 20 μm, where the elastic strain is near zero. The experimental data are compared with a strain gradient calculated by a finite element model, and good accord has been found but with a significant overprediction of the maximum strain. This is discussed in terms of stress relaxation during cooling or during storage by plastic deformation of the nodule, the matrix or both. Furthermore, relaxation by plastic deformation of the ferrite is demonstrated by the formation of low energy dislocation cell structure also quantified by the DAXM technique.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Geomechanical Characterization of the Mount Simon Sandstone and Eau Claire Formation of Northern Illinois Basin

The purpose of this paper is to analyze publicly available geomechanical data from two carbon storage sites in the Illinois Basin: the Illinois Basin-Decatur Project (IBDP) in Macon County, IL and the FutureGen2.0 project in Morgan County, IL, cancelled before injection began. This study estimates the magnitudes and directions of the least compressive principal stress gradient using hydraulic fracture-based stress measurement tests, borehole breakouts, and sonic logs in the Eau Claire Formation (primary confining zone) and the Mount Simon Sandstone (targeted reservoir). The range of stresses expected in the underlying Precambrian basement is also investigated. The evaluation of the state of stress is carried out in a probabilistic manner using the State of Stress Analysis Tool (SOSAT) developed under the National Risk Assessment Partnership (NRAP) program. Finally, the paper also provides a discussion on distinctions between fracture initiation pressure, propagation pressure, and fracture closure pressure, given that hydraulic fracture testing results show a significant difference between these three values. The discussion also addresses why the fracture closure pressure should be preferred in injection pressure determinations, a critical point in geological carbon storage projects.

de Toledo Camargo, Julia↗
DOE OSTI2025

From subsidies to stressors: Positively skewed ecological gradients alter biological responses to nutrients in streams

Abstract Subsidy–stress gradients offer a useful framework for understanding ecological responses to perturbation and may help inform ecological metrics in highly modified systems. Historic, region‐wide shifts from bottomland hardwood forest to row crop agriculture can cause positively skewed impact gradients in alluvial plain ecoregions, resulting in tolerant organisms that typically exhibit a subsidy response (increased abundance in response to environmental stressors) shifting to a stress response (declining abundance at higher concentrations). As a result, observed biological tolerance in modified ecosystems may differ from less modified regions, creating significant challenges for detecting biological responses to restoration efforts. Using the agriculturally dominated Mississippi Alluvial Plain (MAP) ecoregion in Mississippi, USA, as a case study, we tested the hypothesis that macroinvertebrate taxa that typically display a subsidy response to nutrient enrichment in less modified ecoregions (i.e., nutrient‐tolerance) shift to a stress response to increasing nutrients in highly modified watersheds with elevated baseline nutrient conditions (i.e., nutrient intolerance). The abundance and diversity of MAP‐specific intolerant taxa identified with threshold indicator taxa analysis were either unresponsive or exhibited a subsidy response to increasing nutrients in less modified ecoregions in Mississippi with less land alteration and lower nutrient concentrations, but declined at higher concentrations, providing evidence for a stress response to elevated nutrients in the MAP. Additionally, MAP‐specific tolerant and intolerant taxa richness responded to increased nutrients predictably and consistently across space and time within the MAP. However, in MAP streams, elevated specific conductance was predicted to dampen the response of tolerant and intolerant taxa richness to increasing nutrient concentrations, highlighting the importance of considering multistressor interactions when interpreting biological data. Lastly, we demonstrate the efficacy of this approach with sediment bacterial communities characterized with amplicon sequencing, which lack sufficient life history characteristics necessary for the development of multimetric indices. Both macroinvertebrate and bacterial communities responded similarly to increasing nutrient concentrations, suggesting DNA‐based approaches may provide an efficient biological assessment tool for monitoring water quality improvements in highly modified watersheds.

DeVilbiss, Stephen E. [U.S. Geological Survey Lowe↗
DOE OSTI2019

Thickness dependence of Al 0.88 Sc 0.12 N thin films grown on silicon

The thickening behavior of aluminum scandium nitride (Al 0.88 Sc 0.12 N) films grown on Si(111) substrates has been investigated experimentally using X-ray diffraction (XRD), transmission electron microscopy (TEM), atomic force microscopy, and residual stress measurement. Al 0.88 Sc 0.12 N films were grown with thicknesses spanning 14 nm to 1.1 um. TEM analysis shows that the argon sputter etch used to remove the native oxide prior to deposition produced an amorphous, oxygen-rich surface, preventing epitaxial growth. XRD analysis of the films show that the A1ScN(002) orientation improves as the films thicken and the XRD A1ScN(002) rocking curve full width half maximum decreases to 1.34 q for the 1.1 pm thick film. XRD analysis shows that the unit cell is expanded in both the a- and c-axes by Sc doping; the a-axis lattice parameter was measured to be 3.172 ± 0.007 A and the c-axis lattice parameter was measured to be 5.000 ± 0.001 A, representing 1.96% and 0.44% expansions over aluminum nitride lattice parameters, respectively. The grain size and roughness increase as the film thickness increases. A stress gradient forms through the film; the residual stress grows more tensile as the film thickens, from -1.24 GPa to +8.5MPa.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Data from: "Colonisation of the alpine tundra by trees: alpine neighbours assist late-seral but not early-seral conifer seedlings"

This archive contains data used to support conclusions made in “Colonisation of the alpine tundra by trees: alpine neighbours assist late-seral but not early-seral conifer seedlings”, by Jabis et al., 2020. Data were collected in the alpine field location of the Alpine Treeline Warming Experiment (ATWE), on Niwot Ridge, in the Front Range of the Colorado Rocky Mountains, USA.This package includes survivorship and physiology data for limber pine (Pinus flexilis), Engelmann spruce (Picea engelmannii), and Rocky Mountain snowlover (Chionophila jamesii). Site climate data such as soil moisture and temperature are also included. This data package contains ten comma-separated-values (.csv) files, and two rich-text-format (.rtf) files all compressed within one folder named “Neighbor_data_repository.zip”. Both file types can be opened by text-edit softwares such as TextEdit (Mac) and Notepad (Windows). The files are also compatible with analyses softwares such as R. .csv files can also be opened by Microsoft Excel. Two geospatial datasets are also included in this archive: one keyhole markup language (.kml) file with four points marking the corners of the study site, and a compressed file containing two ESRI shapefiles (.shp). The .kml files can be opened with Google Earth or Google Maps, and the shapefiles can be opened using any geographic information system applications, including the entire ArcGIS suite, and QGIS. -------------------------------------------------------------------------------------------------------------------------------------------------------The elevation mountain treeline is expected to shift upward with climate warming, and seed germination and seedling survival are critical local controls on treeline expansion. Neighboring alpine plants, either through competition for resources or through altering the microclimate, can also affect seedling emergence and survival. We asked whether establishing tree seedlings and an alpine herb are similarly sensitive to alpine plant neighbours under ambient and altered climate. We imposed active heating, watering, and neighbor removal experiments for emerging conifer seedlings and an alpine herb.We compared target plant survival, photosynthetic efficiency, and water use efficiency under ambient and experimental conditions. Picea engelmannii seedlings showed lower survival compared with Pinus flexilis three weeks following neighbour removal, and after 1 year only survived in watered plots. Pinus seedlings responded to neighbour removal by lowering the quantum yield of photosynthesis (ϕPSII). Contrary to expectations from the stress gradient hypothesis, survival was reduced without neighbours near the low-elevation range limit of Chionophila jamesii.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Vacancy-mediated transport and segregation tendencies of solutes in fcc nickel under diffusional creep: A density functional theory study

The Nabarro-Herring (NH) diffusional creep theory postulates the vacancy-mediated transport of atoms under a stress gradient as the creep mechanism under low-stress and high-temperature conditions. In multicomponent alloys, we premise that this stress-assisted flow of vacancies to and from grain boundaries will produce elemental segregation. An observation of such segregation, validated with theoretical predictions, can provide the necessary experimental evidence for the occurrence of NH creep. Theoretical calculations of the segregation tendencies via analyzing the dominant solute diffusion mechanisms and the difference in diffusivities of the elements are therefore essential. To this end, this study applies density functional theory calculations of migration barriers and solute-vacancy binding energies as input to the self-consistent mean-field theory to assess the vacancy-mediated diffusion mechanisms, transport coefficients, and segregation tendencies of Co, Cr, Mo, Re, Ta, and W solutes in face-centered-cubic Ni. We find Co, Re, and W to be slow diffusers at high temperatures and Cr, Mo, and Ta to be fast diffusers. Further analysis shows that the slow diffusers tend to always enrich at vacancy sinks over a wide range of temperatures. In contrast, the fast diffusers show a transition from depletion to enrichment as the temperature lowers. Furthermore, our analysis of the segregation tendencies under tensile hydrostatic strains shows that slow diffusers are largely unaffected by the strain and favor enrichment. On the other hand, the fast diffusers exhibit high sensitivity to strain and their segregation tendency can transition from depletion to enrichment at a given temperature. Finally, the transport coefficients calculated in this work are expected to serve as input to mesoscale microstructure models to provide a more rigorous assessment of solute segregation under NH creep conditions.

36 MATERIALS SCIENCE↗