Search NASA⌕ Search

SEARCH · Search NASA

Results for “Superconducting properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The nontrivial effects of annealing on superconducting properties of Nb single crystals

The effect of annealing on the superconducting properties of niobium single crystals was studied using optical, magnetic, and scanning tunneling microscopy (STM) methods. Pieces of the same crystal boule were studied before and after the annealing at 800 ${^\circ}\textrm{C}$, 1400 ${^\circ}\textrm{C}$, and near the melting point of niobium (2477 ${^\circ}\textrm{C}$). The initial samples had a high hydrogen content and low-temperature imaging revealed large hydrides (hundreds of micrometers) appearing below 190 K. The formation of these large precipitates is already completely suppressed by annealing at 800 ${^\circ}\textrm{C}$. However, the overall superconducting properties of the annealed samples did not improve and, in fact, worsened. In particular, the superconducting transition temperature decreased, the upper critical field increased, and the pinning strength increased. In the STM study, the sample was annealed initially at 400 ${^\circ}\textrm{C}$, measured, annealed at 1700 ${^\circ}\textrm{C}$, and measured again. The STM revealed a ‘dirty’ superconducting gap with a significant spatial variation in tunneling conductance after annealing at 400 ${^\circ}\textrm{C}$. The clean gap was recovered after annealing at 1700 ${^\circ}\textrm{C}$. This is likely due to oxygen redistribution near the surface, which is always covered by oxide layers in as-grown crystals. Our results indicate that vacuum annealing at least up to 1400 ${^\circ}\textrm{C}$, while removing a large percentage of hydrogen, introduces additional nanosized defects, likely hydride precipitates, that act as efficient pair-breaking and pinning centers. The dimensionless scattering rate is estimated to have increased from $\Gamma = 0.2$ to about $\Gamma = 0.4$ after annealing at 1400 ${^\circ}\textrm{C}$. These results on single crystals differ drastically from those obtained in polycrystalline bulk niobium (i.e. cut from superconducting radio-frequency cavities), where annealing is known to have a significant positive effect that is attributed to the improvement of the crystalline structure masking the more subtle influence of the hydrides.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Cryogenic growth of aluminum: Structural morphology, optical properties, superconductivity, and microwave dielectric loss

We explore the molecular beam epitaxy synthesis of superconducting aluminum thin films grown on c-plane sapphire substrates at cryogenic temperatures of 6 K and compare their behavior with films synthesized at room temperature. We demonstrate that cryogenic growth increases structural disorder, producing crystalline grains that modify the optical, electrical, and superconducting properties of aluminum. We observe that cryogenic deposition changes the color of aluminum from fully reflective to yellow and correlate the pseudodielectric function and reflectance with structural changes in the film. We find that smaller grain sizes enhance the superconductivity of aluminum, increasing its critical temperature and critical field. We then estimate the superconducting gap and coherence length of Cooper pairs in aluminum in the presence of disorder. In conclusion, we fabricate superconducting microwave resonators on these films and find that, independently of the growth temperature, the system is dominated by two-level system loss with similar quality factors in the high- and low-power regimes. We further measure a higher kinetic inductance in the cryogenically grown films.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Signatures of enhanced superconducting properties in niobium cavities

Superconducting radio-frequency (SRF) niobium cavities are critical for modern particle accelerators, as well as for advancing superconducting quantum systems and enabling ultrasensitive searches for new physics. In this work, we report a systematic observation of an anomalous frequency dip in Nb cavities, which occurs at temperatures just below the critical temperature (𝑇𝑐 ), indicative of enhanced superconducting properties at 𝑇 ≪ 𝑇 𝑐 . The magnitude of this dip is strongly correlated with the rf surface resistance, impurity distribution near the surface, and 𝑇𝑐 . Additionally, we report measurements of the coherence peak in the ac conductivity of two Nb SRF cavities processed using distinct methods. By comparing recent theories developed to model this experimental data, we show that the frequency-dip feature, larger coherence peak height, and reduction in the temperature-dependent surface resistance with rf current occur at minimal but finite levels of disorder.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Correlation between thickness dependent nanoscale structural chemistry and superconducting properties of ultrathin epitaxial NbN films

NbN-based superconductors have attracted interest for superconducting circuits, quantum computation and high frequency devices. The superconducting properties of NbN films are predominately reliant on the microstructure, therefore, an atomic-level understanding of the structure-chemistry is required to achieve high quality epitaxial NbN films. Here, in this study, the thickness-dependent superconducting properties of NbN films (5, 10, and 50 nm) within NbN/AlN/Al 2 O 3 heterostructures are investigated. NbN and AlN were epitaxially grown by an industrial scale physical vapor deposition technique. The role of nanoscale chemistry on the ultrathin NbN superconducting film is investigated at the atomic level for the first time via atom probe tomography, providing three-dimensional atomic distribution, chemical homogeneity, effect of impurities, specially, in secondary phase formations and interfacial abruptness. The NbN film with 5 nm of thickness demonstrates a superconducting transition temperature of 11.2 K as compared to 50 nm NbN films with a transition temperature of 15.3 K. These thickness dependent variation of superconducting properties are associated with the chemical inhomogeneity in terms of in-plane N:Nb distribution, secondary phase formations and NbN/AlN interfacial abruptness as a function of the NbN films thicknesses. The analysis depicts the interplay between the surface/interface and the superconducting properties of ultrathin NbN films. These results provide insights on material design and growth that will enable the development of optimized superconducting NbN films for quantum devices.

36 MATERIALS SCIENCE↗
NASA NTRS1995

Effect of Nb2O5 and V2O5 addition on the superconducting properties of YBa2Cu3O(y) thin films

The effect of Nb2O5 and V2O5 addition on the superconducting properties and microstructure of YBa2Cu3O(y) has been studied in thin films. Polycrystalline targets for laser ablation were prepared by mixing high purity V2O5 or Nb2O5 powders with a well characterized YBa2Cu3O(y) powder in the range 0 to 4 wt percent by solid state reaction method. Thin films (approximately 1500 A thickness) of the above targets were grown on (100) SrTiO3 (STO) and (100) LaAlO3 (LAO) substrates at 700 C temperature by pulsed laser deposition (PLD) technique. In the case of Nb2O5 addition we have noticed an increase in J(sub c) up to 0.5 wt percent and higher additive concentration (greater than 0.5 wt percent) have degraded the superconducting properties. However, in the case of V2O3 addition, there is an improvement in current density and microstructural properties up to 1 wt percent and the superconducting properties degrade for concentrations greater than 1 wt percent. The best J(sub c) for 0.5 wt percent of Nb2O5 added YBCO thin film is 1.6 x 10(exp 6) A/sq cm and for that of V2O5 added sample is 3.4 x 10(exp 6) A/sq cm at 77 K as compared to the pure YBa2Cu3O(y) (YBCO) film J(sub c) (1.2 x 10(exp 6) A/sq cm) observed on STO substrates. The reason for improvement in J(sub c) and microstructural properties in the case of V2O5 addition could be due to the low melting of V2O5 (690 C) which can act as a very good surfactant during deposition. Over all, we have realized that Nb2O5 addition or V2O5 addition to YBCO have shown significant improvement over the undoped YBa2Cu3O(7-x) films grown under identical conditions.

Srinivas, S.↗
DOE OSTI2020

Effect of Co 2 N impurity on the superconducting properties of δ-MoN thin films grown by polymer assisted deposition

We report the effect of Co 2 N impurity on the superconducting properties of δ-MoN thin films grown by polymer-assisted deposition on c-cut sapphire (Al 2 O 3 ). The films show a superconducting transition temperature of 10.4 K and an upper critical field H c2 (0) perpendicular to the film surface around 3 T. The latter corresponds to a relatively large coherence length ξ, which enhances the two-dimensional limit when the magnetic field is applied parallel to the film surface. In comparison with pure δ-MoN films, the inclusion of Co 2 N impurity in the δ-MoN films could significantly modify the critical current density at the vortex-free state. In conclusion, the ability to tune the superconducting properties of metal-nitride superconductors by introducing chemically and structurally compatible impurity may find potential applications for superconducting single-photon detectors.

36 MATERIALS SCIENCE↗
DOE OSTI2025

What causes the variation in superconducting properties of UTe 2 ?

Reaching a consensus on the superconducting order parameter of unconventional superconductors remains a central challenge in the field of magnetically-mediated superconductivity. Though UTe 2 is largely accepted as a rare example of an odd-parity superconductor, its precise order parameter remains highly debated, even at ambient conditions. A key underlying issue is the large sample-to-sample variation in superconducting properties at zero applied pressure and magnetic field. Here, we investigate the origin of the observed variation by means of single crystal x-ray diffraction (SC-XRD) and scanning transmission electron microscopy (STEM) measurements. Our results reveal highly ordered crystalline lattices, in agreement with the expected Immm structure, and no signs of uranium vacancies. Tiny amounts of interstitial defects, however, are observed on the Te2 layers that host Te chains along the b axis. We argue that these defects give rise to slightly enhanced atomic displacement parameters observed in SC-XRD data and are enough to disrupt the unconventional superconducting state in UTe 2 . Our findings highlight the need to focus future order parameter determination efforts on single crystals of UTe 2 with minimal amounts of structural disorder.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1972

Ultrasonic investigation of the superconducting properties of the Nb-Mo system

The superconducting properties of single crystals of Nb and two alloys of Nb with Mo were investigated by ultrasonic techniques. The results of measurements of the ultrasonic attenuation and velocities as a function of temperature, Mo composition, crystallographic direction, and ultrasonic frequency are reported. The attenuation and small velocity changes associated with the superconductivity of the samples are shown to be dependent on the sample resistivity ratio which varied from 4.3 for Nb-9% Mo to 6500 for pure Nb. The ultrasonic attenuation data are analyzed in terms of the superconducting energy gap term of the BCS theory. A new model is proposed for the analysis of ultrasonic attenuation in pure superconductors with two partially decoupled energy bands. To analyze the attenuation in pure superconducting Nb, the existence of two energy gaps was assumed to be associated with the two partially decoupled energy bands. One of the gaps was found to have the normal BCS value of 3.4 and the other gap was found to have the anomalously large value of 10. No experimental evidence was found to suggest that the second energy gap had a different transition temperature. The interpretation of the results for the Nb-Mo alloys is shown to be complicated by the possible existence of a second superconducting phase in Nb-Mo alloys with a transition temperature of 0.35 of the transition temperature of the first phase. The elastic constants of Nb and Nb-Mo alloys are shown to be approximately independent of Mo composition to nine atomic percent Mo. These results do not agree with the current microscopic theory of transition temperature for the transition elements.

Lacy, L. L.↗
DOE OSTI2023

Effects of anisotropy and disorder on the superconducting properties of niobium

We report results for the superconducting transition temperature and anisotropic energy gap for pure niobium based on Eliashberg’s equations and electron and phonon band structures computed from density functional theory. The electronic band structure is used to construct the Fermi surface and calculate the Fermi velocity at each point on the Fermi surface. The phonon bands are in excellent agreement with inelastic neutron scattering data. The corresponding phonon density of states and electron–phonon coupling define the electron–phonon spectral function, α 2 F(p, p'; ω), and the corresponding electron–phonon pairing interaction, which is the basis for computing the superconducting properties. The electron–phonon spectral function is in good agreement with existing tunneling spectroscopy data except for the spectral weight of the longitudinal phonon peak at ℏω LO = 23 meV. We obtain an electron–phonon coupling constant of λ = 1.057, renormalized Coulomb interaction μ* = 0.218, and transition temperature T c = 9.33 K. The corresponding strong-coupling gap at T = 0 is modestly enhanced, Δ 0 = 1.55 meV, compared to the weak-coupling BCS value $Δ^{\text {wc}}_{0}$ = 1.78 k B T c = 1.43 meV. The superconducting gap function exhibits substantial anisotropy on the Fermi surface. We analyze the distribution of gap anisotropy and compute the suppression of the superconducting transition temperature using a self-consistent T-matrix theory for quasiparticle-impurity scattering to describe niobium doped with non-magnetic impurities. We compare these results with experimental results on niobium SRF cavities doped with nitrogen impurities.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Impact of Annealing on Superconducting Properties of Tantalum Thin Films

The pursuit for higher-coherence superconducting qubits has led to the adoption of new materials and innovative fabrication techniques. Among the commonly used superconducting materials, tantalum-based or tantalum-capped superconducting qubits have demonstrated the longest lifetimes, outperforming niobium devices even in the presence of their native oxides. Given the losses introduced by the surface oxide, one method to further improve performance is to reduce or eliminate the native oxide on tantalum through UHV annealing. In this work, we examine the effect of dissolved oxygen as a function of annealing temperature on the superconducting properties of tantalum thin films. Dissolved oxygen is quantified using atom probe tomography (APT) and secondary ion mass spectrometry (TOF-SIMS) and correlated with electromagnetic transport measurements performed using a Physical Property Measurement System (PPMS). This study observes that annealing decomposes the native oxide and drives oxygen diffusion into the film matrix. Increasing oxygen content decreases the superconducting transition temperature (Tc) and the residual resistivity ratio (RRR). The critical field decreases with the incorporation of oxygen, while the film’s coherence length decreases relatively by 5%. These results, as well as findings from ongoing studies linking fabrication processes to the structural and chemical properties of the superconducting film and Josephson junction, provide insight into effective strategies for improving the performance of superconducting devices.

Shinde, Maithilee [IIT, Chicago; Fermilab]↗
DOE OSTI2020

Electron Tunneling and X-Ray Photoelectron Spectroscopy Studies of the Superconducting Properties of Nitrogen-Doped Niobium Resonator Cavities

Scanning tunneling microscopy and spectroscopy and X-ray photoelectron spectroscopy (XPS) have been used to investigate the differences between the surface electronic structures and chemical structure of typically prepared and N-doped Nb cutouts from superconducting radio frequency (SRF) cavities. The goal of this work is to get insights into the fundamental physics and materials mechanisms behind the striking decrease of the surface resistance with the radiofrequency magnetic field, which has been observed by many groups on N-doped Nb cavities. In particular, we address the effects of N-doping on the superconducting properties at the surface of SRF cavities. XPS measurements reveal a significantly more oxidized Nb 3d states on the N-doped Nb surfaces which is confirmed by tunneling spectroscopy measurements. Analysis of the tunneling spectra in the framework of a recent model (A. Gurevich and T. Kubo Phys. Rev. B 96, 184515 (2017)) shows that the N-doping greatly reduces local distribution of superconducting properties on the surface, causes a significant shrinkage of the metallic suboxide and changes the contact resistance between the metallic suboxide and the bulk niobium toward an optimum value, resulting in a lower surface resistance. Combination of these factors enables one to effectively tune the density of states at the surface and to reveal the decrease of the surface resistance with the radio frequency field which follows from the BCS theory. A slightly reduced average gap and a smaller coherence length, revealed by tunneling spectroscopy in the vortex cores, have been found in the N-doped Nb samples compared to typically prepared Nb samples, indicating a stronger impurity scattering caused by nitrogen doping in a moderately disordered material.

Lechner, Eric M.↗
NASA NTRS1995

A study of the superconducting properties of YBa2Cu(9-x)Nb(x)O(y) thin films

Effect of Niobium substitution at the copper site in YBa2Cu3O(7-x) was studied in thin film form. The films were deposited by laser ablation technique using the targets of the YBa2Cu(3-x)Nb(x)O(y) where x = 0.0, 0.025, 0.05, 0.1, 0.2, 0.4, 0.8 and 1.0 under identical deposition conditions on SrTiO3 (100) substrates. Films were characterized by XRD, resistivity, I-V and J(sub c) measurements. Films made from x = 0.025 and 0.05 concentrations of Nb substituted targets showed relatively improved superconducting properties compared to that of undoped films. the best J(sub c) realized for x - 0.025 Nb concentration was 1.8 x 10(exp 6) A/sq cm and for 0.05 Nb concentration it was 3.2 x 10(exp 6) A/sq cm at 77 K. However, degradation of the superconducting properties, with the increase of x is greater than or equal to 0.1 Nb concentration and drastic suppression and complete loss of superconductivity was noticed for x is greater than or equal to 0.4. The growth of impurity phase YBa2NbO6 for x = 0.1 and above of Nb concentration was noted from XRD (X-Ray Diffraction) patterns. However, the site occupancy of Nb could not be confirmed from these studies.

Srinivas, S.↗
NASA NTRS1981

Susceptibility measurements on the superconducting properties of Nb-Ge alloys

A susceptibility apparatus to measure superconducting properties of samples made in the MSFC Drop Tube was used to measure the transition temperature (Tc) and susceptibilities of Nb and Nb Ge Alloys prepared in bulk spherical (2-4 mm diameter) form using a 32 m drop tube in which containerless low gravity solidification could take place. Results indicate that a drop tube processing environment was beneficial for increasing the Tc of the superconducting phase of the material over that of arc melted material. The increase in Tc is found to be related to the amount of solidification of the total sample that took place before reaching the bottom of the drop tube. In phase and quadrature phase measurements of the specimen's susceptibility indicated that some improvement in homogeneity takes place in drop tube processing. These phase measurements also indicated little or no shielding of a lower Tc phase by a higher Tc filamentary structure.

Rathz, T. J.↗
DOE OSTI2020

Effect of layer thickness on structural, morphological and superconducting properties of Nb 3 Sn films fabricated by multilayer sequential sputtering

Superconducting Nb3Sn films can be synthesized by controlling atomic concentration of Sn. Multilayer sequential sputtering of Nb and Sn thin films followed by high temperature annealing is considered as a method to fabricate Nb3Sn films where Sn composition of deposited films can be controlled by controlling the thickness of alternating Nb and Sn layers. We report on the structural, morphological and superconducting properties of Nb3Sn films fabricated by multilayer sequential sputtering of Nb and Sn films on sapphire substrates with ex-situ annealing at 950 °C for 3 h. We have investigated the effect of Nb and Sn layer thickness on the properties of Nb3Sn films. The thicknesses of Nb and Sn layers were varied in two ways: (1) varied Nb:Sn thickness ratio (1:1, 2:1, 3:1, 4:1), and (2) varied layer thickness of both Nb and Sn layers, while keeping constant Nb:Sn thickness ratio of 2:1. The crystal structure, surface morphology, topography, and film composition were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and energy dispersive X-ray spectroscopy (EDS) respectively. The results showed Sn loss from the surface due to evaporation during annealing. Superconducting Nb3Sn films of critical temperature up to 17.93 K have been achieved.

Sayeed, M. N.↗