Search NASA⌕ Search

SEARCH · Search NASA

Results for “Superconducting property”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The nontrivial effects of annealing on superconducting properties of Nb single crystals

The effect of annealing on the superconducting properties of niobium single crystals was studied using optical, magnetic, and scanning tunneling microscopy (STM) methods. Pieces of the same crystal boule were studied before and after the annealing at 800 ${^\circ}\textrm{C}$, 1400 ${^\circ}\textrm{C}$, and near the melting point of niobium (2477 ${^\circ}\textrm{C}$). The initial samples had a high hydrogen content and low-temperature imaging revealed large hydrides (hundreds of micrometers) appearing below 190 K. The formation of these large precipitates is already completely suppressed by annealing at 800 ${^\circ}\textrm{C}$. However, the overall superconducting properties of the annealed samples did not improve and, in fact, worsened. In particular, the superconducting transition temperature decreased, the upper critical field increased, and the pinning strength increased. In the STM study, the sample was annealed initially at 400 ${^\circ}\textrm{C}$, measured, annealed at 1700 ${^\circ}\textrm{C}$, and measured again. The STM revealed a ‘dirty’ superconducting gap with a significant spatial variation in tunneling conductance after annealing at 400 ${^\circ}\textrm{C}$. The clean gap was recovered after annealing at 1700 ${^\circ}\textrm{C}$. This is likely due to oxygen redistribution near the surface, which is always covered by oxide layers in as-grown crystals. Our results indicate that vacuum annealing at least up to 1400 ${^\circ}\textrm{C}$, while removing a large percentage of hydrogen, introduces additional nanosized defects, likely hydride precipitates, that act as efficient pair-breaking and pinning centers. The dimensionless scattering rate is estimated to have increased from $\Gamma = 0.2$ to about $\Gamma = 0.4$ after annealing at 1400 ${^\circ}\textrm{C}$. These results on single crystals differ drastically from those obtained in polycrystalline bulk niobium (i.e. cut from superconducting radio-frequency cavities), where annealing is known to have a significant positive effect that is attributed to the improvement of the crystalline structure masking the more subtle influence of the hydrides.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Cryogenic growth of aluminum: Structural morphology, optical properties, superconductivity, and microwave dielectric loss

We explore the molecular beam epitaxy synthesis of superconducting aluminum thin films grown on c-plane sapphire substrates at cryogenic temperatures of 6 K and compare their behavior with films synthesized at room temperature. We demonstrate that cryogenic growth increases structural disorder, producing crystalline grains that modify the optical, electrical, and superconducting properties of aluminum. We observe that cryogenic deposition changes the color of aluminum from fully reflective to yellow and correlate the pseudodielectric function and reflectance with structural changes in the film. We find that smaller grain sizes enhance the superconductivity of aluminum, increasing its critical temperature and critical field. We then estimate the superconducting gap and coherence length of Cooper pairs in aluminum in the presence of disorder. In conclusion, we fabricate superconducting microwave resonators on these films and find that, independently of the growth temperature, the system is dominated by two-level system loss with similar quality factors in the high- and low-power regimes. We further measure a higher kinetic inductance in the cryogenically grown films.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Signatures of enhanced superconducting properties in niobium cavities

Superconducting radio-frequency (SRF) niobium cavities are critical for modern particle accelerators, as well as for advancing superconducting quantum systems and enabling ultrasensitive searches for new physics. In this work, we report a systematic observation of an anomalous frequency dip in Nb cavities, which occurs at temperatures just below the critical temperature (𝑇𝑐 ), indicative of enhanced superconducting properties at 𝑇 ≪ 𝑇 𝑐 . The magnitude of this dip is strongly correlated with the rf surface resistance, impurity distribution near the surface, and 𝑇𝑐 . Additionally, we report measurements of the coherence peak in the ac conductivity of two Nb SRF cavities processed using distinct methods. By comparing recent theories developed to model this experimental data, we show that the frequency-dip feature, larger coherence peak height, and reduction in the temperature-dependent surface resistance with rf current occur at minimal but finite levels of disorder.

43 PARTICLE ACCELERATORS↗
NASA NTRS1995

Effect of Nb2O5 and V2O5 addition on the superconducting properties of YBa2Cu3O(y) thin films

The effect of Nb2O5 and V2O5 addition on the superconducting properties and microstructure of YBa2Cu3O(y) has been studied in thin films. Polycrystalline targets for laser ablation were prepared by mixing high purity V2O5 or Nb2O5 powders with a well characterized YBa2Cu3O(y) powder in the range 0 to 4 wt percent by solid state reaction method. Thin films (approximately 1500 A thickness) of the above targets were grown on (100) SrTiO3 (STO) and (100) LaAlO3 (LAO) substrates at 700 C temperature by pulsed laser deposition (PLD) technique. In the case of Nb2O5 addition we have noticed an increase in J(sub c) up to 0.5 wt percent and higher additive concentration (greater than 0.5 wt percent) have degraded the superconducting properties. However, in the case of V2O3 addition, there is an improvement in current density and microstructural properties up to 1 wt percent and the superconducting properties degrade for concentrations greater than 1 wt percent. The best J(sub c) for 0.5 wt percent of Nb2O5 added YBCO thin film is 1.6 x 10(exp 6) A/sq cm and for that of V2O5 added sample is 3.4 x 10(exp 6) A/sq cm at 77 K as compared to the pure YBa2Cu3O(y) (YBCO) film J(sub c) (1.2 x 10(exp 6) A/sq cm) observed on STO substrates. The reason for improvement in J(sub c) and microstructural properties in the case of V2O5 addition could be due to the low melting of V2O5 (690 C) which can act as a very good surfactant during deposition. Over all, we have realized that Nb2O5 addition or V2O5 addition to YBCO have shown significant improvement over the undoped YBa2Cu3O(7-x) films grown under identical conditions.

Srinivas, S.↗
DOE OSTI2025

What causes the variation in superconducting properties of UTe 2 ?

Reaching a consensus on the superconducting order parameter of unconventional superconductors remains a central challenge in the field of magnetically-mediated superconductivity. Though UTe 2 is largely accepted as a rare example of an odd-parity superconductor, its precise order parameter remains highly debated, even at ambient conditions. A key underlying issue is the large sample-to-sample variation in superconducting properties at zero applied pressure and magnetic field. Here, we investigate the origin of the observed variation by means of single crystal x-ray diffraction (SC-XRD) and scanning transmission electron microscopy (STEM) measurements. Our results reveal highly ordered crystalline lattices, in agreement with the expected Immm structure, and no signs of uranium vacancies. Tiny amounts of interstitial defects, however, are observed on the Te2 layers that host Te chains along the b axis. We argue that these defects give rise to slightly enhanced atomic displacement parameters observed in SC-XRD data and are enough to disrupt the unconventional superconducting state in UTe 2 . Our findings highlight the need to focus future order parameter determination efforts on single crystals of UTe 2 with minimal amounts of structural disorder.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1972

Ultrasonic investigation of the superconducting properties of the Nb-Mo system

The superconducting properties of single crystals of Nb and two alloys of Nb with Mo were investigated by ultrasonic techniques. The results of measurements of the ultrasonic attenuation and velocities as a function of temperature, Mo composition, crystallographic direction, and ultrasonic frequency are reported. The attenuation and small velocity changes associated with the superconductivity of the samples are shown to be dependent on the sample resistivity ratio which varied from 4.3 for Nb-9% Mo to 6500 for pure Nb. The ultrasonic attenuation data are analyzed in terms of the superconducting energy gap term of the BCS theory. A new model is proposed for the analysis of ultrasonic attenuation in pure superconductors with two partially decoupled energy bands. To analyze the attenuation in pure superconducting Nb, the existence of two energy gaps was assumed to be associated with the two partially decoupled energy bands. One of the gaps was found to have the normal BCS value of 3.4 and the other gap was found to have the anomalously large value of 10. No experimental evidence was found to suggest that the second energy gap had a different transition temperature. The interpretation of the results for the Nb-Mo alloys is shown to be complicated by the possible existence of a second superconducting phase in Nb-Mo alloys with a transition temperature of 0.35 of the transition temperature of the first phase. The elastic constants of Nb and Nb-Mo alloys are shown to be approximately independent of Mo composition to nine atomic percent Mo. These results do not agree with the current microscopic theory of transition temperature for the transition elements.

Lacy, L. L.↗
DOE OSTI2026

Impact of Annealing on Superconducting Properties of Tantalum Thin Films

The pursuit for higher-coherence superconducting qubits has led to the adoption of new materials and innovative fabrication techniques. Among the commonly used superconducting materials, tantalum-based or tantalum-capped superconducting qubits have demonstrated the longest lifetimes, outperforming niobium devices even in the presence of their native oxides. Given the losses introduced by the surface oxide, one method to further improve performance is to reduce or eliminate the native oxide on tantalum through UHV annealing. In this work, we examine the effect of dissolved oxygen as a function of annealing temperature on the superconducting properties of tantalum thin films. Dissolved oxygen is quantified using atom probe tomography (APT) and secondary ion mass spectrometry (TOF-SIMS) and correlated with electromagnetic transport measurements performed using a Physical Property Measurement System (PPMS). This study observes that annealing decomposes the native oxide and drives oxygen diffusion into the film matrix. Increasing oxygen content decreases the superconducting transition temperature (Tc) and the residual resistivity ratio (RRR). The critical field decreases with the incorporation of oxygen, while the film’s coherence length decreases relatively by 5%. These results, as well as findings from ongoing studies linking fabrication processes to the structural and chemical properties of the superconducting film and Josephson junction, provide insight into effective strategies for improving the performance of superconducting devices.

Shinde, Maithilee [IIT, Chicago; Fermilab]↗
NASA NTRS1995

A study of the superconducting properties of YBa2Cu(9-x)Nb(x)O(y) thin films

Effect of Niobium substitution at the copper site in YBa2Cu3O(7-x) was studied in thin film form. The films were deposited by laser ablation technique using the targets of the YBa2Cu(3-x)Nb(x)O(y) where x = 0.0, 0.025, 0.05, 0.1, 0.2, 0.4, 0.8 and 1.0 under identical deposition conditions on SrTiO3 (100) substrates. Films were characterized by XRD, resistivity, I-V and J(sub c) measurements. Films made from x = 0.025 and 0.05 concentrations of Nb substituted targets showed relatively improved superconducting properties compared to that of undoped films. the best J(sub c) realized for x - 0.025 Nb concentration was 1.8 x 10(exp 6) A/sq cm and for 0.05 Nb concentration it was 3.2 x 10(exp 6) A/sq cm at 77 K. However, degradation of the superconducting properties, with the increase of x is greater than or equal to 0.1 Nb concentration and drastic suppression and complete loss of superconductivity was noticed for x is greater than or equal to 0.4. The growth of impurity phase YBa2NbO6 for x = 0.1 and above of Nb concentration was noted from XRD (X-Ray Diffraction) patterns. However, the site occupancy of Nb could not be confirmed from these studies.

Srinivas, S.↗
NASA NTRS1981

Susceptibility measurements on the superconducting properties of Nb-Ge alloys

A susceptibility apparatus to measure superconducting properties of samples made in the MSFC Drop Tube was used to measure the transition temperature (Tc) and susceptibilities of Nb and Nb Ge Alloys prepared in bulk spherical (2-4 mm diameter) form using a 32 m drop tube in which containerless low gravity solidification could take place. Results indicate that a drop tube processing environment was beneficial for increasing the Tc of the superconducting phase of the material over that of arc melted material. The increase in Tc is found to be related to the amount of solidification of the total sample that took place before reaching the bottom of the drop tube. In phase and quadrature phase measurements of the specimen's susceptibility indicated that some improvement in homogeneity takes place in drop tube processing. These phase measurements also indicated little or no shielding of a lower Tc phase by a higher Tc filamentary structure.

Rathz, T. J.↗
DOE OSTI2025

Superconducting properties of commercially available solders for low-field applications

Solders with superconducting transitions around 4K are useful in low magnetic field environments for AC current leads or in electrical and mechanical bonds. Accurate knowledge of these solders’ superconducting properties is essential for improving high precision experiments. We have measured the electrical resistance of five commercially-available eutectic or near-eutectic solders: 50%Sn-50%Pb, 60%Sn-40%Pb, 60%Sn-40%Pb-0.3%Sb, 52%In-48%Sn, and 96.5%Sn-3.5%Ag, down to 2.3K and in applied magnetic fields from 0 to 0.1 T . We report critical temperatures T c (B), 90%–10% transition widths ΔT c , and zero-temperature critical fields B c,0 . Our best candidate for low-loss AC current wiring in low fields is 50%Sn-50%Pb, which has a zero-field T c,0 = 7.1K (with ΔT c = 0.6 K), and remained high at T c (0.1 T) = 6.9K (ΔT c = 0.6K ). We also report, for the first time, T c and B c of 60%Sn-40%Pb-0.3%Sb and B c,0 of 96.5%Sn-3.5%Ag. Our T c,0 - 3.31K (ΔT c = 0.08K) for 96.5%Sn-3.5%Ag disagrees with a widely adopted value.

Hickman, C. [North Carolina State University, Rale↗
NASA NTRS1971

Superconducting properties as a function of thickness in NbN films.

Measurement of the superconducting properties of NbN films prepared by a high purity reactive sputtering process. The transition temperature was found to decrease with decreasing film thickness, while in contrast the critical current vs magnetic field was largely independent of film thickness and even slightly increased when the film thickness went down to 100 A. The average resistivity of the NbN films was 1000 microohm-cm.

Gavaler, J. R.↗
NASA NTRS1972

Superconducting properties of annealed Nb-Al-Ge thin films.

Discussion of the superconducting transition temperature and other superconducting properties of annealed Nb-Al-Ge thin films which were prepared by sputtering from a 3Nb-0.8Al-0.2Ge cathode. Annealing was performed in a high-vacuum environment maintained at 10 to the minus 9th torr or less, for times and temperatures near the optimum conditions for bulk Nb-Al-Ge. Films with transition temperatures from 12 to 16 K were annealed and in all cases a rise in transition temperature was observed, with the maximum value obtained thus far being 17.5 K. The current carrying capacity values, already substantially higher for unannealed thin films than for the bulk, were raised even further in the annealed samples, indicating that annealing has no detrimental effects on the flux pinning in these films.

Janocko, M. A.↗