Search NASA⌕ Search

SEARCH · Search NASA

Results for “Supersonic Laminar Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Low-Disturbance Flow Characteristics of the NASA-Ames Laminar Flow Supersonic Wind Tunnel

A unique, low-disturbance (quiet) supersonic wind tunnel has been commissioned at the NASA-Ames Fluid Mechanics Laboratory (FML) to support Supersonic Laminar Flow Control (SLFC) research. Known as the Laminar Flow Supersonic Wind Tunnel (LFSWT), this tunnel is designed to operate at potential cruise Mach numbers and unit Reynolds numbers (Re) of the High Speed Civil Transport (HSCT). The need to better understand the receptivity of the transition phenomena on swept (HSCT) wings to attachment-line contamination and cross-flows has provided the impetus for building the LFSWT. Low-disturbance or "quiet" wind tunnels are known to be an essential part of any meaningful boundary layer transition research. In particular, the receptivity of supersonic boundary layers to wind tunnel disturbances can significantly alter the transition phenomena under investigation on a test model. Consequently, considerable effort has gone into the design of the LFSWT to provide quiet flow. The paper describes efforts to quantify the low-disturbance flows in the LFSWT operating at Mach 1.6, as a precursor to transition research on wing models. The research includes: (1) Flow measurements in both the test section and settling chamber of the LFSWT, using a full range of measurement techniques; (2) Study of the state of the test section boundary layer so far by using a single hot-wire mounted above the floor centerline, with and without boundary layer trips fitted at the test section entrance; (3) The effect of flow quality of unsteady supersonic diffuser flow, joint steps and gaps, and wall vibration.

Wolf, Stephen W. D.↗
NASA NTRS1997

Quiet Flow Characteristics of the NASA-Ames Laminar Flow Supersonic Wind Tunnel for Mach 1.6 Transition Studies

Low-disturbance or 'quiet' wind tunnels are an essential part of any meaningful boundary layer transition research. In particular, the receptivity of supersonic boundary layers to wind tunnel disturbances can significantly alter the transition phenomena under investigation on a test model. Consequently, considerable study has gone into the design of a new wind tunnel to provide quiet (low-disturbance) flow, encompassing both theoretical and experimental efforts. Our pilot (eighth-scale) supersonic wind tunnel was reported in 1992. NASA-Ames Fluid Mechanics Laboratory (FML) commissioned a quiet wind tunnel in 1994 to support Supersonic Laminar Flow Control (SLFC) research. Known as the Laminar Flow Supersonic Wind Tunnel (LFSWT), this tunnel is designed to operate at potential cruise Mach numbers and unit Reynolds numbers (Re) of the High Speed Civil Transport (HSCT). The need to better understand the transition phenomena on the leading edge region of swept (HSCT) wings provided the impetus for building the LFSWT. Additional information is contained in the original extended abstract.

Wolf, Stephen W. D.↗
NASA NTRS1973

Base pressure in laminar supersonic flow.

An asymptotic description is proposed for supersonic laminar flow over a wedge or a backward-facing step, for large Reynolds number and for a base or step height which is small compared with the boundary-layer length. The analysis is carried out for adiabatic wall conditions and a viscosity coefficient proportional to temperature. In a particular limit corresponding to a very thick boundary layer, a similarity law is obtained for the base pressure. For a thinner boundary layer an asymptotic form for the base pressure is obtained which shows the dependence on the parameters explicitly and which permits good agreement with experiment. This latter result is based on an inviscid-flow approximation for the corner expansion and for reattachment with viscous forces important primarily in a thin sublayer about the dividing streamline. A prediction of the pressure distribution at reattachment is given and the result is compared with experimental pressure distributions.

Messiter, A. F.↗
NASA NTRS1995

Supersonic laminar flow control research

The objective is to understand supersonic laminar flow stability, transition, and active control. Some prediction techniques will be developed or modified to analyze laminar flow stability. The effects of distributed heating and cooling as an active boundary layer control technique will be studied. The primary tasks of the research apply to the NASA/Ames Proof of Concept (PoC) and Laminar Flow Supersonic Wind Tunnel's (LFSWT's) nozzle design with laminar flow control and are listed as follows: (1) predictions of supersonic laminar boundary layer stability and transition, (2) effects of wall heating and cooling on supersonic laminar flow control, (3) performance evaluation of the PoC and LFSWT nozzle designs with wall heating and cooling applied at different locations and various lengths, and (4) effects of a conducted versus pulse wall temperature distribution for the LFSWT.

Lo, Ching F.↗
NASA NTRS1991

Application of laminar flow control to the High Speed Civil Transport - The NASA Supersonic Laminar Flow Control Program

The NASA Supersonic Laminar Flow Control (SLFC) program encompasses the development of refined CFD methods and boundary layer stability codes for the highly 3D supersonic flow conditions encountered by the F-16XL technology demonstration aircraft and the prospective High Speed Civil Transport (HSCT). While the F-16XL-1 aircraft continues to gather SLFC data, work is under way on the F-16XL-2 aircraft: which will furnish attach-line design criteria, code-calibration data, and an improved understanding of the flowfield over a wing that will add confidence to the design of HSCTs' boundary layer-controlling air-suction panels.

Fischer, Michael C.↗
NASA NTRS1996

Supersonic Laminar Flow Control Research

The objective of this research is to understand supersonic laminar flow stability, transition and active control. Some prediction techniques are developed or modified to analyze laminar flow stability. The effects of distributed heating and cooling as an active boundary layer control technique are studied. The primary tasks of the research apply to the NASA/Ames Proof-of-Concept (PoC) and the Laminar Flow Supersonic Wind Tunnel's (LFSWT's) nozzle design with laminar flow control and are listed as follows: (1) Predictions of supersonic laminar boundary layer stability and transition; (2) Effects of wall heating and cooling on supersonic laminar flow control on a flat plate; (3) Performance evaluation of the PoC and LFSWT nozzle designs with wall heating and cooling applied at different locations and various lengths; (4) Effects of a conducted -vs- pulse wall temperature distribution for the LFSWT; and (5) Application of wall heating and/or cooling to laminar boundary layer and flow separation control of airfoils and investigation of related active control techniques.

Lo, C. F.↗
NASA NTRS1994

Supersonic laminar flow control research

The objective of the research is to understand supersonic laminar flow stability, transition, and active control. Some prediction techniques will be developed or modified to analyze laminar flow stability. The effects of supersonic laminar flow with distributed heating and cooling on active control will be studied. The primary tasks of the research applying to the NASA/Ames Proof of Concept (POC) Supersonic Wind Tunnel and Laminar Flow Supersonic Wind Tunnel (LFSWT) nozzle design with laminar flow control are as follows: (1) predictions of supersonic laminar boundary layer stability and transition, (2) effects of wall heating and cooling for supersonic laminar flow control, and (3) performance evaluation of POC and LFSWT nozzles design with wall heating and cooling effects applying at different locations and various length.

Lo, Ching F.↗
NASA NTRS1994

Supersonic laminar flow control research

The objective of the research is to understand supersonic laminar flow stability, transition and active control. Some prediction techniques will be developed or modified to analyze laminar stability. The effects of supersonic laminar flow with distributed heating and cooling on active control will be studied. The primary tasks of the research applying to the NASA/Ames POC and LFSWT's nozzle design with laminar flow control are as follows: (1) supersonic laminar boundary layer stability and transition prediction; (2) effects of heating and cooling for supersonic laminar flow control; and (3) POC and LFSWT nozzle design with heating and cooling effects combining wall contour and length changes.

Lo, C. F.↗
NASA NTRS1992

NASA F-16XL supersonic laminar flow control program overview

The viewgraphs and discussion of the NASA supersonic laminar flow control program are provided. Successful application of laminar flow control to a High Speed Civil Transport (HSCT) offers significant benefits in reductions of take-off gross weight, mission fuel burn, cruise drag, structural temperatures, engine size, emissions, and sonic boom. The ultimate economic success of the proposed HSCT may depend on the successful adaption of laminar flow control, which offers the single most significant potential improvements in lift drag ratio (L/D) of all the aerodynamic technologies under consideration. The F-16XL Supersonic Laminar Flow Control (SLFC) Experiment was conceived based on the encouraging results of in-house and NASA supported industry studies to determine if laminar flow control is feasible for the HSCT. The primary objective is to achieve extensive laminar flow (50-60 percent chord) on a highly swept supersonic wing. Data obtained from the flight test will be used to validate existing Euler and Navier Stokes aerodynamic codes and transition prediction boundary layer stability codes. These validated codes and developed design methodology will be delivered to industry for their use in designing supersonic laminar flow control wings. Results from this experiment will establish preliminary suction system design criteria enabling industry to better size the suction system and develop improved estimates of system weight, fuel volume loss due to wing ducting, turbocompressor power requirements, etc. so that benefits and penalties can be more accurately assessed.

Fischer, Michael C.↗
NASA NTRS1987

Supersonic laminar flow development in a square duct

Supersonic laminar flow development in a constant-area square duct exhibits as one of its distinguishing features the formation of two contrarotating secondary flow vortices centered about the corner bisector. This phenomenon does not occur in unbounded corner flow. The secondary flow causes an outward bulging of total pressure contours in the vicinity of the corner bisector for wholly attached flow conditions.

Davis, D. O.↗
NASA NTRS1996

Supersonic Laminar Flow Control Research

The objective of this research is to understand supersonic laminar flow stability, transition and active control. Some prediction techniques will be developed or modified to analyze laminar flow stability. The effects of distributed heating and cooling as an active boundary layer control technique will be studied. The primary tasks of the research apply to the NASA/Ames PoC and LFSWT's nozzle design with laminar flow control and are listed as follows: Predictions of supersonic laminar boundary layer stability and transition; Effects of wall heating and cooling on supersonic laminar flow control on a flat plate; Performance evaluation of the PoC and LFSWT nozzle designs with wall heating and cooling applied at different locations and various lengths; Effects of a conducted-vs-pulse wall temperature distribution for the LFSWT; and Application of wall heating and/or cooling to laminar boundary layer and flow separation control of airfoils and investigation of related active control techniques.

Lo, Ching F.↗
NASA NTRS1995

Supersonic laminar flow control research

The objective of this research is to understand supersonic laminar flow stability, transition and active control. Some prediction techniques will be developed or modified to analyze laminar flow stability. The effects of distributed heating and cooling as an active boundary layer control technique will be studied. The primary tasks of the research apply to the NASA/Ames PoC and LFSWT's nozzle design with laminar flow control and are listed as follows: (1) predictions of supersonic laminar boundary layer stability and transition; (2) effects of wall heating and cooling on supersonic laminar flow control; (3) performance evaluation of the PoC and LFSWT nozzle designs with wall heating and cooling applied at different locations and various lengths; and (4) effects of a conducted -vs- pulse wall temperature distribution for the LFSWT.

Lo, Ching F.↗
NASA NTRS1990

Supersonic laminar flow control on commercial transports

This paper provides an overview of the status of supersonic laminar flow control. Existing research into the aerodynamic problems of subsonic and supersonic laminar flow control is first reviewed to provide a prospective for subsequent discussions of recent studies to evaluate the potential performance benefits of the application of laminar flow control to supersonic transports. A flight research program to provide a realistic assessment of the technical feasibility is then described.

Wagner, R. D.↗
NASA NTRS1992

Overview of supersonic laminar flow control research on the F-16XL ships 1 and 2

NASA is directing research to develop technology for a high-speed civil transport. Supersonic laminar flow control has been identified as a program element, since it offers significant drag-reduction benefits and is one of the more promising technologies for producing an economically viable aircraft design. NASA is using two prototype F-16XL aircraft to research supersonic laminar flow control. The F-16XL planform is similar to design planforms of high-speed civil transports. The planform makes the aircraft ideally suited for developing technology pertinent to high-speed transports. The supersonic laminar flow control research programs for both aircraft are described. Some general results of the ship-1 program demonstrate that significant laminar flow was obtained using laminar flow control on a highly swept wing at supersonic speeds.

Anderson, Bianca T.↗
NASA NTRS1992

Overview of supersonic laminar flow control research on the F-16XL ships 1 and 2

NASA is directing research to develop technology for a high-speed civil transport. Supersonic laminar flow control has been identified as a program element, since it offers significant drag-reduction benefits and is one of the more promising technologies for producing an economically viable aircraft design. NASA is using two prototype F-16XL aircraft to research supersonic laminar flow control. The F-16XL planform is similar to design planforms of high-speed civil transports. The planform makes the aircraft ideally suited for developing technology pertinent to high-speed transports. The supersonic laminar flow control research programs for both aircraft are described. Some general results of the ship-1 program demonstrate that significant laminar flow was obtained using laminar flow control on a highly swept wing at supersonic speeds.

Anderson, Bianca T.↗
NASA NTRS1999

F-16XL-2 Supersonic Laminar Flow Control Flight Test Experiment

The F-16XL-2 Supersonic Laminar Flow Control Flight Test Experiment was part of the NASA High-Speed Research Program. The goal of the experiment was to demonstrate extensive laminar flow, to validate computational fluid dynamics (CFD) codes and design methodology, and to establish laminar flow control design criteria. Topics include the flight test hardware and design, airplane modification, the pressure and suction distributions achieved, the laminar flow achieved, and the data analysis and code correlation.

Anders, Scott G.↗
NASA NTRS1972

Numerical solutions of the Navier-Stokes equations for the supersonic laminar flow over a two-dimensional compression corner

Numerical solutions have been obtained for the supersonic, laminar flow over a two-dimensional compression corner. These solutions were obtained as steady-state solutions to the unsteady Navier-Stokes equations using the finite difference method of Brailovskaya, which has second-order accuracy in the spatial coordinates. Good agreement was obtained between the computed results and wall pressure distributions measured experimentally for Mach numbers of 4 and 6.06, and respective Reynolds numbers, based on free-stream conditions and the distance from the leading edge to the corner. In those calculations, as well as in others, sufficient resolution was obtained to show the streamline pattern in the separation bubble. Upstream boundary conditions to the compression corner flow were provided by numerically solving the unsteady Navier-Stokes equations for the flat plate flow field, beginning at the leading edge. The compression corner flow field was enclosed by a computational boundary with the unknown boundary conditions supplied by extrapolation from internally computed points.

Carter, J. E.↗