Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface Modification and Coatings”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

The effect of bond coating surface modification on the performance of atmospheric plasma spray thermal barrier coatings

Asperities in atmospheric plasma sprayed (APS) CoNiCrAlY bond coatings were observed to rapidly form spinel-type oxides growing into the APS yttria-stabilized zirconia (YSZ) top coating during isothermal exposures. To minimize these transient oxides, bond coatings were either lightly or heavily modified to remove asperities, prior to top coating deposition. After a 100 h isothermal exposure at 1100 °C in dry air, modified regions formed a thin, Al-rich thermally grown oxide (TGO) scale while unmodified regions formed Cr- and Ni-rich transient oxide. However, in 1-h furnace cycle testing (FCT) at 1100 °C, the modified bond coatings showed a reduced average lifetime compared to the specimens with unmodified bond coatings. The benefit of asperities may be to geometrically inhibit crack propagation, but the volume of transient oxide formed may also densify the adjacent YSZ and further inhibit cracking.

36 MATERIALS SCIENCE↗

Effect of AlP coating on electrochemical properties of LiMn{sub 2}O{sub 4} cathode material for lithium ion battery

Highlights: • Modified LiMn{sub 2}O{sub 4} surface with AlP successfully. • AlP coating surface modification enhances the cycling stability of LiMn{sub 2}O{sub 4} at both room temperature and 60 °C. • AlP coating surface modification improves the rate capability of LiMn{sub 2}O{sub 4}. - Abstract: AlP-modified LiMn{sub 2}O{sub 4} has been synthesized via a simple chemical deposition method followed by high-temperature heating. The X-ray diffraction patterns, SEM images and Energy Dispersive Spectrometer show the successful surface coating of LiMn{sub 2}O{sub 4} by F-43 m crystal form AlP. AlP-modified LiMn{sub 2}O{sub 4} has a high discharge capacity of 125.7 mAh g{sup −1} with retention of 87% at a current density of 1C between 3.3 V and 4.3 V after 100 cycles at 60 °C, while bare LiMn{sub 2}O{sub 4} has more than 28% capacity loss. At 10 rates, the coated sample delivers capacity of 100 mAh g{sup −1}, which is much higher than bare LiMn{sub 2}O{sub 4}. Based on the EIS (electrochemical impedance spectroscopy) result, AlP coating can effectively inhibit the increase of the charge transfer resistance during charging and discharging cycles.

36 MATERIALS SCIENCE↗

Properties of coated and modified surfaces

The ability to create surface and near-surface properties distinct from the bulk properties of a material by means of coating or surface modification techniques is an important new field of development for engineering materials, encompassing ion implantation, plasma processing, reactive deposition methods, ion beam deposition and modification, molecular beam epitaxy, and fast quench thermal processing. Attention is given to specific areas of process control which illustrate (1) the use of process development to control material properties, (2) the importance of surface modification and coating to the tribology and ion-surface interactions of semiconductor film growth, and (3) recent findings in surface science which exemplify potential applications of ion-surface interactions that generate novel material qualities.

Mattox, D. M.↗

Novel Fouling-Reducing Coatings for Ultrafiltration, Nanofiltration, and Reverse Osmosis Membranes

Polymeric membranes could potentially be the most flexible and viable long-term strategy for treatment of produced water from oil and gas production. However, widespread use of membranes, including reverse osmosis (RO) membranes, for produced water purification is hindered due to fouling caused by the impurities present in the water. Fouling of RO membranes is likely caused by surface properties including roughness, hydrophilicity, and charge, so surface modification is the most widely considered approach to improve the fouling properties of current RO membranes. This project focuses on two main approaches to surface modification: coating and grafting. Hydrophilic coating and grafting materials based on poly(ethylene glycol) (PEG) are applied to commercial RO membranes manufactured by Dow FilmTec and GE. Crossflow filtration experiments are used to determine the fouling resistance of modified membranes, and compare their performance to that of unmodified commercial RO membranes. Grafting and coating are shown to be two alternative methods of producing modified membranes with improved fouling resistance.

02 PETROLEUM↗

Materials path toward improved energy efficiency for High Energy Physics accelerators

For nearly fifty years researchers working with particle accelerators have envisioned reducing their initial and operating costs by substituting the intermetallic compound Nb 3 Sn for Nb as the cavity interior surface. The goal has remained elusive, stymied especially by the fall of cavity quality factor (representing increasing energy consumption) with increasing gradient (the amount of accelerator need to reach an energy goal). While one research group reported making a few cavities free of the problem, no one has reported how this comes about or has reproduced the improvement. We believe that insufficient understanding is responsible. We report here findings of a detailed, systematic study of the formation of Nb 3 Sn coatings on Nb, relating structure and properties of the coating to the process parameters and substrate materials on the one hand, and RF surface impedance and SRF cavity performance on the other was carried out, focusing on the two step (nucleation – deposition) tin vapor diffusion process. Major outcomes are: The choice of initial surface preparation (BCP etc) has no discernable impact on any quality of the final coating; Though tin chloride serves as the coating nucleant, no trace could be found by any means of chlorine after nucleation or coating; No evidence was found for any substantive impact of the details of the nucleation on the ultimate coating, as long as it was done within the frequently used range; The coating forms as Nb 3 Sn crystals by tin from the vapor diffusing down grain boundaries to the Nb interface and growing there. Higher temperature and longer time lead to larger, but otherwise substantially identical crystals; All coatings exhibited roughness on the micron scale. Testing the effect of coating surface modification technologies in use by the community, only a carefully tailored electropolish showed significant benefit; and, Preliminary results indicate that Ti contamination may be associated with falling gradient. Two particular item appear promising for future work. The effect of surface topography in the range seen here on performance is significant for niobium. The nature and impact on Nb 3 Sn, if any, needs to be understood and managed. At what level Ti, Ta or other impurities affects the performance of Nb 3 Sn needs to be understood.

36 MATERIALS SCIENCE↗

Inexpensive net solar flux radiometer

Radiometer measures the absorption and reflection of solar radiation by opaque and translucent surfaces. Surface-coating modifications permit measurements over selected broad wavelength bands within the solar spectrum.

Darkow, G. L.↗

Analysis of the Effect of Surface Modification on Polyimide Composites Coated with Erosion Resistant Materials

The aim of this research is to enhance performance of composite coatings through modification of graphite-reinforced polyimide composite surfaces prior to metal bond coat/ hard topcoat application for use in the erosive and/or oxidative environments of advanced engines. Graphite reinforced polyimide composites, PMR-15 and PMR-II-50, formed by sheet molding and pre-pregging will be surface treated, overlaid with a bond coat and then coated with WC-Co. The surface treatment will include cleaning, RF plasma or ultraviolet light- ozone etching, and deposition of SiO(x) groups. These surface treatments will be studied in order to investigate and improve adhesion and oxidation resistance. The following panels were provided by NASA-Glenn Research Center(NASA-GRC): Eight compression molded PMR-II-50; 6 x 6 x 0.125 in. Two vacuum-bagged PMR-II-50; 12 x 12 x 0.125 in. Eight compression molded PMR-15; 6 x 6 x 0.125 in. One vacuum-bagged PMR-15; 12 x 12 x 0.125 in. All panels were made using a 12 x 12 in. T650-35 8HS (3K-tow) graphite fabric. A diamond-wafering blade, with deionized water as a cutting fluid, was used to cut PMR-II-50 and PMR-15 panels into 1 x 1 in. pieces for surface tests. The panel edges exhibiting delamination were used for the preliminary surface preparation tests as these would be unsuitable for strength and erosion testing. PMR-15 neat resin samples were also provided by NASA GRC. Surface profiles of the as-received samples were determined using a Dektak III Surface profile measuring system. Two samples of compression molded PMR-II-50 and PMR-15, vacuum-bagged PMR-II-50 and PMR-15 were randomly chosen for surface profile measurement according to ANSI/ASME B46.1. Prior to each measurement, the samples were blasted with compressed air to remove any artifacts. Five 10 mm-long scans were made on each sample. The short and long wavelength cutoff filter values were set at 100 and 1000 m, diamond stylus radius was 12.5 microns. Table 1 is a summary of the arithmetic average roughness (Ra) and waviness (Wa) for the composite surfaces.

Ndalama, Tchinga↗

Exploration of alloy surface and slurry modification to improve oxidation life of fused silicide coated niobium alloys

Edge and surface modifications of niobium alloys were investigated prior to coating with Si-20Cr-20Fe and slurry composition modification for performance in a 1370 C ambient pressure slow cycle test. The best coating obtained was Si-20Cr-20Mn with an average life of 63 cycles, compared to 40 for Si-20Cr-20Fe on FS-85 (100 percent improvement in weight parity life). Edge beading extended the lives of Si-20Cr-20Fe-coated Cb-752 and FS-85 to 57 and 41 cycles respectively (50 and 20 percent improvements in weight parity life respectively). W, Al2O3 and ZrO2(CaO) surface modifications altered coating crack frequency and microstructure and increased life somewhat.

Levine, S. R.↗

An improved oxygen reduction reaction activity and CO 2 -tolerance of La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ achieved by a surface modification with barium cobaltite coatings

Solid oxide fuel cells (SOFCs) cathode often suffers from the poisoning effect of the contaminants commonly encountered in air such as CO 2 . Here we report an effective approach to enhancing the activity and CO 2 tolerance of the state-of-the-art La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) cathode enabled by a coating of BaCoO 3-δ (BCO), as verified by the electrochemical testings, Raman analyses, and density functional theory calculations. When surface modified with a thin-film BCO coating, LSCF displays a much enhanced ORR activity and an improved durability against CO 2 . For example, anode supported SOFCs with the LSCF cathode coated with BCO coatings show a remarkable peak power density (Pmax) of 0.41 Wcm -2 and a significantly reduced degradation rate in current density of ~0.08% h -1 at 0.8 V and 700 °C for a period of 300 hs when humidified H2 (with 3 vol%H2O) was used as fuel and air with 8 vol% CO 2 as oxidant. The demonstrated performance is improved when compared with those of the cells with a blank LSCF electrode (a Pmax of ~0.36 Wcm -2 and a degradation rate of ~0.15% h -1 ) under the same conditions. Furthermore, the adsorption energy calculations suggests that BCO coating makes CO 2 adsorption much weaker than LSCF (-0.54 eV versus -1.07 eV).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Improved electrochemical and thermal performances of layered Li[Li 0.2 Ni 0.17 Co 0.07 Mn 0.56 ]O 2 via Li 2 ZrO 3 surface modification

We successfully coated a conductive Li 2 ZrO 3 layer on the surface of Li-rich layered cathode Li[Li 0.2 Ni 0.17 Co 0.07 Mn 0.56 ]O 2 in order to enhance its electrochemical performances. For the crystal structures, electrochemical properties and thermal stabilities of the bare and coated materials are studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), high resolution transmission electron microscopy (HRTEM), electron diffraction spectroscopy (EDS), inductively coupled plasma (ICP), galvanostatic cycling, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC). We found that the electrochemical performances of Li-rich cathode material are obviously improved by Li 2 ZrO 3 surface modification. Especially, the 1 wt.% Li 2 ZrO 3 -coated material demonstrates the best cycling performance, with capacity retention of 89% after 50 cycles, much better than that of the pristine one, 64%. Intensive explorations indicate that the improved electrochemical properties can be attributed to the Li 2 ZrO 3 surface layer, which not only stabilizes the cathode structure by decreasing the loss of oxygen, but also protects the Li-rich cathode material from side reaction(s) with the electrolyte and thus suppressing the fast growth of solid electrolyte interface (SEI) film on the surface of oxide particles.

25 ENERGY STORAGE↗

Exploration of alloy surface and slurry modification to improve oxidation life of fused silicide coated niobium alloys.

Edge and surface modification of niobium alloys prior to coating with Si-20Cr-20Fe and slurry composition modification were investigated to improve performance in a 1370 C, ambient pressure, slow-cycle test. The best coating obtained was Si-20Cr-20Mn with an average life of 63 cycles compared to 40 for Si-20Cr-20Fe on FS-85 (100 percent improvement in weight parity life). Edge beading extended the lives of Si-20Cr-20Fe coated Cb-752 and FS-85 to 57 and 41 cycles, respectively (50 and 20 percent improvements in weight parity life, respectively).

Levine, S. R.↗

Toward Lithium Recovery Using Modular (and Membraneless) Phase Separation and Extraction (MPSE) Technology with Ionic Liquid (IL) Solvents: Effect of Coatings

In this work, a single-channel slope-plate Modular and Membrane-less Phase Separation and Extraction (MPSE) device was fabricated using 3D printing. The slope-plate was designed with an insertable glass slide to enable surface modification with coatings. Self-assembled monolayers (SAMs) and perfluoropolyether (Zdol) coatings were applied to tailor surface wettability and enhance phase separation. Using a model biphasic system of water and hexadecane, both coatings significantly improved the separation efficiency compared to the uncoated device by promoting selective wetting. Building on these results, lithium extraction from a simulated saline solution was investigated using 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([EMIM][NTf₂]) as the ionic liquid (IL) extractant. The IL effectively extracted Li⁺ from the aqueous phase in bulk extraction, demonstrating its potential for lithium recovery. However, the low interfacial tension between the IL and aqueous phases posed challenges for phase separation. The application of SAM and Zdol coatings effectively mitigated this issue. Overall, integrating tailored surface chemistry with the slope-plate MPSE design shows great promise as an efficient and scalable platform for studying liquid–liquid separation and optimizing ionic liquid–based extraction processes for lithium recovery from saline sources.

3D printing↗

Reactor concepts for atomic layer deposition on agitated particles: A review

The number of possible applications for nanoparticles has strongly increased in the last decade. For many applications, nanoparticles with different surface and bulk properties are necessary. A popular surface modification technique is coating the particle surface with a nanometer thick layer. Atomic layer deposition (ALD) is known as a reliable method for depositing ultrathin and conformal coatings. In this article, agitation or fluidization of the particles is necessary for performing ALD on (nano)particles. The principles of gas fluidization of particles will be outlined, and a classification of the gas fluidization behavior of particles based on their size and density will be given. Following different reactor concepts that have been designed to conformally coat (nano)particles with ALD will be described, and a concise overview will be presented of the work that has been performed with each of them ending with a concept reactor for performing spatial ALD on fluidized particles.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Acid Etching‐Driven Self‐Assembly of Mn‐Shell Inducing Rock‐Salt Phase for Enhanced Single‐Crystal Ni‐Rich Cathodes

With the wide adoption of Li‐ion batteries, Ni‐rich cathode is considered as one of the most promising candidates of cathodes due to its high energy density and low cost. However, stability decreased with increasing Ni content in the Ni‐rich cathode. To solve this bottleneck, many strategies, such as coating, doping, surface modification, and special morphologies, have been developed. Herein, we introduce a groundbreaking approach for enhancing Ni‐rich cathode through an innovative acid etching process that promotes Mn shell self‐assembly, inducing a rock‐salt phase on the surface. This method not only simplifies the Ni‐rich cathode modification process, but also significantly improves the structural stability and electrochemical performance of Ni‐rich cathode. Our findings demonstrate that developed single‐crystal Ni‐rich cathode shows 3–34 % better stability compared to both commercial modified Ni‐rich cathode and unmodified counterparts. The unique Mn shell effectively mitigates reversible phase shifts during cycling, contributing to a remarkable enhancement in cycling stability. Additionally, this novel fabrication technique paves the way for cost‐effective production of high‐performance cathode materials, offering substantial benefits for lithium‐ion battery technology. And this study proves the potential of this method in advancing the design and development of durable, high‐capacity cathode materials for next‐generation batteries.

Ni-rich cathode↗

Advances in Electrospun Poly(ε-caprolactone)-Based Nanofibrous Scaffolds for Tissue Engineering

Tissue engineering has great potential for the restoration of damaged tissue due to injury or disease. During tissue development, scaffolds provide structural support for cell growth. To grow healthy tissue, the principal components of such scaffolds must be biocompatible and nontoxic. Poly(ε-caprolactone) (PCL) is a biopolymer that has been used as a key component of composite scaffolds for tissue engineering applications due to its mechanical strength and biodegradability. However, PCL alone can have low cell adherence and wettability. Blends of biomaterials can be incorporated to achieve synergistic scaffold properties for tissue engineering. Electrospun PCL-based scaffolds consist of single or blended-composition nanofibers and nanofibers with multi-layered internal architectures (i.e., core-shell nanofibers or multi-layered nanofibers). Nanofiber diameter, composition, and mechanical properties, biocompatibility, and drug-loading capacity are among the tunable properties of electrospun PCL-based scaffolds. Scaffold properties including wettability, mechanical strength, and biocompatibility have been further enhanced with scaffold layering, surface modification, and coating techniques. In this article, we review nanofibrous electrospun PCL-based scaffold fabrication and the applications of PCL-based scaffolds in tissue engineering as reported in the recent literature.

Polymer Science↗