Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface Passivation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Reducing Surface Recombination Velocity of Methylammonium-Free Mixed-Cation Mixed-Halide Perovskites via Surface Passivation

We control surface recombination in the mixed-cation, mixed-halide perovskite, FA0.83Cs0.17Pb(I0.85Br0.15)3, by passivating nonradiative defects with the polymerizable Lewis base (3-aminopropyl)trimethoxysilane (APTMS). We demonstrate average minority carrier lifetimes >4 µs, nearly single exponential monomolecular photoluminescence decays, and high external photoluminescence quantum efficiencies (>20%, corresponding to ~97% of the maximum theoretical quasi-Fermi-level splitting) at low excitation fluence. We confirm both the composition and valence band edge position of the FA0.83Cs0.17Pb(I0.85Br0.15)3 perovskite using multi-institutional, cross-validated, X-ray photoelectron spectroscopy and UV photoelectron spectroscopy measurements. We extend the APTMS surface passivation to higher bandgap double-cation (FA and Cs) compositions (1.7, 1.75, and 1.8 eV) as well as the widely used triple-cation (FA, MA, and Cs) composition. Finally, we demonstrate that the average surface recombination velocity decreases from ~1000 to ~10 cm/s post APTMS passivation for FA0.83Cs0.17Pb(I0.85Br0.15)3. Our results demonstrate that surface-mediated recombination is the primary nonradiative loss pathway in many methylammonium (MA)-free mixed-cation mixed-halide films with a range of different bandgaps, which is a problem observed for a wide range of perovskite active layers and reactive electrical contacts. Our study also provides insights to develop passivating molecules that help reduce surface recombination in MA-free mixed-cation mixed-halide films and indicates that surface passivation and contact engineering will enable near-theoretical device efficiencies with these materials.

14 SOLAR ENERGY↗
DOE OSTI2022

All-perovskite tandem solar cells with improved grain surface passivation

All-perovskite tandem solar cells hold the promise of surpassing the efficiency limits of single-junction solar cells; however, until now, the best-performing all-perovskite tandem solar cells have exhibited lower certified efficiency than have single-junction perovskite solar cells. A thick mixed Pb–Sn narrow-bandgap subcell is needed to achieve high photocurrent density in tandem solar cells, yet this is challenging owing to the short carrier diffusion length within Pb–Sn perovskites. Here we develop ammonium-cation-passivated Pb–Sn perovskites with long diffusion lengths, enabling subcells that have an absorber thickness of approximately 1.2 μm. Molecular dynamics simulations indicate that widely used phenethylammonium cations are only partially adsorbed on the surface defective sites at perovskite crystallization temperatures. The passivator adsorption is predicted to be enhanced using 4-trifluoromethyl-phenylammonium (CF3-PA), which exhibits a stronger perovskite surface-passivator interaction than does phenethylammonium. By adding a small amount of CF3-PA into the precursor solution, we increase the carrier diffusion length within Pb–Sn perovskites twofold, to over 5 μm, and increase the efficiency of Pb–Sn perovskite solar cells to over 22%. Here, we report a certified efficiency of 26.4% in all-perovskite tandem solar cells, which exceeds that of the best-performing single-junction perovskite solar cells. Encapsulated tandem devices retain more than 90% of their initial performance after 600 h of operation at the maximum power point under 1 Sun illumination in ambient conditions.

14 SOLAR ENERGY↗
DOE OSTI2024

Crystalline Si Surface Passivation with Nafion for Bulk Defects Detection with Electron Paramagnetic Resonance

Here, in monocrystalline Si (c-Si) solar cells, identification and mitigation of bulk defects are crucial to achieving a high photoconversion efficiency. To spectroscopically detect defects in the c-Si bulk, it is desirable to passivate the surface defects. Passivation of the c-Si surface with dielectrics such as Al 2 O 3 and SiNx requires deposition at elevated temperatures, which can influence defects in the bulk. Herein, we report on the passivation of different Czochralski (Cz) Si wafer surfaces by an organic copolymer, Nafion. We test the efficacy of the surface passivation at temperatures ranging from 6 to 473 K to detect bulk defects using electron paramagnetic resonance (EPR) spectroscopy. By comparing with state-of-the-art passivation layers, including Al 2 O 3 and liquid HF/HCl, we found that at room temperature, Nafion can provide comparable passivation of n-type Cz Si with an implied open-circuit voltage (iV oc ) of 713 mV and a recombination current prefactor J o of 5 fA/cm 2 . For p-type Cz Si, we obtained an iV oc of 682 mV with a J o of 22.4 fA/cm 2 . Scanning electron microscopy and photoluminescence reveal that Nafion can also be used to passivate the surface of c-Si solar cell fragments scribed from a solar cell module by using a laser. Consistent with previous studies, analysis of the EPR spectroscopy data confirms that the H-terminated surface is necessary, and fixed negative charge in Nafion is responsible for the field-effect passivation. While the surface passivation quality was maintained for almost 24 h, which is sufficient for spectroscopic measurements, the passivation degraded over longer durations, which can be attributed to surface SiO x growth. These results show that Nafion is a promising room-temperature surface passivation technique to study bulk defects in c-Si.

14 SOLAR ENERGY↗
DOE OSTI2021

Hydrogenation and C-S bond activation pathways in thiophene and tetrahydrothiophene reactions on sulfur-passivated surfaces of Ru, Pt, and Re nanoparticles

Thiophene-H2 reactions proceed via sulfur removal and hydrogenation routes on dispersed metal nanoparticles that become decorated by refractory S-adlayers during catalysis. The identity and kinetic relevance of the required elementary steps are described here based on rates measured at S-chemical potentials set by H2S/H2 ratios similar to those prevalent during practical catalysis on Re, ReSx, Ru, and Pt catalysts. Free energies for S adatom formation (from H2S decomposition and H2 evolution) are strongly exothermic (< -50 kJ mol-1 on Pt(111) and < -150 kJ mol-1 on Re and Ru(0001)), but strong repulsions between S adatoms cause adsorption free energies to increase significantly with coverage on all three surfaces, preventing complete monolayer formation. These adlayers, composed of unreactive S-atoms (S') that cover 1/3–2/3 ML leave residual interstitial spaces (*) that bind S-atoms (S*), intermediates, and transition states reversibly, as required for catalytic turnovers. The number and binding properties of these interstices depend on the identity and chemical state of the nanoparticle bulk phase, which influences S'-binding and coverages and cause large differences in direct desulfurization and hydrogenation turnover rates (per exposed metal atom) on dispersed Re, ReSx, Ru, and Pt. The identity and kinetic relevance of elementary steps for desulfurization (to C4¬ hydrocarbons) and hydrogenation (to tetrahydrothiophene; THT) are similar among these catalysts; they involve the kinetically-relevant formation of a thiophene-derived intermediate (monohydrothiophene on Re and ReSx; dihydrothiophene on Ru and Pt) that either cleaves its C-S bond or “over-hydrogenates” to THT in one surface sojourn. THT then undergoes C-S bond cleavage in secondary reactions that correct such over-hydrogenation to form the more unsaturated species that cleave C-S bonds. THT/C4 product ratios are insensitive to H2S/H2 ratios and thiophene pressure, even though active interstitial spaces are covered by kinetically-detectable coverages of S* and thiophene; therefore, primary and secondary reactions must involve the same active surfaces. The observed increase in THT/C4 ratios with H2 pressure shows that THT formation transition states involve a larger number of H-atoms than for C-S cleavage. The requirement for bound species with intermediate unsaturation (between THT and thiophene) for C-S bond cleavage is reminiscent of the H-shuttling required in C-C and C-O hydrogenolysis, reactions that involve the partial dehydrogenation of alkanes and alkanols, respectively, to weaken such bonds and to increase the formation entropy of the relevant transition states via the evolution of H2(g). These mechanistic details challenge prevalent paradigms about different site requirements for hydrogenation and desulfurization pathways and about how metal-sulfur bond energies act as descriptors of reactivity; in fact, such binding energies merely act to define the refractory S-adlayers that enable the formation of weakly-binding interstices that reversibly bind intermediates and transition states, thus allowing catalytic turnovers.

Yik, Edwin↗
NASA NTRS1989

A new structure for comparing surface passivation materials of GaAs solar cells

The surface recombination velocity (S sub rec) for bare GaAs is typically as high as 10 to the 6th power to 10 to the 7th power cm/sec, which dramatically lowers the efficiency of GaAs solar cells. Early attempts to circumvent this problem by making an ultra thin junction (xj less than .1 micron) proved unsuccessful when compared to lowering S sub rec by surface passivation. Present day GaAs solar cells use an GaAlAs window layer to passivate the top surface. The advantages of GaAlAs in surface passivation are its high bandgap energy and lattice matching to GaAs. Although GaAlAs is successful in reducing the surface recombination velocity, it has other inherent problems of chemical instability (Al readily oxidizes) and ohmic contact formation. The search for new, more stable window layer materials requires a means to compare their surface passivation ability. Therefore, a device structure is needed to easily test the performance of different passivating candidates. Such a test device is described.

Desalvo, Gregory C.↗
DOE OSTI2025

Detector Performance on Surface Passivation and its Long-Term Stability

Surface passivation is an ideal technique to prepare the surfaces of fabrication Cadmium Zinc Telluride (CZT) and related semiconductor devices such as Cadmium Zinc Tellurium Selenide (CZTS). Surface passivation techniques reduce the effects of aging in the detector [1]. Surface performance effects on material performance can result in fluctuations in energy resolution over time (such as periods of a year or more). The long-term stability of surface passivation with Potassium Hydroxide (KOH) was observed with measurement of 1) current (nano Amp) vs voltage (V) and 2) spectral response and energy resolution throughout the years. Three CZTS detector samples of M2, M3, and M4 were examined using a photomultiplier tube and voltage amplifier. The Bridgman technique is used to grow the CZTS used in this study.

Johnson, Kirsten [Morgan State Univ., Baltimore, M↗
DOE OSTI2022

(3-Aminopropyl)trimethoxysilane Surface Passivation Improves Perovskite Solar Cell Performance by Reducing Surface Recombination Velocity

We demonstrate reduced surface recombination velocity (SRV) and enhanced power-conversion efficiency (PCE) in mixed-cation mixed-halide perovskite solar cells by using (3-aminopropyl)trimethoxysilane (APTMS) as a surface passivator. We show the APTMS serves to passivate defects at the perovskite surface, while also decoupling the perovskite from detrimental interactions at the C 60 interface. We measure a SRV of ~125 ± 14 cm/s, and a concomitant increase of ~100 meV in quasi-Fermi level splitting in passivated devices compared to the controls. We use time-resolved photoluminescence and excitation-correlation photoluminescence spectroscopy to show that APTMS passivation effectively suppresses non-radiative recombination. We show that APTMS improves both the fill factor and open-circuit voltage (V OC ), increasing V OC from 1.03 V for control devices to 1.09 V for APTMS-passivated devices, and leads to a PCE increase from 15.90% to 18.03%. Here, we attribute the enhanced performance to reduced defect density resulting in suppressed nonradiative recombination and lower SRV at the perovskite/transport layer interface.

14 SOLAR ENERGY↗
DOE OSTI2023

Atomistic mechanisms of water vapor–induced surface passivation

The microscopic mechanisms underpinning the spontaneous surface passivation of metals from ubiquitous water have remained largely elusive. Here, using in situ environmental electron microscopy to atomically monitor the reaction dynamics between aluminum surfaces and water vapor, we provide direct experimental evidence that the surface passivation results in a bilayer oxide film consisting of a crystalline-like Al(OH) 3 top layer and an inner layer of amorphous Al 2 O 3 . The Al(OH) 3 layer maintains a constant thickness of ~5.0 Å, while the inner Al 2 O 3 layer grows at the Al 2 O 3 /Al interface to a limiting thickness. On the basis of experimental data and atomistic modeling, we show the tunability of the dissociation pathways of H 2 O molecules with the Al, Al 2 O 3 , and Al(OH) 3 surface terminations. The fundamental insights may have practical significance for the design of materials and reactions for two seemingly disparate but fundamentally related disciplines of surface passivation and catalytic H 2 production from water.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Degradation and Accelerated Recovery of Surface Passivation in n+, p+, and Intrinsic Poly-Si/SiOx Passivating Contacts for Silicon Solar Cells

We report on the degradation and recovery of surface passivation of fired poly-Si/SiOx passivating contacts with hydrogen containing Al2O3 during annealing in the dark and under illumination. Upon firing to a peak temperature of 670 degrees C, the iVoc for symmetric test structures with n+, p+, and intrinsic poly-Si/SiOx contacts decreases due to a loss of surface passivation. Upon further annealing over the temperature range of 200-350 degrees C in the dark, depending on the type of doping, the surface passivation either shows further degradation followed by recovery, or direct recovery to the initial iVoc. Annealing at higher temperatures and/or higher illumination intensities accelerates the kinetics for both degradation and recovery processes. We show that the degradation and recovery processes are thermally activated and proceed identically in subsequent firing and annealing steps showing their cyclic nature. We present a series reaction model to explain the kinetics of degradation and recovery processes for n+ and intrinsic poly-Si/SiOx contacts. By fitting the model's rate expressions to the data, the determined effective activation energy barriers for degradation and recovery for n+ poly-Si/SiOx contacts in the dark are 1.24 and 1.51 eV, which are lowered under 7.5 Suns illumination to 0.76 and 1.15 eV, respectively.

14 SOLAR ENERGY↗
DOE OSTI2021

Self-assembled multifunctional nanostructures for surface passivation and photon management in silicon photovoltaics

This work reports the fabrication and characterization of multifunctional, nanostructured passivation layers formed using a self-assembly process that provide both surface passivation and improved light trapping in crystalline silicon photovoltaic (PV) cells. Scalable block copolymer self-assembly and vapor phase infiltration processes are used to form arrays of aluminum oxide nanostructures (Al 2 O 3 ) on crystalline silicon without substrate etching. The Al 2 O 3 nanostructures are characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and spectroscopic ellipsometry. Injection-level dependent photoconductance measurements are used to determine the effective carrier lifetime of the samples to confirm the nanostructures successfully passivate the Si surface. Finite element method simulations and reflectance measurement show that the nanostructures increase the internal rear reflectance of the PV cell by suppressing the parasitic optical losses in the metal contact. An optimized morphology of the structures is identified for their potential use in PV cells as multifunctional materials providing surface passivation, photon management, and carrier transport pathways.

14 SOLAR ENERGY↗
DOE OSTI2022

Novel and effective surface passivation for high efficiency n- and p-type Silicon solar cell

The project objective was to develop a novel Si surface passivation method using chalcogens, sulfur (S) and/or selenium (Se), as passivating elements, to withstand industry-standard high temperature contacting and metallization schemes for p-type Si based passivated emitter and rear contact (p-PERC) solar cells. The back surface passivation of PERC cells has been improved drastically with the invention and successful application of an Al 2 O 3 passivation layer. However, the front n + diffused junction surface is still poorly passivated by the standard amorphous silicon nitride (SiNx) anti-reflection coating (ARC) layer. This project sought to address the passivation challenges of both front n+ emitter and undiffused p-Si back surface. Improved p-PERC solar cell performance with open circuit voltage (V OC ) > 680 mV and efficiency of 22% were targeted to validate superior defect passivation properties as compared to standard SiO 2 / Al 2 O 3 passivation. During this project, we systematically investigated process-structure-properties-performance relationships of this novel advanced defect passivation approach. The S/Se passivation was carried out by reacting industrial Czochralski (Cz) Si wafers in H 2 S and H 2 Se gases in a chemical vapor deposition (CVD) reactor at temperatures up to 700°C. After an exhaustive optimization of the process parameters (temperature, time, and gas concentration), we established an optimized process and demonstrated extremely low surface recombination velocities (SRVs) of 1.5 cm/s and 8 cm/s on n-type and p-type Si, respectively, by S-passivation. In-depth surface and interface characterization were performed using soft x-ray and photoelectron spectroscopies (XPS, UPS, XES), combined with capacitance-voltage-frequency (C-V-f) measurements, to decipher the surface chemical/electronic structure and interface defect state densities. These measurements provided critical understanding of the defect passivation mechanism and elucidated the presence of surface S-Si bonds, a reduction of surface dipoles, and low interface state densities (D it ) < 10 11 cm -2 ev -1 . We also found that the Se-passivation is inferior to the S-passivation (by at least one order of magnitude in SRV). Application of the optimized S-passivation to the n+ diffused emitter surface led to a low surface recombination current density, J0 ≈ 40 fA/cm 2 (~ 1/4 of the industry-standard SiNx-passivation), and high implied V OC (686 mV) in p-PERC solar cell structures. The S-passivation process also was found to improve the bulk quality of the p-type Si, better than the SiO 2 or Al 2 O 3 passivation processes. After successful demonstration of efficient passivation of Si surface defects by S, we extensively studied the air, thermal, and illumination stability of the passivation structure. S-passivation itself degrades in air due to competing reactions with moisture and oxygen to form oxides, which can be eliminated by a SiNx capping layer (also acting as a anti-reflective coating). After SiNx process optimization, we demonstrated illumination and thermally stable S-passivation with SRV < 5 cm/s and J 0 < 80 fA/cm 2 . These enhancements in Si passivation, incorporated into p-PERC cells, achieved an efficiency of 19.93% with V OC = 649 mV, using manufacturing metallization and contacting schemes. The low cell performance (cell V OC is much less than the implied V OC = 686 mV, anticipated from surface passivation) was identified due to degradation of S-passivation during the metal firing step (out-diffusion of S from the Si interface to the SiNx surface). The S-passivation of Si surfaces shows significant promise with excellent passivation quality, essential for high performance (high V OC , high efficiency) solar cells. Integration of this innovative defect passivation into devices, however, demands further development of the capping layer, low temperature (<700°C) metallization process, and/or engineering of advanced device structures. Surface passivation-dominated advanced Si solar cells, such as tunnel oxide passivated contacts and Si heterojunctions, are increasingly of interest due to their high-performance potential and will have a growing photovoltaic market share in the near future.

14 SOLAR ENERGY↗
NASA NTRS1984

Investigation of silicon surface passivation by silicon nitride film deposition

The use of Sin sub x grown by plasma enhanced chemical vapor deposition (PECVO) for passivating silicon surfaces was studied. The application of PECVO SiN sub x films for passivations of silicon N+/P or P+/N solar cells is of particular interest. This program has involved the following areas of investigation: (1) Establishment of PECVO system and development of procedures for growth of SiN sub x; (2) Optical characterization of SiN sub x films; (3) Characterization of the SiN sub x/Si interface; (4) Surface recombination velocity deduced from photoresponse; (5) Current-Voltage analyses of silicon N+/P cells; and (6) Gated diode device studies.

Olsen, L. C.↗
DOE OSTI2024

Surface Passivation to Improve the Performance of Perovskite Solar Cells

Perovskite solar cells (PSCs) suffer from a quick efficiency drop after fabrication, partly due to surface defects, and efficiency can be further enhanced with the passivation of surface defects. Herein, surface passivation is reviewed as a method to improve both the stability and efficiency of PSCs, with an emphasis on the chemical mechanism of surface passivation. Various molecules are utilized as surface passivants, such as halides, Lewis acids and bases, amines (some result in low-dimensional perovskite), and polymers. Multifunctional molecules are a promising group of passivants, as they are capable of passivating multiple defects with various functional groups. This review categorizes these passivants, in addition to considering the potential and limitations of each type of passivant. Additionally, surface passivants for Sn-based PSCs are discussed since this group of PSCs has poor photovoltaic performance compared to their lead-based counterpart due to their severe surface defects. Lastly, future perspectives on the usage of surface passivation as a method to improve the photovoltaic performance of PSCs are addressed to provide a direction for upcoming research and practical applications.

14 SOLAR ENERGY↗
DOE OSTI2022

Enhanced Surface Passivation by Atomic Layer Deposited Al 2 O 3 for Ultraviolet Sensitive Silicon Photomultipliers

Here, we describe a superior passivation of p-type (p + ) Si surface by Al 2 O 3 thin film that is synthesized by plasma-assisted atomic layer deposition for ultraviolet sensitive silicon photomultipliers (SiPM), compared to conventional SiO 2 and SiN x passivation schemes. The superiority of Al 2 O 3 passivation is due to not only a sufficiently low interface defect density but also a high density of built-in negative charges. A 7 nm thin Al 2 O 3 film can yield an emitter saturation current density of ~8 fA/cm 2 on high sheet resistance p + layer, compared to ~60 and ~1480 fA/cm 2 for thermal SiO 2 and SiN x passivation. This superior surface passivation allows the photon-generated carriers to have higher probabilities to reach the high-field region to trigger an avalanche event. In addition, Al 2 O 3 thin film provides very low values of effective surface recombination velocity on low resistivity n-type and p-type Si surfaces, which can lead to well-passivated surface features on guard ring and trench isolation regions of SiPM. These demonstrate the potential of Al 2 O 3 thin film passivation to improve quantum efficiency and thus photo-detection efficiency of ultraviolet sensitive SiPM with p + /n - /n/n + structure.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Back-Surface Passivation of CdTe Solar Cells Using Solution-Processed Oxidized Aluminum

Although back-surface passivation plays an important role in high-efficiency photovoltaics, it has not yet been definitively demonstrated for CdTe. Here, we present a solution-based process, which achieves passivation and improved electrical performance when very small amounts of oxidized Al 3+ species are deposited at the back surface of CdTe devices. The open circuit voltage (V oc ) is increased and the fill factor (FF) and photoconversion efficiency (PCE) are optimized when the total amount added corresponds to ~1 monolayer, suggesting that the passivation is surface specific. Addition of further Al 3+ species, present in a sparse alumina-like layer, causes the FF and PCE to drop as the interface layer becomes blocking to current flow. The optimized deposit increases the average baseline PCE for both Cu-free devices and devices where Cu is present as a dopant. The greatest improvement is found when the Al 3+ species are deposited prior to the CdCl 2 activation step and Cu is employed. In this case, the best-cell efficiency was improved from 12.6 to 14.4%. Furthermore, time-resolved photoluminescence measurements at the back surface and quantum efficiency measurements performed at the maximum power point indicate that the performance enhancement is due to a reduction in the interface recombination current at the back surface.

14 SOLAR ENERGY↗
DOE OSTI2021

Dopant diffused Si surface passivation by H 2 S gas reaction and quinhydrone-methanol treatment

Phosphorus (n + ) and boron (p + ) diffused n-type textured Cz Si wafers are passivated by two different methods: gas phase H 2 S reaction and quinhydrone-methanol (QH-MeOH) solution. The dopant diffused surface passivation quality, quantified by saturation current density (J 0 ), strongly depends on the diffusion type and the passivation method. H 2 S reaction at 550ºC passivates n + diffused surface as good as state-of-the-art Si oxide/silicon nitride stack (SiO 2 /SiN X ), while QH-MeOH passivates p + diffused surface to the same level as state-of-the-art atomic layer deposited aluminum oxide / silicon nitride stack (Al 2 O 3 /SiN X ).

Das, Ujjwal↗
NASA NTRS1984

Silicon surface passivation by silicon nitride deposition

Silicon nitride deposition was studied as a method of passivation for silicon solar cell surfaces. The following three objectives were the thrust of the research: (1) the use of pecvd silicon nitride for passivation of silicon surfaces; (2) measurement techniques for surface recombination velocity; and (3) the importance of surface passivation to high efficiency solar cells.

Olsen, L. C.↗
NASA NTRS1988

Sulfur as a surface passivation for InP

The use of liquid and gas phase sulfur pretreatment of the surface of InP as a way to form a near-ideal passivated surface prior to chemical vapor deposition of SiO2 was investigated. Results of high-frequency and quasi-static capacitance-voltage measurements, as well as enhancement mode insulated gate field-effect transistor (FET) transductance and drain current stability studies, all support the efficacy of this approach for metal-insulator-semiconductor application of this semiconductor. In particular, surface state values in the range of 10 to the 10th to a few 10 to the 11th/sq cm per eV and enhancement mode FET drain current drifts of less than 5 percent over a 12 h test period were measured.

Iyer, R.↗