Search NASA⌕ Search

SEARCH · Search NASA

Results for “TANTALUM ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Post-irradiation examination of commercial tantalum alloys following neutron irradiation

Post irradiation examination of two commercial tantalum alloys (based on Ta-8 %W) revealed significant irradiation hardening following neutron irradiation in the High Flux Isotope Reactor at Oak Ridge National Laboratory. Tensile samples of commercial Ta alloys T-111 and ASTAR-811C were irradiated to a total neutron fluence (E > 0.1 MeV) in the range (2–4)x10 21 n/cm 2 (0.39–0.75 dpa) at an irradiation temperature near 900 °C. Tensile testing conducted at room temperature and at 800 °C revealed significant irradiation hardening under all test conditions. Samples that were tensile tested at room temperature exhibited brittle failure, whereas ductility was maintained for elevated temperature testing. The irradiation hardening and embrittlement noted for both alloys was attributed to irradiation-induced dislocation loop formation as confirmed through scanning transmission electron microscopy analysis. Corresponding energy dispersive x-ray spectroscopy revealed radiation-induced segregation of Hf in these loop populations. This Hf enrichment is shown to result in eventual co-precipitation of elongated (Hf,O)-rich precipitates along the dislocation loops. Further, these results show that irradiation hardening is enhanced via irradiation-enhanced precipitation at elevated irradiation temperatures. Consequently, the minimum recommended operating temperature window for Ta alloys should be increased to account for observed hardening/embrittlement at irradiation temperatures as high as 900 °C (1,173 K).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Gold-tantalum alloy films deposited by high-density-plasma magnetron sputtering

Gold-tantalum alloy films are of interest for biomedical and magnetically-assisted inertial confinement fusion applications. Here, we systematically study the effects of substrate tilt (0°–80°) and negative substrate bias (0–100 V) on properties of ≲3-μm-thick films deposited by high-power impulse magnetron sputtering (HiPIMS) from a Au–Ta alloy target (with 80 at. % of Ta). Results reveal that, for all the substrate bias values studied, an increase in substrate tilt leads to a monotonic decrease in film thickness, density, residual compressive stress, and electrical conductivity. Larger substrate bias favors the formation of a body-centered cubic phase, with films exhibiting lower column tilt and higher density, electrical conductivity, and residual compressive stress. Furthermore, these changes are attributed to metal atom ionization effects, based on the lack of correlation with distributions of landing energies and incident angles of depositing species as calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. By varying substrate tilt and bias in HiPIMS deposition, properties of Au–Ta alloy films can be controlled in a very wide range, including residual stress from –2 to +0.5 GPa, density from 12 to 17 g/cm 3 , and the electrical resistivity from 50 to 4500 μΩ cm, enabling optimum deposition conditions to be selected for specific applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Tantalum alloy–based resonators for quantum information systems

Utilizing tantalum (Ta) in superconducting circuits has led to significant improvements, such as high qubit lifetime (T 1 ) and quality factors in both qubits and resonators, suggesting that material optimization plays an important role in the development of superconducting circuits. Thus we here explore superconducting gap engineering in Ta-based devices as a powerful strategy for expanding the range of suitable host materials. By alloying 20 atomic percent (at.%) hafnium into Ta thin films, we achieve a superconducting transition temperature (T c ) of 6.09 K as observed in direct current (DC) transport measurements, reflecting an increase in the superconducting gap. We systematically vary deposition conditions to control film orientation and transport properties of Ta-Hf alloy thin films. We then confirm the enhancement in T c via microwave measurements at millikelvin temperatures. We verify the ~40 increase in T c relative to bare Ta devices, while the loss contributions from two-level systems and quasi-particles remain unchanged in the low temperature regime. These findings emphasize the promise of material engineering in superconducting circuits and point to many potential material candidates for further exploration.

Ta-Hf alloy thin films↗
DOE OSTI2020

Microstructural stability of tantalum-alloyed ferritic-martensitic steel with neutron irradiation to 7.4 dpa at ~490 °C

Specimens of a reduced-activation ferritic-martensitic steel, called CNA1, were irradiated to 7.4 displacements per atom at ~490 °C in the High Flux Isotope Reactor. Vickers hardness and tensile properties revealed consistent softening that is attributed to some recovery during irradiation, with reduced laths and dislocation density. Detailed microstructural characterization by transmission electron microscopy and energy dispersive x-ray spectroscopy showed radiation-induced dislocation loops, few cavities, and slight dissolution of M 23 C 6 and MX precipitates. Partial amorphization was only observed in M 23 C 6 precipitated in matrix. Transmutation somewhat destabilized M 23 C 6 and MX, with a stronger effect on the later one by noticeable depletion of Ta with enriched W, which is consistent with the transmutation calculations. The microstructural evolution and associated strength changes were discussed with the assistance of computational thermodynamics.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructurally-Inspired Strategies to Print Tantalum and Tantalum-Tungsten Alloys

The goal of this project is to investigate strategies to print tantalum and tantalum- tungsten alloys, which are notoriously difficult to print with consistent results because of the sensitivity of the properties to small concentrations of interstitial impurities (particularly oxygen) and microstructure, and hence to processing conditions. The ultimate tensile stress (UTS) for non-additively manufactured Ta as a function of temperature shows a stunning variation. In direct metal laser sintering (DMLS) Ta, a strong dependence of porosity, grain morphology and texture on processing conditions was found.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructurally-Inspired Strategies to Print Tantalum and Tantalum-Tungsten Alloys

The goal of this project is to investigate strategies to print tantalum and tantalumtungsten alloys, which are notoriously difficult to print with consistent results because of the sensitivity of the properties to small concentrations of interstitial impurities (particularly oxygen) and microstructure, and hence to processing conditions. In direct metal laser sintering (DMLS) Ta, a strong dependence of porosity, grain morphology and texture on processing conditions was found.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Quasi-static to Dynamic Mechanical Response and Microstructure Development of Tantalum-Tungsten Alloys

Lawrence Livermore National Laboratory (LLNL) is interested the quasi-static to dynamic mechanical response and microstructure evolution of tantalum-tungsten (Ta-W) alloys (Ta-2.5W, Ta-5W, and Ta-10W, wt.%) made by conventional wrought processing and additive manufacturing (AM). This work scope was performed at the Colorado School of Mines (Mines) and included quasi-static (e.g., 10 -3 s -1 ) mechanical testing in tension and compression, along with selected high strain rate (Kolsky) pressure bar testing in compression (e.g., 10 3 s -1 ), with and without temperature variations in some instances. Complementary microstructure characterization was performed on undeformed and deformed samples to understand the role of processing on microstructural evolution and the deformation mechanisms that impact the mechanical response with variations in strain rate, temperature, and strain state (e.g., tension versus compression in selected examples). The wrought material provided by LLNL from Viridis Materials was found to have unrecrystallized regions within the microstructure, which led to unexpected results relative to previously reported properties for Ta-W. The AM Ta-2.5W (wt.%) material provided by LLNL was found to have higher compressive strength than wrought Ta-2.5W (wt.%), which is hypothesized to be due to differences in the crystallographic texture between the two materials. This project partially supported several postdocs and graduate students at Mines.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quasi-static to Dynamic Response and Microstructure Development of Tantalum-Tungsten Alloys

Lawrence Livermore National Laboratory (LLNL) has a need to understand the quasi-static to dynamic mechanical response and microstructure evolution of tantalum-tungsten (Ta-W) alloys made by conventional wrought processing and additive manufacturing (AM). This two-year work scope will be performed at the Colorado School of Mines (Mines) and will include quasi-static (e.g., 10 -3 s -1 ) mechanical testing in tension and compression, along with high strain rate (Kolsky) pressure bar testing in tension and compression (e.g., 10 3 s -1 ), without and with temperature variations. Gas gun experiments at higher strain rates (e.g., over 10 3 s -1 ) will also be pursued. Complementary microstructure characterization will be performed on undeformed and deformed samples to fundamentally understand the role of processing on the microstructure characteristics and resulting deformation mechanisms that dictate the mechanical response of these alloys with variations in strain rate, temperature, and strain state. Alloys of interest will be Ta-based, containing up to 10 wt.% W. LLNL will supply initial wrought-processed material for sample machining. LLNL will also supply samples built by AM during the project for testing. Arc melting and casting may also be performed at Mines to produce small quantities of different alloys for machining and exploratory testing on an as-needed basis. This project will support multiple postdocs and graduate students at Mines, training them with the knowledge, skills, and abilities needed to study materials under extreme conditions of interest to the National Nuclear Security Agency.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Sputter deposition of high electrical resistivity Au-Ta alloy coatings on rotating substrates

Sputter deposition of gold-tantalum alloy coatings is a key process for manufacturing hohlraums for magnetically-assisted inertial confinement fusion implosions. In this report we describe direct current magnetron sputter deposition of ~ 10 - μ~ 10 - μm-thick films of Au-80 at.% Ta onto rotating sphero-cylindrical hohlraum and planar Si witness substrates. Emphasis is given to how film microstructure and properties are affected by main deposition parameters, including argon working gas pressure, substrate bias, and the source composition (a single alloyed target compared to co-sputtering from two elemental targets). Experimental findings are correlated with distributions of landing energies and incident angles of depositing species calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Deposition conditions characterized by low energetics of depositing species favor the formation of a β-Ta-like phase. Implications of these results to hohlraum fabrication are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

IHS-60 Stored Energy Analysis

The IHS-60 consists of a General Purpose Heat Source (GPHS) Fueled Clad (FC) that has been hot isostatically pressed to eliminate the gap between the iridium clad and the fuel pellet, thus preventing differential motion between the pellet and the clad in shock and vibration environments. The vented FC is enclosed within a Molybdenum barrier comprising the liner body and the lower support member. The slip- t Molybdenum liner members serve as a mechanical barrier to plutonia contact of the tantalum alloy (T-111) strength member in the event the iridium clad should fail. The slip- t liner is not a barrier to gaseous transport, so a tantalum getter is installed near the vent region of the FC to preclude potential oxygen transport to the T-111 interior surface. The T-111 strength member encloses the Molybdenum liner assembly and provides for both helium gas retention and isotope fuel containment under impact and external pressure environments. It is surrounded by an outer clad of Hastelloy-S which protects the strength member from external oxidation and corrosive sources during nominal operation and in the event of off-nominal operation or accidents. Both the strength member and outer clad parts are closed with seal welds. The strength member and outer clad are the primary containment members of the 60-Watt IHS. The iridium clad contains the fuel pellet during nominal operation and mild accident environments, but it is not considered to be a primary containment member.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Dual-scale folding in cutting of commercially pure aluminum alloys

We examine a, hitherto, little-studied and curious machining chip morphology, with tell-tale signs of folding at two different length scales, that is common in cutting of certain ductile and highly strain-hardening metals like soft aluminum alloys, tantalum and niobium. This chip morphology does not appear in the usual catalogues of common chip types. The mechanics of formation of the “dual-scale folded chip” is studied in model material systems of commercially pure aluminum alloys (AA 1100 and AA 8040), that prominently exhibit this chip morphology. The flow, folding and associated plastic instabilities are investigated using micro/macro structure observations of the chip in a plane-strain cutting framework, with high-speed in situ imaging and image analysis of material flow; and force measurements. The smaller-scale folding is shown to develop in the primary deformation zone while the larger-scale folding occurs as the chip traverses the rake face of the tool. The resulting chip is composed of irregularly-spaced large folds, superimposed onto which are the quasi periodic small folds. The representative wavelengths of the two folds differ on average by an order of magnitude, 0.1 mm vs. 2 mm. The observations reveal a direct coupling between the material flow and chip morphology, and how specific attributes of the dual-scale folded chip arise from the flow mechanism. Plastic buckling is found to play a key role in the folding at both length scales. The small-scale folds are characteristic of a sinuous plastic flow mode, while the large-scale folding is characterized by buckling and stick-slip along the tool rake face, triggered by adhesive pinning of the chip to the tool. Important consequences of the dualscale folding are very large cutting forces, and force oscillations of large amplitude, despite the alloys being very soft, only ~ 25 HV. Here, the dual-scale folding is why many of these alloys are classified as “gummy” to machine. Since the dual-scale folded chip is associated with large cutting forces and poor surface quality, there is much to be gained by disrupting this flow type in practical machining applications. Methods for controlling the folding to improve machining performance with the gummy alloys are briefly discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Origin of age softening in the refractory high-entropy alloys

Refractory high-entropy alloys (RHEAs) are emerging materials with potential for use under extreme conditions. As a newly developed material system, a comprehensive understanding of their long-term stability under potential service temperatures remains to be established. This study examined a titanium-vanadium-niobium-tantalum alloy, a promising RHEA known for its superior high-temperature strength and room-temperature ductility. Using a combination of advanced analytical microscopies, Calculation of Phase Diagrams (CALPHAD) software, and nanoindentation, we investigated the evolution of its microstructure and mechanical properties upon aging at 700°C. Trace interstitials such as oxygen and nitrogen, initially contributing to solid solution strengthening, promote phase segregation during thermal aging. As a result of the depletion of solute interstitials within the metal matrix, a progressive softening is observed in the alloy as a function of aging time. This study, therefore, underscores the need for a better control of impurities in future development and application of RHEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of substrate tilt on sputter-deposited AuTa films

Gold-tantalum alloy films are of interest for biomedical and magnetically-assisted inertial confinement fusion applications. However, growth mechanisms of such Au-Ta alloy films are not well understood. Here, we systematically study the effect of substrate tilt on properties of films deposited by direct current magnetron sputtering from a AuTa alloy target. Experimental data is correlated with distributions of landing energies and incident angles of sputtered and backscattered species calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Results reveal that the deposition rate and film density monotonically decrease with increasing substrate tilt. Properties are similar for films with a tilt of 40° and below: films are amorphous, with an average compressive stress of 0.5 GPa, a density of 16 g/cm 3 , and electrical resistivity of 200 μΩ cm. The critical substrate tilt angle for the onset of porosity, a transition to a reduced stress state, and an increase in electrical resistivity lies between 40 and 60°. Based on Monte Carlo simulations, these changes in film properties are correlated with an increase in the average impact angle of the ballistic component of atomic flux. Implications of these results to deposition onto non-planar substrates are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development of New Magnetron Sputter Deposition Processes for Laser Target Fabrication

Magnetron sputter deposition is an enabling technology for laser target fabrication. Solutions are readily available for the deposition of most sub-micron-thick elemental films on planar substrates. However, major challenges still remain for the development of robust deposition processes in regimes of ultrathick (over ~10 μm) coatings and nonplanar substrates. These challenging deposition regimes are directly relevant to laser target applications, including both sphero-cylindrical hohlraums and spherical ablators for inertial confinement fusion (ICF) targets. Understanding underlying physical mechanisms for a specific material system is crucial for process development, given the overall complexity of the deposition process, its nonlinear dependence on deposition parameters, and a very large process space, often precluding conventional process optimization approaches. Here, we describe our approach to developing new deposition processes and give practical advice with examples of new results from our ongoing studies of glassy boron carbide ceramics for next-generation ICF ablators and nonequilibrium gold-tantalum alloys for hohlraums for magnetized ICF schemes. Emphasis is given to two major challenges of ultrathick coatings related to achieving process stability and reducing residual stress.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Sputtered Au–Ta films with tunable electrical resistivity

Gold–tantalum alloy films are attractive for hohlraums used in indirect drive magnetized inertial confinement fusion. A high electrical resistivity of over ~100 µΩ cm at cryogenic temperatures is an essential requirement for allowing an externally imposed pulsed magnetic field to soak through a hohlraum and magnetize the fusion fuel. In this work, we systematically study properties of Au–Ta alloy films in the entire compositional range from pure Au to pure Ta with thicknesses up to 30 µm. These films are made by direct current magnetron co-sputtering on planar substrates. Films are characterized by a combination of high-energy ion scattering, x-ray diffraction, electron microscopy, nanoindentation, and electrical transport measurements. Results show that an alloy with ~80 at.% of Ta forms a metallic glass exhibiting a maximum electrical resistivity of ~300 µΩ cm with a weak temperature dependence in the range of 5–400 K. The deposition of a film with ~80 at.% of Ta onto a sphero-cylindrical substrate for hohlraum fabrication is also demonstrated.

36 MATERIALS SCIENCE↗