Search NASA⌕ Search

SEARCH · Search NASA

Results for “THERMOPHYSICAL PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Thermophysical property and pore structure evolution in stressed and non-stressed neutron irradiated IG-110 nuclear graphite

The nuclear graphite, IG-110, was irradiated with and without a compressive load of 5 MPa at ~400 *C up to 9.3E25 n/m2 (E > 0.1 MeV). Following irradiation physical properties were studied to compare the effect of graphite irradiation on microstructure developed under compression and in stress-free conditions. Properties included: dimensional change, thermal conductivity, dynamic modulus, and CTE. The effect of stress on open internal porosity was determined through nitrogen adsorption. The IG-110 graphite experienced irradiation-induced creep that is differentiated from irradiation-induced swelling. Irradiation under stress resulted in somewhat greater thermal conductivity and coefficient of thermal expansion. While a significant increase in dynamic modulus occurs, no differentiation between materials irradiated with and without compressive stress was observed. Nitrogen adsorption analysis suggests a difference in pore evolution in the 0.3e40 nm range for graphite irradiated with and without stress, but this evolution is seen to be a small contributor to the overall dimensional change.

Snead, Lance↗
NASA NTRS2006

Thermophysical Properties Measurements of Zr62Cu20Al10Ni8

Thermophysical property studies performed at high temperature can prove challenging because of reactivity problems brought on by the elevated temperatures. Contaminants from measuring devices and container walls can cause changes in properties. To prevent this, containerless processing techniques can be employed to isolate a sample during study. A common method used for this is levitation. Typical levitation methods used for containerless processing are, aerodynamically, electromagnetically and electrostatically based. All levitation methods reduce heterogeneous nucleation sites, 'which in turn provide access to metastable undercooled phases. In particular, electrostatic levitation is appealing because sample motion and stirring are minimized; and by combining it with optically based non-contact measuring techniques, many thermophysical properties can be measured. Applying some of these techniques, surface tension, viscosity and density have been measured for the glass forming alloy Zr62Cu20Al10Ni8 and will be presented with a brief overview of the non-contact measuring method used.

Bradshaw, Richard C.↗
DOE OSTI2021

Saline: An API for Thermophysical Properties

An initial interface for thermophysical data was generalized for broader incorporation into modeling and simulation codes used for molten salt reactor analysis. A quality assurance review of the thermophysical properties data was conducted; errors were fixed, and improvements were made with consistency and accuracy to references. The Saline code application programming interface was created to facilitate access and integration of thermophysical properties. This report describes the thermophysical data, the quality assurance improvements, and the Saline interface.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1992

Thermophysical properties of lysozyme (protein) solutions

Thermophysical properties of protein solutions composed of the lysozyme crystals with a 0.1 M sodium acetate and 5 percent NaCl solution as the buffer (pH = 4.0) are determined. The properties being measured include specific heat, thermal conductivity, dynamic viscosity, and surface tension. The protein concentrations are varied. Thermal diffusivity is calculated using the measured results. The purpose of the research is to measure thermophysical properties of lysozyme solutions which would serve as the data bank for controlling and modeling the crystal growth process on earth as well as in space.

Liu, Jiaching↗
NASA NTRS1993

Electrostatic levitation technology for thermophysical properties of molten materials

Measurements of thermophysical properties of undercooled liquids often require some kind of levitator which isolates samples from container walls. We introduce in this presentation a high temperature/high vacuum electrostatic levitator (HTHVESL) which promises some unique capabilities for the studies of thermophysical properties of molten materials. Although substantial progress has been made in the past several months, this technology is still in the development stage, therefore, in this presentation we only focus on the present state of the HTHVESL(1) and point out other capabilities which might be realized in the near future.

Rhim, Won-Kyu↗
NASA NTRS1993

An overview of the measurements of thermophysical properties and some results on molten superalloys and semiconductors

This presentation consists of two parts: comments on the results of measurements on thermophysical properties based on the paper, 'Things Mother Never Taught Me (About Thermophysical Properties of Solids)' and results of thermophysical property measurements on selected solid and molten semiconductors and a proprietary superalloy. The first part may be considered as a tutorial for those involved in using or procuring thermophysical property data. The second part is presented as illustrations of what has been accomplished on molten materials at the Thermophysical Properties Research Laboratory (TPRL). The materials include Ge, PbTe, PbSnTe, HgCdTe and a superalloy.

Taylor, R. E.↗
DOE OSTI2022

Recent Progress in U-10Mo Mechanical and Thermophysical Property Characterization

Results are presented on the mechanical and thermophysical property characterization of U-10Mo as part of the MP-1 qualification campaign. The thermal diffusivity, specific heat and thermal conductivity of as fabricated U-10Mo fuel foils and plates were measured using the thermal conductivity microscope (TCM), differential scanning calorimeter (DSC) and laser flash analyzer (LFA) all of which located in a shielded glove box – thermal property cell (TPC). A novel inverse method based on finite element analysis was developed to evaluate the thermal diffusivity of composite/layered materials via the LFA technique such as the 5-lyered U-10Mo monolithic fuel mini-plates.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Atomistic Simulations for Thermophysical Properties of Uranium-Containing Halide Molten Salts

Characterizing the thermophysical properties in both fuel and coolant salts are critical in modeling, developing, process optimizing and utilizing molten salt reactors (MSRs), as these properties directly relate to operation metrics and can inform on the selection of candidate salts. The demand for consistent, accurate and publicly available thermophysical property data has become more apparent in recent years as interests have increased from molten salt reactor developers. There are a number of challenges in experimentally measuring properties such as thermal conductivity, viscosity, density and heat capacity , which have led to sparse and often times conflicting data points or molten salts in general. Additionally, there are a number of hazards to consider when synthesizing, storing, using, treating and disposing of molten salts. With the advances in computational capabilities over the last 10 years, the use of atomistic simulations can be implemented to support these efforts. The primary objective of this work is characterize the thermophysical transport properties in a number of molten chloride salts, and in particular NaCl-UCl 3 using ab-initio molecular dynamic (AIMD) simulations. In this binary salt the UCl 3 acts as the primary fissile material and NaCl acts as a carrier salt due with its’ high solubility for actinides A number of studies on the thermophysical properties of NaCl-UCl 3 have been published but there is not a vast amount of viscosity data for this system. In 1975, Desyatnik, et al published a study reporting dynamic viscosities that were calculated from kinematic viscosity measurements, and using the coefficients provided the viscosity in a 70:30 NaCl:UCl 3 mixture is 2.29 cP and 2.88 for a 60:40 mixture. Termini et al. recently reported viscosities in the range of 2.75 – 3 cP for the 63:37 NaCl-UCl 3 mixture in the same temperature range using rolling ball viscosity measurements. Computational viscosity of a similar mixture (64:36) can be obtained from the work Andersson et al. using the reported diffusion coefficients, and the hydrodynamic radius from the pair-radial distribution functions (RDFs). Using Eq (1) (vida infra), the viscosity would be 2.50 cP at 1100K. This is not to say that these values are incorrect due to the varying reported values, but aims to highlight the necessity of this work. The data reported in this ongoing work are computations on a 64:36 mixture of NaCl-UCl 3 at 987K. This work is likely to be expanded into varying concentrations of this mixture along with the inclusion of other salt candidate mixtures.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
NASA NTRS2018

Thermophysical Properties of Nickel-Based Superalloys

The NASA Marshall Space Flight Center (MSFC) electrostatic levitation (ESL) laboratory has a long history of providing materials research and thermophysical property data. The lab can measure thermophysical properties such as density, surface tension, and viscosity of liquid materials, including elements, alloys, glasses, ceramics, and oxides. Nickel-based superalloys (e.g. Inconel, Hastelloy, and Waspaloy) have many high performance applications, including turbine engines for aerospace. Superalloy parts are typically manufactured by casting and forging. These processes generate both polycrystalline and monocrystalline parts. A relatively new method of fabrication of turbine disk materials is additive manufacturing, which is typically done for aerospace parts by powder-bed methods such as selective laser melting (SLM). Accurate modeling of casting and forging, as well as additively manufacturing processes, require thermophysical properties (density, surface tension, and viscosity). The thermophysical properties of liquid nickel-based superalloys, both conventional and additively manufactured, were measured at several temperatures in both undercooled and superheated condition. Surface tension and viscosity was measured using the oscillating drop method and density and thermal expansion was measured using edge detection methods.

SanSoucie, Michael P.↗
NASA NTRS2004

Thermophysical Properties of Selected II-VI Semiconducting Melts

Thermophysical properties are essential for the accurate predication of the crystal growth process by computational modeling. Currently, the temperature dependent thermophysical property data for the II-VI semiconductor melts are scarce. This paper reports the results of the temperature dependence of melt density, viscosity and electrical conductivity of selected II-VI compounds, including HgTe, HgCdTe and HgZnTe. The melt density was measured using a pycnometric method, and the viscosity and electrical conductivity were measured by a transient torque method. The results were compared with and showed good agreement with the existing data in the literature.

Li, C.↗
NASA NTRS1999

Thermophysical Property Measurements of Molten Semiconductors in 1-g and Reduced-g Condition

Understanding and controlling the formation kinetics of varieties of crystal imperfections such as point defects, non uniform distribution of doping atoms, and impurity atoms in growing crystals are very important. Theoretical (numerical) modeling of the crystal growth process is an essential step to achieving these objectives. In order to obtain reliable modeling results, input parameters, i.e. various thermophysical parameters, must be accurate. The importance of accurate thermophysical properties of semiconductors in crystal growth cannot be overly emphasized. The total hemispherical emissivity, for instance, has a dramatic impact on the thermal environment. It determines the radiative emission from the surface of the melt which determines to a large extent the profile of the solidified crystal. In order to understand the convection and the turbulence in a melt, viscosity becomes an important parameter. The liquid surface tension determines the shape of the liquid-atmosphere interface near the solid-liquid-atmosphere triple point. Currently used values for these parameters are rather inaccurate, and this program intends to provide more reliable measurements of these thermophysical properties. Thus, the objective of this program is in the accurate measurements of various thermophysical properties which can be reliably used in the modeling of various crystal growth processes. In this program, thermophysical properties of molten semiconductors, such as Si, Ge, Si-Ge, and InSb will be measured as a function of temperature using the High Temperature Electrostatic Levitator at JPL. Each material will be doped by different kinds of impurities at various doping levels. Thermophysical properties which will be measured include: density, thermal expansion coefficient, surface tension, viscosity, specific heat, hemispherical total emissivity, and perhaps electrical and thermal conductivities. Many molten semiconductors are chemically reactive with crucibles. As a result, these dispersed impurities in the melts tend to substantially modify the properties of pure semiconductors. Sample levitation done in a vacuum clearly helps maintain the sample purity. However, in the 1-g environment, all gravity caused effects such as convection, sedimentation and buoyancy are still present in the sample. In addition, large forces needed to levitate a sample in the presence of the gravity can cause additional flows in the melt. The use of the High Temperature Electrostatic Levitator (HTESL) for the present research is a recent development and little is known about the flows induced by the electrostatic forces. In this ground base program, we will define the limits of HTESL technology as various thermophysical properties of molten semiconductors are measured.

Rhim, Won-Kyu↗
DOE OSTI2015

The calculation of thermophysical properties of nickel plasma

The thermophysical properties of Nickel plasma have been calculated for the temperatures 10–60 kK and densities less than 1 g/cm{sup 3}. These properties are the pressure, internal energy, heat capacity, and the electronic transport coefficients (electrical conductivity, thermal conductivity, and thermal power). The thermodynamic values have been calculated by means of the chemical model, which also allows one to obtain the ionic composition of considered plasma. The composition has been used to calculate the electronic transport coefficients within the relaxation time approximation. The results of the present investigation have been compared with the calculations of other researchers and available data of measurements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗