TPV Cell IV Curve Testing With Varying Black Body Emission Temperatures, Intensities, and Cell Temperatures
Thermophotoboltaics (TPV) is an energy conversion method whtih converts heat into electricity.
coefficients↗
SEARCH · Search NASA
Results for “TPV cells”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Characterization of Thermophotovoltaic Cells
Thermophotovoltaic (TPV) research has entered a period of rapid expansion after 30 years of effort, yet there is still no comprehensive method of TPV cell characterization. Simple procedures allow the derivation of temperature coefficients for Voc and Isc as well as the intensity coeffcient for Voc.
temperature thermophotovoltaic cells (TPV)↗
Thermophotovoltaic System Parametric Modeling
A small radioisotope powered TPV system was assumed. The system was simplified into a one-dimensional model with the emitter and heat rejection system as boundaries. Design equations were then developed which would allow parametric modeling of system efficiency, emitter radiation incident upon the TPV cell, energy converted in the TPV cell, and energy absorbed in the filter and cell-to-cell gaps. A figure of merit was then developed for the emitter, filter, and TPV cell.
thermophotovoltaic radioisotope TPV cells energy c↗
Electrochemical Characterization of Semiconductor Materials and Structures
For a period covering October 1, 1995 through August 12, 1996, the research group at CSU has conducted theoretical and experimental research on "Electrochemical Characterization of Semiconductor Materials and Structures. " The objective of this investigation was to demonstrate the applicability of electrochemical techniques for characterization of complex device structures based on InP and GaAs, Ge, InGaAs, InSb, InAs and InSb, including: (1) accurate EC-V net majority carrier concentration depth profiling, and (2) surface and bulk structural and electrical type defect densities. Our motivation for this R&D effort was as follows: "Advanced space solar cells and ThermoPhotoVoltaic (TPV) cells are fabricated using a large variety of III-V materials based on InP and GaAs for solar cells and low bandgap materials such as Ge, InGaAs, InAs and InSb for TPV applications. At the present time for complex device structures using these materials, however, there is no simple way to assess the quality of these structures prior to device fabrication. Therefore, process optimization is a very time consuming and a costly endeavor". Completion of this R&D effort would have had unquestionable benefits for space solar cell and TPV cells, since electrochemical characterization of the above cell structures, if properly designed can provide many useful structural and electrical material information virtually at any depth inside various layers and at the interfaces. This, could have been applied for step-by-step process optimization, which could have been used for fabrication of new generation high efficiency, low cost space PV and TPV cells.
Source record↗
Triple and Quadruple Junctions Thermophotovoltaic Devices Lattice Matched to InP
Thermophotovoltaic (TPV) conversion of IR radiation emanating from a radioisotope heat source is under consideration for deep space exploration. Ideally, for radiator temperatures of interest, the TPV cell must convert efficiently photons in the 0.4-0.7 eV spectral range. Best experimental data for single junction cells are obtained for lattice-mismatched 0.55 eV InGaAs based devices. It was suggested, that a tandem InGaAs based TPV cell made by monolithically combining two or more lattice mismatched InGaAs subcells on InP would result in a sizeable efficiency improvement. However, from a practical standpoint the implementation of more than two subcells with lattice mismatch systems will require extremely thick graded layers (defect filtering systems) to accommodate the lattice mismatch between the sub-cells and could detrimentally affect the recycling of the unused IR energy to the emitter. A buffer structure, consisting of various InPAs layers, is incorporated to accommodate the lattice mismatch between the high and low bandgap subcells. There are evidences that the presence of the buffer structure may generate defects, which could extend down to the underlying InGaAs layer. The unusual large band gap lowering observed in GaAs(1-x)N(x) with low nitrogen fraction [1] has sparked a new interest in the development of dilute nitrogen containing III-V semiconductors for long-wavelength optoelectronic devices (e.g. IR lasers, detector, solar cells) [2-7]. Lattice matched Ga1-yInyNxAs1-x on InP has recently been investigated for the potential use in the mid-infrared device applications [8], and it could be a strong candidate for the applications in TPV devices. This novel quaternary alloy allows the tuning of the band gap from 1.42 eV to below 1 eV on GaAs and band gap as low as 0.6eV when strained to InP, but it has its own limitations. To achieve such a low band gap using the quaternary Ga1-yInyNxAs1-x, either it needs to be strained on InP, which creates further complications due to the creation of defects and short life of the device or to introduce high content of indium, which again is found problematic due to the difficulties in diluting nitrogen in the presence of high indium [9]. An availability of material of proper band gap and lattice matching on InP are important issues for the development of TPV devices to perform better. To address those issues, recently we have shown that by adjusting the thickness of individual sublayers and the nitrogen composition, strain balanced GaAs(1-x)N(x)/InAs(1-y)N(y) superlattice can be designed to be both lattice matched to InP and have an effective bandgap in the desirable 0.4- 0.7eV range [10,11]. Theoretically the already reduced band gap of GaAs(1-x)N(x), due to the nitrogen effects, can be further reduced by subjecting it to a biaxial tensile strain, for example, by fabricating pseudomorphically strained layers on commonly available InP substrates. While such an approach in principle could allow access to smaller band gap (longer wavelength), only a few atomic monolayers of the material can be grown due to the large lattice mismatch between GaAs(1-x)N(x) and InP (approx.3.8-4.8 % for x<0.05, 300K). This limitation can be avoided using the principle of strain balancing [12], by introducing the alternating layers of InAs(1-y)N(y) with opposite strain (approx.2.4-3.1% for x<0.05, 300K) in combination with GaAs(1-x)N(x). Therefore, even an infinite pseudomorphically strained superlattice thickness can be realized from a sequence of GaAs(1-x)N(x) and InAs(1-y)N(y) layers if the thickness of each layer is kept below the threshold for its lattice relaxation
Bhusal, L.↗
Testing Thermophotovoltaic Cells With Black-Body Radiation
Method of testing thermophotovoltaic (TPV) cells involves maintaining cells at various temperatures while exposing cells to black-body radiation at various intensities from black-body sources at various other temperatures. Provides for simulation and evaluation of performance under variety of operating conditions and could become standard testing method for government and industry.
Lin, James J.↗
Inverted Three-Junction Tandem Thermophotovoltaic Modules
An InGaAs-based three-junction (3J) tandem thermophotovoltaic (TPV) cell has been investigated to utilize more of the blackbody spectrum (from a 1,100 C general purpose heat source GPHS) efficiently. The tandem consists of three vertically stacked subcells, a 0.74-eV InGaAs cell, a 0.6- eV InGaAs cell, and a 0.55-eV InGaAs cell, as well as two interconnecting tunnel junctions. A greater than 20% TPV system efficiency was achieved by another group with a 1,040 C blackbody using a single-bandgap 0.6- eV InGaAs cell MIM (monolithic interconnected module) (30 lateral junctions) that delivered about 12 V/30 or 0.4 V/junction. It is expected that a three-bandgap tandem MIM will eventually have about 3 this voltage (1.15 V) and about half the current. A 4 A/cm2 would be generated by a single-bandgap 0.6-V InGaAs MIM, as opposed to the 2 A/cm2 available from the same spectrum when split among the three series-connected junctions in the tandem stack. This would then be about a 50% increase (3xVoc, 0.5xIsc) in output power if the proposed tandem replaced the single- bandgap MIM. The advantage of the innovation, if successful, would be a 50% increase in power conversion efficiency from radioisotope heat sources using existing thermophotovoltaics. Up to 50% more power would be generated for radioisotope GPHS deep space missions. This type of InGaAs multijunction stack could be used with terrestrial concentrator solar cells to increase efficiency from 41 to 45% or more.
Wojtczuk, Steven↗
Thermophotovoltaics for In-Space Nuclear Power
In-space nuclear power systems are under consideration for missions that need lots of power. Recent work in Thermophotovoltaic (TPV) cells indicates that they may be a mass efficient option for converting a nuclear reactor’s thermal energy into electrical energy. This paper briefly trades TPV versus a Brayton Cycle in the context of a conceptual Earth-to-Mars transportation system. The selection of the heat engine primarily impacts the design of the nuclear reactor, power handling electronics, fluid loops, heat exchangers, and thermal radiator, so the impact to these subsystems is also considered. The mass and electrical power generation are the primary figures of merit compared between the two alternatives, and qualitative differences are discussed.
Nuclear↗
Thermophotovoltaics for In-Space Nuclear Power
In-space nuclear power systems are under consideration for missions that need lots of power. Recent work in Thermophotovoltaic (TPV) cells indicates that they may be a mass efficient option for converting a nuclear reactor’s thermal energy into electrical energy. This paper briefly trades TPV versus a Brayton Cycle in the context of a conceptual Earth-to-Mars transportation system. The selection of the heat engine primarily impacts the design of the nuclear reactor, power handling electronics, fluid loops, heat exchangers, and thermal radiator, so the impact to these subsystems is also considered. The mass and electrical power generation are the primary figures of merit compared between the two alternatives, and qualitative differences are discussed.
Nuclear↗
Ultra-Low-Cost Room Temperature SiC Thin Films
The research group at CSU has conducted theoretical and experimental research on 'Ultra-Low-Cost Room Temperature SiC Thin Films. The effectiveness of a ultra-low-cost room temperature thin film SiC growth technique on Silicon and Germanium substrates and structures with applications to space solar sells, ThermoPhotoVoltaic (TPV) cells and microelectronic and optoelectronic devices was investigated and the main result of this effort are summarized.
Faur, Maria↗
Development of Thermophotovoltaic Array Testing Capabilities
The present Jet Propulsion Laboratory (JPL) characterization test method for a single thermophotovoltaic (TPV) cell is to illuminate the cell with black body emission. However, this method is inadequate for the performance testing of a string or an array of cells. This is simply because the black body aperture is too small to supply sufficient illumination for much more than a single, small cell.
Thermophotovoltaic Array↗
TPVF Cell IV Curve Testing with Varying Black Body Emission Temperatures, Intensities, and Cell Temperature
A TPV GaSb cell was tested as part of an effort to establish a standard method of characterizing such cells.
repeatability↗
High efficiency thermal to electric energy conversion using selective emitters and spectrally tuned solar cells
Thermophotovoltaic (TPV) systems are attractive possibilities for direct thermal-to-electric energy conversion, but have typically required the use of black body radiators operating at high temperatures. Recent advances in both the understanding and performance of solid rare-earth oxide selective emitters make possible the use of TPV at temperatures as low as 1500 K. Depending on the nature of parasitic losses, overall thermal-to-electric conversion efficiencies greater than 20 percent are feasible.
Chubb, Donald L.↗
High efficiency direct thermal to electric energy conversion from radioisotope decay using selective emitters and spectrally tuned solar cells
Thermophotovoltaic (TPV) systems are attractive possibilities for direct thermal-to-electric energy conversion, but have typically required the use of black body radiators operating at high temperatures. Recent advances in both the understanding and performance of solid rare-earth oxide selective emitters make possible the use of TPV at temperatures as low as 1200K. Both selective emitter and filter system TPV systems are feasible. However, requirements on the filter system are severe in order to attain high efficiency. A thin-film of a rare-earth oxide is one method for producing an efficient, rugged selective emitter. An efficiency of 0.14 and power density of 9.2 W/KG at 1200K is calculated for a hypothetical thin-film neodymia (Nd2O3) selective emitter TPV system that uses radioisotope decay as the thermal energy source.
Chubb, Donald L.↗
Characterization of Thermophotovoltaic Cells
Explore the source record for details and available documents.
Thermophotovoltaic (TPV) TPV cell characterization↗
Buffer Layer Effects on Tandem InGaAs TPV Devices
Single junction indium gallium arsenide (InGaAs) based TPV devices have demonstrated efficiencies in excess of 20% at radiator temperatures of 1058 C. Modeling suggests that efficiency improvements in single bandgap devices should continue although they will eventually plateau. One approach for extending efficiencies beyond the single bandgap limit is to follow the technique taken in the solar cell field, namely tandem TPV cells. Tandem photovoltaic devices are traditionally composed of cells of decreasing bandgap, connected electrically and optically in series. The incident light impinges upon the highest bandgap first. This device acts as a sieve, absorbing the high-energy photons, while allowing the remainder to pass through to the underlying cell(s), and so on. Tandem devices reduce the energy lost to overexcitation as well as reducing the current density (Jsc). Reduced Jsc results in lower resistive losses and enables the use of thinner and lower doped lateral current conducting layers as well as a higher pitch grid design. Fabricating TPV tandem devices utilizing InGaAs for all of the component cells in a two cell tandem necessitates the inclusion of a buffer layer in-between the high bandgap device (In0.53 Ga0.47As - 0.74eV) and the low bandgap device (In0.66Ga0.34As - 0.63eV) to accommodate the approximately 1% lattice strain generated due to the change in InGaAs composition. To incorporate only a single buffer layer structure, we have investigated the use of the indium phosphide (InP) substrate as a superstrate. Thus the high-bandgap, lattice- matched device is deposited first, followed by the buffer structure and the low-bandgap cell. The near perfect transparency of the high bandgap (1.35eV) iron-doped InP permits the device to be oriented such that the light enters through the substrate. In this paper we examine the impact of the buffer layer on the underlying lattice-matched InGaAs device. 0.74eV InGaAs devices were produced in a variety of configurations both with and without buffer layers. All structures were characterized by reciprocal space x-ray diffraction to determine epilayer composition and residual strain. Electrical characterization of the devices was performed to examine the effect of the buffer on the device performance. The effect of the buffer structure depends upon where it is positioned. When near the emitter region, a 2.6x increase in dark current was measured, whereas no change in dark current was observed when it was near the base region.
Wilt, David M.↗
InGaAsSb/GaSb thermophotovoltaic cells
AstroPower is developing InGaAsSb thermophotovoltaic (TPV) devices. This photovoltaic cell is a two-layer epitaxial InGaAsSb structure formed by liquid-phase epitaxy on a GaSb substrate. The (direct) bandgap of the In(1 - x)Ga(x)As(1 -y)Sb(y) alloy is 0.50 to 0.55 eV, depending on its exact alloy composition (x, y); and is closely lattice-matched to the GaSb substrate The use of the quaternary alloy, as opposed to a ternary alloy - such as, for example, InGaAs/InP - permits low bandgap devices optimized for 1000 to 1500 C thermal sources with, with at the time, near-exact lattice matching to the GaSb substrate. Lattice-matching is important since even a small degree of lattice mismatch degrades device performance and reliability and increases processing complexity. For bandgaps of 0.52 eV,Fo internal quantum efficiencies as high as 95% have been measured at a wavelength of 2 microns. At 1 micron wavelengths, internal quantum efficiencies of 55% have been observed. The open-circuit voltage at currents of 0.3 A/sq cm is 0.220 volts and 0.260 V for current densities of 2 A/sq cm. Fill factors of 56% have also been measured. These preliminary results lead to the conclusion that the GaSb-based quaternary compounds provide a viable and high performance energy conversion solution for thermophotovoltaic systems operating with 1000 to 1500 C source temperatures.
Mauk, M. G.↗
InGaAsSb/GaSb thermophotovoltaic cells
AstroPower is developing InGaAsSb thermophotovoltaic (TPV) devices. This photovoltaic cell is a tvo-layer epitaxial InGaAsSb structure formed by liquid-phase epitaxy on a GaSb substrate The (direct) bandgap of the In(1-x)Ga(x)As(1-y)Sb(y) alloy is 0.50 to 0.55 eV, depending on its exact alloy composition (x,y); and is closely lattice-matched to the GaSb substrate. The use of the quaternary alloy as opposed to a ternary alloy -- such as, for example, InGaAs/InP -- permits low bandgap devices optimized for 1000 to 1500 C thermal sources with, at the same time, near-exact lattice matching to the GaSb substrate. Lattice-matching is important since even a small degree of lattice mismatch degrades device performance and reliability and increases processing complexity. Internal quantum efficiencies as high as 95% have been measured at a wavelength of 2 microns. At 1 micron wavelengths, internal quantum efficiencies of 55% have been observed. The open-circuit voltage at currents of 0.3 A/cm(exp 2) is 0.220 volts and 0.260 V for current densities of 2 A/cm(exp 2). Fill factors of 56% have been measured at 60 mA/cm(exp 2). However as current density increases there is some decrease in fill factor. Our results to date snow that the GaSb-based quaternary compounds provide a viable and high performance energy conversion solution for thermophotovoltaic systems operating with 1000 to 1500 C source temperatures.
Shellenbarger, Z. A.↗