Search NASA⌕ Search

SEARCH · Search NASA

Results for “TUBING, RECTANGULAR - STRENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Predicting Rupture Pressure and Leak Rate of Alloy 600 Tubes with ODSCC and Comparing with Test Results (Technical Letter Report)

This report summarizes structural integrity work performed for the U.S. NRC that predicts the rupture pressure and leak rate of flawed steam generator (SG) tubes. The work includes pressure testing of straight tubes with lab-induced outer diameter stress corrosion cracks (ODSCC). Existing models for predicting rupture pressure and leak rate of straight tubes with well-defined, rectangular, electro-discharge-machined (EDM) flaws were modified and used to predict the measured rupture pressures and leak rates from straight tubes with ODSCC. Models previously developed for EDM notches in straight tubes were modified for ODSCC by using the equivalent rectangular crack (ERC) method.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Predicting Rupture Pressure and Leak Rate of Alloy 600 U-bend Tubes with PWSCC and Comparing with Test Results (Technical Letter Report)

This report summarizes structural integrity work performed for the US NRC that predicts the structural integrity of steam generator (SG) tubes with flaws in the U-bend. The work covers model development and validation for U-bend tubes containing lab-induced primary water stress corrosion cracks (PWSCC). Limit load models for plastic collapse predicting ligament rupture pressure and leak rate of cracked U-bend tubes were developed and validated with pressure tests and finite element analyses (FEAs). Failure pressure and leak rate tests were conducted at room temperature on Alloy 600 U-bend tubes containing flaws located at various locations around the U-bend. Existing models for predicting structural integrity of straight tubes with well defined, rectangular, electro-discharge-machined (EDM) flaws were modified and used to predict the ligament rupture and unstable burst pressures as well as leak rates for the PWSCC flaws in the U-bend section.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

RUScal : Software for the analysis of resonant ultrasound spectroscopy measurements

Resonant ultrasound spectroscopy is used to nondestructively measure the elastic resonances of small solids to elucidate the material's elastic properties or other qualities like size, shape, or composition. In this work, we introduce the software RUScal for the purpose of determining elastic properties by analyzing the eigenfrequencies of solid specimens with common shapes, such as rectangular parallelepipeds, cylinders (solid and hollow tube), ellipsoids, and octahedrons, as well as irregularly shaped ellipsoids that can be described analytically. All symmetry classes are supported, from isotropic to triclinic, along with the option to add or remove up to three orthogonal mirror planes as well as the ability to reorient the crystal axes with respect the sample edges via Euler angles. Additional features include tools to help find initial sets of elastic constants, including grid exploration and Monte Carlo methods, a tool to analyze frequencies as a function of sample length or crystal orientation, an error analysis tool to assess fit quality, and formatting of the input and output files for batch fitting, e.g., as a function of temperature. This software was validated with published resonant ultrasound spectroscopy data for various materials, shapes, and symmetries with noted improvements in calculation time compared to finite element methods.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Surface Roughness Effects on Heat Transfer in Additively Manufactured sCO 2 Cycle Heat Exchangers

An experimental study was performed to consider the impact of surface roughness on heat transfer and pressure drop to supercritical carbon dioxide (sCO 2 ) in additively manufactured channels. All tests were performed in the Heat Exchange and Experimental Testing (HEET) rig at the U.S. Department of Energy’s (DOE) National Energy Technology Laboratory (NETL) in Morgantown, West Virginia. Four test articles were considered. The first was a hydrodynamically smooth, drawn tube. The other three were additively manufactured channels with square and rectangular cross sections, which were characterized by sand-grain roughness to hydraulic diameter ratios spanning 0.0029 to 0.0073. Friction factors were determined by measuring the tube mass flow rate and pressure drop. The tube side heat transfer coefficient was measured using the Wilson plot technique. It was found that the friction factor results were 8% greater than the Colebrook correlation. Greater deviation was observed between the heat transfer results and the correlations. The Gnielinski correlation overpredicted the experimental points by nominally 30% and the Norris correlation overpredicting the experimental points by nominally 25%. A thermal performance factor was formed from the friction factor augmentation and Nusselt number augmentation results. These results indicated a 10% improvement in heat duty for a heat exchanger constructed utilizing a tube with ϵ/D_h =0.0073 relative to a heat exchanger utilizing a smooth, conventional tube.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Method of generation of planar plasma jets

Applications of dielectric barrier discharge (DBD) based atmospheric pressure plasma jets are often limited by the relatively small area of treatment due to their 1D configuration. This system generates 2D plasma jets permitting fast treatment of larger targets. DBD evolution starts with formation of transient anode glow, and continues with development of cathode-directed streamers. The anode glow can propagate as an ionization wave along the dielectric surface through and outside of the discharge gap. Plasma propagation is not limited to 1D geometry such as tubes, and can be organized in a form of a rectangular plasma jet, or other 2D or 3D shapes. Also described are a method for generating 2D plasma jets and use of the 2D plasma jets for cancer therapy.

Dobrynin, Danil V.↗
DOE OSTI2020

Laminar drag reduction in microchannels with liquid infused textured surfaces

Liquid infused surfaces (LIS) achieve non-wetting properties through asperity structures containing pockets of a lubricating liquid rather than air. Although studies have demonstrated several potential applications of LIS, the effect of liquid infused texture on the flow of liquid in microchannels has not been systematically addressed. The present work focuses on the effect of liquid-infused texture geometry and the infused liquid properties on the flow characteristics of a bulk fluid in rectangular and round microchannel geometries. Considering four different textured geometries of transverse ridges, longitudinal ridges, in-lined square posts and staggered squares, a detailed parametric study is presented to assess the resulting drag reduction and friction factor, expressed in terms of the Poiseuille number, on the flow in microchannels. The effect of geometrical parameters is investigated for different asperity solid fraction (Φ s ), asperity height (h s ) and channel thickness (H) or tube diameter (D), while the effect of the infused fluid is studied in terms of a ratio of its viscosity relative to the viscosity of the flowing bulk fluid. Based on the results of the parametric study an extension of the conventional Moody diagram for non-wetting surfaces is developed. Finally, a design of experiments study is conducted to relate the drag reduction and Poiseuille number to the various governing parameters, using which conditions that maximize drag reduction are identified.

42 ENGINEERING↗