Search NASA⌕ Search

SEARCH · Search NASA

Results for “Test Standards”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Ruggedness Evaluation of ASTM International Standard Test Methods for Shape Memory Materials: E3098 Standard Test Method for Mechanical Uniaxial Pre-strain and Thermal Free Recovery of Shape Memory Alloys

This paper evaluates the ruggedness testing of the recently released ASTM International E3098 Standard Test Method for Mechanical Uniaxial Pre-strain and Thermal Free Recovery of Shape Memory Alloys. The ruggedness experiment was designed with eight runs in two replicates, consisting of seven factors: strain rate (ė), heating and cooling rates (Ṫ heat and Ṫ cool , respectively), upper and lower cycle temperatures (UCT and LCT, respectively), hold time (t hold ), and minimum load (F min ) imparted on the samples. The results indicate that the strain rate factor had no effect on any result variable, whereas the minimum load factor had a large effect on several result variables including the austenite start and martensite finish temperatures as well as most of the strain measurements from the thermal cycle. The lower cycle temperature factor had a large effect on the stress at maximum strain during pre-straining (e i ), denoted by S i , at ~7.2 MPa, as well as the A f , at 5.47 °C. Closely following the LCT effect, Ṫ heat was found to have a large effect on the austenite start temperature (A s ), at a value of ~2.72 °C. The testing methodology, analysis techniques, and resulting conclusions on the ruggedness of the test method are presented.

Shape memory alloys↗
NASA NTRS2019

Ruggedness Evaluation of ASTM International Standard Test Methods for Shape Memory Materials: E3097 Standard Test Method for Mechanical Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys

This paper evaluates the ruggedness testing of the newly released ASTM International E3097 Standard Test Method for Mechanical Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys. The ruggedness experiment was designed with eight runs in two replicates, consisting of seven factors of strain rate (ė), heating and cooling rates (T(sub heat) and T(sub cool), respectively), upper and lower cycle temperatures (UCT and LCT, respectively), hold time (t(sub hold)), and minimum load (F(sub min)) imparted on the samples. The results indicate that the hold time factor had no effect on any result variable. The minimum load factor, alternatively, had the greatest effect on several result variables, with the greatest influence on the strains at martensite start and finish (strain variation ~0.1 percent), and the strains at the upper and lower cycle temperatures (strain variation of 0.14 percent). The UCT was found to have a large effect on the austenite and martensite finish tangent line and data intersect, denoted by A(sub f(sup *)) and M(sub f(sup*)), by ~17 and 4 °C, respectively. The testing methodology, analysis techniques, and resulting conclusions on the ruggedness of the test methods are presented.

Benafan, Othmane↗
NASA NTRS2022

Ruggedness Evaluation of ASTM International Standard Test Methods for Shape Memory Materials: E3097 Standard Test Method for Mechanical Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys

This paper evaluates the ruggedness testing of the newly released ASTM International E3097 Standard Test Method for Mechanical Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys. The ruggedness experiment was designed with eight runs in two replicates, consisting of seven factors of strain rate (ė), heating and cooling rates (Ṫ(heat) and Ṫ(cool), respectively), upper and lower cycle temperatures (UCT and LCT, respectively), hold time (thold), and minimum load (Fmin) imparted on the samples. The results indicate that the hold time factor had no effect on any result variable. The minimum load factor, alternatively, had the greatest effect on several result variables, with the greatest influence on the strains at martensite start and finish (strain variation ~0.1 percent), and the strains at the upper and lower cycle temperatures (strain variation of 0.14 percent). The UCT was found to have a large effect on the austenite and martensite finish tangent line and data intersect, denoted by Af* and Mf*, by ~17 and 4 °C, respectively. The testing methodology, analysis techniques, and resulting conclusions on the ruggedness of the test methods are presented.

shape memory alloy↗
NASA NTRS1946

Correlation between strength properties in standard test specimens and molded phenolic parts

This report describes an investigation of the tensile, flexural, and impact properties of 10 selected types of phenolic molding materials. The materials were studied to see in what ways and to what extent their properties satisfy some assumptions on which the theory of strength of materials is based: namely, (a) isotropy, (b) linear stress-strain relationship for small strains, and (c) homogeneity. The effect of changing the dimensions of tensile and flexural specimens and the span-depth ratio in flexural tests were studied. The strengths of molded boxes and flexural specimens cut from the boxes were compared with results of tests on standard test specimens molded from the respective materials. The nonuniformity of a material, which is indicated by the coefficient of variation, affects the results of tests made with specimens of different sizes and tests with different methods of loading. The strength values were found to depend on the relationship between size and shape of the molded specimen and size and shape of the fillers. The most significant variations observed within a diversified group of materials were found to depend on the orientation of fibrous fillers. Of secondary importance was the dependence of the variability of test results on the pieces of filler incorporated into the molding powder as well as on the size of the piece. Static breaking strength tests on boxes molded from six representative phenolic materials correlated well with falling-ball impact tests on specimens cut from molded flat sheets. Good correlation was obtained with Izod impact tests on standard test specimens prepared from the molding materials. The static breaking strengths of the boxes do not correlate with the results of tensile or flexural tests on standard specimens.

MATERIALS, MONSANTO RESINOX↗
NASA NTRS1953

An Analysis of the Tracking Performances of Two Straight-wing and Two Swept-wing Fighter Airplanes with Fixed Sights in a Standardized Test Maneuver

Standard air-to-air-gunnery tracking runs were conducted with F-51H, F8F-1, F-86A, and F-86E airplanes equipped with fixed gunsights. The tracking performances were documented over the normal operating range of altitude, Mach number, and normal acceleration factor for each airplane. The sources of error were studied by statistical analyses of the aim wander.

CONTROL, LATERAL↗
NASA NTRSDate not supplied

Analysis of Igniter/Promoter Material Effects on Burn Length Variability in Astm G124 Standard Testing

ASTM G124 refers to the “Standard Test Method for Determining the Combustion Behavior of Metallic Materials in Oxygen Enriched Atmospheres”. Major test parameters are well defined in the standard and a detailed description of how to set up and conduct the test is also included. However, one variable - the igniter/promoter system - is not clearly restricted or specified. Due to the fact that this igniter/promoter system is not definitively specified, multiple materials have been used. This lack of specificity in igniter/promoter material was identified as a potential source of variability in test results, and as such has been selected for this study as a parameter to analyze and identify if the igniters/promoters should be standardized. For that purpose, several igniter/promoter systems have been selected (that were currently in use at various laboratories) which would be tested via ASTM G124 with Inconel 718 test rods. Testing was conducted over two phases – the first for screening promoter effects in the transition region of the material, and the second for comparing measured flammability thresholds identified through testing by each igniter/promoter type. The results of this study have found that igniter/promoter material is not a statistically significant factor in the variability of burn length in test samples. Initial results showing variability was likely due to small sample size, as the issue became less pronounced once more samples were tested and more data generated. Each of the igniter/promoter systems tested were effective at determining flammability thresholds and so it is concluded that no specific igniter/promoter needs to be identified in the ASTM G124 test standard.

oxygen compatibility↗
NASA NTRS1984

USL/DBMS NASA/PC R and D project system testing standards

A set of system testing standards to be used in the development of all C software within the NASA/PC Research and Development Project is established. Testing will be considered in two phases: the program testing phase and the system testing phase. The objective of these standards is to provide guidelines for the planning and conduct of program and software system testing.

Dominick, Wayne D.↗
NASA NTRS1996

Standard Test Methods for Textile Composites

Standard testing methods for composite laminates reinforced with continuous networks of braided, woven, or stitched fibers have been evaluated. The microstructure of these textile' composite materials differs significantly from that of tape laminates. Consequently, specimen dimensions and loading methods developed for tape type composites may not be applicable to textile composites. To this end, a series of evaluations were made comparing testing practices currently used in the composite industry. Information was gathered from a variety of sources and analyzed to establish a series of recommended test methods for textile composites. The current practices established for laminated composite materials by ASTM and the MIL-HDBK-17 Committee were considered. This document provides recommended test methods for determining both in-plane and out-of-plane properties. Specifically, test methods are suggested for: unnotched tension and compression; open and filled hole tension; open hole compression; bolt bearing; and interlaminar tension. A detailed description of the material architectures evaluated is also provided, as is a recommended instrumentation practice.

Masters, John E.↗
NASA NTRS2015

Test Standard Revision Update: JESD57, "Procedures for the Measurement of Single-Event Effects in Semiconductor Devices from Heavy-Ion Irradiation"

The JEDEC JESD57 test standard, Procedures for the Measurement of Single-Event Effects in Semiconductor Devices from Heavy-Ion Irradiation, is undergoing its first revision since 1996. In this talk, we place this test standard into context with other relevant radiation test standards to show its importance for single-event effect radiation testing for space applications. We show the range of industry, government, and end-user party involvement in the revision. Finally, we highlight some of the key changes being made and discuss the trade-space in which setting standards must be made to be both useful and broadly adopted.

heavy ion↗
NASA NTRS1998

Test Standard Developed for Determining the Slow Crack Growth of Advanced Ceramics at Ambient Temperature

The service life of structural ceramic components is often limited by the process of slow crack growth. Therefore, it is important to develop an appropriate testing methodology for accurately determining the slow crack growth design parameters necessary for component life prediction. In addition, an appropriate test methodology can be used to determine the influences of component processing variables and composition on the slow crack growth and strength behavior of newly developed materials, thus allowing the component process to be tailored and optimized to specific needs. At the NASA Lewis Research Center, work to develop a standard test method to determine the slow crack growth parameters of advanced ceramics was initiated by the authors in early 1994 in the C 28 (Advanced Ceramics) committee of the American Society for Testing and Materials (ASTM). After about 2 years of required balloting, the draft written by the authors was approved and established as a new ASTM test standard: ASTM C 1368-97, Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Ambient Temperature. Briefly, the test method uses constant stress-rate testing to determine strengths as a function of stress rate at ambient temperature. Strengths are measured in a routine manner at four or more stress rates by applying constant displacement or loading rates. The slow crack growth parameters required for design are then estimated from a relationship between strength and stress rate. This new standard will be published in the Annual Book of ASTM Standards, Vol. 15.01, in 1998. Currently, a companion draft ASTM standard for determination of the slow crack growth parameters of advanced ceramics at elevated temperatures is being prepared by the authors and will be presented to the committee by the middle of 1998. Consequently, Lewis will maintain an active leadership role in advanced ceramics standardization within ASTM. In addition, the authors have been and are involved with several international standardization organizations including the Versailles Project on Advanced Materials and Standards (VAMAS), the International Energy Agency (IEA), and the International Organization for Standardization (ISO). The associated standardization activities involve fracture toughness, strength, elastic modulus, and the machining of advanced ceramics.

Choi, Sung R.↗
NASA NTRS1981

Frequency standard test facility data acquisition and processing system

The interim frequency standards test facility tests all frequency standards used in the DSN. It is also the central testing facility for testing all ultrastable hydrogen maser frequency standards. This proposed data acquisition/processing system was designed to support the IFSTF by acquiring and processing the large amounts of data generated there.

Knapp, L. J.↗
NASA NTRS2023

Establishing Standardized Test Methods for Evaluating Space Suit Gloves

The Artemis space suit glove environmental protection garment (EPG) will be the first line of protection used to protect the crewmember’s hands from the environments encountered during extravehicular activity (EVA). As the Artemis missions will include more extreme environments, it is necessary to define tests to evaluate if gloves can meet new, challenging requirements. The NASA Engineering and Safety Center (NESC)has funded an effort with the goal to help vendors to produce a space suit glove that is sufficiently durable to meet the needs of the Artemis missions. Three problems were identified in meeting that goal. First, there are no standardized tests defined to evaluate the durability of space suit gloves for the extreme lunar environments. Second, there is insufficient data on glove performance in a lunar environment from which to compare new designs. And third, current ISS glove TMG fabrics are unlikely to be sufficient to meet Lunar requirements. Four tasks were established to answer different aspects of these three problems. Task 1 focused on the characterization of potential glove fabrics using ASTM standardized test methods when possible. When one did not exist, new standardized test procedures were devised. Task 2 focused on developing a procedure for characterizing the thermal performance of a glove assembly. Task 3 focused on devising a standard procedure for characterizing the dust/abrasion resistance of a space suit glove. Task 4 focused on devising a standard procedure for characterizing the cut resistance of a space suit glove while at cryogenic temperatures. The new procedures created in Tasks 2, 3 and 4 were then validated by testing the Phase VI glove to collect baseline data. This paper will summarize the approach used to establish standardized test methods for each task and will expound on the ASTM process to publish the new standards.

spacesuit↗
NASA NTRSDate not supplied

Establishing Standardized Test Methods for Evaluating Space Suit Gloves

The Artemis space suit glove environmental protection garment (EPG) will be the first line of protection used to shield the crewmember’s hands from the environments encountered during extravehicular activity (EVA). As the Artemis missions will include more extreme environments than those experienced on the International Space Station, development, verification, and validation of gloves poses three key challenges. First, there are no standardized tests defined to evaluate the durability of space suit gloves for the extreme lunar environments, particularly the permanently shadowed regions. Second, there is insufficient data on state-of-the-art glove performance in a lunar environment from which to compare new designs. Third, current ISS glove Thermal Micrometeoroid Garment (TMG) fabrics are unlikely to be sufficient to meet Lunar requirements. It is therefore necessary to define tests to evaluate if gloves can meet new, challenging requirements. This paper focuses on the development of a test procedure to characterize lunar EVA glove fabrics using ASTM standardized test methods and the design and validation of a new standardized test procedure for comparing abrasion resistance between fabrics in lunar-like conditions. The results of testing on twelve candidate EVA glove fabrics are presented.

Robert J. Jones↗
NASA NTRS2006

Comparison of JPL and European Environmental Testing Standards

A comparison of JPL and European environmental testing standards is presented. The contents include: 1) JPL Environmental Testing Documents; 2) Focus of the Comparison; 3) Test Policy; 4) Documentation; 5) Programmatics; 6) Functional Testing; 7) Reporting; 8) Dynamics Test Levels, Durations, & Margins; 9) Thermal Test Levels, Durations, & Margins; and 10) EMC Test Levels, Durations, & Margins.

spacecraft↗
NASA NTRS1971

The fabrication, testing and delivery of boron/epoxy and graphite/epoxy nondestructive test standards

A description is given of the boron/epoxy and graphite/epoxy nondestructive test standards which were fabricated, tested and delivered to the National Aeronautics and Space Administration. Detailed design drawings of the standards are included to show the general structures and the types and location of simulated defects built into the panels. The panels were laminates with plies laid up in the 0 deg, + or - 45 deg, and 90 deg orientations and containing either titanium substrates or interlayered titanium perforated shims. Panel thickness was incrementally stepped from 2.36 mm (0.093 in.) to 12.7 mm (0.500 in.) for the graphite/epoxy standards, and from 2.36 mm (0.093 in.) to 6.35 mm (0.25 in.) for the boron/epoxy standards except for the panels with interlayered shims which were 2.9 mm (0.113 in.) maximum thickness. The panel internal conditions included defect free regions, resin variations, density/porosity variations, cure variations, delaminations/disbonds at substrate bondlines and between layers, inclusions, and interlayered shims. Ultrasonic pulse echo C-scan and low-kilovoltage X-ray techniques were used to evaluate and verify the internal conditions of the panels.

Pless, W. M.↗