Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thermophysics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Thermophysical property and pore structure evolution in stressed and non-stressed neutron irradiated IG-110 nuclear graphite

The nuclear graphite, IG-110, was irradiated with and without a compressive load of 5 MPa at ~400 *C up to 9.3E25 n/m2 (E > 0.1 MeV). Following irradiation physical properties were studied to compare the effect of graphite irradiation on microstructure developed under compression and in stress-free conditions. Properties included: dimensional change, thermal conductivity, dynamic modulus, and CTE. The effect of stress on open internal porosity was determined through nitrogen adsorption. The IG-110 graphite experienced irradiation-induced creep that is differentiated from irradiation-induced swelling. Irradiation under stress resulted in somewhat greater thermal conductivity and coefficient of thermal expansion. While a significant increase in dynamic modulus occurs, no differentiation between materials irradiated with and without compressive stress was observed. Nitrogen adsorption analysis suggests a difference in pore evolution in the 0.3e40 nm range for graphite irradiated with and without stress, but this evolution is seen to be a small contributor to the overall dimensional change.

Snead, Lance↗

Active Thermochemical Tables: the thermophysical and thermochemical properties of methyl, CH 3 , and methylene, CH 2 , corrected for nonrigid rotor and anharmonic oscillator effects

The thermophysical properties (isobaric heat capacity, entropy, enthalpy increment) of two prominent radicals, methyl, CH 3 , and methylene, CH 2 , were computed using the Nonrigid Rotor Anharmonic Oscillator (NRRAO) approach and compared to their RRHO counterparts, demonstrating significant differences between the results from the two approaches. Methylene presents a typical case in which the NRRAO thermophysical properties have significantly higher values than their RRHO counterparts at higher temperatures. In the case of methyl, the positive anharmonicity of the umbrella motion causes an opposite effect, and the NRRAO corrected thermophysical properties have lower values than their RRHO counterparts. The NRRAO corrected thermophysical properties, in turn, affect the resulting thermochemical properties. Here, two reactions important in combustion modelling were tested: the recombination of methyl radical with hydrogen atoms to form methane, and the recombination of two methyl radicals to form ethane. The related NRRAO equilibrium constants differ significantly from their RRHO analogs, and the consequences for chemical modelling are discussed. Also reported are the most current ATcT enthalpies of formation for CH n (n = 4-0) species and for C 2 H 6 , together with the tightly related sequential bond dissociation enthalpies along with the CHn series.

74 ATOMIC AND MOLECULAR PHYSICS↗

An ab initio molecular dynamics investigation of the thermophysical properties of molten NaCl-MgCl 2

Molten salts have many applications in the nuclear and solar energy industries for thermal storage and heat transfer applications. However, there is a knowledge gap in molten salt thermophysical properties which hinders the technical readiness level of molten salt applications, especially in the nuclear industry. A common method of investigating new materials is through ab initio Molecular Dynamics (AIMD) simulations which is an effective tool to investigate structural and thermophysical properties at realistic temperatures. NaCl-MgCl 2 is an inexpensive salt that is a good candidate for use as a heat transfer medium in solar power applications or in the secondary loop of a nuclear reactor. In this article, the thermophysical properties of NaCl-MgCl 2 are computed via AIMD calculations to supplement the limited experimental studies in the literature. Here a wide range of compositions and temperatures for the pseudo-binary NaCl-MgCl 2 were used to calculate the density, heat capacity, compressibility, enthalpy of mixing, and volumetric thermal expansion coefficient. AIMD is shown to accurately model the densities of molten NaCl-MgCl 2 as there is good agreement with the available literature. This work observed a transition to a monotonic increase of the density with respect to MgCl 2 composition occurring above 1100 K. The heat capacity values increase uniformly with respect to concentration of MgCl 2 at a rate of 2.85 J/mol-K per 10 mol% of MgCl 2 . Select thermophysical properties are fit to a Redlich-Kister expansion for utilization in multiphysics simulations.

36 MATERIALS SCIENCE↗

Mechanical and Thermophysical Properties of 3D-Printed SiC before and after Neutron Irradiation – FY21

This report presents the mechanical and thermophysical properties of 3D-printed SiC before and after neutron irradiation that have been evaluated to assess the fuel matrix material for the Transformational Challenge Reactor (TCR). The TCR fuel form consists of an additively-manufactured silicon carbide (SiC) matrix and uranium nitride tristructural isotropic (UN TRISO) fuel particles, which is manufactured through a newly developed processing route combining binderjet 3D printing, TRISO fuel particle loading, and chemical vapor infiltration (CVI). Because the fuel matrix is a primary component of the TCR core and its response to mechanical and thermal loads during operation is one of the most influential factors on the integrity of TCR core, testing and evaluation have focused on producing mechanical and thermophysical properties data for the binderjet/CVI SiC. Baseline mechanical and thermophysical properties were measured from the disk specimens printed for different and sizes orientations, which included equibiaxial flexural failure strength, elastic constants, thermal diffusivity and conductivity, density, and the coefficient of thermal expansion. Flexural failure strength datasets showed similar Weibull distributions regardless of sample variants including different orientations. The mean failure strengths of the 3D-printed SiC variants were in the range of 280–310 MPa, which are slightly lower than that of the chemical vapor deposition (CVD) SiC. Thermophysical test results showed that specific heat and thermal expansion are not sensitive to the build direction of SiC samples, while thermal conductivity is highly dependent on the build direction and can be correlated to the anisotropic character of the 3D-printed SiC. Neutron irradiation tests were carried out on the 3D-printed 6-mm diameter SiC disk specimens. Irradiation was carried to 2.3 dpa over a temperature range of 360–880°C. No significant degradation in strength was observed in SiC after irradiations in various conditions and with different orientations. Anisotropy that had been observed in the thermal conductivity of 3D-printed SiC prior to irradiation vanished after irradiation as the irradiation defect thermal resistivity accumulated in the material. Electron microscopy of the microstructure after neutron irradiation showed distinct defect morphologies in the heterogenous material, but no evidence for irradiation-induced cracking or degradation in the microstructure was observed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Saline: An API for Thermophysical Properties

An initial interface for thermophysical data was generalized for broader incorporation into modeling and simulation codes used for molten salt reactor analysis. A quality assurance review of the thermophysical properties data was conducted; errors were fixed, and improvements were made with consistency and accuracy to references. The Saline code application programming interface was created to facilitate access and integration of thermophysical properties. This report describes the thermophysical data, the quality assurance improvements, and the Saline interface.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

An Overview of the Molten Salt Thermal Properties Database–Thermophysical, Version 4.0 (MSTDB-TP V.4.0)

A central repository of thermophysical and thermochemical properties of molten salt compositions of relevance to molten salt reactors (MSRs) is vital in supporting the broad community of MSR developers, who are at various stages of developing and deploying their reactor designs. In general, these MSR designs differ significantly from developer to developer (e.g., with respect to the hardness of the neutron spectra, level of fissile loading, target multicomponent temperatures and power levels, and moderating capabilities). Therefore, the fuel and coolant salts being considered vary greatly: they may be chlorides or fluorides, they utilize different actinides at different ratios, and the cations in the melt are selected based on perceived advantages and disadvantages. Considering the general need for thermal properties, and the vastness of the array of potential candidate salt mixtures, the Molten Salt Thermal Properties Database (MSTDB) was initiated in 2018 with the goal of providing thermophysical and thermochemical characterization of key molten salt compounds and mixtures across their temperature and compositional domains. The MSTDB is thus divided into the thermophysical arm (MSTDB-TP) and the thermochemical arm (MSTDB-TC). The MSTDB is an effort funded by the Department of Energy, Office of Nuclear Energy (DOE-NE) Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, and the MSR Campaign. This report provides an overview of the MSTDB-TP v4.0 in terms of the data contained within, the state of the tools used to access the data, the availability of predictive models that leverage the raw data in the database, the preliminary status of developmental efforts that are currently underway, and an account of future goals for MSTDB-TP. The primary goal for the update from MSTDB-TP v.3.1 to v4.0 was the incorporation of surface tension data into the database; this property is important for thermal hydraulics modeling and species transport in other tools that have been developed under the NEAMS program. A breakdown of the surface tension data that have been added into MSTDB-TP v4.0 is provided herein, and the manner in which the quality of the data has been assessed is also documented. For MSTDB-TP v4.0, newly published thermophysical property data—primarily from collaborative experimental efforts under the MSR Campaign—have been incorporated into the database, and the resulting expansion is documented here. Because of the size to which MSTDB-TP has grown, the raw data format has now been recast into JavaScript Object Notation (JSON) format for easier connection with the MSTDB-TP application programming interface (API). Saline; the pre-existing comma-separated value (CSV) format has been deprecated but is still maintained, accessible, and up to date. As a final effort in packaging the MSTDB-TP v4.0 update, the graphical user interface (GUI) for MSTDB has been updated to allow full accessibility to the density and viscosity predictive models, which are based on Redlich-Kister expansions of MSTDB-TP raw data. Some other major aspects of this report, in terms of preliminary and future work, include: (1) documentation of the formalism and preliminary testing of a kinetic theory model that may act as a predictive model for thermal conductivity; (2) documentation of the candidate predictive models that may be considered in the future for surface tension, making use of the surface tension data now in MSTDB-TP v4.0; (3) a preliminary account of a data collection process that will enable the filling of additional gaps within MSTDB-TP, namely with data which have been collected computationally (e.g., through ab initio molecular dynamics).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Atomistic Simulations for Thermophysical Properties of Uranium-Containing Halide Molten Salts

Characterizing the thermophysical properties in both fuel and coolant salts are critical in modeling, developing, process optimizing and utilizing molten salt reactors (MSRs), as these properties directly relate to operation metrics and can inform on the selection of candidate salts. The demand for consistent, accurate and publicly available thermophysical property data has become more apparent in recent years as interests have increased from molten salt reactor developers. There are a number of challenges in experimentally measuring properties such as thermal conductivity, viscosity, density and heat capacity , which have led to sparse and often times conflicting data points or molten salts in general. Additionally, there are a number of hazards to consider when synthesizing, storing, using, treating and disposing of molten salts. With the advances in computational capabilities over the last 10 years, the use of atomistic simulations can be implemented to support these efforts. The primary objective of this work is characterize the thermophysical transport properties in a number of molten chloride salts, and in particular NaCl-UCl 3 using ab-initio molecular dynamic (AIMD) simulations. In this binary salt the UCl 3 acts as the primary fissile material and NaCl acts as a carrier salt due with its’ high solubility for actinides A number of studies on the thermophysical properties of NaCl-UCl 3 have been published but there is not a vast amount of viscosity data for this system. In 1975, Desyatnik, et al published a study reporting dynamic viscosities that were calculated from kinematic viscosity measurements, and using the coefficients provided the viscosity in a 70:30 NaCl:UCl 3 mixture is 2.29 cP and 2.88 for a 60:40 mixture. Termini et al. recently reported viscosities in the range of 2.75 – 3 cP for the 63:37 NaCl-UCl 3 mixture in the same temperature range using rolling ball viscosity measurements. Computational viscosity of a similar mixture (64:36) can be obtained from the work Andersson et al. using the reported diffusion coefficients, and the hydrodynamic radius from the pair-radial distribution functions (RDFs). Using Eq (1) (vida infra), the viscosity would be 2.50 cP at 1100K. This is not to say that these values are incorrect due to the varying reported values, but aims to highlight the necessity of this work. The data reported in this ongoing work are computations on a 64:36 mixture of NaCl-UCl 3 at 987K. This work is likely to be expanded into varying concentrations of this mixture along with the inclusion of other salt candidate mixtures.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Comparison of the effects of measured and computed thermophysical properties of nanofluids on heat transfer performance

This article reports a comparison of the differences between using measured and computed thermophysical properties to describe the heat transfer performance of TiO{sub 2}-water nanofluids. In this study, TiO{sub 2} nanoparticles with average diameters of 21 nm and a particle volume fraction of 0.2-1 vol.% are used. The thermal conductivity and viscosity of nanofluids were measured by using transient hot-wire apparatus and a Bohlin rotational rheometer, respectively. The well-known correlations for calculating the thermal conductivity and viscosity of nanofluids were used for describing the Nusselt number of nanofluids and compared with the results from the measured data. The results show that use of the models of thermophysical properties for calculating the Nusselt number of nanofluids gave similar results to use of the measured data. Where there is a lack of measured data on thermophysical properties, the most appropriate models for computing the thermal conductivity and viscosity of the nanofluids are the models of Yu and Choi and Wang et al., respectively. (author)

36 MATERIALS SCIENCE↗

Thermophysical Properties and Corrosion Characterization of Low Cost Lithium Containing Nitrate Salts Produced in Northern Chile for Thermal Energy Storage

In recent years, lithium containing salts have been studied for thermal energy storage (TES) systems applications, because of their optimal thermophysical properties. In solar power plants, lithium is seen as a way to improve the properties of molten salts used today. Lithium nitrate is a good candidate for sensible heat storage, due to its ability to increase the salt mixture's working temperature range. In the present research, thermophysical properties characterization of lithium nitrate containing salts, produced in Chile, have been carried out. Corrosion evaluations of carbon and low chromium steels were performed at 390 degrees C for 1000 hours. Thermophysical properties of the salt mixtures, such as thermal stability and heat capacity, were measured before and after corrosion tests. Chemical composition of the salts was also determined and an estimation of Chilean production costs is reported. Results showed that purity, thermal stability and heat capacity of the salts were reduced, caused by partial thermal decomposition and incorporation of corrosion products from the steel.

14 SOLAR ENERGY↗

Molten Chloride Thermophysical Properties, Chemical Optimization, and Purification

Next-generation concentrating solar power (CSP) technology requires high-temperature heat-transfer fluids and thermal energy storage that can operate in the temperature range of 500°–720°C. This high temperature demands a new chemistry for the heat-transfer fluids that must have high-temperature thermal and chemical stabilities, high energy density, and low corrosion rate on metallic materials used in the heat exchangers, piping, and thermal energy storage tanks. A ternary MgCl 2 -KCl-NaCl chloride-salt system has been proposed to achieve such goals, given its high-temperature thermal stability. The chloride-salt-based systems have been used by the metallurgy industry as the electrolyte to electrolytically extract metallic magnesium. They have also attracted attentions from the nuclear industry for developing the molten salt fast reactors that can operate at close to atmospheric pressure and at higher temperature than traditional light-water reactors. However, the corrosion properties of the ternary salt are not well known. The corrosion mechanism is believed to be correlated to the presence of MgOHCl impurity at the operation temperature. MgOHCl is fundamentally caused by the hygroscopic nature of the MgCl 2 component. Therefore, the first key objective of this project is to understand the nature of the corrosiveness of the ternary chloride-salt system and its prevention by designing new lab-scale purification processes. Because of its importance, a working group called the Chloride Salt Collective across multiple U.S. Department of Energy national laboratories is established to gain experimental agreement on the corrosion behaviors. In addition, water generation during salt dehydration could lead to highly corrosive HCl/water mixture via a hydrolysis process between water and anhydrous MgCl 2 or MgCl 2 hydrates. MgOHCl will eventually be converted to MgO particulates regardless of the chemical path chosen (i.e., by thermal decomposition, chemical purification with an active metal, or electrochemical purification utilizing the reduction power of electron flows). Large MgO particles with high hardness can wear out bearing and bushing and even clog the delicate channels in the primary heat exchanger. Because of this, a second objective is to understand the chemistry behind salt purification and transfer the scientific understanding to a set of engineering know-how for large-scale salt melter design. Because there is limited information on the thermophysical properties and the sensitivity of these properties around the targeted salt composition, a third objective is to measure thermophysical properties relevant to system and component design and support Topic 1 Liquid Pathway development. For example, composition shift due to salt reaction with water can be a potential issue because it can lead to changes of thermophysical properties, such as (1) melting point (or freeze point), which can jeopardize safe operation of the supercritical CO 2 power cycle proposed for next-generation CSP, and (2) heat capacity and density, which can decrease the overall power-generation capability of the plants. The value of the thermal conductivity of the selected salt composition is also a critical criterion for the solar receiver design.

14 SOLAR ENERGY↗

Short- to Intermediate-Range Structure, Transport, and Thermophysical Properties of LiF–NaF–ZrF4 Molten Salts

LiF–NaF–ZrF 4 multicomponent molten salts are identified as promising candidates for coolant salts in molten salt reactors and advanced high-temperature reactors. This study focused on low-melting point salt compositions of interest: 38LiF–51NaF–11ZrF 4 , 42LiF–29NaF–29ZrF 4 , and 26LiF–37NaF–37ZrF 4 . Ab-initio molecular dynamics (AIMD) calculations were performed and compared with available experimental data to assess the ability of rigid ion models (RIM) to reproduce short- to intermediate-range structure, transport, and thermophysical properties of the LiF–NaF–ZrF 4 salt mixtures. It is found that as ZrF 4 mol% increases, the average cation–anion coordination number (CN) of monovalent cations (Li + , Na + ) obtained from RIM calculations decreases, while multivalent Zr 4+ CN varied from 15% to 19% in comparison to corresponding AIMD values. In addition, RIM is found to predict the existence of 7, 8, and 9 coordinated fluorozirconate complexes, while AIMD and the available experimental data showed an occurrence of 6, 7, and 8 coordinated complexes in the melt. The intermediate-range structure analysis revealed that while the RIM parameters are able to reproduce a local structure for lower ZrF 4 mol% salts such as in 38LiF–51NaF–11ZrF 4 , an extensive fluorozirconate network formation is observed in RIM simulations for higher ZrF 4 mol% compositions. The network generated by RIM parameters is found to be mainly connected by “corner-sharing” fluorozirconate complexes as opposed to both “edge-sharing” and “corner-sharing” connectively portrayed by AIMD. It is found that a close agreement between AIMD and the RIM salt structure for the 11-mol% ZrF 4 salt resulted in good agreement in the calculated Zr diffusivities and the viscosity values. However, due to the inaccurate short- to intermediate-range structure prediction by RIM for higher ZrF 4 mol% compositions, thermophysical properties such as densities and heat capacity differ by up to 26% and 27%, respectively, upon comparison with AIMD and experimental values. Also, the network-dominated properties such as diffusion coefficients and viscosities differed by up to two and three orders of magnitude, respectively. This study signifies the importance of accurate salt structure generation for an accurate prediction of transport and thermophysical properties of multicomponent molten salts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Synthesis of multi-hierarchical structured yttria-stabilized zirconia powders and their enhanced thermophysical properties

Multi-hierarchical structured yttria-stabilized zirconia (YSZ) powders were successfully synthesized by a hydrothermal-calcination process. The morphology, crystallinity, and microstructure of the products were characterized by SEM, XRD, TEM, and BET. A possible formation mechanism of the unique structure formed during hydrothermal processing was also investigated. The measured thermophysical results indicated that the prepared YSZ powders had a low thermal conductivity (0.63–1.27 W m⁻¹ K⁻¹), good short-term high-temperature stability up to 1300 °C. The influence of the morphology and microstructure on their thermophysical properties was briefly discussed. The unique multi-hierarchical structure makes the prepared YSZ powders candidates for use in enhanced applications involving thermal barrier coatings. - Graphical abstract: There are many tiny pores and grain boundaries in the multi-hierarchical structured yttria-stabilized zirconia (YSZ) powders,which greatly decrease the thermal conductivities of the YSZ powders. - Highlights: • Multi-hierarchical structured YSZ powders were successfully prepared. • The prepared YSZ powders had a low thermal conductivity (0.63–1.27 W m⁻¹ K⁻¹). • Improved high-temperature stability had been achieved for the prepared YSZ powders. • The influence of the morphology on their thermophysical properties was explored.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Preparation and thermophysical properties of (Sm{sub 1−x}Er{sub x}){sub 2}Ce{sub 2}O{sub 7} oxides for thermal barrier coatings

Graphical abstract: - Highlights: • These ceramic materials with fluorite structure were synthesized. • Defect points lead to their lower thermal conductivities. • The lower ionic radius of Er{sup 3+} ion leads to the reduction of thermal expansion coefficient of (Sm{sub 1−x}Er{sub x}){sub 2}Ce{sub 2}O{sub 7} oxides. - Abstract: (Sm{sub 1−x}Er{sub x}){sub 2}Ce{sub 2}O{sub 7} ceramics were synthesized by sol–gel method and sintered at 1600 °C for 10 h in air. The influence of Er{sub 2}O{sub 3}-substitution on the phase structure and thermophysical properties of Sm{sub 2}Ce{sub 2}O{sub 7} was investigated. The phase structures of these ceramics were identified by X-ray diffraction showing that all synthesized ceramics have fluorite-type structure. The measurements for thermophysical properties of these ceramics show that their thermal conductivities and thermal expansion coefficients remarkably decreased through Er-substitution. However, the thermal expansion coefficients were higher than that of YSZ and their thermal conductivities were much lower than that of 8YSZ. The excellent thermophysical property implies that these solid solutions are potential materials for the ceramics layer in thermal barrier coatings.

36 MATERIALS SCIENCE↗

Thermophysical Properties of Alloy 617 from 25°C to 1000°C

Key thermophysical properties needed for the successful design and use of Alloy 617 in steam generator and heat exchanger applications have been measured experimentally, and results are compared with literature values and results obtained from some other commercial Ni–Cr alloys and model materials. Specifically, the thermal diffusivity, thermal expansion coefficient, and specific heat capacity have been measured for Alloy 617 over a range of temperatures, allowing calculation of thermal conductivity up to 1000 degrees C. It has been found that the thermal conductivity of Alloy 617 exhibits significant deviation from monotonic behavior in the temperature range from 600 degrees C to 850 degrees C, the temperatures of interest for most heat transfer applications. The non-linear behavior appears to result primarily from short-range order/disorder phenomena known to occur in the Ni–Cr system. Similar deviation from monotonic behavior was observed in the solid solution Ni–Cr-W Alloy 230, and lesser deviations were observed in iron based Alloy 800H and an austenitic stainless steel. Measured thermophysical property data are provided for four different heats of Alloy 617, and it is shown that property variations between the four different heats are not significant. Measurements were also obtained from Alloy 617 that was aged for up to 2000 h at 750 degrees C, and it was found that this aging treatment does not significantly influence the thermophysical properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Thermophysical Properties of Multiphase Borosilicate Glass-Ceramic Waste Forms

Multiphase borosilicate glass-ceramics represent one candidate to contain radioactive nuclear waste separated from used nuclear fuel. In this work, the thermophysical properties from room temperature to 1273 K were investigated for four different borosilicate glass-ceramic compositions containing waste loadings from 42 to 60 wt% to determine the sensitivity of these properties to waste loading, as-fabricated microstructure, and potential evolutions in microstructure brought about by temperature transients. The thermal expansion, specific heat capacity, thermal diffusivity, and thermal conductivity are presented. The impact of increasing waste loading is shown to have a small but measurable effect on the thermophysical properties between the four compositions, contrasted to a much greater impact observed when transitioning from predominantly crystalline to amorphous systems. Thermal cycling below 1273 K was not found to measurably impact the thermophysical properties of the compositions investigated here.

Glass Ceramic↗

Molten Salt Thermophysical Properties Database Development: 2019 Update

This report provides an update on the molten salt reactor thermophysical properties database that is being developed as part of the U.S. Department of Energy Advanced Reactor Technology Program Molten Salt Reactor (MSR) campaign. A summary of recent MSR-relevant literature and a discussion of data gaps are provided. The structure of the new MSR thermophysical properties database is outlined and three datasets are reviewed in detail to provide examples of the data and metadata that will be included in the database. Despite the availability of some high quality MSR-relevant data-sets, there remains a need for a thermophysical properties experimental program to generate data focused on addressing the design and licensing needs of current MSR concept developers. This report represents the work product milestone M4AT-19AN040601045 for work package Salt Chemistry work package AT-19AN04060104 of the Advanced Reactor Technology Program’s MSR campaign.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗