SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The effects of oxide content level and variations in thermomechanical processing upon the final structure and properties of HDA 8077 sheet have been systematically examined. It was found that creep strength and formability are substantially influenced by both oxide content and TMP schedule. Variations in creep properties obtained appear to correlate with observed microstructures.
In support of the RNA world hypothesis, previous studies identified trimetaphosphate (Tmp) as a plausible energy source for RNA world organisms. In one of these studies, catalytic RNAs (ribozymes) that catalyze the triphosphorylation of RNA 5'-hydroxyl groups using Tmp were obtained by in vitro selection. One ribozyme (TPR1) was analyzed in more detail. TPR1 catalyzes the triphosphorylation reaction to a rate of 0.013 min -1 under selection conditions (50 mM Tmp, 100 mM MgCl 2 , 22°C). To identify a triphosphorylation ribozyme that catalyzes faster triphosphorylation, and possibly learn about its secondary structure TPR1 was subjected to a doped selection. The resulting ribozyme, TPR1e, contains seven mutations relative to TPR1, displays a previously unidentified duplex that constrains the ribozyme's structure, and reacts at a 24-fold faster rate than the parent ribozyme. Under optimal conditions (150 mM Tmp, 650 mM MgCl 2 , 40°C), the triphosphorylation rate of TRP1e reaches 6.8 min -1 .
In 2012, a pathfinder forward pressure vessel bulkhead (FPVBH) for the Orion Multi-Purpose Crew Vehicle (MPCV) was fabricated using aluminum (Al) alloy 2219. The demonstration article was offered as a replacement for the baseline configuration, which at that time was a multi-piece welded construction using aluminum-lithium (Al-Li) alloy 2195. In 2014, the NASA Engineering and Safety Center (NESC) funded a Phase I effort to explore spin-forming as a manufacturing method to produce a complex-shaped, single-piece FPVBH for the crew module (CM) [1]. The primary focus of the NESC effort was to expand spin-forming technology to the fabrication of an Al-Li 2195 FPVBH. As a result, limited testing and analysis was performed on the original Al 2219 article. In this study, a sufficiently large plate of Al 2219 was not available for the fabrication of a FPVBH. Therefore, the forming blank comprised two plates (from different lots) butt welded together using a single friction stir weld. The welded forming blank was then spin formed into the FPVBH configuration and heat treated to the T62 temper. Mechanical property testing of the spin-formed 2219-T62 FPVBH revealed that the tensile properties were comparable to the Metallic Material Properties Development and Standardization (MMPDS) A-basis allowable for Al 2219-T6 wrought products. However, post-spin forming application of the standard heat treatment produced large, recrystallized grains in the material. The response varied within the two plates; one plate lot exhibited nearly complete recrystallization, while the other lot contained bands of recrystallization. Although no reduction in tensile properties was observed due to these microstructural variations, a more detailed investigation was recommended to better understand the effect of spin forming on the recrystallization mechanism and the impact on other material properties. The current study examined the microstructure and mechanical properties of the fully processed Al 2219-T62 FPVBH with emphasis on comparing differences between the two plates. Testing was limited to the cone region of the FPVBH. The two specific tasks in this study were: a) Characterization of the microstructure and mechanical properties in the two plates used in the FPVBH. b) Isolation of the impact of each step in the thermo-mechanical processing (TMP) sequence of the FPVBH on recrystallization and grain growth. Mechanical property testing sampled regions containing both large, recrystallized and small, unrecrystallized grains. Tensile strengths and elongations were equivalent in both regions and exceeded MMPDS A-basis allowables. Fracture toughness was equivalent in both regions and fracture morphology was typical of aluminum alloys. The fatigue precrack region of the fracture toughness specimens appeared more faceted in the recrystallized plate. This suggests that property testing that is more sensitive to grain size, such as fatigue crack growth rate and stress corrosion cracking, may be warranted. Alcoa reviewed the production records for the two plate lots and confirmed that composition of both plates was within the allowable range for Al 2219 and that plate processing steps were all performed within production limits. However, the Fe content was notably higher in the fully recrystallized plate, resulting in a greater volume fraction of large Fe-bearing inclusions and Al-Cu constituent particles. Alcoa did not provide details regarding plate processing variables for the two plate lots. It was surmised that deformation by hot rolling was the most accurate TMP simulation of commercial spin forming within a laboratory setting. Both hot rolling and spin forming comprise combinations of shear and compressive deformation. The through-thickness strain caused by hot rolling is symmetrical about the mid-plane, as the rollers contact both sides of the material. Shear strains are maximum at the inner and outer surfaces and trend toward zero at the mid-thickness. In contrast, spin forming utilizes a single roller on the outer surface, producing a gradient in shear stress through the thickness. Shear strains in spin-formed material are highest at the outer surface due to direct contact with the roller, and trend toward zero at the inner surface. Consequently, there will undoubtedly be some discrepancies in the mechanical response of hot-rolled and spin-formed products in the through-thickness direction. Interrupted TMP simulations were performed on remnant plate from the FPVBH forming blank in order to isolate the effects of a post-weld anneal, spin-forming deformation/thermal cycling, and solution heat treatment (SHT) on development of the recrystallized microstructures. Analysis confirmed that large, recrystallized grains formed exclusively during SHT and only after a certain deformation level was exceeded. Remnant plate from both lots that received thermal processing only did not exhibit recrystallization but exhibited fully recrystallized microstructures when processed by hot rolling. This indicates that (1) the level of deformation exceeded the critical level for recrystallization in both plates and (2) that the level of deformation during hot rolling was greater than that which accumulated during spin forming of the FPVBH. Comparison of the hot-rolled plate with the spin-formed material showed that the recrystallized grain size was larger in the FPVBH, providing further evidence that deformation levels were lower in the FPVBH. The most plausible explanation for the differing degrees of recrystallization in the two plates is particle stimulated nucleation (PSN) at the Fe-bearing inclusions and large Al-Cu constituent particles. In the plate with higher solute content, the greater volume fraction of these particles reduces the deformation level required to promote recrystallization. During spin forming the critical deformation level was likely exceeded for the higher Fe content plate resulting in a fully recrystallized microstructure. The lower Fe content plate developed a microstructure that exhibited bands of recrystallization due to the combination of a non-uniform distribution of particles and deformation. The critical deformation required for recrystallization was likely only exceeded during spin forming in regions of higher particle content. While there were differences in Fe content between these lots of Al 2219 plate, the composition of both was within defined alloy limits and Alcoa reported no anomalies during plate production. The observed differences in recrystallization after spin forming may reflect the inherent variability between these two lots of plate. The spin-forming vendor, Spincraft, reported that similar variations in recrystallized microstructures have been observed during examination of multiple spin-forming trials of a different 2xxx series aluminum alloy. Hence, tighter chemical specification limits on impurity levels in Al 2219 plate may help ensure uniform, predictable microstructures. Finally, the tensile and fracture toughness properties were not affected by the microstructural variations noted.
The high specific impulse (Isp) of Nuclear Electric Propulsion (NEP) technology offers the potential for advanced space mission capabilities. However, the five critical technology elements of NEP vehicles have yet to prove technical maturity levels for consideration into mission design. In response to the critical reviews by the NASA Engineering and Safety Center (NESC) and the National Academies of Sciences, Engineering, and Medicine (NASEM), NASA’s Space Nuclear Propulsion (SNP) project created an NEP Technology Maturation Plan (TMP) for focused development of NEP technology. The TMP called for a coordinated set of technology development efforts to meet this objective. The Modular Assembled Radiators for NEP VehicLes (MARVL) Early Career Initiative (ECI) project was initiated to develop a portion of the fifth Critical Technology Element (CTE) of the NEP vehicle: the Primary Heat Rejection Subsystem (PHRS). A target application of a 2039 human-rated Mars mission was outlined in the TMP. For the outlined mission, a NEP vehicle will experience several thermal environments which will impact the design and operation of the PHRS. To maintain radiator temperatures within the required effective temperature range, the effect of natural, induced, and NEP internally generated heat loads on the radiator panel must be well understood. Furthermore, this analysis is critical for analyzing the influence of various orientations and positions of the NEP vehicle relative to nearby celestial bodies throughout the mission. This study conducted a complete enveloping analysis of the thermal environments influencing the NEP vehicle throughout the mission. Thermal analysis was conducted for the radiator panels based on the defined mission environments. This thermal analysis concludes with the selection of ideal radiator orientations for the NEP vehicle, and the identification of worst case hot and cold environmental sink temperatures throughout the mission. For the target application, the environmental sink temperature while the reactor is powered OFF or powered ON ranges from 30 K to 353 K and 2.7 K to 243 K respectively. When considering interplanetary space, the minimum environmental sink temperature when the reactor is powered OFF and the radiators are oriented “edge to Sun” is 2.7 K. The environmental thermal models generated in this study will be used for future studies with the full vehicle system model. The environmental sink temperature curves generated will be used for future radiator and component analysis to predict transient performance in the space environment. The environmental sink temperature and heat rejection capability curves will inform the trade between commissioning orbits that are in consideration. The model may also serve as a useful tool as reference for future crewed space missions, missions involving radiators or temperature sensitive equipment, or other missions requiring analysis of natural orbital thermal environments.
Nucleoside 5'-polyphosphates (N5PP) formed when solutions of nucleoside 5'-phosphates (N5P) and trimetaphosphate (TMP) are dessicated at room temperature are studied by paper chromatography, electrophoresis, and metal catalytic reactions. Divalent Mg ion exhibited superior catalytic function to other divalent metal ions in the reaction. Major reaction products are indicated. The importance of the N5PP series, TMP, and N5-triphosphate as substrates of RNA and DNA synthesis, and under postulated prebiotic conditions likely to obtain during prebiological ages of the earth, is emphasized and discussed. Alternate drying and wetting, evaporation from a prebiotic puddle, concentration of solubles in the remaining liquid phase, metal catalysis, and the role of these substances in the formation of amino acids and long-chain polyphosphates are considered.
Various multiple strain-anneal cycles (1000 C) were imposed on specimens of the directionally solidified eutectic (DSE) alloy gamma/gamma prime-alpha to identify thermomechanical processing methods (TMP) which would improve the creep behavior. Specimens of the Ni-32.3Mo-6.3Al wt pct alloy were grown with a modified Bridgeman technique. Some of the cylindrical specimens were alternately heat-treated at 900 C, then strained, or heat-treated only, while other specimens were annealed at 900 C after swaging and then worked at ambient temperature. The specimens were all examined microstructurally using transmission electron microscopy, some before and after being exposed to constant-load compression tests at 1000 C. The creep strain increased for all TMP specimens for strain rates of at least 2 millionths per sec. Strain rates of about 2 ten millionths per sec were only improved with strain annealing with 13 percent work at ambient temperature. A slight improvement, compared to as-grown materials, was observed in the 1000 C creep behavior of materials annealed at 900 C. Strain-annealing was found to introduce three-dimensional dislocation networks into the gamma-prime matrix.
The compressive slow plastic flow behavior of several B2 crystal structure NiAl intermetallics has been studied in air between 1000 and 1400 K. Small grain-sized Ni-48.25 at. pct Al (of about 10 microns) was found to be stronger than the previously studied 17 microns diameter material. While grain refinement improved the strength at all test temperatures, the exact mechanism is not clear. Experiments at lower temperature revealed that composition as well as grain size can be an important factor, since Ni-49.2Al was weaker than Ni-48.25Al. Pronounced yield points were found during slow strain-rate testing at 1000 K; however, continued deformation appears to take place by the same mechanism(s) as found at high temperatures. Small changes in thermomechanical processing (TMP) schedules to fabricate Ni-49.2Al indicated that basic deformation characteristics (stress exponent and activation energy) are not affected; however, the preexponential term could be modified if TMP alters the grain structure.
Space Life Sciences Directorate (SLSD) specializes in transitioning technology and knowledge to medical operations. This activity encompasses funding a spectrum of research and technology efforts, such as understanding fundamental biological mechanisms altered by microgravity and executing technology watches for state of the art diagnostic imaging equipment. This broad spectrum approach to fulfilling the need to protect crewmember health and performance during long and short duration missions to the International Space Station, moon and Mars is made possible by having a line of site between research and operations. Currently, SLSD's line of site is articulated in a transition to medical practice (TMP) process. This process is designed to shepherd information and knowledge gained through fundamental and mechanistic research toward the development of an operational solution such as a pre-flight selection criteria; an in-flight countermeasure, monitoring capability or treatment; or a post-flight reconditioning program. The TMP process is also designed to assist with the customization of mature hardware or technology for NASA specific use. The benefits of this process are that the concept of operational usability is interjected early in the research, design, or acquisition phase, and stakeholders are involved early to identify requirements and also periodically asked to assess requirements compliance of research or technology development project. Currently a device known as the actiwatch is being assessed for the final transition to operational use. Specific examples of research to operations transition success help to illustrate the process and bolster communication between the research and medical operations communities.
Over the last two years NASA’s Space Nuclear Propulsion (SNP) Project formulated a Technology Maturation Plan (TMP) for development of the sub-systems needed for a MW-class Nuclear Electric Propulsion (NEP) system which, combined with a high thrust chemical propulsion stage, would be suitable for human missions to Mars. Two recent assessments, independently conducted by the National Academies for Science, Engineering, and Medicine and the NASA Engineering & Safety Center, concluded that the technologies required for a high-power NEP system are immature and the attendant risks insufficiently quantified to justify initiating a flight project. For NEP to be available as a viable option to meet flight opportunities in the late 2030s / 2040s time frame, development of the key sub-systems must begin now. SNP has subdivided the NEP system into five Critical Technology Elements (CTE): the nuclear reactor, power conversion, power management and distribution, electric propulsion sub-system, and the primary heat rejection system. Development plans for each of these CTEs have been drafted which will serve as the template for a focused milestone-driven research and development campaign intended to advance each CTE to Technology Readiness Level (TRL) 5. This will be accomplished by building and testing hardware at relevant power levels (~ 1 MW) and for relevant durations (2,500 hours, ~10% of the required operational lifetime) and conducting numerical modeling of the CTEs anchored by the accumulated test data to predict system performance and reliability. Concurrent with this work, high-level coupled system/mission modeling will be carried out to refine the key performance parameters that the various CTEs must achieve. Non-advocate reviews will be held at milestone points to assess progress and inform down-select decisions. The strategy for formulating the TMP was described previously; this paper describes ongoing progress on the drafting and baselining of the plan, including key specific details.
Over the last two years NASA’s Space Nuclear Propulsion (SNP) Project formulated a Technology Maturation Plan (TMP) for development of the sub-systems needed for a MW-class Nuclear Electric Propulsion (NEP) system which, combined with a high thrust chemical propulsion stage, would be suitable for human missions to Mars. Two recent assessments, independently conducted by the National Academies for Science, Engineering, and Medicine and the NASA Engineering & Safety Center, concluded that the technologies required for a high-power NEP system are immature and the attendant risks insufficiently quantified to justify initiating a flight project. For NEP to be available as a viable option to meet flight opportunities in the late 2030s / 2040s time frame, development of the key sub-systems must begin now. SNP has subdivided the NEP system into five Critical Technology Elements (CTE): the nuclear reactor, power conversion, power management and distribution, electric propulsion sub-system, and the primary heat rejection system. Development plans for each of these CTEs have been drafted which will serve as the template for a focused milestone-driven research and development campaign intended to advance each CTE to Technology Readiness Level (TRL) 5. This will be accomplished by building and testing hardware at relevant power levels (~ 1 MW) and for relevant durations (2,500 hours, ~10% of the required operational lifetime) and conducting numerical modeling of the CTEs anchored by the accumulated test data to predict system performance and reliability. Concurrent with this work, high-level coupled system/mission modeling will be carried out to refine the key performance parameters that the various CTEs must achieve. Non-advocate reviews will be held at milestone points to assess progress and inform down-select decisions. The strategy for formulating the TMP was described previously*; this paper describes ongoing progress on the drafting and baselining of the plan, including key specific details. * “Strategy for Developing Technologies for Megawatt-class Nuclear Electric Propulsion Systems”, K.A. Polzin, et. al., International Electric Propulsion Conference IEPC 2022, IEPC-2022-155
Development of two models for the condensation of nucleotides under possibly prebiotic conditions. In the first of these models this type of reaction is promoted by the presence of imidazole and substituted imidazole compounds. The second model involves the condensation of mononucleotides with cyanamide in the presence and absence of a prototemplate such as polyornithine. A tentative mechanism for the role of imidazole catalysis in phosphodiester bond formation between adjacent TMP molecules is suggested.
Thermomechanical processing (TMP) was evaluated as a method of strengthening normally tough iron-12-nickel-reactive metal alloys at cryogenic temperatures. Five iron-12 nickel alloys with reactive metal additions of aluminum, niobium, titanium, vanadium, and aluminum plus niobium were investigated. Primary evaluation was based on the yield strength and fracture toughness of the thermomechanically processed alloys at -196 C.
Some illustrative results obtained from work accomplished under the aerothermoelasticity work breakdown structure (WBS) element of the National Aerospace Plane (NASP) Technology Maturation Program (TMP) are presented and discussed. The objectives of the aerothermoelasticity element were to develop analytical methods applicable to aerospace plane type configurations, to conduct analytical studies to identify potential problems, to evaluate potential solutions to problems, and to provide an experimental data base to verify codes and analytical trends. Work accomplished in the three areas of experimental data base, unsteady aerodynamics, and integrated analysis methodology are described. Some of the specific topics discussed are: (1) transonic wind tunnel aeroelastic model tests of cantilever delta wing models, of an all-moveable delta-wing model, and of aileron buzz models; (2) unsteady aerodynamic theory correlation with experiment and theory improvements; and (3) integrated analysis methodology results for thermal effects on vibration, for thermal effects on flutter, and for improving aeroelastic performance by using active controls.
The 2(prime)-d-5(prime)-GMP and 2(prime)-d-5(prime)-AMP bind 2 times more strongly to montmorillonite 22A than do 2(prime)-d-5(prime)-CMP and 5(prime)-TMP. The dinucleotide d(pG)2 forms in 9.2 percent yield and the cyclic dinucleotide c(dpG)2 in 5.4 percent yield in the reaction of 2(prime)-d-5(prime)-GMP with EDAC in the presence of montmorillonite 22A. The yield of dimers which contain the phosphodiester bond decreases as the reaction medium is changed from 0.2 M NaCl to a mixture of 0.2 M NaCl and 0.075 M MgCl2. A low yield of d(pA)2 was observed in the condensation reaction of 5(prime)-ImdpA on montmorillonite 22A. The yield of d(pA)2 obtained when EDAC is used as the condensing agent increases with increasing iron content of the Na(+)-montmorillonite used as catalyst. Evidence is presented which shows that the acidity of the Na(+)-montmorillonite is a necessary but not sufficient factor for the montmorillonite catalysis of phosphodiester bond formation.
Variations in thermomechanical processing (TMP) which regulate the microstructural characteristics and superplastic response of an Al-10Mg-0.1Zr alloy at 300 C were evaluated. Mechanical property data revealed that the superplastic ductility can be enhanced by simultaneously increasing the total rolling strain, the reduction per pass, and the duration of reheating intervals between passes during isothermal rolling. Texture and microscopy data were consistent with the development of a refined microstructure by recovery-dominated processes, i.e., continuous recrystallization, during the processing. The mechanisms by which a refined substructure can be progressively converted into a fine-grained structure during repeated cycles of deformation and annealing are addressed. A qualitative description of the complex sequence of developments leading to a microstructure better suited to support superplastic response is presented.
The Al-Cu-Li phase diagram indicates that during thermomechanical processing of Al 2090 at 300 C both T(1) and T(2) phases will precipitate. Following work on Al-Mg-X alloys, it is possible that TMP at such temperatures might promote intragranular formation of these phases and promote microstructural refinement during recrystallization. Microstructural analyses reveal that the T(2) phase in Al 2090 may play a similar role to the beta-phase in Al-Mg-X alloys during microstructural evolution. Mechanical property data indicate that Al 2090 can be moderately (215-245 percent) superplastic at 370 C following processing at 300 C.
The purpose of this effort is to develop low-cost rapid forming superplastic aluminum that will be evaluated in pilot production trials for automotive SPF components. The alloy development study conducted under SPITFIRE-1 showed that the addition of CU or Mn to the base 5083 aluminum alloy refined the grain size, leading to enhanced superplastic properties. In SPITFIRE-2, these alloy variants will be further refined and studied to meet the target properties established earlier in the program. Mechanical properties, component forming and post-forming properties will be evaluated. Also, the alloy production process, including thermomechanical processing (TMP) optimization to reduce production cost, will be investigated during SPITFIRE-2. After identifying preferred compositions and production processing, the most promising alloy will be manufactured into production coils for verification during SPITFIRE-3. Components will be produced from these coils in SPITFIRE-4, and the process and component performance will be assessed.
NASA, DoD, DHS, and commercial industry have a need for miniaturized, rugged, low-cost vacuum systems. Recent advances in sensor technology have led to the development of very small mass spectrometer detectors as well as other miniature analytical instruments. However, the vacuum systems to support these sensors remain large, heavy, and power-hungry. To meet this need, a miniaturized vacuum system was created based on a very small, rugged, and inexpensive- to-manufacture molecular drag pump (MDP). The MDP is enabled by the development of a miniature, veryhigh- speed, rugged, low-power, brushless DC motor optimized for wide temperature operation and long life. Such a pump represents an order-of-magnitude reduction in mass, volume, and cost over current, commercially available, state-ofthe- art vacuum pumps. The vacuum system consists of the MDP coupled to a ruggedized rough pump (for terrestrial applications or for planets with substantial atmospheres). The rotor in the MDP consists of a simple smooth cylinder of aluminum spinning at approximately 200,000 RPM inside an outer stator housing. The pump stator comprises a cylindrical aluminum housing with one or more specially designed grooves that serve as flow channels. To minimize the length of the pump, the gas is forced down the flow channels of the outer stator to the base of the pump. The gas is then turned and pulled toward the top through a second set of channels cut into an inner stator housing that surrounds the motor. The compressed gas then flows down channels in the motor housing to the exhaust port of the pump. The exhaust port of the pump is connected to a diaphragm or scroll pump. This pump delivers very high performance in a very small envelope. The design was simplified so that a smaller compression ratio, easier manufacturing process, and enhanced ruggedness can be achieved at the lowest possible cost. The machining of the rotor and stators is very simple compared to that necessary to fabricate TMP (turbo molecular pump) rotor and stator blades. Also, the symmetry of the rotor is such that dynamic balancing of the rotor is greatly simplified. Finally, because of the simplified design, the number of parts in the unit is cut by nearly a factor of three. In fact, there are only five parts, not counting the motor and off-the-shelf screws and O-rings. This reduces the amount of machining and also makes fit-up much simpler while allowing the maintenance of close tolerances.