SEARCH · Search NASA

Results for “Toolpath”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

3 records

All sources NASA NTRS DOE OSTI

NASA NTRS2013

Neutron Characterization for Additive Manufacturing

Oak Ridge National Laboratory (ORNL) is leveraging decades of experience in neutron characterization of advanced materials together with resources such as the Spallation Neutron Source (SNS) and the High Flux Isotope Reactor (HFIR) shown in Fig. 1 to solve challenging problems in additive manufacturing (AM). Additive manufacturing, or three-dimensional (3-D) printing, is a rapidly maturing technology wherein components are built by selectively adding feedstock material at locations specified by a computer model. The majority of these technologies use thermally driven phase change mechanisms to convert the feedstock into functioning material. As the molten material cools and solidifies, the component is subjected to significant thermal gradients, generating significant internal stresses throughout the part (Fig. 2). As layers are added, inherent residual stresses cause warping and distortions that lead to geometrical differences between the final part and the original computer generated design. This effect also limits geometries that can be fabricated using AM, such as thin-walled, high-aspect- ratio, and overhanging structures. Distortion may be minimized by intelligent toolpath planning or strategic placement of support structures, but these approaches are not well understood and often "Edisonian" in nature. Residual stresses can also impact component performance during operation. For example, in a thermally cycled environment such as a high-pressure turbine engine, residual stresses can cause components to distort unpredictably. Different thermal treatments on as-fabricated AM components have been used to minimize residual stress, but components still retain a nonhomogeneous stress state and/or demonstrate a relaxation-derived geometric distortion. Industry, federal laboratory, and university collaboration is needed to address these challenges and enable the U.S. to compete in the global market. Work is currently being conducted on AM technologies at the ORNL Manufacturing Demonstration Facility (MDF) sponsored by the DOE's Advanced Manufacturing Office. The MDF is focusing on R&D of both metal and polymer AM pertaining to in-situ process monitoring and closed-loop controls; implementation of advanced materials in AM technologies; and demonstration, characterization, and optimization of next-generation technologies. ORNL is working directly with industry partners to leverage world-leading facilities in fields such as high performance computing, advanced materials characterization, and neutron sciences to solve fundamental challenges in advanced manufacturing. Specifically, MDF is leveraging two of the world's most advanced neutron facilities, the HFIR and SNS, to characterize additive manufactured components.

Watkins, Thomas↗

NASA NTRSDate not supplied

Windform® XT 2.0 Use as 3U CubeSat Primary Structure

CubeSats provide a platform for small-scale space research and technology demonstration at reduced complexity, cost, and development time. These advantages drove the NASA Langley Research Center (LaRC) to develop and launch the GPX2 3U CubeSat to explore the viability of using Commercial Off-The-Shelf (COTS) differential GPS (dGPS) in low earth orbit. To reduce manufacturing costs and increase design flexibility, the project chose additive manufactured Windform® XT 2.0 as the primary bus material rather than traditional subtractive manufactured (milled) metal. The bus is a two-part, Selective Laser Sintered, 3D-print structure consisting of a single-piece, five-walled chassis and single-walled cover. The bus was specially designed to allow the project to accommodate the payload electronics stack as well as antennas, receivers, and deployable mechanisms. By using an additive manufactured solution, LaRC was able to design in features unrealizable through traditional milling, with a lead-time of roughly two weeks. In comparison, traditional subtractive manufacturing limits geometry options due to toolpath reach and bus construction would have required multiple components for each wall. This would have resulted in a more costly, longer lead-time article with more joints, fasteners, and complexity with a commensurate increase in overall mass. A number of lessons-learned were captured during the design, analysis, and testing of the GPX2 CubeSat covering thermal and structural analysis, vibration modeling, and geometric tolerancing. Additionally, a variety of material testing and verification were performed before and during spacecraft design and integration to assure the suitability of Windform® XT 2.0 for the launch and mission environments. This article provides the highlights of designing and testing the GPX2 bus.

CubeSat↗

NASA NTRSDate not supplied

Cold Metal Transfer (CMT) Wire-Arc Additive Manufacturing (WAAM)

Aluminum has been identified as a compound within regolith and is likely to become a core component of our infrastructure on the lunar surface as in-situ resource utilization (ISRU) capabilities are advanced Large-scale components, outfitting, and repairs of aluminum materials can be fabricated with robotic wire arc additive manufacturing (WAAM) in order to inhabit the moon’s surface long term WAAM is a high value process for lunar advanced manufacturing as it does not require special containment to reduce explosion hazards such as powder-based additive processes and feedstock The welding process of cold metal transfer (CMT) is a relatively new variation of gas metal arc welding (GMAW, also known as MIG) that relies on the detection of a short circuit in the welding process to control the deposition droplet action, resulting in lower heat input and splatter compared to conventional MIG welding The past year was spent developing the CMT-WAAM process for aluminum materials, tested specialty feedstock, tested within the high vacuum environment, and advanced the MSFC capability to perform complex toolpathing from solid models Upcoming and future work includes large depositions working towards material certification for multiple feedstocks, in-situ monitoring, work to use recycled materials for the AM feedstock, and the design and fabrication of a parabolic flight experiment payload.

cold metal transfer↗