Search NASA⌕ Search

SEARCH · Search NASA

Results for “Transportation consideration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

TRANSPORTATION CONSIDERATIONS FOR USED FUEL AND ADVANCED NUCLEAR ENERGY TECHNOLOGIES

This study focuses on requirements and challenges pertaining to advanced transportable nuclear energy systems, which are currently in development and feature varying degrees of mobility. These reactors mostly use high-assay low-enriched uranium (HALEU) fuel, and only limited refueling is required during their lifecycles. Due to the smaller source terms, higher burnup fuel, and potentially higher thermal efficiency involved, the waste inventory will be less than that generated by conventional light-water reactors. However, the relevant regulatory requirements must be met when transporting HALEU fuel (whether fresh or used) inside the reactor vessel—mainly the fuel material transportation, siting, and physical protection requirements outlined in US Nuclear Regulatory Commission (NRC) regulations 10 CFR 71 and 73. Spent nuclear fuel (SNF), as well as irradiated fuel (used during any interval of reactor operation), contains highly radioactive materials that generate heat and necessitate special precautions during transportation. This study addresses the challenges that this incurs, and outlines potential solutions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

TRANSPORTATION CONSIDERATIONS FOR USED FUEL AND ADVANCED NUCLEAR ENERGY TECHNOLOGIES

This study focuses on requirements and challenges pertaining to advanced transportable nuclear energy systems, which are currently in development and feature varying degrees of mobility. These reactors mostly use high-assay low-enriched uranium (HALEU) fuel, and only limited refueling is required during their lifecycles. Due to the smaller source terms, higher burnup fuel, and potentially higher thermal efficiency involved, the waste inventory will be less than that generated by conventional light-water reactors. However, the relevant regulatory requirements must be met when transporting HALEU fuel (whether fresh or used) inside the reactor vessel—mainly the fuel material transportation, siting, and physical protection requirements outlined in US Nuclear Regulatory Commission (NRC) regulations 10 CFR 71 and 73. Spent nuclear fuel (SNF), as well as irradiated fuel (used during any interval of reactor operation), contains highly radioactive materials that generate heat and necessitate special precautions during transportation. This study addresses the challenges that this incurs, and outlines potential solutions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Models for Incorporating Equity in Transportation Electrification Considerations for Public Utility Regulators, An addendum to the NARUC report, Electric Vehicles: Key Trends, Issues, and Considerations for State Regulators

Momentum for the electric vehicle (EV) transition is well underway, and the utility sector plays an important role in supporting its success. For frontline communities, the transition offers a promising solution to improve environmental and public health outcomes, economic development, affordability, and transit equity. However, the transition will need to involve care and intention to ensure that the needs of underserved communities are prioritized throughout the planning, decision-making, and implementation processes. States have taken the lead in some cases, as profiled in Box 6. Whether driven by state commissions or utilities themselves, utilities have a range of options available to ensure equity is central in their transportation electrification plans and programs by drawing from a variety of existing and emerging experiences, as summarized in Table 1.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

Models for Incorporating Equity in Transportation Electrification Considerations for Public Utility Regulators, An addendum to the NARUC report, Electric Vehicles: Key Trends, Issues, and Considerations for State Regulators (2019)

Momentum for the electric vehicle (EV) transition is well underway, and the utility sector plays an important role in supporting its success. For frontline communities, the transition offers a promising solution to improve environmental and public health outcomes, economic development, affordability, and transit equity. However, the transition will need to involve care and intention to ensure that the needs of underserved communities are prioritized throughout the planning, decision-making, and implementation processes. States have taken the lead in some cases, as profiled in Box 6. Whether driven by state commissions or utilities themselves, utilities have a range of options available to ensure equity is central in their transportation electrification plans and programs by drawing from a variety of existing and emerging experiences, as summarized in Table 1.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

Highly Reversible Sodium Metal Battery Anodes via Alloying Heterointerfaces

As a promising pathway toward low-cost, long-duration energy storage, rechargeable sodium batteries are of increasing interest. Batteries that incorporate metallic sodium as anode promise a high theoretical specific capacity of 1166 mAh g –1 , and low reduction potential of –2.71 V. The high reactivity and poor electrochemical reversibility of sodium anodes render sodium metal anode (SMA) cells among the most challenging for practical implementation. Here, the failure mechanisms of Na anodes are investigated and the authors report that loss of morphological control is not the fundamental cause of failure. Rather, it is the inherently poor anchoring/root structure of electrodeposited Na to the electrode substrate that leads to poor reversibility and cell failure. Poorly anchored Na deposits are prone to break away from the current collector, producing orphaning and poor anode utilization. Thin metallic coatings in a range of chemistries are proposed and evaluated as SMA substrates. Based on thermodynamic and ion transport considerations, such substrates undergo reversible alloying reactions with Na and are hypothesized to promote good root growth—regardless of the morphology. Among the various options, Au stands out for its ability to support long Na anode lifetime and high reversibility (Coulombic Efficiency > 98%), for coating thicknesses in the range of 10–1000 nm. Finally, as a first step toward evaluating practical utility of the anodes, their performance in Na||SPAN cells with N:P ratio close to 1:1 is evaluated.

25 ENERGY STORAGE↗
DOE OSTI2023

Numerical investigations to identify environmental factors for field-scale reactive transport of pathogens at riverbank filtration sites

While induced bank filtration is a proven method for facilitating sustainable drinking water production, it is at risk from surface water contaminations (e.g., pathogens). Induced bank filtration and pathogen transport in groundwater have been studied extensively. However, long-term studies that consider real-world conditions are missing. These conditions include seasonal changes to environmental conditions and waterworks operations. Therefore, to analyze the effect of seasonal changes on the transport of human pathogenic viruses and their indicators in induced bank filtration, concentrations of adenoviruses and pathogen indicators were monitored over 16 months at an active bank filtration plant at the Rhine River, in Düsseldorf (Germany). Based on this data, a 2D groundwater model was created in PFLOTRAN that simulated flow, heat transport, conservative transport of chloride and the resulting electrical conductivity, reactive transport of oxygen and nitrate, and colloid-based transport of coliforms, somatic coliphages, and adenoviruses. The results show that reduced travel time was the key factor determining periods with a low removal of coliforms and somatic coliphages in the aquifer. Travel time was controlled by river level variations during rainy seasons, and the waterworks extraction rates during dry seasons. Further, for adenovirus transport, travel distance in the subsurface appeared to be the key factor, while travel time had no significant impact. Coliform removal increased when the colmation layer permeability decreased, while coliphage and adenovirus removal was unaffected by the colmation layer permeability. Seasonal changes in temperature and oxygen content did not significantly impact the removal of coliphages and adenoviruses in groundwater. Denitrifying conditions correlated with a lowered coliform removal, but the modelling could not establish a connection between denitrifying conditions and coliform removal. Our study showed that removal of pathogens and pathogen indicators at induced bank filtration plants varies greatly in time and space (e.g., for coliforms from 1 to 4 log-levels at 20m travel distance), and that adenovirus transport differs considerably from transport of coliforms and somatic coliphages.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Uranium Oxide Elutriation at Higher Flow Rates and Longer Times

This work supports the recovery of high-assay low-enriched uranium (i.e., U enriched in 235 U to >5% and <20%) from used nuclear fuel. One step includes elutriating triuranium octoxide (U 3 O 8 ) from a fluidized bed of alumina (Al 2 O 3 ) that fills the main reaction chamber. The experiments outlined in this report assessed the effects of the time and flow rate on the elutriation of U 3 O 8 powder from the reaction vessel. Testing at Oak Ridge National Laboratory (ORNL) was performed in a one-fourth scale experimental apparatus based on a pilot-scale system, which is the Material Recovery Pilot Plant (MRPP) at Idaho National Laboratory (INL). The experimental system comprises a supply of pressurized nitrogen (N 2 ), a gas heater, the reaction vessel, a knock-out pot, and a water trap where elutriated particles are collected for sampling. An Al 2 O 3 fluidized bed is contained within the reaction vessel. A bed of Al 2 O 3 with a nominal size of 180 µm and U 3 O 8 with a nominal size of 7 µm was fluidized at 2 different flow rates so the U 3 O 8 physically separated from the bed. The apparatus was simple and had no valves or sharp bends downstream from the reactor. The flow exited the reactor through a side port at the top. The flow passed through a knock-out vessel before the flow was passed through a bubbler to capture the U 3 O 8 . Seven tests were completed with U 3 O 8 using an elutriating gas of N 2 heated to 200°C. Tests were performed with bed loadings that comprise 25.0 g of U 3 O 8 , or 3.6 wt% of the bed mass. Except for one test performed at 12 SLPM, the gas flow rate through the bed for the other experiments was set at 10 SLPM as measured by the mass flow meter. Linear velocities through the bed were calculated as 28 and 34 cm/s, or 0.9 and 1.1 ft·s -1 . The duration of the tests ranged from 20 to 180 min, and one test had a flow cycled between 0 and 5 SLPM every 5 min for 40 min. The testing successfully demonstrated elutriation of U 3 O 8 from the fluidized bed as up to a 100% of the U 3 O 8 was transferred out of the bed. The removal of U 3 O 8 had a logarithmic dependence on flow rate. The design changes made the apparatus easier to clean, and the mass balances were better than those used in previous studies. Some elutriated Al 2 O 3 collected in the tubing that connected the reactor to the knock-out pot, but the amount of Al 2 O 3 was minimal for 10 SLPM. The flow at 12 SLPM showed considerable transport of Al 2 O 3 bed material into the reaction-vessel headspace and the transfer line to the knock-out pot.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

A Subcritical Assembly for Training and Education Use at the Oak Ridge National Laboratory [Slides]

Sufficient AGN-201M fuel plate material exists at Y-12 to support the development of a new, inherently safe, subcritical assembly for use in NCS training courses at ORNL. Four experiments with the ORNL subcritical assembly are possible and feasible. Future work includes the final design of the core and reflector and split table component design specifications. The ORNL Material Demonstration Facility (MDF) may be used to 3D print ORSA stand/table components and graphite reflector. Researchers will consider fuel coatings for contamination control, rather than an Al can. A visit to Y-12 will be made to determine the location of AGN fuel plates and remaining fuel transportation considerations. Final facility location will be considered

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Numerical design considerations for vapor transport deposition of metal-halide perovskite thin films

While metal-halide perovskites (MHPs) offer high efficiency and potential application in single junction and tandem solar cells, challenges remain in translating solution-based methods to commercial-scale production. Vapor transport deposition (VTD) offers advantages such as precise control over film composition and purity, as well as the possibility of achieving high thin film deposition rates for scale-up. In this work, a numerical model is developed to simulate the deposition process, analyzing the impact of parameters including source material temperature, carrier gas and dilution gas flow rates, and chamber pressure to optimize deposition rates and film uniformity. Geometrical parameters, such as throw distance, are also found to significantly affect rate and uniformity. Furthermore, the modeling results presented here offer valuable insight for improving the scalability of VTD for the processing of metal-halide perovskites.

Chemical vapor deposition↗
DOE OSTI2026

Primary Heat Transport System Design Considerations for Xcimer Energy’s Athena Fusion Pilot Plant

Fusion energy promises a reliable, carbon-free source of power; however, significant challenges remain before it can be deployed as an economical energy source. In addition to achieving fusion conditions, power plants must operate under extreme temperatures, radiation, and mechanical loads while maintaining high efficiency and availability. These requirements place strong demands on engineering design and plant operation. This work focuses on the engineering challenges associated with balance of plant analysis for inertial fusion energy systems. In particular, this paper examines the design considerations for primary heat transfer systems in fusion pilot plants employing molten fluoride salt coolants, with particular emphasis on system layout optimization and the balance between competing design objectives using the Xcimer Energy Athena inertial pilot plant design as a case study. Through systematic analysis of candidate system configurations and parametric sensitivity studies, we identify key engineering trade-offs governing salt inventory, pumping power requirements, and operational flexibility. The analysis employs system-level modeling tools to explore the design space and establish relationships between geometric parameters and system performance metrics.

Greenwood, Scott [ORNL] (ORCID:0000000333480736)↗
DOE OSTI2026

Challenges and Considerations for Rural Transportation: Stakeholder Perspectives

This fact sheet presents key findings and challenges identified by stakeholders through an initiative supported by the U.S. Department of Energy's Communities Local Energy Action Program (Communities LEAP). The project engaged community stakeholders, fleet operators, and local officials across ten rural counties in western Alabama to explore opportunities for expanding access to alternative transportation fuels. Guided by a regional coalition and supported by the National Laboratory of the Rockies (NLR), the effort emphasized challenges and related potential technical solutions. The fact sheet highlights transportation priorities identified by participants, outlines barriers unique to rural contexts, and summarizes resources developed by NLR subject matter experts to help local entities address these challenges.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2020

ElectroMon Geometry Considerations: Simulations of Electron Transport to a Diamond-Based Detector

Particle-in-Cell simulations were performed to investigate the effects of electrode bias and pitch on the expected number of electrons arriving at a diamond-based detector at a set of relevant incident electron energies for electron cloud monitoring. Results of these simulations indicate that the pitch of the electrodes directly impacts the number of incident electrons based on complete opacity of the electrodes to the electrons; image charge does not play a role at any relevant electron energy. Positive bias on the incident electrodes directly increases the energy of the incident electrons, while negative bias reduces the energy and completely repels incoming electrons of energies lower than the applied bias. These results are intended to be used as input parameters for a solid-state simulation which will determine the collection efficiency of the electron-hole pairs produced within the diamond as a function of position and energy.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Systemwide Considerations for Electrification of Transportation in Islands and Remote Locations

Electric vehicles (EVs) represent an important socio-economic development opportunity for islands and remote locations because they can lead to reduced fuel imports, electricity storage, grid services, and environmental and health benefits. This paper presents an overview of opportunities, challenges, and examples of EVs in islands and remote power systems, and is meant to provide background to researchers, utilities, energy offices, and other stakeholders interested in the impacts of electrification of transportation. The impact of uncontrolled EV charging on the electric grid operation is discussed, as well as several mitigation strategies. Of particular importance in many islands and remote systems is taking advantage of local resources by combining renewable energy and EV charging. Policy and economic issues are presented, with emphasis on the need for an overarching energy policy to guide the strategies for EVs growth. The key conclusion of this paper is that an orderly transition to EVs, one that maximizes benefits while addressing the challenges, requires careful analysis and comprehensive planning.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Technical Information Needs and Regulatory Considerations for Front-End Transportation Activities of HALEU Fuel Feed Material

This report fulfills task order number 31310022F0033 Task 1 Assessment of technical information needs and considerations for front-end transportation activities for HALEU fuel feed material. This assessment primarily focuses on the transportation outlook and packaging requirements for transporting high-assay low-enriched uranium (HALEU) fuel feed material. The regulatory framework is described in section 3.0. In section 4.0 the specific issues associated with reviewing HALEU feed material packages are discussed. The rest of the report discusses the need for new packages and Department of Energy progress on HALEU production. Through this evaluation it is shown that the 5% enrichment barrier between low-enriched uranium and HALEU is a significant challenge to transportation packaging. However, there are licensed designs and concepts that can be used to transport HALEU feedstock. No significant issues were identified through the HALEU range up to 20% enriched.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Robot-based Additive Manufacturing of Lego-type Modular Molds for Wind Blades

The objective of this project is to reduce the cost and lead time of horizontal wind turbine blade mold tooling and blade transportation, while maintaining the highest standards of blade quality. The solution involves a smart-design family of modular molds that are easily transportable to fabrication sites near the place of service. Key innovations include the use of additive manufacturing (AM) to integrate conformal thermal management channels, offering enhanced control over the thermal profiles tailored to specific blade materials. This approach enables in-situ quality assurance during mold fabrication, significantly improves mold life, and allows for reuse across multiple production cycles. Ultimately, the solution aims to optimize both tooling and transportation costs, contributing to the scalability of wind turbine blade production. A significant barrier to scaling up the production of large wind turbine blades lies in the high costs associated with tooling and the transportation of blades. Traditional molds are expensive, bulky, and difficult to transport, adding considerable lead time and cost to the overall manufacturing process. Additionally, transporting blades to distant locations for final assembly further exacerbates these challenges. The project aims to address these inefficiencies by demonstrating a modularized, additive-manufactured mold that meets all necessary blade specification requirements, specifically for blade lengths between 120m and 150m.

17 WIND ENERGY↗
DOE OSTI2025

Future marine biofuels in the port of Seattle region

Marine transportation, a vital global sector, emits 3% of global annual greenhouse gas emissions, which are predicted to increase in the future. Marine biofuels derived from biomass or waste sources like wood residue, waste oil and municipal solid waste can be used for decarbonization. However, limited studies have explored if sufficient marine biofuels could be produced and supplied to major regional ports given feedstock, supply chain and technological constraints. We fill this gap by evaluating the feasibility of supplying marine biofuels to the Port of Seattle. The Regional Bio-Economy Model (RBEM) and the Freight and Fuel Transportation Optimization Tool (FTOT) are used to build scenarios for simulating marine biofuel production in the Port region. We harmonized technoeconomic assumptions for RBEM and FTOT, input FTOT feedstock utilization and routing outputs into RBEM, and modelled conversion, feedstock, and policy scenario variations in RBEM. In RBEM, overall biofuel production was constrained primarily by the biofuel cost, and then by feedstock availability. Providing policy incentives and reducing permitting time frames alleviated these constraints and spurred the buildout of a robust industry through industrial learning dynamics in the initial years. With these measures in place, the RBEM results show that 100% of fuel demand at the Port can be supplied by biofuels with policy incentives and suitable technoeconomic conditions, but the addition of transportation cost considerations using FTOT led to 27.8% of demand being able to be met by biofuels at reasonable fuel delivery cost.

09 BIOMASS FUELS↗