Search NASA⌕ Search

SEARCH · Search NASA

Results for “U-Mo fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Porosity, swelling, and composition evolution in high-burnup monolithic U-Mo fuel

The microstructural progression of very high-burnup (>8 × 10 21 fissions/cm 3 ) monolithic uranium-molybdenum (U-10wt.%Mo) was analyzed, providing crucial insights into the behavior of post-recrystallized nuclear fuel, where scant data exists. Three focused ion beam cuboids sourced from a fuel plate with varying local burnups of 8.86 × 10 21 , 9.05 × 10 21 , and 9.36 × 10 21 fissions/cm 3 were characterized. The porosity and composition of the samples were evaluated to characterize the evolution of the microstructure as a function of fission density and different locations on the fuel plate, while simultaneously isolating plate-specific parameters such as Zr diffusion barrier thickness, hot-isostatic-pressing conditions, enrichment, and reactor conditions. The porosity was segmented, and the three-dimensional distribution of the porosity was extrapolated from the two-dimensional segmentation. The composition was assessed and quantified using energy-dispersive X-ray spectroscopy areal mapping. The porosity fraction increased as a function of the burnup from 27.77±0.51, 35.12±1.54, and 37.71±0.44 % for 8.86 × 10 21 , 9.05 × 10 21 , and 9.36 × 10 21 fissions/cm 3 , respectively. When compared to literature, the porosity volume fraction plateaus at burnups greater than 6 × 10 21 fissions/cm 3 , while the pore size grows linearly as a function of fission density. The number of large pores increased in number density as a function of burnup, while the smallest pores (<0.3 µm) increased up to 9.05 × 10 21 fissions/cm 3 , followed by a decrease at 9.36 × 10 21 fissions/cm 3 . The delamination and cracking in the fuel plate propagated through an interconnected porosity sublayer identified ∼5 µm from the diffusion barrier. The local swelling of the specimens was within or near the prediction bounds of the Robinson-Williams model for local swelling. The fission products, strontium, barium, cerium, and cesium, precipitated into the pores, while neodymium accumulated adjacent to the pores. Furthermore, these findings have direct implications for the development of fuel performance codes and the accurate documentation of the microstructure evolution in high burnup U-Mo, thus enhancing the safety and efficiency of nuclear fuel usage.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

A Critical Review on the History of Fabricating Monolithic U-Mo Fuel Plates

Fabrication of uranium-molybdenum alloy fuels has been occurring since the early 2000s in support of the development of a high-uranium-density low-enrichment fuel for use in high-performance research and test reactors which operate at relatively low temperatures. The primary fuel form—a thin foil of uranium, alloyed with 10wt% molybdenum, which is coated in a layer of zirconium and then encapsulated with aluminum 6061 as a cladding material—was developed over a number of years.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

A critical review of the history of fabricating monolithic U-Mo fuel plates

The fabrication of monolithic uranium-molybdenum alloy fuels, specifically those developed for high-performance research and test reactors, began in the early 2000s. The primary fuel form consists of uranium alloyed with 10-wt% molybdenum in a thin foil coated with zirconium and encapsulated in aluminum-6061 cladding. Over the years, the process has evolved with different types of casting, heat treatments, rolling schedules, and cladding applications. This review examines the history of these fabrication processes and their impact on microstructure and fuel-swelling performance. Even though various fabrication methods were used, we found little correlation between fabrication variation and fuel swelling. This insensitive relationship between fabrication variation and fuel swelling is primarily due to inhomogeneous microstructures that formed during casting and grain refinement that occurred during rolling. We conclude that the fabrication processes we examined produced similar microstructures, indicating that the fuel microstructure is somewhat insensitive to the fabrication parameters evaluated. However, the relatively small amount of historic data, such as those for grain sizes, limited this analysis. More recently fabricated materials, such as those from ongoing irradiation experiment, Mini-Plate-1 and Mini-Plate-2, were also excluded from this analysis and are intended to be reviewed separately. The findings, that fuel microstructure is somewhat insensitive to the fabrication parameters, do not imply that any fabrication method is acceptable, given the uncertainties in data and fuel-swelling observations. For example, only arc melting and vacuum induction melting casting processes were previously explored in the historic fabrication efforts. In conclusion, the findings should not be extrapolated to other casting processes.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Effects of ZrN Coating and Heat Treatment on U-Mo Dispersion Fuel under Irradiation

The stability of U-Mo fuel particles in Al matrix can be improved using ZrN coating and heat treatment. This study investigated irradiation behaviors of fuel plates containing U-Mo fuel particles fabricated with different conditions including heat treatment and the thickness of ZrN coating. Additionally, different fission densities were applied to each fuel plate to understand how varying fission densities affect its irradiation behaviors. This study showed that more recrystallization of grains and development of high burnup structure (HBS) occurred in irradiated fuel particles with higher fission densities. Heat treatment reduced the accumulation of fission gas bubbles in the fuel particles by coarsening their grains. The fuel particles with a ZrN coating thickness of 1.2-1.8 µm showed less significant development of U-Mo/Al interaction layers than the particles with a coating thickness of 0.5 µm after irradiation. This might indicate the existence of a critical thickness of ZrN coating to minimize the formation of the interaction layers. Fission gas bubbles were observed at grain boundaries of irradiated U-Mo fuel particles at low fission densities, and the formation of dendritic features with a darker contrast was identified in backscattered electron images. These features stemmed from grain boundaries with fission gas bubbles or HBS, and some of them contained the bubbles, indicating that they might represent an early stage of HBS propagation in the fuel particles.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Effects of ZrN coating and heat treatment on U-Mo dispersion fuel systems under irradiation

The stability of U-Mo fuel particles embedded in an Al matrix under irradiation can be enhanced through ZrN coatings and/or heat treatment. Here, the present study investigates the irradiation behavior of fuel plates containing U-Mo fuel particles fabricated under various heat-treatment conditions and ZrN coating thicknesses. Different fission densities were also applied to each fuel plate to evaluate the effects of these variables. Results indicate that higher fission densities lead to more grain recrystallization and high burnup structure (HBS) development in the fuel particles. Heat treatment was found to mitigate the accumulation of fission gas bubbles in fuel particles at low fission densities by coarsening their grains. Fuel particles with ZrN coatings of a 1.2 μm thickness or above exhibited reduced formation of U-Mo/Al interaction layers, suggesting the existence of a critical ZrN coating thickness that minimizes the development of these layers. Fission gas bubbles were predominantly observed at grain boundaries of U-Mo fuel particles irradiated at low fission densities. Subgrain boundaries, which appeared to originate from the original grain boundaries containing fission gas bubbles or HBSs, were also observed, indicating the early stage of HBS propagation in the fuel particles.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Mapping the Microstructure During the Historic U-Mo Monolithic Fuel Foil Fabrication Process

Since 2004, there has been extensive effort towards the development of a uranium molybdenum monolithic fuel system to convert high performance research and test reactors. The RERTR-6 experiment was the first to attempt a monolithic fuel instead of a dispersed fuel form. The fabrication methods evolved overtime and provided the basis for current fabrication methods. The various steps in the process inevitably tailor the fuel alloy microstructure which is known to influence irradiation behavior. This document aims to present and discuss the fabrication evolution that transpired through a recounting of historical data from the various fabrication campaigns. By overlaying this data with basic science studies on the U-Mo that explored transformation kinetics, it is possible to estimate a measure of the impact heat treatments have on the final as-fabricated microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Impact of chemical ordering on thermodynamic properties of point defects and Xe substitutional in U-10Mo

The accurate knowledge of defect energetics is critical to understanding the aging and irradiation behavior of U-10Mo nuclear fuel, which is selected as the fuel type for conversion of the United States High-Performance Research Reactors (HPRRs). Furthermore, using hybrid molecular dynamics and Monte Carlo (MDMC) simulation, we studied the impact of chemical ordering on the formation energies of vacancies, interstitials, and the solution energy of the Xe substitutionals. Instead of forming a random solid solution (RSS), substantial short-range-order (SRO) develops in U-10Mo, particularly at low temperatures. Mo atoms are found to repel each other and prefer U-rich local atomic environments within the 1st nearest neighbor (1NN) cutoff. Compared to the case of a RSS, the state with equilibrated Mo ordering shifts the distributions of vacancy and interstitial formation energies due to the dependence of defect energies on the local atomic environment, without a clear effect on Xe solution energy. In the operation temperature range (100–250 °C) of U-Mo fuels, neglecting SRO can lead to an inaccurate estimate of thermal equilibrium point defect concentrations by over an order of magnitude and incorrectly predict the preference among different types of dumbbells, highlighting the critical importance of accounting for the impact of chemical ordering for accurate atomistic calculations of defect properties.

Molecular dynamics and Monte Carlo (MDMC)↗
DOE OSTI2024

Assessment of effective elastic constants of U-10Mo fuel: A multiscale modeling and homogenization study

The significant microstructural changes that U-Mo fuel undergoes during operation degrades its mechanical properties and structural integrity. Microstructural evolution entails the formation, evolution, and redistribution of porosity in conjunction with grain refinement. In the present paper, we employ numerical approaches to assess the impact of the various microstructural features—grains, nanoscale intragranular fission gas bubbles, and mesoscale intergranular voids—on the degradation of elastic constants. Phase-field microstructure models are combined with the asymptotic expansion homogenization technique in order to derive the effective elastic constants as a function of porosity and fission density. Here the results are verified and compared against theoretical bounds. Using this approach, elastic degradation in operating nuclear fuels can be quantified when the distributions of microstructural features are known.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Purification of U from U-10Mo scrap generated during the fabrication of high performance research reactor fuel

A low enriched U-Mo alloy fuel is under development to replace highly enriched U fuels currently used in United States high performance research reactors. The alloy casting and fuel fabrication processes will generate scrap streams containing low enriched U (LEU) which must be recovered. Solvent extraction processes were designed using the Argonne Model for Universal Solvent Extraction (AMUSE) to purify solutions containing 20 and 50 g/L U. The feed for the solvent extraction processes was prepared from solutions generated from the dissolution of U-10Mo-Zr foils and U-10Mo-Zr-Al mini-plates. The U purification processes were demonstrated using two, 16-stage banks of miniature mixer-settlers. The solvent extraction experiments demonstrated that all design objectives for the U purification processes could be met. The U recovery in the product stream for each flowsheet was ≥99.9%. The flowsheet demonstrations also showed that the purity of the U Product will meet the requirements of the ASTM International C1462-21 specification for LEU metal enriched to less than 20% 235 U. In conclusion, the AMUSE modeling for both flowsheet demonstrations was validated by comparing predicted and measured concentrations of U, Mo, and Zr in the exit streams and stage samples at steady-state conditions in the mixer-settlers.

modified PUREX process↗
DOE OSTI2025

Microstructurally validated stable and predictable swelling in low-enriched uranium monolithic U-10Mo fuel mini-plates

Qualification of the low-enriched uranium (LEU) monolithic U-10 wt%Mo (U-10Mo) plate-type fuel system requires a demonstration of a stable and predictable fuel swelling behavior over the anticipated operating conditions of the United States high-performance research reactors (USHPRRs) selected for conversion to LEU operation. This will allow each reactor to develop appropriate safety margins that will retain fuel element lifetime coolability. Additionally, the fuel system must maintain performance attributes when fabricated at a commercial scale. The Mini-plate 1 experiment represents the first irradiation test of commercially fabricated miniaturized monolithic LEU U-10Mo fuel plates. Here, the swelling behavior within this experiment was compared against that of historical fuel developmental tests to reveal that the commercially fabricated fuel performed within the current recommended U-10Mo swelling model's predictions. Additionally, the fuel microstructural evolution was evaluated to link initial conditions to subtle variations detected in the swelling response, providing validation and confidence that the fuel system is robust.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Thermal conductivity measurement of U-Mo and U-Mo/Al interaction layers generated from in-pile irradiation using the suspended-bridge method

Here, this study presents the first measurement of the individual thermal conductivity of U-7wt.%Mo fuel particles and U-Mo/Al interaction layers (ILs) from in-pile irradiated dispersion fuel plates, using the suspended-bridge method. Nanorods of U-7wt.%Mo fuel and U-Mo/Al ILs were extracted by focused ion beam (FIB), and their microstructures were characterized with transmission electron microscopy (TEM). TEM revealed finely distributed nanobubbles in the U-7wt.%Mo matrix, along with an amorphous structure in the ILs. The thermal conductivity of in-pile irradiated U-7wt.%Mo was approximately 30% lower than that of the unirradiated material, ranging from 6.7 W/m·K at 300 K to 8.5 W/m·K at 380 K. The ILs exhibited even lower thermal conductivity, from 2.1 W/m·K at 300 K to 2.7 W/m·K at 380 K. These reductions, attributed to nanobubbles, fission products, and irradiation-induced point defects, were analyzed through a combination of microstructural characterization and literature-based transport models, which successfully reproduced the observed degradation trends.

42 - ENGINEERING↗
DOE OSTI2024

Formation of uranium nitride nanoparticles via mechanical alloying of uranium-molybdenum alloy fuels in gaseous nitrogen

Uranium-molybdenum (U-Mo) alloys show promise as a nuclear fuel system due to their high thermal conductivity and fuel loading capability. However, U-Mo systems are susceptible to irradiation induced swelling ultimately affecting the cladding via mechanical and chemical interactions. To address these shortcomings, this research investigated the formation of uranium mononitride (UN) nanoparticles within a 90 wt% U/10 wt% Mo (U-10Mo) matrix to act as a prospective defect sink for fission products at nanometric hetero-interfaces. To promote the formation of UN, U-10Mo powders were mechanically alloyed under a high purity nitrogen atmosphere. Variations of the milling process investigated included media size, duration of milling, and number of times the milling jar was re-aerated with nitrogen gas. Characterization of the fuel microstructure was completed using light element analysis, X-ray diffraction, scanning and transmission-electron microscopy, electron energy loss spectroscopy, and atom probe tomography. UN nanoparticles measuring 1–5 nm in radius were observed in the U-Mo matrix as early as 1 h into the mechanical alloying process. Milling time in excess of 10 h was found to lead to deleterious effects induced by the stainless-steel milling media.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

FAST Irradiations, Postirradiation Examinations, and Modeling of U-Mo for Light Water Reactor Applications

Many next generation light water reactor (LWR) concepts, such as mobile small modular reactors, are seeking to use smaller core dimensions than conventional reactor types. Smaller reactor cores require an increase in fissile material to maintain reactivity. For non-proliferation purposes, enrichment increases are limited to less than 20% (high assay low enriched uranium, [HALEU]) and so higher uranium density fuels than UO 2 must be considered. To this end, uranium-molybdenum alloys were tested using the Fission Accelerated Steady-state Test (FAST) approach. The experiment test matrix is focused on identifying the temperature transition between low swelling and high fission gas retention to break away swelling and low fission gas retention. This paper documents the results of irradiation tests and post-irradiation examinations (PIE) including neutron radiography, rodlet profilometry, fission gas collection analysis, and optical metallography. The results of these tests showed that unconstrained U-Mo fuels (solid, Na-bonded rodlets) have a swelling threshold between 400-450°C with minimal fission gas release below this point. Higher temperature solid fuel showed microstructural zoning with small pore networks while lower temperature solid fuels have a uniform microstructure with large pore networks. U-Annular Mo fuels where swelling had some self-constraint imposed upon it, were shown to have much reduced swelling compared to their solid counterparts as well as very low fission gas release for irradiation temperatures up to 500°C. These initial results show that the use of U-Mo in constrained fuel geometries could be used as a high uranium density HALEU fuel for LWRs.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Mapping the Microhardness of Al Matrix in U-7Mo/Al Dispersion Fuels at Medium and High Burn-up by in situ Nanoindentation

The mechanical degradation of the Al matrix in U-7Mo dispersion fuels was detected after irradiation in previous studies, but more details of the degradation mechanism are not clear yet to clarify the root cause. In this study, microhardness mapping in fresh and irradiated U-7Mo dispersion fuels coated with ZrN, with burn-up of 3.35 × 10 21 and 6.28 × 10 21 f/cm 3 , are measured to reveal the hardening of the Al matrix as a function of distance to fuel particles. Micro cubes were pulled by plasma focused ion beam scanning electron microscopy and tested by in situ nanoindenter with Berkovitch tip. Size effects are measured in medium and high burn-up samples. The higher burn-up specimen exhibits a more pronounced size effect when indent load is lower than 20 mN. Size effect correction models are also calculated by plots fitting, which predicts the true microhardness without size effect. Results shows that the hardness of the Al matrix near the ZrN coating has the highest value, then decreases moving away from the coating and become stable when the distance reaches ∼10 µm. The hardness starts increasing again getting closer to the next fuel particle, which makes the hardness distribution between two fuel particles to be “U” shape.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Interfacial Analysis of Blister Formation in U-10Mo Mini-Plates

A thorough investigation of potential failure mechanisms builds confidence in the performance of monolithic U-10wt%Mo (U-10Mo) fuel plates. The lowenriched uranium (LEU) fuel system is currently undergoing qualification as a high U-density fuel that can be used to convert United States high-performance research reactors from high-enriched uranium (HEU) operation. This will require establishing fuel operational limits such that fission products and a coolable geometry are retained, even during off-normal reactor operation conditions [1]. Such off-normal conditions can subject the fuel plates to temperatures where the internal pressure of precipitated fission gasses result in a permanent deformed, raised area of the cladding, referred to as a blister. These blisters can reduce the local coolability of a fuel plate and can even close coolant channels of a fuel assembly, so blistered plates are considered failed regardless of whether the fuel is truly breached. Historically, a marginto- failure is established through out-of-pile blister threshold testing of irradiated fuel plates. This is accomplished by incrementally heating irradiated fuel plates until blisters are observed. This reveals the temperature threshold that would have resulted in a blister if a plate experienced them at those irradiation conditions [2]. While the blister testing itself reveals the temperatures at which the cladding mechanical integrity was exceeded, a more thorough investigation of the interface evolution in proximity to formed blisters may reveal mechanisms as to the blister formation and retention of fission gases. Previous studies have explored potential underlying mechanisms in historical plates that may have been close to blistering [3]; however, this work is the first exploration of blister tested irradiated plates, fabricated by a commercial vendor—another requirement for qualification of the fuel system [1]. The Mini-plate 1 (MP-1) experiment was the first in a series of irradiation and post-irradiation examination (PIE) campaigns to qualify the U-10Mo monolithic fuel system. It consisted of commercially fabricated 25.4×101.5 mm Al-clad mini-plates with a monolithic U-10Mo foil coated in a Zr diffusion barrier. The primary MP-1 PIE campaign was previously completed. Among the suit of examinations was a blister testing campaign, where plates were incrementally annealed in 25°C increments until blisters were observed or a maximum temperature of 550°C was reached [4]. The previously blistered plates from this campaign were revisited in this work.

25228↗
DOE OSTI2025

Micro-tensile testing of neutron-irradiated Al/Zr and Zr/U-Mo diffusion bonds

This study focuses on micro-tensile testing of neutron-irradiated Al/Zr and Zr/U-Mo diffusion bonds, which are integral to the structure and performance of nuclear fuel plates used in the fuel being developed for U.S. high-power research reactors. During fabrication, two distinct diffusion bonds occur—one at the Zr/U-10Mo interface via roll bonding, and the Zr/Al interface via hot isostatic pressing at 833 K. This work utilizes micro-tensile testing specimens approximately 7 × 7 × 18 μm 3 , which are sufficiently large to encompass the identified diffusion zones to evaluate the failure strength and identify the failure location. For the Zr/Al interface, all failures occurred in the bulk aluminum. The average yield strength, ultimate strength, and strain at failure for the two parent samples were: 125 ± 10 MPa, 139 ± 24 MPa, 156 ± 21 MPa, 185 ± 14 MPa, 37.9 ± 5.6 %, and 29.7 ± 3.4 %, respectively. For specimens across the Zr/U-Mo interface, failures occurred either in the bulk Zr or U-Mo, with no failures observed in the diffusion region. For specimens that failed in the bulk Zr the failure strength and strain for the two parent samples were 570 MPa, 710 ± 131 MPa, and 43.3 %, 27.3 ± 6.6 % respectively. The specimens that failed in the bulk U-Mo had failure strengths and strains of 596 ± 32 MPa, 548 ± 124 MPa, and 2.2 ± 1.3 %, 1.5 ± 0.6 % respectively. In conclusion, these findings support the development of accurate thermo-mechanical models for irradiated fuel performance by identifying the mechanical limits and failure locations within the bonded regions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Tensile properties of co-rolled Zr/U-10Mo fuel at ambient and elevated temperatures

The United States High Performance Research Reactor (USHPRR) initiative is currently interested in replacing high-enriched uranium fuel in research reactors with high-assay low-enriched uranium fuel. Here, this work aimed to assist in that mission by providing tensile and bend test data on bare U-Mo and tensile test data on co-rolled Zr/U-10Mo plates at differing thicknesses (0.285 mm, 0.300 mm, and 0.465 mm) and temperatures (293 K, 473 K, and 623 K). Yield strength and ultimate tensile strength values are reported along with an in-depth comparison of how temperature, rolling direction, thickness, and the presence of the Zr-interlayer affect mechanical properties. Results showed that yield strength and ultimate tensile strength in Zr/U-10Mo foils lower as temperature increases by approximately 300 MPa from 293 to 473 K, and another 100 MPa from 473 to 623 K. Additionally it was found that with increased temperature, there is less differentiation in fuel necking and delamination behavior, as well as a greater perceived elongation to fracture. The elastic modulus of co-rolled mini-plates does not follow the volumetric rule of mixtures in terms of averaged strength and is actually lower than the reported moduli of both Zr and U-10Mo.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

A machine learning approach to quantify degradation of nuclear fuels and the effects of fission products

Nuclear fuel performance is critically dependent on understanding the evolution of fuel properties under operational conditions, a complex challenge driven by chemical changes and substantial radiation damage during fission. Traditionally, property evolution has been determined via empirical data collected following irradiation. However, these empirical correlations are limited in their applicability beyond the specific conditions in which they were obtained. This study explores a novel approach to address this challenge by applying materials informatics to develop a machine learning random forest (ML-RF) model that captures the effects of fission products on fuel compounds. The model predicts formation enthalpy (ΔH f ) by leveraging extensive quantum materials property data and correlating it with material descriptors such as composition, atomic and site features, and crystal lattice properties. This ML-RF model enables rapid interpolation across the compositional and structural spaces covered by the training data, thus supporting high-throughput screening and energetic ranking of candidate phases. The model demonstrates the ability to predict ΔH f with a mean absolute error (MAE) of approximately 0.1 to 0.2 eV/atom across a wide range of compounds, including key nuclear fuel systems (U-O, U-N, U-C, U-Si, and U-Mo). For example, it was used to assess shifts in stoichiometry for UO 2 (O/M) and UN (N/M) fuels, revealing their distinct tendencies in chemical potential variation and enabling preliminary convex hull analyses. Furthermore, the model provides insights into how individual fission products affect fuel properties. Results indicate that larger fission products (e.g., Nd, Pu, Ce) have a more pronounced impact on UO 2 , while lighter ones (e.g., Zr) strongly influence UN. Here, the model developed in this work can be used to support the Accelerated Fuel Qualification approach by facilitating preliminary evaluations prior to extensive materials modeling and experimentation. To this end, the trained model has been made available to the fuel community to support ongoing fuel development efforts.

Accelerated fuel qualification↗