Search NASA⌕ Search

SEARCH · Search NASA

Results for “UPWASH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Predicted upwash angles at engine inlets for STOL aircraft

Upwash angles were predicted for a STOL lifting system by using a two-dimensional potential flow analysis. Upwash angles are presented for distances ahead of the wing leading edge of 50, 75, and 100 percent of wing chord. The upwash angle was determined to be insensitive to the vertical location of the engine inlet. For a wide range of takeoff and landing conditions, the upwash angle was found to be a function of the total two-dimensional lift coefficient. Upwash angles, along with typical flow fields, are presented for a range of total two-dimensional lift coefficients from 2 to 12. Three-dimensional effects were considered in estimating upwash angles for an unswept-wing externally blown flap aircraft. For this STOL configuration, effective upwash angles during takeoff, approach, and waveoff conditions were found to be 22 deg, 26 deg, and 36 deg, respectively.

Albers, J. A.↗
NASA NTRS1975

Low-speed upwash interference on a transport model in a rectangular slotted-wall wind tunnel

A study was made of the upwash interference caused by the wind tunnel walls at a Mach number of 0.20. The wind tunnel has slotted horizontal walls and solid vertical walls and the wind tunnel model is a wing-fuselage combination typical of a short take-off and landing (STOL) transport. Measurements were made of the model forces and angle of attack. The experimental results are compared to theoretical solutions for the upwash interference. This comparison enabled an indirect determination of one of the constants in the slotted wall boundary condition. The magnitude of the experimental upwash interference is also compared to the accuracy of the data. This comparison indicates that it is difficult to make definite conclusions based on the experimental data. Suggestions are made for future research which could provide a practical means of accurately determining the wall-interference velocities in wind tunnels with rigid slotted walls.

Mann, M. J.↗
NASA NTRS1985

Fuselage upwash effects on RSRA rotor systems

The effects of RSRA fuselage configurations on rotor performance and loads have been quantified analytically by means of currently available potential flow and rotor analysis. Four configurations of the Rotor Systems Research Aircraft (RSRA) were considered in this study. They were: (1) fuselage alone (conventional helicopter); (2) fuselage with auxiliary propulsion; (3) fuselage with wings (auxiliary lift); and (4) fuselage with both auxiliary lift propulsion. The rotor system investigated was identical to a CH-47D front rotor except that it had four instead of three blades. Two scaled-down versions of the same rotor were also analyzed to determine the effect of rotor scale on the fuselage upwash effects. The flight conditions considered for the upwash study are discussed. The potential flow models for the RSRA configuration, with and without the wings and the auxiliary propulsion system, are presented. The results of fuselage/wing/propulsion system upwash on performance and loads are also presented.

Cowan, J.↗
NASA NTRS1987

High-angle-of-attack pneumatic lag and upwash corrections for a hemispherical flow direction sensor

As part of the NASA F-14 high angle of attack flight test program, a nose mounted hemispherical flow direction sensor was calibrated against a fuselage mounted movable vane flow angle sensor. Significant discrepancies were found to exist in the angle of attack measurements. A two fold approach taken to resolve these discrepancies during subsonic flight is described. First, the sensing integrity of the isolated hemispherical sensor is established by wind tunnel data extending to an angle of attack of 60 deg. Second, two probable causes for the discrepancies, pneumatic lag and upwash, are examined. Methods of identifying and compensating for lag and upwash are presented. The wind tunnel data verify that the isolated hemispherical sensor is sufficiently accurate for static conditions with angles of attack up to 60 deg and angles of sideslip up to 30 deg. Analysis of flight data for two high angle of attack maneuvers establishes that pneumatic lag and upwash are highly correlated with the discrepancies between the hemispherical and vane type sensor measurements.

Whitmore, Stephen A.↗
NASA NTRS1975

Upwash angles near engine inlets of an externally blown flap STOL transport

An investigation was conducted in the Langley V/STOL tunnel to determine the upwash flow angles in the region of the nacelle inlets of a representative powered-lift transport configuration operating at high lift coefficients. The upwash angles were indicated by tufts and measured from photographs. A potential-flow program was used to estimate these flow angles. Large upflow angles exist near the inlets of the nacelles; the highest value (67.3 deg) occurred with flaps at 15, 35, 55 deg, an angle of attack of 25.7 deg, and a thrust coefficient of 4. The upflow angle was found to be strongly dependent on the circulation lift, regardless of the flap deflection, angle of attack, or thrust coefficient used to generate this circulation lift. The potential-flow calculations away from the nacelle inlets agreed fairly well with the experimental data.

Naeseth, R. L.↗
NASA NTRS1984

Effect of fuselage upwash on the supersonic longitudinal aerodynamic characteristics of 2 fighter configurations

An experimental and theoretical investigation of fuselage incidence effects on two fighter aircraft models, which differed in wing planform only, has been conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.6, 1.8, and 2.0. Results were obtained on the two models at fuselage incidence angles of 0 deg, 2 deg, and 5 deg. The fuselage geometry included two side-mounted, flow-through, half-axisymmetric inlets and twin vertical tails. The two planforms tested were cranked wings with 70 deg/66 deg and 70 deg/30 deg leading-edge sweep angles. Experimental data showed that fuselage incidence resulted in positive increments in configuration lift and pitching moment; most of the lift increment can be attributed to the fuselage-induced upwash acting on the wing and most of the pitching-moment increment is due to the fuselage. Theoretical analysis indicates that linear-theory methods can adequately predict the overall configuration forces and moments resulting from fuselage upwash, but a higher order surface-panel method (PAN AIR) more accurately predicted the distribution of forces and resulting moments between the components.

Wood, R. M.↗
NASA NTRS1987

Unsteady three-dimensional simulation of VTOL upwash fountain turbulence

Numerical simulations of a planar turbulent wall jet and a planar VTOL upwash fountain were performed. These are three dimensional simulations which resolve large scale unsteady motions in the flows. The wall jet simulation shows good agreement with experimental data and is presented to verify the simulation methodology. Simulation of the upwash fountain predicts elevated shear stress and a half velocity width spreading rate of 33% which agrees well with experiment. Turbulence mechanisms which contribute to the enhanced spreading rate are examined.

Childs, Robert E.↗
NASA NTRS1990

Numerical study of twin-jet impingement upwash flow

Two horizontally spaced jets impinging normally on a flat surface create a fountain upwash flow due to the collision of the radially flowing wall jets. This fountain flow is of importance to the dynamics and propulsion of STOVL aircraft. The fountain flow influences the lift forces on the aircraft and the ingestion of hot gases and debris by the engine inlet. In this paper, a multigrid based finite-difference numerical procedure has been applied to solve the equations governing this three-dimensional flow. The standard k-epsilon turbulence model has been used. Comparisons with experimental data reveal that while the mean velocities are predicted with reasonable accuracy, the turbulent kinetic energies are seriously in error. The reasons for this discrepancy could be the intense unsteadiness and large-scale structures of the flow in the near-wall region, which cannot be captured well by any Reynolds-averaged turbulence model.

Pegues, W. J.↗