Search NASA⌕ Search

SEARCH · Search NASA

Results for “Uranium nitride”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

NSUF RTE completion report for 23-4780: Microstructural Defect Induced Thermal Conductivity Reduction in Uranium Nitride and Thorium Nitride

Uranium nitride (UN) is known to have a higher thermal conductivity than traditional oxide fuels, which could lead to a more efficient energy transport and lower local temperature during its lifetime. But the thermal transport performance of UN in extreme environments has not been systematic studied. This study investigated the irradiation induced microstructural defects in UN and the impacts on thermal conductivity. The samples were produced by spark plasma sintering at University of Texas-San Antonio (UTSA), Los Alamos National Laboratory (LANL), and Idaho National Laboratory (INL). Thermal conductivity of UN before and after 2MeV proton irradiation were measured by using laser metrology at INL in a temperature range of 77-295K. Thermal conductivity measurements in this wide, cryogenic temperature range is critical to understand the phonon scattering mechanisms between the thermal energy carrier, phonons, and different types of irradiation-induced defects. In order to ensure the measurements were conducted in the same grains and minimize the impact of the local heterogeneities, the measurement locations were highlighted by fiducial marks using the focused ion beam (FIB) with grain orientation identified using the electron backscatter diffraction (EBSD) at the Center of Advanced Energy Studies (CAES). Irradiation experiment was conducted at the Ion Beam Laboratory at Texas A&M University (TAMU). A total of 6 samples were irradiated with different irradiation doses and temperatures. After irradiation, the microstructure was characterized by using Transmission Electron Microscope (TEM) at CAES (also in the FIB marks).

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Mechanistic nuclear fuel performance modeling of uranium nitride

Uranium mononitride (UN) is a nuclear fuel candidate for advanced reactor designs and an alternative being considered for light water reactors due to its higher thermal conductivity and uranium density than UO 2 . As with any nuclear fuel, swelling and fission gas release are important factors for safety, while also being some of the hardest phenomena to predict with a high degree of confidence. Getting a grasp on the gas swelling behavior and release is crucial to lower the barrier for UN utilization. An accelerated swelling rate at high temperatures observed experimentally, sometimes referred to as “breakaway swelling,” further complicates the prediction of fuel performance of UN. A mechanistic model has been developed using a multiscale approach to describe the intragranular and intergranular fission gas behavior. Lower-length-scale calculations have been employed to inform models of the gas and self-diffusion behavior, resolution rate, and bubble shape. Leveraging previous work on high burnup UO 2 , two populations of intragranular bubbles are considered; small bulk bubbles and larger bubbles located along dislocations. The dislocation bubbles were found to be crucial to the overall swelling behavior, and the breakaway swelling transition was associated with the transition in the gas atom diffusion mechanism from an irradiation-induced athermal diffusion regime at lower temperatures to an intrinsic thermal equilibrium regime at higher temperatures, accelerating the growth of the dislocation bubbles. Similarly, the threshold for fission gas release was associated with the grain boundary vacancy diffusivity surpassing the gas atom diffusivity at sufficiently high temperatures, allowing the over-pressurized grain boundary bubble to grow in size and interconnect. Using thermo-mechanical models with the fission gas model, two integral fuel pin assessment cases were simulated. Finally, this work demonstrates the ability of a multiscale approach to accelerate the understanding of advanced fuel forms when experimental data is limited.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1975

Evaluation of refractory-metal-clad uranium nitride and uranium dioxide fuel pins after irradiation for times up to 10 450 hours at 990 C

The effects of some materials variables on the irradiation performance of fuel pins for a lithium-cooled space power reactor design concept were examined. The variables studied were UN fuel density, fuel composition, and cladding alloy. All pins were irradiated at about 990 C in a thermal neutron environment to the design fuel burnup. An 85-percent dense UN fuel gave the best overall results in meeting the operational goals. The T-111 cladding on all specimens was embrittled, possibly by hydrogen in the case of the UN fuel and by uranium and oxygen in the case of the UO2 fuel. Tests with Cb-1Zr cladding indicate potential use of this cladding material. The UO2 fueled specimens met the operational goals of less than 1 percent cladding strain, but other factors make UO2 less attractive than low-density UN for the contemplated space power reactor use.

Bowles, K. J.↗
DOE OSTI2024

Raman spectroscopy of uranium nitride kernels

Uranium nitride is an advanced fuel candidate for a wide variety of advanced nuclear reactors. This work summarizes the first characterization of UN kernels by Raman spectroscopy. First-principles density functional theory calculations were performed to predict the Raman spectra of uranium sesquinitride (U 2 N 3 ), uranium dinitride (UN 2 ), uranium mononitride (UN), uranium monocarbide (UC), as well as U-N-C (UN 1-x C x ) and a U-N-C-O mixture. Further, a core–shell structure was identified by scanning electron microscopy and Raman spectroscopy imaging. A signal at ~500 cm -1 was identified on the periphery of the core-shell structure, possibly corresponding to U 2 N 3 and/or UN 2 . This signal broadens and shifts to 470 cm -1 because of the formation of UNC, UNCO or U 2 N 3+x structures. The culmination of this work demonstrates the feasibility of using Raman spectroscopy to identify variations in composition and phases in UN kernels.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Assessment of uranium nitride interatomic potentials

Uranium mononitride (UN) is a promising nuclear fuel due to its high fissile density, high thermal conductivity, and suitability for reprocessing. In this study, two uranium nitride interatomic potentials are assessed: Tseplyaev and Starikov's angular-dependent potential and Kocevski et al.'s embedded atom model potential. Predictions of the thermophysical and elastic properties of UN, UN 2 , and α- and β-U 2 N 3 computed using both potentials are assessed and compared to available experimental data. Notably, the Tseplyaev potential performs better with the energetic aspects of UN, e.g., specific heat capacity and point defect formation energies, whereas the Kocevski potential performs better with the structural aspects of UN, e.g., thermal expansion as well as with the elastic properties. The reasons why the Kocevski potential underestimates the UN specific heat are explained by examining the UN phonon properties modeled using both potentials. The Kocevski potential shows better identification of the mechanical stability ranges of UN, UN 2 , and α- and β-U 2 N 3 , reasonably predicting the melting point of UN and predicting stable structures for UN 2 and α- and β-U 2 N 3 . On the other hand, the Tseplyaev potential predicts a premature phase change of both UN and UN 2 and cannot stabilize α- nor β-U 2 N 3 . However, the Kocevski potential cannot predict a stable α-U phase and is thus not suitable for the calculation of formation energies for non-stoichiometric point defects.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1973

Uranium nitride behavior at thermionic temperatures

The feasibility of using uranium nitride for in-core thermionic applications was evaluated in electrically heated thermal gradient tests and in flat plate thermionic converters. These tests indicated that grain boundary penetration of uranium nitride into both tungsten and rhenium will occur under thermal gradient conditions. In the case of the tungsten thermionic converter, this led to grain boundary rupture of the emitter and almost total loss of electrical output from the converter. It appears that uranium nitride is unsuitable for thermionic applications at the 2000 K temperatures used in these tests.

Phillips, W. M.↗
DOE OSTI2026

ROADRUNNER uranium nitride MiniFuel: Experimental design, fabrication and pre-irradiation baseline characterization for accelerated burnup testing

Uranium nitride (UN) is a promising fuel candidate for advanced reactor systems owing to its high uranium density and thermal conductivity; however, its qualification remains constrained by the scarcity of well-controlled irradiation performance data. Here, to address this limitation, the ROADRUNNER (Research On ADvancing the peRformance of UraNium Nitrides in Extreme enviRonments) campaign employs the MiniFuel platform in the High Flux Isotope Reactor (HFIR) to enable accelerated burnup irradiation testing under tightly controlled and largely isothermal conditions. This paper presents the experimental design, fuel fabrication, and pre-irradiation baseline characterization of the ROADRUNNER UN MiniFuel campaign. Thirty-six UN minidisc specimens were fabricated with systematically varied as-fabricated density (86–96% of theoretical density), carbon impurity content (961–5240 ppm), oxygen content (≤ ∼2000 ppm), and grain size (2.5–24 μm). The irradiation matrix spans nominal fuel temperatures of 873 K, 1173 K, and 1473 K and target burnups of 3.75%, 6.0%, and 7.5% fissions per initial metal atom (FIMA). Neutronic and thermal analyses were performed to define specimen-specific burnup accumulation and temperature histories, establishing the boundary conditions for subsequent in-pile behavior. Comprehensive pre-irradiation characterization—including dimensional metrology, density verification, impurity analysis, X-ray diffraction, Raman spectroscopy, scanning electron microscopy, X-ray computed tomography, and confocal profilometry—provides a detailed baseline for post-irradiation examination. Pre-irradiation data were further used to generate predictive estimates of fission gas release and swelling using existing empirical correlations. This quantitative comparison reveals substantial inter-model divergence at intermediate and elevated temperatures that exceeds propagated input uncertainties, highlighting structural gaps in the historical irradiation database. The ROADRUNNER irradiation campaign is currently underway in HFIR, with initial firs cycle completed in late 2025 and remaining targets scheduled through 2027. The experimental design and baseline dataset presented here establish the framework needed to interpret forthcoming post-irradiation measurements and to provide discriminating data for the validation and refinement of physics-based UN fuel performance models.

Lopes, Denise Adorno [Oak Ridge National Laborator↗
NASA NTRS1971

Evaluations of uranium-nitride fueled converters.

Evaluation of two uranium-nitride (UN) fueled converters was initiated at the Jet Propulsion Laboratory to investigate the effect of fuel on the converter performance while being operated out-of-core. The initial tests were performed with the dynamic data acquisition system that was developed at the Laboratory. Parametric tests of these converters were to obtain: (1) static volt-ampere curves, (2) dynamic volt-ampere curves, and (3) the electrode work functions. The power outputs were 9.3 W/sq cm for the rhenium converter and 3.8 W/sq cm for the tungsten converter at 0.6 V when the emitter surface temperature was 2000 K, according to the static volt-ampere curves.

Shimada, K.↗
DOE OSTI2026

Physicochemical evolution of uranium nitride kernel microstructure with varying carbon distribution for advanced TRISO fuel forms

Uranium nitride (UN) has emerged as a fuel candidate for advanced nuclear reactor concepts due to its superior uranium density, thermal conductivity, and high melting temperature. However, the fabrication route for converting UO 2 to UN is complex and difficult to standardize. Although the chemistry of this conversion process is well-studied, more insight into the physicochemical dynamics of this conversion using advanced characterization techniques can help further our understanding of this material system. This work leveraged thermogravimetric analysis (TGA), X-ray diffraction (XRD), and nondestructive 3D X-ray computed tomography (XCT) to characterize dynamic microstructural changes in the UO 2 → UCO → UN fabrication pathway for two kernels with a varying carbon distribution in the starting composition. TGA and XRD were used to quantify changes in the mass, density, and chemical composition of the two kernels, while three-dimensional image processing and segmentation of XCT data were used to quantify the volume, surface area, and spatial distribution of features within each kernel for multiple steps along the fabrication pathway. The analysis indicates distinct differences between the two kernels that are correlated to downstream conversion efficiency. In conclusion, this work is among the first to perform 3D quantification of physicochemical evolution during UN conversion, providing quantitative correlation between processing, properties, and expected fuel performance.

Nuclear fuel↗
DOE OSTI2025

Machine learning interatomic potential for predicting the thermal properties of uranium nitride

We present a combined computational and experimental investigation of the thermal properties of uranium nitride (UN), focusing on the development of a machine learning interatomic potential (MLIP) using the moment tensor potential framework. The MLIP was trained on density functional theory (DFT) data and validated against various quantities including energies, forces, elastic constants, phonon dispersion, and defect formation energies, achieving excellent agreement with DFT calculations, prior experimental results, and our thermal conductivity measurement. The potential was then employed in molecular dynamics simulations to predict key thermal properties such as melting point, thermal expansion, specific heat, and lattice thermal conductivity. To further assess model accuracy, we fabricated a UN sample and performed new thermal conductivity measurements representative of single-crystal properties, which showed strong agreement with the MLIP predictions. This work confirms the reliability and predictive capability of the developed potential for determining the thermal properties of UN.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Thermophysical Properties of a Uranium Nitride–Molybdenum-Tungsten Composite Fuel for Nuclear Thermal Propulsion

The thermal conductivity of a ceramic-metal composite consisting of 60 vol % uranium nitride incorporated into a molybdenum-tungsten matrix has been measured up to a temperature of 1200°C. Compositing nuclear fuel with refractory materials is considered a viable way to improve the thermal and mechanical properties of fuels, and more recently, has been investigated as a way to improve hydrogen compatibility in a nuclear thermal propulsion rocket reactor. Here, we demonstrate that high-density composites can be produced from direct current sintering and that the resulting thermal conductivity is improved compared to the pure.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Survey of Uranium Nitride and Mixed Oxide Fuels for Microreactor Applications

Different fuel systems are being proposed for use in microreactors including TRISO fuel and metallic U-Zr based fuel. TRISO fuel is considered the main fuel option for most of the industry teams. Given the need for compact size core and potential for long fuel life of a microreactor, high density fuels such as metallic and nitride fuels are potential options. Of interest here is the uranium nitride (UN) option, which can allow for higher fissile material content and higher thermal conductivity compared to conventional uranium oxide fuel, and also has higher melting temperature compared to metallic fuel. Meanwhile, the current availability is limited for high assay low enriched uranium (HALEU) that is needed for high density fuels, which motivates the consideration of using Pu as a potential replacement for HALEU until adequate production capacity is in place. Current Pu availability is mainly attributed to the inventory of excess weapons Pu rather than through reprocessing of spent nuclear fuel. This inventory of excess Pu can be used in both metallic and oxide fuel systems to replace HALEU. Of interest here, the oxide form, that is the mixed oxide form of PuO 2 and UO 2 (MOX). In this report, the options of using UN or MOX, in both pellet and TRISO fuel forms, in microreactors are evaluated in relation to their properties, fuel performance and irradiation data, as well as fabrication. Gaps related to those areas are identified for both fuel systems, to guide future activities by DOE programs such as the advanced fuels campaign (AFC), to enable their use in microreactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Formation of uranium nitride nanoparticles via mechanical alloying of uranium-molybdenum alloy fuels in gaseous nitrogen

Uranium-molybdenum (U-Mo) alloys show promise as a nuclear fuel system due to their high thermal conductivity and fuel loading capability. However, U-Mo systems are susceptible to irradiation induced swelling ultimately affecting the cladding via mechanical and chemical interactions. To address these shortcomings, this research investigated the formation of uranium mononitride (UN) nanoparticles within a 90 wt% U/10 wt% Mo (U-10Mo) matrix to act as a prospective defect sink for fission products at nanometric hetero-interfaces. To promote the formation of UN, U-10Mo powders were mechanically alloyed under a high purity nitrogen atmosphere. Variations of the milling process investigated included media size, duration of milling, and number of times the milling jar was re-aerated with nitrogen gas. Characterization of the fuel microstructure was completed using light element analysis, X-ray diffraction, scanning and transmission-electron microscopy, electron energy loss spectroscopy, and atom probe tomography. UN nanoparticles measuring 1–5 nm in radius were observed in the U-Mo matrix as early as 1 h into the mechanical alloying process. Milling time in excess of 10 h was found to lead to deleterious effects induced by the stainless-steel milling media.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Machine learning models for volumetric swelling in uranium nitride

Machine learning methods are applied to predict the volumetric swelling rate of the nuclear fuel uranium nitride (UN) over various temperatures, irradiation conditions, and power densities. Both kernel-based methods and symbolic regression models for UN swelling are developed and compared with multiple experimental datasets. We find that the UN pellet geometry and dimensions must be taken into account to accurately model swelling behavior. Strong agreement is observed between the developed machine learning models and the data. The predictive error generated by the machine learning models improves on empirical models taken from the literature. Sensitivity analysis is performed to determine which properties such as temperature, burnup, and power density, are most important in the swelling process. We find that machine learning can be used to quickly develop accurate swelling models for nuclear materials. In conclusion, the presented results illustrate the potential of machine learning to determine volumetric swelling in UN.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Measuring thermal diffusivity and gap conductance in uranium nitride and Zircaloy relevant for microreactor applications

Heat transfer across nuclear fuels and structural interfaces is an important factor for evaluating the performance of nuclear power systems. Specifically, heat generated as nuclear fuel fissions must be transported through the cladding material and through the reactor to reach the steam turbine for power generation. As new microreactor designs emerge, maximizing the efficiency of this heat transfer process becomes crucial to make them commercially viable. This article examines thermal diffusivity and gap conductance in uranium nitride (UN) fuel and Zircaloy-4 (Zry4) cladding using light flash analysis (LFA). Thermal diffusivity measurements were made on monolithic UN pellets and Zry4 exposed to carbon at peak operating temperatures of microreactors and show that carbon ingress has a minimal effect on thermal diffusivity when compared with identical materials not exposed to carbon. Evaluation of gap conductance at the UN-Zry4 interface was done using one-dimensional two-layer thermal transport models as a function of applied pressure. Here the results show that increasing pressure on the UN-Zry4 interface leads to gains in gap conductance per unit area in fuel-cladding assemblies at microreactor operating temperatures. While many other variables are expected to influence UN-Zry4 interfacial gap conductance (e.g. contact surface roughness, porosity, localized heating, environmental gas pressure), the work offers a demonstration of using a conventional LFA apparatus to determine this parameter at elevated temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1973

Examination of T-111 clad uranium nitride fuel pins irradiated up to 13,000 hours at a clad temperature of 990 C

The examination of 27 fuel pins irradiated for up to 13,000 hours at 990 C is described. The fuel pin clad was a tantalum alloy with uranium nitride as the nuclear fuel. Two nominal fuel pin diameters were tested with a maximum burnup of 2.34 atom percent. Twenty-two fuel pins were tested for fission gas leaks; thirteen pins leaked. Clad ductility tests indicated clad embrittlement. The embrittlement is attributed to hydrogen from an n,p reaction in the fuel. Fuel swelling was burnup dependent, and the amount of fission gas release was low, generally less than 0.5 percent. No incompatibilities between fuel, liner, and clad were in evidence.

Slaby, J. G.↗