SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Report discusses the theory of energy losses in wind tunnels, the application of the Drzewiecki theory of propeller design to wind tunnel propellers, and the efficiency and steadiness of flow in model tunnels of various types.
This report is a continuation of National Advisory Committee for Aeronautics report no. 73. The variations in velocity and direction of the wind stream were studied by means of a recording air speed meter and a recording yawmeter. The work was carried on both in a 1-foot diameter model tunnel and in a 5-foot full-size tunnel, and wherever possible comparison was made between them. It was found that placing radial vanes directly before the propeller in the exit cone increased the efficiency of the tunnel to a considerable extent and also gave a steadier flow.
Wind tunnel modifications consisting of the introduction of new turning vanes, baffles, diffuser, and test section were completed in 2019. Wind tunnel characterization best practices require a full characterization test entry following any of these modifications.
Wind tunnel for large component testing uses a jet engine with afterburner to provide high temperatures /1200 degrees to 2000 degrees F/ and controlled high velocity gas. This economical wind tunnel can accommodate parts ten feet by ten feet or larger, and is a useful technique for qualitative information.
Recent experimental and numerical evidence has shown that the cumulative wake generated from the overlapping of multiple wakes within a wind farm could reduce power performance and enhance fatigue loads of wind turbines installed in neighboring downstream wind farms and may also extend up to distances one order of magnitude larger than those typically considered for intra-farm wake interactions. Similar to individual wind turbine wakes, wind farm wakes have a velocity deficit and added turbulence intensity, both affected by the turbine rotor thrust forces and the incoming turbulence intensity. Therefore, the evolution of wind farm wakes will vary for different operational and atmospheric conditions. In this paper, lidar measurements collected during the American WAKE experimeNt (AWAKEN) and wind tunnel tests of wind farms reproduced by porous disks are leveraged to investigate wind farm wakes.
Wind tunnel testing of helicopters, and test program for Polish helicopter industry
Wind tunnel construction and design is discussed especially in relation to subsonic and supersonic speeds. Reynolds Numbers and the theory of compressible flows are also taken into consideration in designing new tunnels.
Wind tunnel measurements of the rotor trim, blade airloads, and structural loads of a full-scale UH-60A Black Hawk main rotor are compared with calculations obtained using the comprehensive rotorcraft analysis CAMRAD II and a coupled CAMRAD II/OVERFLOW 2 analysis. A speed sweep at constant lift up to an advance ratio of 0.4 and a thrust sweep at constant speed into deep stall are investigated. The coupled analysis shows significant improvement over comprehensive analysis. Normal force phase is better captured and pitching moment magnitudes are better predicted including the magnitude and phase of the two stall events in the fourth quadrant at the deeply stalled condition. Structural loads are, in general, improved with the coupled analysis, but the magnitude of chord bending moment is still significantly underpredicted. As there are three modes around 4 and 5/rev frequencies, the structural responses to the 5/rev airloads due to dynamic stall are magnified and thus care must be taken in the analysis of the deeply stalled condition.
Wind Tunnel test at a tunnel Mach number of 0.10. This was an entry to investigate the effect of “stator clocking” on noise. The fan consisted of a moderately aft swept rotor and an aft swept set of stator vanes. The fan stage consisted of 22 rotor blades, 50 stator vanes, and 10 downstream support struts. A set of stator vanes designed for lower noise was tested as well as a baseline stator vane set. The stator assembly could be rotated several degrees to adjust the clocking angle between the stator vane pack and the strut assembly. All configurations were with a hard wall duct (no acoustic treatment). The NASA Glenn Research Center’s Rotating Rake Mode Measurement System was utilized to obtain a complete map of the acoustic duct modes present in the ducted fan. The system is a radial rake emersed into the duct that continuously rotates about the duct centerline. For the two stator configurations, data were acquired at several different fan speeds which included nominal, approach, cutback, and takeoff conditions. Analysis of the mode power level results at the fan fundamentals showed the improved designed set resulted in lower rotor-stator and rotor-strut interaction acoustic levels for the interaction modes. Varying the angle between the stators and struts was shown to be a viable method to achieve a minimum in rotor-strut interaction mode power level. Multiple-pure-tones generated by the Quiet High Speed Fan II in the inlet were also measured.
Wind Tunnel at a tunnel Mach number of 0.10. This was an entry to investigate the effect of “stator clocking” on noise. The fan consisted of a moderately aft swept rotor and an aft swept set of stator vanes. The fan stage consisted of 22 rotor blades, 50 stator vanes, and 10 downstream support struts. A set of stator vanes designed for lower noise was tested as well as a baseline stator vane set. The stator assembly could be rotated several degrees to adjust the clocking angle between the stator vane pack and the strut assembly. All configurations were with a hard wall duct (no acoustic treatment). The NASA Glenn Research Center’s Rotating Rake Mode Measurement System was utilized to obtain a complete map of the acoustic duct modes present in the ducted fan. The system is a radial rake emersed into the duct that continuously rotates about the duct centerline. For the two stator configurations, data were acquired at several different fan speeds which included nominal, approach, cutback, and takeoff conditions. Analysis of the mode power level results at the fan fundamentals showed the improved designed set resulted in lower rotor-stator and rotor-strut interaction acoustic levels for the interaction modes. Varying the angle between the stators and struts was shown to be a viable method to achieve a minimum in rotor-strut interaction mode power level. Multiple-pure-tones generated by the Quiet High Speed Fan II in the inlet were also measured.
Wind tunnel tests were conducted to determine the aerodynamic heating created by gaps in the reusable surface insulation (RSI) thermal protection system (TPS) for the space shuttle. The effects of various parameters of the RSI on convective heating characteristics are described. The wind tunnel tests provided a data base for accurate assessment of gap heating. Analysis and correlation of the data provide methods for predicting heating in the RSI gaps on the space shuttle.
This paper presents data taken in the 80- by 120-Foot Wind Tunnel in 1992 to data taken in the 40- by 80-Foot Wind Tunnel in 2016 at the NFAC. In both sets of data, the RTA was equipped with an identical set of S-76 helicopter blades. These data sets were compared to determine the repeatability of the RTA as a testing device, and to quantify differences in 40- by 80-Foot Wind Tunnel vs. 80- by 120-Foot Wind Tunnel results. The contents include an overview of the RTA and test facility, as well as a discussion of the methodology used. Vibratory load data is presented for a variety of wind and RPM conditions in various test section configurations. Data presented in this report quantifies the repeatability of the RTA.
Heat transfer data measured in gaps typical of those under consideration for joints in space shuttle reusable surface insulation protection systems have been assimilated, analyzed and correlated. The data were obtained in four NASA facilities. Several types of gaps were investigated with emphasis on simple butt joints. Gap widths ranged from 0.07 to 0.7 cm and depths ranged from 1 to 6 cm. Laminar, transitional and turbulent boundary layer flows over the gap opening were investigated. Three-dimensional heating variations were observed within gaps in the absence of external flow pressure gradients. Heat transfer correlation equations were obtained for several of the tests. Thermal protection system performance with and without gaps was compared for a representative shuttle entry trajectory.
Heat transfer data measured in gaps representative of those being employed for joints in the space shuttle reusable surface insulation (RSI) thermal protection systems (TPS) were assimilated, analyzed, and correlated. Several types of gap were investigated with emphasis on simple butt joints. Gap widths ranged from 0.0 to 0.76 cm and depths ranged from 1 to 6 cm. Laminar, transitional, and turbulent boundary layer flows over the gap opening were investigated. The angle between gap axis and external flow was varied between 0 and pi/2 radians. The contoured cross section gap performed significantly better than all other wide gaps and slightly better than all other narrow gap geometries. Three dimensional heating variations were observed within gaps in the absence of external flow pressure gradients. Interactions between heating within gaps and heating of adjacent top tile surfaces were observed. Gaps aligned with the flow were observed to promote boundary layer transition. Heat transfer correlation equations were obtained for many of the tests. The TPS thickness requirements with and without gaps were computed for a current shuttle entry trajectory. Experimental data employed in the study are summarized. A description of each test facility, run schedule and test conditions, model descriptive information, and heat flux data are included.
For abstract, see N75-28103.
For abstract, see N75-28103.
Wind tunnel interference estimation for model design applications using chart method