Search NASA⌕ Search

SEARCH · Search NASA

Results for “Walker Ridge”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Pore size distribution and methane equilibrium conditions at Walker Ridge Block 313, northern Gulf of Mexico

Coexistence of three methane phases (liquid (L), gas (G), hydrate (H)) in marine gas hydrate systems may occur according to in-situ pressure, temperature, salinity and pore size. In sediments with salinity close to seawater, a discrete zone of three-phase (3P) equilibrium may occur near the base of the regional hydrate stability zone (RHSZ) due to capillary effects. The existence of a 3P zone influences the location of the bottom-simulating reflection (BSR) and has implications for methane fluxes at the base of the RHSZ. We studied hydrate stability conditions in two wells, WR313-G and WR313-H, at Walker Ridge Block 313 in the northern Gulf of Mexico. We determined pore size distributions (PSD) by constructing a synthetic nuclear magnetic resonance (NMR) relaxation time distribution. Correlations were obtained by non-linear regression on NMR, gamma ray, and bulk density logs from well KC-151 at Keathley Canyon. The correlations enabled construction of relaxation time distributions for WR313-G and WR313-H, which were used to predict PSD through comparison with mercury injection capillary pressure measurements. With the computed PSD, L+H and L+G methane solubility was determined from in-situ pressure and temperature. The intersection of the L+G and L+H curves for various pore sizes allowed calculation of the depth range of the 3P equilibrium zone. As in previous studies at Blake Ridge and Hydrate Ridge, the top of the 3P zone moves upwards with increasing water depth and overlies the bulk 3P equilibrium depth. In clays at Walker Ridge, the predicted thickness of the 3P zone is approximately 35 m, but in coarse sands it is only a few meters due to the difference in absolute pore sizes and the width of the PSD. The thick 3P zone in the clays may explain in part why the BSR is only observed in the sand layers at Walker Ridge, although other factors may influence the presence or absence of a BSR.

Bihani, Abhishek↗

Planning and Execution of a Marine Methane Hydrate Pressure Coring Program for the Walker Ridge and Green Canyon Areas of the Gulf of Mexico

The objective of this project (and report) is to produce a guide to developing scientific, operational, and logistical plans for a future methane hydrate-focused offshore pressure coring program. This report focuses primarily on a potential coring program in the Walker Ridge 313 and Green Canyon 955 blocks where previous investigations were undertaken as part of the 2009 Department of Energy JIP Leg II expedition, however, the approach to designing a pressure coring program that was utilized for this project may also serve as a useful model for planning pressure coring programs for hydrates in other areas. The initial portion of the report provides a brief overview of prior investigations related to gas hydrates in general and at the Walker Ridge 313 and Green Canyon 955 blocks in particular. The main content of the report provides guidance for various criteria that will come into play when designing a pressure coring program.

54 ENVIRONMENTAL SCIENCES↗

Numerical simulations of depressurization-induced gas production from gas hydrate reservoirs at the Walker Ridge 312 site, northern Gulf of Mexico

In 2009, the Gulf of Mexico (GOM) Gas Hydrates Joint-Industry-Project (JIP) Leg II drilling program confirmed that gas hydrate occurs at high saturations within reservoir-quality sands in the GOM. A comprehensive logging-while-drilling dataset was collected from seven wells at three sites, including two wells at the Walker Ridge 313 site. By constraining the saturations and thicknesses of hydrate-bearing sands using logging-while-drilling data, two-dimensional (2D), cylindrical, r-z and three-dimensional (3D) reservoir models were simulated. The gas hydrate occurrences inferred from seismic analysis are used to delineate the areal extent of the 3D reservoir models. Numerical simulations of gas production from the Walker Ridge reservoirs were conducted using the depressurization method at a constant bottomhole pressure. Results of these simulations indicate that these hydrate deposits are readily produced, owing to high intrinsic reservoir-quality and their proximity to the base of hydrate stability. The elevated in situ reservoir temperatures contribute to high (5–40 MMscf/day) predicted production rates. The production rates obtained from the 2D and 3D models are in close agreement. To evaluate the effect of spatial dimensions, the 2D reservoir domains were simulated at two outer radii. The results showed increased potential for formation of secondary hydrate and appearance of lag time for production rates as reservoir size increases. Similar phenomena were observed in the 3D reservoir models. The results also suggest that interbedded gas hydrate accumulations might be preferable targets for gas production in comparison with massive deposits. Hydrate in such accumulations can be readily dissociated due to heat supply from surrounding hydrate-free zones. Special cases were considered to evaluate the effect of overburden and underburden permeability on production. The obtained data show that production can be significantly degraded in comparison with a case using impermeable boundaries. The main reason for the reduced productivity is water influx from the surrounding strata; a secondary cause is gas escape into the overburden. The results dictate that in order to reliably estimate production potential, permeability of the surroundings has to be included in a model.

2D and 3D reservoir simulations↗

Studying methane migration mechanisms at Walker Ridge, Gulf of Mexico, via 3D methane hydrate reservoir modeling

We have developed a 3D methane hydrate reservoir simulator to model marine methane hydrate systems. Our simulator couples highly nonlinear heat and mass transport equations and includes heterogeneous sedimentation, in-situ microbial methanogenesis, the influence of pore size contrast on solubility gradients, and the impact of salt exclusion from the hydrate phase on dissolved methane equilibrium in pore water. Using environmental parameters from Walker Ridge in the Gulf of Mexico, we first simulate hydrate formation in and around a thin, dipping, planar sand stratum surrounded by clay lithology as it is buried to 295mbsf. We find that with sufficient methane being supplied by organic methanogenesis in the clays, a 200x pore size contrast between clays and sands allows for a strong enough concentration gradient to significantly drop the concentration of methane hydrate in clays immediately surrounding a thin sand layer, a phenomenon that is observed in well log data. Building upon previous work, our simulations account for the increase in sand-clay solubility contrast with depth from about 1.6% near the top of the sediment column to 8.6% at depth, which leads to a progressive strengthening of the diffusive flux of methane with time. By including an exponentially decaying organic methanogenesis input to the clay lithology with depth, we see a decrease in the aqueous methane supplied to the clays surrounding the sand layer with time, which works to further enhance the contrast in hydrate saturation between the sand and surrounding clays. Significant diffusive methane transport is observed in a clay interval of about 11m above the sand layer and about 4m below it, which matches well log observations. The clay-sand pore size contrast alone is not enough to completely eliminate hydrate (as observed in logs), because the diffusive flux of aqueous methane due to a contrast in pore size occurs slower than the rate at which methane is supplied via organic methanogenesis. Therefore, it is likely that additional mechanisms are at play, notably bound water activity reduction in clays. Three-dimensionality allows for inclusion of lithologic heterogeneities, which focus fluid flow and subsequently allow for heterogeneity in the methane migration mechanisms that dominate in marine sediments at a local scale. Incorporating recently acquired 3D seismic data from Walker Ridge to inform the lithologic structure of our modeled reservoir, we show that even with deep adjective sourcing of methane along highly permeable pathways, local hydrate accumulations can be sourced either by diffusive or advective methane flux; advectively-sourced hydrates accumulate evenly in highly permeable strata, while diffusively-sourced hydrates are characterized by thin strata-bound intervals with high clay-sand pore size contrasts.

Nole, Michael↗

Structural and Stratigraphic Controls on Methane Hydrate occurrence and distribution: Gulf of Mexico, Walker Ridge 313 and Green Canyon 955: Final Report

The goal of this project was to determine structural and stratigraphic controls on hydrate occurrence and distribution in Green Canyon (GC) 955 and Walker Ridge (WR) 313 blocks using seismic and well data. Gas hydrate was discovered in these blocks in coarse- and fine-grained sediments during the 2009 Joint Industrial project (JIP) Leg 11 drilling expedition. Although the immediate interest of the exploration community is exclusively hydrate which is present in coarse–grained sediments, factors that control hydrate and free gas distribution in the two blocks and whether coarse and fine-grained hydrate-bearing units are related in any manner, formed the core of this research. The project spanned from 10/01/2012 to 07/31/2016. In the project, in both the leased blocks, the interval spanning the gas hydrate stability zone (GHSZ) was characterized using a joint analysis of sparse Ocean Bottom Seismic (OBS) and dense, surface–towed multichannel seismic (MCS) data. The project team had the luxury of calibrating their results with two well logs. Advance processing methods such as depth migration and full-waveform inversion (FWI) were used for seismic data analysis. Hydrate quantification was achieved through interpretation of the FWI velocity field using appropriate rock physics models at both blocks. The seismic modeling/inversion methodology (common to both GC955 and WR313 blocks) was as follows. First, the MCS data were depth migrated using a P-wave velocity (VP) model constructed using inversion of reflection arrival times of a few (four in both cases) key horizons carefully picked in the OBS data to farthest possible offsets. Then, the resolution of the traveltime VP model was improved to wavelength scale by inverting OBS gathers up to the highest frequency possible (21.75 Hz for GC955 and 17.5 for WR313) using FWI. Finally, the hydrate saturation (or the volume fraction) was estimated at the well location assuming one of the other hydrate morphology (filling the primary or the secondary porosity) was extrapolated out from the wells using the FWI VP as a guide. General outcomes were as follows. First and foremost, an imaging methodology using sparse seismic data, which is easily replicable at other sites with similar datasets, has been demonstrated. The end product of this methodology at both the leased blocks is quantitative estimates of hydrate distribution. Second, at both locations there is strong evidence that the base of the GHSZ, which does not appear as a clear Bottom Simulating Reflection (BSR), manifests in the VP perturbations created by FWI, suggesting that FWI is sensitive to subtle compositional changes in shallow sediments and establishes it as a valuable tool for investigations of hydrate-bearing basins. Third, through joint interpretation of the depth migrated image and the FWI VP model, how structure and stratigraphy jointly determine hydrate and free gas distribution in both blocks could be clearly visualized. The joint interpretation also suggests that the coarse and fine grained hydrate-bearing sediments at both leased are connected. Site specific results, in addition to general results, are as follows. At GC955 the overlying fine-grained hydrate-bearing unit could have been sourced from the underlying hydrate coarse-grained channel-levee complex through a chimney feature. The channel-levee system at GC955 is compartmentalized by faults, of which only a few may be impermeable. Although compartmentalized, the channel-levee system in the GC955 as a whole might be in communication except selected zones. At WR313 the overlying fine-grained fracture-filled hydrate unit appears to be sourced from below the GHSZ. The reason that only a particular fine-grained unit has hydrate, despite having lower porosity that the bounding units, could be the presence of secondary porosity (such as those formed from clay dewatering under compaction). In conclusion, the project was a pioneering effort in in joint analysis of OBS and MCS datasets for advancing the knowledge about a hydrate and free–gas system dynamics using advanced processing methods such as FWI and depth migration. Results obtained in this project can greatly advance the tools and techniques used for delineating specific hydrate prospects. Results obtained in this project can also be seamlessly incorporated into other DOE funded project on modeling the potential productivity and commercial viability of hydrate from sand-dominated reservoirs. The OBS and MCS data in this project were acquired in 2012 (after the JIP II drilling) by the USGS and therefore the results are a posteriori. Nonetheless, the seismic inversion workflow established through this project can be used to generate various what-if quantification scenarios even in absence of logs and serve as a valuable tool for guiding drilling operations. Results from this project can augment other DOE sponsored projects on determining the commercial viability of methane production from the Gulf of Mexico.

03 NATURAL GAS↗

Gas hydrate quantification in Walker Ridge block 313, Gulf of Mexico, from full-waveform inversion of ocean-bottom seismic data

The Gulf of Mexico (GOM) Joint Industry Project Leg 2 logging-while-drilling data in Walker Ridge lease block 313 (WR313) in the GOM detected gas hydrate in coarse- and fine-grained sediments at sites WR313-G and WR313-H. The coarse-grained units are thin ([Formula: see text]) and highly saturated, whereas the fine-grained unit is thick (approximately 200 m) with low saturation and fracture-filling gas hydrate. Unlike its coarse-grained counterpart, the seismic character of the fine-grained unit does not clearly indicate the presence of gas hydrate, which would likely have remained undiscovered in the absence of drilling. In this paper, through frequency-domain acoustic full-waveform inversion (FWI) of ocean-bottom seismometer data along a 2D multichannel seismic transect near sites WR313-G and WR313-H, we detect and quantify gas hydrate in the fine-grained unit. Key results are as follows: First, the base of the gas hydrate stability zone, which is not obvious in the reflection profile, can be discerned in the FWI results. Second, the gas hydrate in the fine-grained unit is mainly confined to the area between two sets of opposite-dipping normal faults implying that the fault architecture may be partially responsible for this gas hydrate accumulation and distribution.

Geochemistry & Geophysics↗

Basin and Petroleum System Modeling of Gas Hydrate Deposits in the Walker Ridge Area, Northern Gulf of Mexico - Poster

Poster presented by NETL at ICGH, 06/17 - Abstract:<p><br></p><p>We are currently constructing an Earth model of the Terrebonne Basin for comprehensive 3D modeling. Well data and a high-quality 3D seismic survey underpin the geologic conditions for the model. Additional model constraints include basal heat flow, seafloor temperature, and paleowater depth through time. Our initial investigation comprises the development of a “pseudo” 2D model centered on the deep WR313 #001 well. We are using this test case to establish the workflow for integrating BPSM with gas hydrate analyses; this will eventually be applied to the entire mini-basin. </p><p><br></p><p>A key aspect of investigating the gas hydrate system with BPSM is integrating it with the other active petroleum system(s) in the region, because the methane in hydrate deposits can derive from both biogenic and thermogenic sources. Some of the questions we may consider are: What is the history of these deposits with respect to the gas hydrate stability zone, recognizing that this area is not one characterized by simple continuous sedimentation and subsidence, but instead by periodic uplift, tilting, plate rotation, sea-level change, salt tectonics, and evolution of temperature gradients. </p><p><br></p><p>In conclusion, BPSM has been called the ‘great integrator’ in petroleum exploration. Development of a BPSM model of gas hydrates in the Terrebonne Basin of the northern GoM will provide a vehicle within which to integrate other early exploration and assessment research being conducted on gas hydrates, such as in frontier areas like Japan, as a potential resource likely to provide many decades of energy if proven to be commercially producible</p>

Dafov, Laura↗

Permeability and porosity of hydrate-bearing sediments in the northern Gulf of Mexico

Hydrate-bearing sands are being actively explored because they contain the highest concentrations of hydrate and are the most economically recoverable hydrate resource. However, relatively little is known about the mechanisms or timescales of hydrate formation, which are related to methane supply, fluid flux, and host sediment properties such as permeability. We used logging-while-drilling data from locations in the northern Gulf of Mexico to develop an effective medium theory-based model for predicting permeability based on clay-sized sediment fraction. The model considers permeability varying between sand and clay endpoint permeabilities that are defined from laboratory data. We verified the model using permeability measurements on core samples from three boreholes, and then used the model to predict permeability in two wells drilled in Walker Ridge Block 313 during the Gulf of Mexico Gas Hydrate Joint Industry Project Leg II expedition in 2009. We found that the cleanest sands (clay-sized fraction <0.05) had intrinsic (hydrate-free) permeability contrasts of 5-6 orders of magnitude with the surrounding clays, which is sufficient to provide focused hydrate formation due to advection of methane from a deep source or diffusion of microbial methane from nearby clay layers. In sands where the clay-sized fraction exceeds 0.05, the permeability reduces significantly and focused flow is less pronounced. In these cases, diffusion of dissolved microbial methane is most likely the preferred mode of methane supply for hydrate formation. In conclusion, our results provide important constraints on methane supply mechanisms in the Walker Ridge area and have global implications for evaluating rates of methane migration and hydrate formation in hydrate-bearing sands.

58 GEOSCIENCES↗

UT-GOM2-2 Drilling Fluid (Technical Note)

It is proposed that a salt-saturated, water-based mud might improve borehole stability for UT-GOM2-2 relative to a fresh-water-based mud. However, the primary objective for UT-GOM2-2 is to safely and successfully acquire uncompromised hydrate-bearing sediment cores. This can only be done if conditions stay within the hydrate stability zone, and well away from the hydrate stability boundary. The addition of salt to the drilling mud, shifts the hydrate stability boundary closer to estimated conditions. This shift, by some estimates of pressure and temperature, where conditions now fall outside of the hydrate stability zone, may result in borehole enlargement and the release of free gas into the borehole. This shift by all estimates, even when coring conditions stay inside the hydrate stability zone, shrinks the window between the estimated conditions and the hydrate stability boundary. This shift is likely to compromise the hydrate-bearing cores while they are being recovered from the bottom-hole to the rig floor. In this report we present two examples: 1) Assuming temperature and pressure from in-situ estimates: Hydrate within the target reservoirs (Orange and Blue) at Walker Ridge Block 313 (WR 313) will be outside the hydrate stability zone in the presence of a drilling mud with 9.5 wt.% salinity (the salinity of the proposed 10.5 ppg salt-based mud) at in situ pressure and temperature. Thus, the hydrate will be unstable. A 10.5 ppg salt-based mud may result in dissociation of the hydrate into its components: water and gas. 10.5 ppg salt-based mud may enlarge the borehole, release free gas into the borehole, and compromise the cores. 2) Assuming temperatures equal to the measured LWD borehole temperatures at this location: Hydrate within the target reservoirs will be stable with a salinity of 9.5 wt.% (the salinity of the proposed 10.5 ppg salt-based mud), but possibly unstable (just at the methane hydrate stability boundary) for a salinity of 17.2 wt.% (the salinity of the proposed 13.5 ppg salt-based kill mud). if the borehole has the same temperature as recorded during previous LWD drilling at this location. A 13.5 ppg salt-based kill mud may destabilize the borehole. More importantly, a 10.5 ppg salt-based mud does not provide a large enough window between the estimated conditions and the hydrate stability boundary. Core temperatures and pressures fluctuate from the bottom-hole conditions as the core is brought up from the bottom-hole to the rig floor. These fluctuations are likely to cause the hydrate in the cores to touch or cross the stability boundary. Therefore, cores captured using a 10.5 ppg salt-based mud are likely to be compromised during core recovery to the rig floor.

03 NATURAL GAS↗

Archie's Saturation Exponent for Natural Gas Hydrate in Coarse-Grained Reservoirs

Accurately quantifying the amount of naturally occurring gas hydrate in marine and permafrost environments is important for assessing its resource potential and understanding the role of gas hydrate in the global carbon cycle. Electrical resistivity well logs are often used to calculate gas hydrate saturations, S h , using Archie's equation. Archie's equation, in turn, relies on an empirical saturation parameter, n . Though n = 1.9 has been measured for ice–bearing sands and is widely used within the hydrate community, it is highly questionable if this n value is appropriate for hydrate–bearing sands. In this work, we calibrate n for hydrate–bearing sands from the Canadian permafrost gas hydrate research well, Mallik 5L–38, by establishing an independent downhole S h profile based on compressional–wave velocity log data. Using the independently determined S h profile and colocated electrical resistivity and bulk density logs, Archie's saturation equation is solved for n , and uncertainty is tracked throughout the iterative process. In addition to the Mallik 5L–38 well, we also apply this method to two marine, coarse–grained reservoirs from the northern Gulf of Mexico Gas Hydrate Joint Industry Project: Walker Ridge 313–H and Green Canyon 955–H. All locations yield similar results, each suggesting n ≈ 2.5 ± 0.5. Furthermore, for the coarse–grained hydrate bearing ( S h > 0.4) of greatest interest as potential energy resources, we suggest that n = 2.5 ± 0.5 should be applied in Archie's equation for either marine or permafrost gas hydrate settings if independent estimates of n are not available.

58 GEOSCIENCES↗

The evolution of seafloor venting from hydrate-sealed gas reservoirs

Here we use 3D seismic data to show that three rows of seafloor gas mounds can be traced downward to leak points that lie at the hydrate-gas contact within three individual dipping coarse-grained sand bodies in the Terrebonne Basin, Walker Ridge block 313, northern Gulf of Mexico. We predict the overpressure within the sand bodies by assuming that the gas pressure at the vent points equal the least principal stress. We interpret that free gas accumulates at the base of the hydrate stability zone, trapped by the overlying sand which has a high methane hydrate saturation. The free gas accumulates until the gas pressure at the base of the hydrate stability zone reaches the least principal stress in the overlying mudrock, whereupon hydraulic fractures form and fluids are vented to the surface. The warm rising fluids and perhaps localized exothermic formation of hydrate raise the local salinity and temperature. This process progressively shifts the base of the hydrate stability zone to shallower depths and dissociates the hydrate seal within the sand, which creates new leak points and results in the observed migration of the seafloor vents. Within the southwest corner of the Terrebonne Basin, this process has repeated multiple times within the Blue, Orange, and Green sands. Here this study shows how the hydrate stability zone can influence the location of fluid expulsion and in turn be affected by the warm, rising, saline fluids sealed by hydrate.

58 GEOSCIENCES↗

On the Importance of Advective Versus Diffusive Transport in Controlling the Distribution of Methane Hydrate in Heterogeneous Marine Sediments

The occurrence of methane hydrate in marine reservoirs often correlates with the physical properties of the host sediments. High hydrate saturations (>60% of the pore volume) found in association with coarser-grained strata have been attributed to both enhanced advective transport through more permeable sediment layers and to perturbations in phase equilibrium related to pore space geometry that results in increased diffusive transport. To assess the relative importance of these mechanism in controlling hydrate occurrence, we develop a 1-D model for hydrate growth along dipping, coarse-grained layers embedded in a fine-grained sediment package. We explicitly account for pore size effects on methane solubility and permeability-driven variations in fluid flux. We show how the vertical distribution of hydrate varies in response to changes in grain size and rates of fluid advection, sedimentation, and in situ methane production. We then use our model to simulate centimeter-scale variations in hydrate saturation observed at Walker Ridge Block 313, Hole H in the Gulf of Mexico. We find that the largest concentrations of hydrate are controlled by diffusion, while increased advective methane supply favors more distributed growth throughout high-permeability regions. Our results hold promise for using well log-derived estimates of hydrate saturation to infer sediment properties and the sources and rates of methane supply during reservoir emplacement.

58 GEOSCIENCES↗

Factors Controlling Short-Range Methane Migration of Gas Hydrate Accumulations in Thin Coarse-Grained Layers

Natural gas hydrate is often found in marine sediment in heterogeneous distributions in different sediment types. Diffusion may be a dominant mechanism for methane migration and affect hydrate distribution. We use a 1–D advection–diffusion–reaction model to understand hydrate distribution in and surrounding thin coarse–grained layers to examine the sensitivity of four controlling factors in a diffusion–dominant gas hydrate system. These factors are the particulate organic carbon content at seafloor, the microbial reaction rate constant, the sediment grading pattern, and the cementation factor of the coarse–grained layer. We use available data at Walker Ridge 313 in the northern Gulf of Mexico where two ~3–m–thick hydrate–bearing coarse–grained layers were observed at different depths. The results show that the hydrate volume and the total amount of methane within thin, coarse–grained layers are most sensitive to the particulate organic carbon of fine–grained sediments when deposited at the seafloor. The thickness of fine–grained hydrate free zones surrounding the coarse–grained layers is most sensitive to the microbial reaction rate constant. Furthermore, it may be possible to estimate microbial reaction rate constants at other locations by studying the thickness of the hydrate free zones using the Damköhler number. In addition, we note that sediment grading patterns have a strong influence on gas hydrate occurrence within coarse–grained layers.

54 ENVIRONMENTAL SCIENCES↗

Reactive transport modeling of organic carbon degradation in marine methane hydrate systems

Abstract Natural methane hydrate has often been observed in sand layers that contain no particulate organic carbon (POC), but are surrounded by organic-rich, fine-grained marine muds. In this paper, we develop a reactive transport model (RTM) of a microbially-mediated set of POC degradation reactions, including hydrolysis of POC driven by extracellular enzymes, fermentation of the resulting high-molecular weight dissolved organic carbon (HMW-DOC), and methanogenesis that consumes low-molecular weight dissolved organic carbon (LMW-DOC). These processes are mediated by two groups of microbes, fermenters and methanogens that are heterogeneously distributed in different lithologies, with the largest numbers of microbes in the large pores of coarse-grained layers. We find that the RTM can reproduce methane hydrate occurrences observed in two different geological environments, at Walker Ridge Site 313-H (Gulf of Mexico) and IODP Site U1325 (Cascadia Margin). We also find that microbes can degrade POC even if they are physically separated, as extracellular enzymes and DOC can diffuse away from where they are produced by microbes. Microbial activity is highest at relatively early times after burial at shallow depths and near lithological boundaries, where concentration gradients transport solutes to intervals that contain the most microbes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mechanisms for Methane Transport and Hydrate Accumulation in Coarse-Grained Reservoirs

The distribution of natural methane hydrate within high saturation reservoirs and mechanisms that control the migration of methane are an active area of research. In this project, we studied methane migration mechanisms and associated hydrate accumulation rates in coarse-grained sands of the Terrebonne Basin, located in Walker Ridge Block 313 (WR313), northern Gulf of Mexico. Hydrate in this area is distributed heterogeneously within ~900 m of methane hydrate stability zone, in both thick (10-25 m) and thin (< 3 m) sand layers, and in units of subvertical hydrate-filled fractures. We investigated hydrate formation from diffusively and advectively supplied methane using one-, two-, and three-dimensional basin modeling with inputs from well log and seismic data. The hydrate accumulations at WR313 can mostly be explained by short, diffusive migration of methane as well as short-range advective transport of methane from clays into neighboring coarser-grained layers. This is likely enhanced by small-scale lithologic variations, including local microbial methanogenesis in interbedded clays. Furthermore, our work shows overpressure in clay sediments surrounding sand reservoirs may enhance short-range diffusive migration. Long-range migration of dissolved methane and gas mainly influence hydrate saturation right at the base of the hydrate stability zone, although the dissolved phase can be channeled upwards along sands by compaction-driven flow. Capillary effects can allow gas bubbles to migrate appreciable distances above the predicted base of gas hydrate stability, possibly reaching a few tens of meters into the hydrate stability zone. Recycling methane from hydrate buried beneath the base of the hydrate stability zone can concentrate hydrate at large saturations within a few tens of meters of the base of hydrate stability.

58 GEOSCIENCES↗

Characterizing Baselines and Change in Gas Hydrate Systems using EM Methods

The objective of this project was to advance our understanding of gas hydrate systems in nature by characterizing their electrical properties in the field and in the laboratory. In the laboratory measurements, methane hydrate was synthesized from pure water ice and flash frozen seawater, with varying amounts of sand or silt added. Electrical conductivity was determined by impedance spectroscopy, using equivalent circuit modeling to separate the effects of electrodes and to gain insight into conduction mechanisms. Silt and sand increase the conductivity of pure hydrate, inferred to be contaminant NaCl contributing to conduction in hydrate, to a peak conductivity in agreement with peak resistivities observed in well logs through massive hydrate (3,000--10,000 Ωm). The addition of silt and sand lowers the conductivity of hydrate synthesized from seawater, by an amount consistent with Archie's Law. All samples were characterized using cryogenic scanning electron microscopy and energy dispersive spectroscopy, which shows good connectivity of salt and brine phases. Electrical conductivity measurements of pure hydrate and hydrate mixed with silt during pressure-induced dissociation supports previous conclusions that sediment increases dissociation rate. In order to characterize gas hydrate systems in the field, we collected 360 line kilometers of controlled-source electromagnetic data on Walker Ridge 313, Orca Basin (WR100), Mad Dog (GC781), and Green Canyon 955 in the Gulf of Mexico, all areas with known or seismically inferred gas hydrate deposits and which have be drilled or targeted for future drilling. We deep-towed an EM transmitter that generates an alternating electric field which propagates through the seafloor geology. Data were recorded on 6 receivers towed behind the transmitter at distances between 550 and 1550 m. In the presence of conductive geology, the electric fields will be attenuated, and conversely, in resistive geology the fields will be preserved. Our data were inverted using a 2D inversion method that first optimizes the model-data misfit, then finds the smoothest model fitting the data. This ensures that resistivity structures present in the final model are likely necessary. At each of the proposed drilling sites we found increased resistivity, interpreted as increased hydrate concentrations. However, not only were the primary drilling sites not always more resistive than the alternate sites, at WR313 the strongest resistors were not at the locations targeted for drilling.

03 NATURAL GAS↗

Prestack Waveform Inversion at GC 955: Trials and sensitivity of PWI to high-resolution seismic data (Data Report)

Understanding the spatial extent and variability of hydrate deposits has important implications for potential economic production, climate change, and assessing natural hazards risks. Seismic reflection techniques are capable of determining the extent of gas hydrate deposits and can shed light on hydrate concentrations and properties. Using high resolution prestack time migrated seismic data collected during a 2013 US Geological Survey expedition and prestack waveform inversion (PWI) techniques, we produce highly resolved velocity models and compare them to co-located well logs. Coupling our PWI results with velocity-porosity relationships and nearby well control, we compare hydrate properties at site 955 in the Green Canyon and site 313 at Walker Ridge.

03 NATURAL GAS↗