Search NASA⌕ Search

SEARCH · Search NASA

Results for “Weight reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Highly Anisotropic Drude-Weight-Reduction and Enhanced Linear-Dichroism in van der Waals Weyl Semimetal T d -MoTe 2 with Coherent Interlayer Electronic Transport

Weyl semimetal (WSM) states can be achieved by breaking spatial-inversion symmetry or time reversal symmetry. However, the anisotropy of the energy reduction contributing to the emergence of WSM states has seldom been investigated by experiments. A van der Waals metal MoTe 2 exhibits a type-II WSM phase below the monoclinic-to-orthorhombic-phase-transition temperature T c ~ 250 K. Here, in this work, a combined linearly polarized optical-spectroscopy and electrical-transport study of MoTe 2 is reported at different temperatures. The Drude components in the a-axis, b-axis, and c-axis optical conductivity spectra, together with the metallic out-of-plane and in-plane electrical resistivities, indicate the coherent inter-layer and in-plane charge transports. Moreover, the Drude weight in σ 1a (ω), rather than the Drude weights in σ 1b (ω) and σ 1c (ω), decreases dramatically below T c , which exhibits a highly anisotropic decrease in its Drude weight and thus suggests a strongly anisotropic reduction of the electronic kinetic energy in the WSM phase. Furthermore, below T c , due to the in-plane anisotropic spectral-weight transfer from Drude component to high-energy region, the in-plane inter-band-absorption anisotropy increases remarkably ≈770 meV, and has the largest value (≈0.68) of normalized linear dichroism among the reported type-II WSMs. The work sheds light on seeking new WSMs and developing novel photonic devices based on WSMs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Spectral weight reduction of two-dimensional electron gases at oxide surfaces across the ferroelectric transition

The discovery of a two-dimensional electron gas (2DEG) at the LaAlO 3 /SrTiO 3 interface has set a new platform for all-oxide electronics which could potentially exhibit the interplay among charge, spin, orbital, superconductivity, ferromagnetism and ferroelectricity. In this work, by using angle-resolved photoemission spectroscopy and conductivity measurement, we found the reduction of 2DEGs and the changes of the conductivity nature of some ferroelectric oxides including insulating Nb-lightly-substituted KTaO 3 , BaTiO 3 (BTO) and (Ca,Zr)-doped BTO across paraelectric-ferroelectric transition. We propose that these behaviours could be due to the increase of space-charge screening potential at the 2DEG/ferroelectric regions which is a result of the realignment of ferroelectric polarisation upon light irradiation. This finding suggests an opportunity for controlling the 2DEG at a bare oxide surface (instead of interfacial system) by using both light and ferroelectricity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Coupling of Flavonoid Initiation Sites with Monolignols Studied by Density Functional Theory

Lignin recalcitrance presents a challenge for the development of a bioeconomy that employs lignocellulosic feedstocks. The efficiency of lignin deconstruction is improved by a reduction of molecular weight, and given the discovery that flavones serve as initiation sites in lignin biosynthesis, these molecular weight reductions could potentially be achieved with plant metabolic engineering to over-express flavonoids. Upon increasing the flavonoid content in lignin, the bond strengths and properties of flavonoid-monolignol linkages become increasingly important. To that end, the current work applies density functional theory calculations to elucidate the bond dissociation enthalpies (BDEs) of flavonoid-monolignol linkages, including dimers with oxidized monolignols. Specifically, the dimer bond strengths and monomer hydrogen abstraction energies for the flavonoids tricin, chrysoeriol, luteolin, apigenin, catechin, epicatechin, epigallocatechin, and epigallocatechin gallate are calculated, when coupled to seven natural and engineered monolignols. Results indicate that 4'-O-ß linkage strengths between flavonoids and monolignols are of comparable strength to inter-monolignol ß-O-4 linkages, with average flavonoid-monolignol BDEs of 70.7 kcal/mol relative to ~69.3 kcal/mol in analogous canonical monolignols. Epigallocatechin yielded the lowest 4'-O-ß bond strength of 52.3 kcal/mol when coupled to an oxidized monolignol, while the flavones overall produced lower average BDEs, relative to the flavanols. Substituents at the 3'-C and 5'-C positions on flavonoids affected the dimer linkage strengths to a greater extent than glycosylation or substituents further from the linkage. Erythro and threo stereochemistry across the flavonoid-monolignol linkage library exhibited only small energetic differences and no pronounced correlations. Taken together, the predictions from this work support the concept that higher concentrations of flavonoid initiation sites in lignin may afford linkage properties conducive to more facile lignin depolymerization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Tailored Fiber Placement for Complex Preforms

Tailored Fiber Placement (TFP) offers a novel approach to optimize fiber architecture for the fabrication of complex, structural parts not traditionally suitable for advanced composites. This technology not only offers new routes for weight reduction via metal substitution, it also offers cost reduction through minimization of material scrap and reduced labor. This reduction in component weight leads to increased fuel efficiency, and reduced production energy consumption, thereby, helping to achieve the stated IACMI technical goals. This technology leverages centuries of manufacturing development in support of the textile and embroidery industry. One major drawback to this technology is the lack of commercial or non- proprietary structural performance data and robust analytical tools used to optimize fiber architecture and predict performance. This project was structured to utilize common sub-element features to validate analytical performance tools, generate performance data, and gather cost and performance data on components of interest. This project was designed to give industry sponsors the confidence and ability to take full advantage of TFP to fabricate primary, highly loaded structure and integrate features such as metallic fasteners. The project focused principally on the use of high strength carbon fiber, such as T700, and the use of aerospace epoxy resin matrix to primarily support development of new composite applications in vehicle, aerospace, and industrial markets. This project applied previously developed analytical tools to predict the performance of TFP produced parts. This work focused on developing the pipeline to characterize material in order to accurately predict component performance when modifying the TFP print paths and stitch density. This focused on experimental characterization via standardized ASTM testing, alongside experimental testing of more representative service components by testing curved beam strength, beam shear performance, a large scale TFP lug, and ultimately designing a fully TFP clip bracket that reduced weight and cost compared to a traditional metallic component. The new knowledge gained from this program included: 1) development and demonstration of novel analytical tools applied to analysis of TFP preforms; 2) development and demonstration of a building block approach using coupons and sub-elements to optimize the design of a more complex component; 3) demonstration that optimized fiber orientation using TFP can exceed performance of conventional textile composite materials and can open new applications currently limited to metallic components; 4) Demonstration of performance and cost benefits of the TFP process as compared to metallic and conventional textile composites. Recommendations for follow-on work include development of design allowables to assess the impact of high temperature/moisture exposure or saturation during loading, tracking the impact of stitching needle wear on the performance of parts and ability to stitch thicker preforms, using TFP preforms as local reinforcement at areas of bearing or complex loading, and topology optimization of components by tow steering. The expertise developed during the course of this project can be leveraged to provide commercial engineering design and fabrication services using TFP. UDRI is in the process of formalizing their partnership with Spintech, who will serve as the commercialization partner for this technology and provide molding services and deliver finished components to the end user. UDRI will continue to produce the preforms until the economics allow Spintech to procure its own TFP equipment or lease UDRI equipment, at which point UDRI will step away from manufacture and serve as the engineering and design lead on product development.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Next Generation High Efficiency Boosted Engine Concept

This report summarizes a collaborative research project between Ford Motor Company, FEV North America, and Oak Ridge National Laboratory to develop a next-generation, high-efficiency, boosted spark-ignited engine. The goal was to achieve a 23% improvement in fuel economy and a 15% reduction in engine weight compared to a 2016 Ford F150. The team utilized advanced technologies including a high compression ratio, cooled exhaust gas recirculation (EGR), early intake valve closing, and a novel active pre-chamber ignition system. The final engine prototype met the fuel economy goal and demonstrated a 4.3% weight reduction, with further opportunities identified to reach the full 15% target.

Fuel economy↗
DOE OSTI2020

Ultra-Light Hybrid Composite Door Design, Manufacturing and Demonstration

New Corporate Average Fuel Economy regulations require improved fuel efficiency of the future vehicle fleet. Weight reduction is key to achieving these targets. Replacing metallic body and chassis components with carbon fiber-reinforced composites offers the most weight reduction potential at up to 70%. Introduction of the BMW i3 and i8 in 2014 required mass production processes to meet 20,000+ units per year. Preforming with High Pressure Resin Transfer Molding has been implemented and meets rate, cost, and performance requirements. We will advance these technologies to develop an ultra-light driver’s side door for the vehicle with production rates of 40,000 units annually per plant in Detroit, Michigan. This project sought to employ a comprehensive systems approach for designing, manufacturing, and demonstrating an ultra-light hybrid composite automotive door. Composite structural components are integrated with other functional systems to reduce part count and full-system weight by a minimum of 42.5%. The approach will be demonstrated on a driver’s- side front door and will consider all fit, functional, safety, and cost requirements. These concepts will be evaluated using structural and crash simulations and linked to a manufacturing feasibility study, resulting in producible designs of an integrated door system. A cost model will evaluate part of the cost for the various designs and will ensure the cost target of less than $5 per pound of weight saved is met. Hybrid composites consisting of carbon, glass, and metal components will be included in our trade-off studies to satisfy these cost and performance goals.

02 PETROLEUM↗
DOE OSTI2025

Reducing Mass of Steel Auto Bodies using Thin Advanced High Strength Steel with Carbon-Fiber Reinforced Epoxy

Diversitak, a company based in Detroit, MI, has developed a proprietary, low specific gravity, carbon fiber-reinforced epoxy (CFRE) under U.S. patent number 9,963,58832. Preliminary testing on this new material conducted in collaboration with ArcelorMittal Steel Company proved out the CFRE concept. A thin layer of this CFRE was applied to a stamped sheet of steel with residual stamping oils from a mill, in a time corresponding to automotive processing (e.g., ~15 seconds), and processed following automotive e-coat procedures (phosphating + 175–200°C heating), to complete the curing. No problems with adherence or performance were noted. While the CFRE does add weight to a thin gauge steel panel, it weighs much less than what is displaced by using thicker conventional mild steel gauges. The application of the coating showed a significant increased dent resistance, oil canning resistance, and part stiffness.This current two-year project was designed to mature this new technology to near manufacturing readiness to reduce the weight of a vehicle and lower the cost of weight reduction. The process involves the use of thinner gauge steels than are currently used. The collaborative development team included two industrial manufacturers: Diversitak and ArcelorMittal Steel Company; LightMAT; and two National Laboratories: Oak Ridge National Laboratory (ORNL) and Idaho National Laboratory (INL). The team developed a new manufacturing process to reduce the weight of a vehicle and lower the cost of weight reduction, as well as a better understanding of how to apply the coating so that it will perform to a high standard in-service. The team also performed an in-depth study to determine the long-term durability of the materials manufactured using this technology and well-known automotive industry standard tests.The overall process involved stiffening the thinner gauge steel by applying the CFRE on only one side. To accomplish this goal, the optimal reinforcement fiber length and fiber concentration was first determined. This was followed by measuring the coefficient of thermal expansion (CTE) in all three directions, so it could be fed into manufacturing models and methods for rapidly and inexpensively applying the coating. This was followed by panel level evaluations of the coating and steel combination, and then by full part demonstration of the technology on door panels. The final step was corrosion testing of the parts.ArcelorMittal characterized the advanced high strength steel (AHSS) (e.g., metallurgy-heat treatment for required AHSS properties as a function of the sheet thickness, state of internal stress) and quantified CFRE adhesion to the steel as a function of sheet preparation (e.g., rolling and stamping).ORNL optimized the fiber length, fiber concentration, and coating thickness for best vehicle function and performance at the least cost. Along with the suppliers, ORNL developed a durable CFRE application process (e.g., gun material, design, robotic dispensing process) and identified the adhesion stability of the CFRE during process holding. An approach to ensure that application/curing timing conforms to conventional assembly line speed and plant cycle times was determined. ORNL also determined the CTE of the material in all three directions and performed material scanning electron microscopy (SEM) analyses.INL characterized the corrosion properties of the steel panels coated with CFRE. The panels were investigated for corrosion resistance and stability as replacement materials used in automotive body panels to reduce mass. The coupons tested at INL were supplied by Diversitak after an optimized CFRE formulation was achieved in the already coated form for corrosion testing.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

A novel digital lifecycle for Material‐Process‐Microstructure‐Performance relationships of thermoplastic olefins foams manufactured via supercritical fluid assisted foam injection molding

Abstract This research significantly enhances the applicability of thermoplastic olefins (TPOs) in the automotive industry using supercritical N 2 as a physical foaming agent, effectively addressing the limitations of traditional chemical agents. It merges experimental results with simulations to establish detailed material‐process‐microstructure‐performance (MP2) relationships, targeting 5–20% weight reductions. This innovative approach labeled digital lifecycle (DLC) helps accurately predict tensile, flexural, and impact properties based on the foam microstructure, along with experimentally demonstrating improved paintability. The study combines process simulations with finite element models to develop a comprehensive digital model for accurately predicting mechanical properties. Our findings demonstrate a strong correlation between simulated and experimental data, with about a 5% error across various weight reduction targets, marking significant improvements over existing analytical models. This research highlights the efficacy of physical foaming agents in TPO enhancement and emphasizes the importance of integrating experimental and simulation methods to capture the underlying foaming mechanism to establish material‐process‐microstructure‐performance (MP2) relationships. Highlights Establishes a material‐process‐microstructure‐performance (MP2) for TPO foams Sustainably produces TPO foams using supercritical (ScF) N 2 with 20% lightweighting Shows enhanced paintability for TPO foam improved surface aesthetics Digital lifecycle (DLC) that predicts both foam microstructure and properties DLC maps process effects & microstructure onto FEA mesh for precise prediction

Engineering↗
DOE OSTI2024

Next Gen High Efficiency Boosted Engine Development

This work represents an advanced engineering research project partially funded by the U.S. Department of Energy (DOE). Ford Motor Company, FEV North America, and Oak Ridge National Laboratory collaborated to develop a next generation boosted spark ignited engine concept. The project goals, specified by the DOE, were 23% improved fuel economy and 15% reduced weight relative to a 2015 or newer light-duty vehicle. The fuel economy goal was achieved by designing an engine incorporating high geometric compression ratio, high dilution tolerance, low pumping work, and low friction. The increased tendency for knock with high compression ratio was addressed using early intake valve closing (EIVC), cooled exhaust gas recirculation (EGR), an active pre-chamber ignition system, and careful management of the fresh charge temperature. Engine weight reduction measures were implemented throughout the engine system making use of composite materials, advanced manufacturing techniques, and architectural choices. This report outlines the analytical, design, fabrication, and test work conducted for the duration of the project. The combustion system stability, EGR tolerance, and knock resistance were validated on a single cylinder engine. An inline six-cylinder engine was then designed targeting application in the Ford F150. Multi-cylinder engines were produced and tested achieving the target vehicle fuel economy improvement of 23% assessed using measured engine fuel consumption combined with a vehicle drive cycle simulation. Actions were identified and designs were demonstrated to achieve the 15% weight reduction target. This project included items covering a range of technology readiness levels. Some of the technologies explored are production ready, while others were investigated to understand the limitations for what can be achieved in a stoichiometric, gasoline-fueled, spark-ignited internal combustion engine.

42 ENGINEERING↗
DOE OSTI2022

Development and Demonstration of a Fuel-Efficient, Class 8 Tractor & Trailer Engine System (SuperTruck II)

Navistar presents the SuperTruck II (ST II) Final Report to the Unites States Department of Energy (US DOE), which covers the five Budget Periods (BPs) from 10-1-2016 through 6-30-2022. For ST II, Navistar built on the achievements of the SuperTruck I (ST I) Program as a catalyst to continue critical research, design and development, testing, and operations to reach the ambitious goals of the ST II project. This approach allowed Navistar to continue contributing to the essential needs of our nation for safe, efficient, and cost-effective delivery of goods and services, as we reduced negative environmental effects and improved operational productivity. This document contains information specified in DOE F 4600.2, Final Scientific/Technical Report DOE F 241.3, B. SCIENTIFIC/TECHNICAL REPORTS, explaining how we met and exceeded program requirements. Throughout this Final Report, Navistar extracted information from documents prepared during the project that represent our management, design and development, building, and testing efforts to meet and exceed SuperTruck II project goals. Navistar followed Plan requirements to achieve / exceed Project Objectives: a) >100% improvement in vehicle freight efficiency (FE) (on ton-MPG basis) relative to 2009 baseline with stretch goal of 140% improvement [actual: 170%); b) >55% engine brake thermal efficiency (BTE) demonstrated in operational engine at a 65-mph cruise point on a dynamometer – ≥31% increase from 2009 baseline [actual: 55.20% of combined BTE) ; and c) development and implementation of commercially cost effective technologies (in terms of a simple payback). Technology selection / development path focused on developing technologies applicable for production within 3-year approach, while ensuring technology readiness and cost of ownership for end users. The Program was organized into five budget periods: Requirements / Technology Assessment and Initial Hardware Testing; Technology Development and Concept Readiness Demonstration; Technology Finalization and Validation Tractor / Trailer Fabrication, Integration and Commissioning Demonstration; and Fuel Economy (FE) and Brake Thermal Efficiency (BTE) and Program Completion. Leadership was provided by DOE, with tasks performed by laboratories (Argonne National Laboratory, Lawrence Livermore National Laboratory); partners at Bosch, TPI, Dana, and J.B. Hunt; , and support from University of Michigan and Clemson University. Navistar lead this team with Principal Investigator / Contracting Officer; Project Manager (PM); Vehicle, Engine, and Aftertreatment Engineers; Finance Manager, Technical Program Leads, and Legal/IP; and other key personnel. Work also included personnel in risk management; funding / budget / finance. Work involved analysis, development, testing, and down selection of individual/system engine, aftertreatment, and vehicle technologies, with integration of selected technologies into a prototype vehicle for demonstration of fuel-efficiency gain. Work also included component/integrated system level development of truck and trailer aerodynamics, base engine efficiency, advanced aftertreatment, combustion efficiency, waste heat recovery, hybrid powertrain, reduced rolling resistance, weight reduction, idle reduction, and driver feedback. As ST II progressed, Navistar performed computer-based modeling / simulations of technologies focused on the primary operational areas: Engine, Aftertreatment, and Vehicle. During the ST II Program, the COVID Virus outbreak unexpectedly challenged by the effects of, which affected staffing, scheduling, design, supplies, availability of materials, production procedures, and testing. The DOE responded by extending the program by three quarters to ensure that project tasks were completed for this vital project. Focus continued on analyzing, developing, testing, and down selecting individual-/system-level engine and vehicle technologies for integration of the final selected technologies into a prototype vehicle that would demonstrate fuel-efficiency gains made possible through these technologies. This included component/integrated system-level development of truck and trailer aerodynamics, base engine efficiency, advanced aftertreatment, combustion efficiency, waste heat recovery, solar power, distributed and intelligent vehicle power, hybrid powertrain, reduced rolling resistance, weight reduction, idle reduction, and driver feedback. Throughout the program, function, reliability, and performance at all levels were ensured through testing. Proof of this approach was demonstrated in multiple, on-road demonstrations: Scenario A (Flatland) Fuel Economy, Scenario B (Hilly) Fuel Economy, and City Cycle Tests. Other benefits derived from ST II included new/improved products, publications, patents, and next-step capabilities related to electric/hydrogen vehicles and autonomous driving.

Zukouski, Russ↗
DOE OSTI2021

Corrosion Protection and Dissimilar Material Joining for Next Generation Lightweight Vehicles

The Arconic Technology Center working with Honda R&D Americas, LLC and the Ohio State University evaluated the corrosion performance of several multi-material conditions and demonstrated the production worthiness of the Resistance Spot Riveting (RSR™) process. RSR is a new technology being developed by Howmet Fastening Systems (formerly Arconic, Inc.) that employs a fastener that is installed using conventional resistance spot welding equipment to produce multi-material joints. The goal of the 3-year project was to demonstrate the use of RSR to join aluminum to steel and aluminum to carbon fiber composites on a prototype scale. Deployment of this technology would help the automotive industry achieve an additional 10 to 20% weight reduction over high strength steels. These weight-savings to the body in white generally translates to 2.5-5.0% of overall vehicle curb weight. The resulting total weight-savings could provide a 1.5% to 3.0% total improvement in fuel efficiency for vehicles that incorporate RSR for multi-material joining. The RSR technology addresses several production barriers to achieving DOE’s fuel efficiency targets including eliminating the need of additional capital for new joining technologies and the flexibility to process conventional steel and multi-material structures with the same equipment. Additionally, the trend towards ultra-high strength steels limits the availability of conventional joining technologies that can effectively process these multi-material combinations. In order to accomplish these goals, the following program milestones were completed by the team: 1) Developed RSR process parameters, producing multi-material joints for mechanical testing and corrosion assessments. 2) Conducted corrosion evaluation of RSR and baseline joints assembled between automotive type aluminum alloys, steels, and carbon fiber using several corrosion mitigation strategies. 3) Developed a production ready feed system and integrate into a robotic resistance spot welding station to simulate automotive production conditions. 4) Produced demonstration assemblies for testing and evaluation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Implementation of Smart Materials for Actuation of Traditional Valve Technology for Hybrid Energy Systems

The ever-changing nature of the power industry will require the implementation of hybrid energy systems. Integration of tightly coupled components in hybrids often involves the diversion of exhaust gas flow. An innovative smart material actuation technology is proposed to replace traditional electro-mechanical actuated valve mechanisms with lighter and less expensive actuators. A shape memory alloy (SMA) spring-actuated valve was designed for high-temperature service to demonstrate the promise of smart materials in control valve applications. With SMA springs only generating a maximum force of 3.2 N, an innovative valve design was necessary. To demonstrate the concept, a 3-inch Nominal Pipe Size valve was designed, and 3D printed using the stereolithography technique. Increasing the electrical current to actuate the SMA springs reduced actuation time. The maximum current of 10 A produced the lowest actuation time of 2.85 s, with an observed maximum stroke rate of more than 100 stroke completion %/s (considering actuation open/close as 100% stroke) at the midrange. The final assembly of the valve was estimated to provide a cost reduction of more than 30% and a weight reduction of more than 80% compared to the other available automatic valves in the present market.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Solid-State Joining of Magnesium Sheet to High-Strength Steel

Increasing the use of lightweight materials and implementing enabling manufacturing technologies are the two primary paths toward automotive weight reduction. In many situations, the ability to substitute light weight material requires a need to attach and join light weight material to existing steel substructures requiring dissimilar joining technologies. Dissimilar joining methods currently available in cost range for high volume automotive manufacturing face multiple challenges. The problem is exacerbated in the case of Magnesium alloy to steel joints because of their highly dissimilar nature and lack of mutual miscibility. Additionally, Magnesium’s poor room temperature ductility complicates the use of point fastening technologies. Two emerging solid-state joining technologies Friction Stir assisted Scribe welding (FaST) and Ultrasonic Welding (USW) that employ large amount of plastic deformation at the interface were used to investigate, develop, and understand dissimilar joints between Magnesium Alloy to DP590 Steel. Various process responses including interface temperatures, process forces, strain fields were captured during the development of the welding process. Variety of welded samples were tested and characterized to understand the relationship between welding conditions and joints microstructure and mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Experimental and computational study of polystyrene sulfonate breakdown by a Fenton reaction

Experimental studies and ab initio quantum chemistry calculations were combined to investigate the process by which a Fenton reaction breaks down polystyrene sulfonate. The experimental results show that both molecular weight reduction and loss of aromaticity occur nearly simultaneously, a finding that is supported by the calculations. The results show that more than half of the material is broken down to low molecular weight compounds (< 500 g/mol) with two molar equivalents of H 2 O 2 per styrene monomer. The calculations provide insights into the reaction pathways and indicate that at least two hydroxyl radicals are required to cleave backbone Csingle bondC bonds or to eliminate aromaticity. The calculations also show that, of the aromatic carbons, hydroxyl radical is most likely to add to the carbon bonded to sulfur. This finding explains the loss of hydrogen sulfite anion early in the process and also the efficient reduction of Fe(III) to Fe(II) through semiquinone formation. Taken together the experimental and computational results indicate that the reaction is very efficient and that very little H 2 O 2 is lost to unproductive reactions. In conclusion, this high efficiency is attributed to the close association of Fe atoms with the sulfonate group such that hydroxyl radicals are generated near the polymer chains.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Synchrotron experiment and simulation studies of magnesium-steel interface manufactured by impact welding

The effective weight reduction in the automotive industry by the wide adoption of lightweight magnesium (Mg) alloys demands high-quality joint between magnesium alloys and massively-used steels in order to wring the excess weight with strength and safety assurance. However, Mg-steel joint is difficult to achieve because there is no mutual solubility between magnesium and steel and huge disparity in physical properties. An impact-based welding method recently showed successful Mg-steel joining. In this work, the characteristics of Mg-steel interface joined by the impact welding method were investigated. Synchrotron high-energy X-ray computed tomography and diffraction were applied to characterize the microstructure across Mg-steel interface. Results revealed a deposit layer formed at the joint interface where Fe-rich particles spread deep into the Mg matrix. High-resolution 3D morphology of Mg-steel interface demonstrated the trapped pores and cracks inside the deposit layer. Finally, the formation of the deposit layer and the void/cracking evolution were analyzed by using finite element models. These findings provide insights into the immiscible Mg-steel joining process.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Functionally Designed Ultra-Lightweight Carbon Fiber Reinforced Thermoplastic Composites Door Assembly (Final Scientific/Technical Report)

This is the final technical report for a project that developed an ultra-lightweight carbon fiber reinforced thermoplastics composite door assembly for a mid-size SUV. The project was able achieve a weight reduction of at least 42.5% while maintaining or exceeding the fit, function, safety, stiffness, and crash performance requirements of the current baseline door. Additionally, the target cost was set at less than $5 per pound of weight saved. To accomplish these goals, the project team employed a systems approach that involves redesigning the door assembly, exploring novel materials, optimizing the design, and utilizing advanced manufacturing technologies.

42 ENGINEERING↗
DOE OSTI2024

Evaluation of Composite Structural Materials for Heliostat Cost Reduction

Structures manufactured from steel comprise up to 40% of a CSP heliostat's cost. Composite structures represent a potential opportunity to reduce this cost. A reference heliostat structural model has been created with a reflector area of 25m 2 . The design, constructed of low-carbon steel, pro-vides baseline deflection and stiffness under a 21 m/s operating wind speeds. Wind loads on the tracker structure are determined for both operating and stow conditions. An established roster of suitable metal alternative materials is considered including: glass, basalt, and carbon reinforced polymer (GFRP, BFRP, and CFRP respectively). Three heliostat components are investigated: the pylon, torque tube, and the purlin-strut assembly. Composite material properties are substituted for those of steel, and the beams are re-sized to match the original steel components' deflection under given wind loads. Weight and cost changes resulting from this resizing are evaluated. It is found that GFRP and BFRP represent a 3X–6X cost premium for the same operating deflection character-istics as steel across all three investigated component classes; with weight reduction only achieved for the purlin-strut assembly. While CFRP components can achieve approximately 25–75% weight savings depending on the application, this comes with a 9X–14X cost increase over the steel base-line for tube-type structures and roughly 5X cost increase when replacing c-channel structures. This work does not rule out the possibility of cost savings when the heliostat design and kinematics to take advantage of composites' specific properties.

14 SOLAR ENERGY↗
DOE OSTI2020

Nucleophilic Thiols Reductively Cleave Ether Linkages in Lignin Model Polymers and Lignin

Lignin may serve as a renewable feedstock for the production of chemicals and fuels if mild, scalable processes for its depolymerization can be devised. The use of small organic thiols represents a bioinspired strategy to cleave the β–O–4 bond, the most common linkage in lignin. In the present study, synthetic β–O–4 linked polymers were treated with organic thiols, yielding up to 90 % cleaved monomer products. Lignin extracted from poplar was also treated with organic thiols resulting in molecular weight reductions as high as 65 % (Mn) in oxidized lignin. Thiol–based cleavage of other lignin linkages was also explored in small–molecule model systems to uncover additional potential pathways by which thiols might depolymerize lignin. The success of thiol–mediated cleavage on model dimers, polymers, and biomass–derived lignin illustrates the potential utility of small redox–active molecules to penetrate complex polymer matrices for depolymerization and subsequent valorization of lignin into fuels and chemicals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗