Search NASA⌕ Search

SEARCH · Search NASA

Results for “X-57”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

X-57 Power and Command System Design

This paper describes the power and command system architecture of the X-57 Maxwell flight demonstrator aircraft. The X-57 is an experimental aircraft designed to demonstrate radically improved aircraft efficiency with a 3.5 times aero-propulsive efficiency gain at a "high-speed cruise" flight condition for comparable general aviation aircraft. These gains are enabled by integrating the design of a new, optimized wing and a new electric propulsion system. As a result, the X-57 vehicle takes advantage of the new capabilities afforded by electric motors as primary propulsors. Integrating new technologies into critical systems in experimental aircraft poses unique challenges that require careful design considerations across the entire vehicle system, such as qualification of new propulsors (motors, in the case of the X-57 aircraft), compatibility of existing systems with a new electric power distribution bus, and instrumentation and monitoring of newly qualified propulsion system devices.

electric propulsion↗
NASA NTRS2017

Computational Analysis of a Wing Designed for the X-57 Distributed Electric Propulsion Aircraft

A computational study of the wing for the distributed electric propulsion X-57 Maxwell airplane configuration at cruise and takeoff/landing conditions was completed. Two unstructured-mesh, Navier-Stokes computational fluid dynamics methods, FUN3D and USM3D, were used to predict the wing performance. The goal of the X-57 wing and distributed electric propulsion system design was to meet or exceed the required lift coefficient 3.95 for a stall speed of 58 knots, with a cruise speed of 150 knots at an altitude of 8,000 ft. The X-57 Maxwell airplane was designed with a small, high aspect ratio cruise wing that was designed for a high cruise lift coefficient (0.75) at angle of attack of 0deg. The cruise propulsors at the wingtip rotate counter to the wingtip vortex and reduce induced drag by 7.5 percent at an angle of attack of 0.6deg. The unblown maximum lift coefficient of the high-lift wing (with the 30deg flap setting) is 2.439. The stall speed goal performance metric was confirmed with a blown wing computed effective lift coefficient of 4.202. The lift augmentation from the high-lift, distributed electric propulsion system is 1.7. The predicted cruise wing drag coefficient of 0.02191 is 0.00076 above the drag allotted for the wing in the original estimate. However, the predicted drag overage for the wing would only use 10.1 percent of the original estimated drag margin, which is 0.00749.

Deere, Karen A.↗
NASA NTRS2017

Design of the Cruise and Flap Airfoil for the X-57 Maxwell Distributed Electric Propulsion Aircraft

A computational and design study on an airfoil and high-lift flap for the X-57 Maxwell Distributed Electric Propulsion (DEP) testbed aircraft was conducted. The aircraft wing sizing study resulted in a wing area of 66.67 sq ft and aspect ratio of 15 with a design requirement of V(stall) = 58 KEAS, at a gross weight of 3,000 lb. To meet this goal an aircraft C(L,max) of 4.0 was required. The design cruise condition is 150 KTAS at 8,000 ft. This resulted in airfoil requirements of c(l) is approximately 0.90 for the cruise condition at Re = 2.35 x 10 (exp 6). A flapped airfoil with a c(l,max) of approximately 2.5 or greater, at Re = 1.0 x 10 (exp 6), was needed to have enough lift to meet the stall requirement with the DEP system. MSES computational analyses were conducted on the GAW-1, GAW-2, and the NACA 5415 airfoil sections, however they had limitations in either high drag or low c(l,max) on the cruise airfoil, which was the impetus for a new design. A design was conducted to develop a low drag airfoil for the X-57 cruise conditions with high c(l,max). The final design was the GNEW5BP93B airfoil with a minimum drag coefficient of c(d) = 0.0053 at c(l) = 0.90 and achieved laminar flow back to 69% chord on the upper surface and 62% chord on the lower surface. With fully turbulent flow, the drag increases to c(d) = 0.0120. The predicted maximum lift with turbulent flow is a c(l,max) of 1.95 at alpha = 19 deg. The airfoil is characterized by relatively flat pressure gradient regions on both surfaces at alpha = 0 deg, and aft camber to get extra lift out of the lower surface concave region. A 25% chord slotted flap was designed and analyzed with MSES for a 30 deg flap deflection. Additional 30 deg and 40 deg flap deflection analyses for two flap positions were conducted with USM3D using several turbulence models, for two angles of attack, to assess near c(l,max) with varied flap position. The maximum c(l) varied between 2.41 and 3.35. An infinite-span powered high-lift study was conducted on a GAW-1 constant chord 40 deg flapped airfoil section with FUN3D to quantify the airfoil lift increment that can be expected from a DEP system. The 16.7 hp/propeller blown wing increases the maximum C(L) from 3.45 to C(L) = 6.43, which is an effective q ratio of 1.86. This indicates that if the unblown high-lift flapped airfoil of the X-57 airplane achieves a c(l,max) of 2.78, then the high-lift augmentation blowing could yield a sectional lift coefficient of approximately 4.95 at c(l,max). Finally, a computational study was conducted with FUN3D on an infinite-span constant chord GAW-1 cruise airfoil to determine the impact of high-lift propeller diameter to wing chord ratio on the lift increment of the DEP system. A constant diameter propeller and nacelle size were used in the study. Three computational grids were made with airfoil chords of 0.5*chord, 1.0*chord, and 2.0*chord. Results of the propeller diameter to wing chord ratio study indicated that the blown to unblown C(L) ratio increased as the chord was decreased. However, because of the increase in relative size of the high-lift nacelle to the wing, which impacted wing lift performance, the study indicated that a propeller diameter to wing chord ratio of 1.0 gives the overall best maximum lift on the wing with the DEP system.

Viken, Jeffrey K.↗
NASA NTRS2017

Steady State Thermal Analyses of SCEPTOR X-57 Wingtip Propulsion

Electric aircraft concepts enable advanced propulsion airframe integration approaches that promise increased efficiency as well as reduced emissions and noise. NASA's fully electric Maxwell X-57, developed under the SCEPTOR program, features distributed propulsion across a high aspect ratio wing. There are 14 propulsors in all: 12 high lift motor that are only active during take off and climb, and 2 larger motors positioned on the wingtips that operate over the entire mission. The power electronics involved in the wingtip propulsion are temperature sensitive and therefore require thermal management. This work focuses on the high and low fidelity heat transfer analysis methods performed to ensure that the wingtip motor inverters do not reach their temperature limits. It also explores different geometry configurations involved in the X-57 development and any thermal concerns. All analyses presented are performed at steady state under stressful operating conditions, therefore predicting temperatures which are considered the worst-case scenario to remain conservative.

Thermal↗
NASA NTRS2018

Development of a Multi-Phase Mission Planning Tool for NASA X-57 Maxwell

The physical design and operation of electric aircraft like NASA Maxwell X-57 are significantly different than conventionally fueled aircraft. Operational optimization will require close coupling of aerodynamics, propulsion, and power. To address the uncertainty of electric aircraft operation, a system level Mission Planning Tool is developed to simulate all aircraft trajectory phases: taxi, motor run-up, takeoff, climb, cruise, and descent. The Mission Planning Tool captures performance parameters at each point of the trajectory including battery state of charge, the temperatures of components in the electrical system, and propulsion system thrust. This work describes the modeling of each mission phase, and compares the results of simulating a user-specified trajectory, and using a collocated optimal control approach to determine an optimal trajectory. The results show that optimization of the mission show a significant increase in the final battery state of charge over the user- specified simulation strategy. These results will inform the operation of the NASA Maxwell X-57 test flights that will take place this year.

Schnulo, Sydney L.↗
NASA NTRS2017

Transient Thermal Analyses of Passive Systems on SCEPTOR X-57

As efficiency, emissions, and noise become increasingly prominent considerations in aircraft design, turning to an electric propulsion system is a desirable solution. Achieving the intended benefits of distributed electric propulsion (DEP) requires thermally demanding high power systems, presenting a different set of challenges compared to traditional aircraft propulsion. The embedded nature of these heat sources often preclude the use of traditional thermal management systems in order to maximize performance, with less opportunity to exhaust waste heat to the surrounding environment. This paper summarizes the thermal analyses of X-57 vehicle subsystems that don't employ externally air-cooled heat sinks. The high-power battery, wires, high-lift motors, and aircraft outer surface are subjected to heat loads with stringent thermal constraints. The temperature of these components are tracked transiently, since they never reach a steady-state equilibrium. Through analysis and testing, this report demonstrates that properly characterizing the material properties is key to accurately modeling peak temperature of these systems, with less concern for spatial thermal gradients. Experimentally validated results show the thermal profile of these systems can be sufficiently estimated using reduced order approximations.

Thermal Analyses↗
NASA NTRSDate not supplied

Battery Evaluation Profiles for X-57 and Future Urban Electric Aircraft

Battery energy density is one of the most critical design parameters for sizing all-electric aircraft, however it’s easily overestimated. Establishing the effective, usable energy density is confused by varying degrees of margin needed to account for structural and thermal management between different cell chemistry and pack designs. Therefore, a better methodology is needed to fairly compare emerging battery technologies for electric aircraft. Currently, there is a loss of critical information when vehicle trade studies are performed using “nominal” published cell-level performance metrics. Aircraft power demands rarely match these nominal power profiles, and aircraft designers lack the ability to accurately simulate the battery performance and temperature off-nominally unless the battery chemistry is well established. Conversely, battery suppliers have no generalized reference cases to publish more realistic performance metrics. This can lead to poor assumptions, such as aircraft studies assuming a fixed discharge efficiency of a battery, when in reality the usable energy in a pack is dependent on the power and thermal profile. Information needed to properly assess weight penalties for thermal management is also typically poorly characterized when assessing candidate batteries. This paper serves to better inform battery development, and similarly, provide aircraft designers with more realistic assumptions for applying knockdown margins in their designs. Detailed power and thermal performance estimates are provided, which provide a starting point for sizing power and thermal budgets using experimentally derived battery models. Results show that the X-57 battery-to-shaft efficiency is 77.3% for a particular optimized mission. Considering a 25% reserve on the battery capacity, this means that only roughly half of the original 55.3kWh ‘nominal’ pack energy can be converted to useful work during a mission. Further estimates on a clean-sheet VTOL optimization show an average 82.7% battery-to-shaft efficiency, using 98% peak efficiency inverters and 97.4% peak efficiency motors. Although higher battery efficiencies are possible, the resulting weight penalty negates improvement in vehicle performance. These trade-offs and resulting power profiles are provided as a starting point to better assess future battery designs.

Battery↗
NASA NTRS2017

Comparison of High-Fidelity Computational Tools for Wing Design of a Distributed Electric Propulsion Aircraft

A variety of tools, from fundamental to high order, have been used to better understand applications of distributed electric propulsion to aid the wing and propulsion system design of the Leading Edge Asynchronous Propulsion Technology (LEAPTech) project and the X-57 Maxwell airplane. Three high-fidelity, Navier-Stokes computational fluid dynamics codes used during the project with results presented here are FUN3D, STAR-CCM+, and OVERFLOW. These codes employ various turbulence models to predict fully turbulent and transitional flow. Results from these codes are compared for two distributed electric propulsion configurations: the wing tested at NASA Armstrong on the Hybrid-Electric Integrated Systems Testbed truck, and the wing designed for the X-57 Maxwell airplane. Results from these computational tools for the high-lift wing tested on the Hybrid-Electric Integrated Systems Testbed truck and the X-57 high-lift wing presented compare reasonably well. The goal of the X-57 wing and distributed electric propulsion system design achieving or exceeding the required 𝐶 (sub L) = 3.95 for stall speed was confirmed with all of the computational codes.

Deere, Karen A.↗
NASA NTRS2017

Comparison of Aero-Propulsive Performance Predictions for Distributed Propulsion Configurations

NASA's X-57 "Maxwell" flight demonstrator incorporates distributed electric propulsion technologies in a design that will achieve a significant reduction in energy used in cruise flight. A substantial portion of these energy savings come from beneficial aerodynamic-propulsion interaction. Previous research has shown the benefits of particular instantiations of distributed propulsion, such as the use of wingtip-mounted cruise propellers and leading edge high-lift propellers. However, these benefits have not been reduced to a generalized design or analysis approach suitable for large-scale design exploration. This paper discusses the rapid, "design-order" toolchains developed to investigate the large, complex tradespace of candidate geometries for the X-57. Due to the lack of an appropriate, rigorous set of validation data, the results of these tools were compared to three different computational flow solvers for selected wing and propulsion geometries. The comparisons were conducted using a common input geometry, but otherwise different input grids and, when appropriate, different flow assumptions to bound the comparisons. The results of these studies showed that the X-57 distributed propulsion wing should be able to meet the as-designed performance in cruise flight, while also meeting or exceeding targets for high-lift generation in low-speed flight.

Borer, Nicholas K.↗
NASA NTRS2017

Whirl Flutter Stability and Its Influence on the Design of the Distributed Electric Propeller Aircraft X- 57

This paper studies the whirl flutter stability of the NASA experimental electric propulsion aircraft designated the X-57 Maxwell. whirl flutter stability is studied at two flight conditions: sea level at 2700 RPM to represent take-off and landing and 8000 feet at 2250 RPM to represent cruise. Two multibody dynamics analyses are used: CAMRAD II and Dymore. The CAMRAD II model is a semi-span X-57 model with a modal representation for the wing/pylon system. The Dymore model is a semi-span wing with a propeller composed of beam elements for the wing/pylon system that airloads can be applied to. The two multibody dynamics analyses were verified by comparing structural properties between each other and the NASTRAN analysis. For whirl flutter, three design revisions of the wing and pylon mount system are studied. The predicted frequencies and damping ratio of the wing modes show good agreements between the two analyses. Dymore tended to predict a slightly lower damping ratio as velocity increased for all three dynamic modes presented. Whirl flutter for the semi-span model was not present up to 500 knots for the latest design, well above the operating range of the X-57.

Hoover, Christian B.↗
NASA NTRS2017

Approach Considerations in Aircraft with High-Lift Propeller Systems

NASA's research into distributed electric propulsion (DEP) includes the design and development of the X-57 Maxwell aircraft. This aircraft has two distinct types of DEP: wingtip propellers and high-lift propellers. This paper focuses on the unique opportunities and challenges that the high-lift propellers--i.e., the small diameter propellers distributed upstream of the wing leading edge to augment lift at low speeds--bring to the aircraft performance in approach conditions. Recent changes to the regulations related to certifying small aircraft (14 CFR x23) and these new regulations' implications on the certification of aircraft with high-lift propellers are discussed. Recommendations about control systems for high-lift propeller systems are made, and performance estimates for the X-57 aircraft with high-lift propellers operating are presented.

Patterson, Michael D.↗
NASA NTRS2017

Trajectory Optimization of Electric Aircraft Subject to Subsystem Thermal Constraints

Electric aircraft pose a unique design challenge in that they lack a simple way to reject waste heat from the power train. While conventional aircraft reject most of their excess heat in the exhaust stream, for electric aircraft this is not an option. To examine the implications of this challenge on electric aircraft design and performance, we developed a model of the electric subsystems for the NASA X-57 electric testbed aircraft. We then coupled this model with a model of simple 2D aircraft dynamics and used a Legendre-Gauss-Lobatto collocation optimal control approach to find optimal trajectories for the aircraft with and without thermal constraints. The results show that the X-57 heat rejection systems are well designed for maximum-range and maximum-efficiency flight, without the need to deviate from an optimal trajectory. Stressing the thermal constraints by reducing the cooling capacity or requiring faster flight has a minimal impact on performance, as the trajectory optimization technique is able to find flight paths which honor the thermal constraints with relatively minor deviations from the nominal optimal trajectory.

electric propulsion↗
NASA NTRS2018

Optimization of an Air Core Dual Halbach Array Axial Flux Rim Drive for Electric Aircraft

The anticipated development of the on-demand-mobility (ODM) market has accelerated the development of electric aircraft. Most proposed electric aircraft have propulsion systems that consist of fans directly driven by electric motors. The lower complexity of these propulsion systems opens the door to more custom propulsion system designs that are tailored to a given aircraft and its mission. This paper represents initial steps in the development of an electric propulsion system design code. A proof of concept version of the code is presented. The proof of concept version of the code is for the design of an axial flux rim driven propulsion system. NASA's all electric aircraft X-57, is used as a case study for this design code. The results of this case study are used to discuss the feasibility and potential benefits of using an axial flux rim driven propulsor on X-57. The final result of the case study shows a potential 4km increase in range over the current design.

Tallerico,Thomas F.↗
NASA NTRS2017

A NASA Approach to Safety Considerations for Electric Propulsion Aircraft Testbeds

Electric, hybrid-electric, and turbo-electric distributed propulsion technologies and concepts are beginning to gain traction in the aircraft design community, as they can provide improvements in operating costs, noise, fuel consumption, and emissions compared to conventional internal combustion or Brayton-cycle powered vehicles. NASA is building multiple demonstrators and testbeds to buy down airworthiness and flight safety risks for these new technologies, including X-57 Maxwell, HEIST, Airvolt, and NEAT.

electric propulsion↗
NASA NTRS2018

An Overview of the Layered and Extensible Aircraft Performance System (LEAPS) Development

The Layered and Extensible Aircraft Performance System (LEAPS) is a new sizing and synthesis tool being developed within the Aeronautics Systems Analysis Branch (ASAB) at NASA Langley Research Center. It is a modular, multidisciplinary, multi- fidelity sizing and synthesis tool for modeling advanced aircraft concepts and architectures such as electric/hybrid-electric propulsion, unconventional propulsion airframe integration, and non-traditional mission trajectories. The development of LEAPS is motivated by the lack of existing tools that meet the needs of ASAB. The Flight Optimization System (FLOPS) has been the primary sizing and synthesis tool of ASAB for three decades. However, FLOPS has a number of limitations that make it dicult to use for unconventional aircraft designs. Three high-level goals have been adopted to guide the LEAPS development pro- cess. LEAPS is being developed in Python with an architecture built to enable a exible and extensible analysis capability using the concept of an aircraft object that combines data and analysis models. Five challenge problems for LEAPS have been identi ed to measure progress: analysis of a conventional tube-and-wing aircraft using legacy methods, coupled aeroelastic analysis for weight estimation of a conventional tube-and-wing aircraft, analysis of an advanced hybrid-electric concept, analysis of the X-57 Maxwell distributed electric propulsion aircraft, and optimization of the trajectory of a supersonic vehicle to minimize sonic boom. LEAPS will be a publicly available capability of exceptional quality with modularity and extensibility that makes it a robust tool for design and analysis of current and future unconventional aircraft concepts.

Welstead, Jason R.↗
NASA NTRS2018

Design and Performance of a Hybrid-Electric Fuel Cell Flight Demonstration Concept

As electric powertrain and propulsion-airframe integration technologies advance, airborne electric propulsion concepts appear to be on the cusp of disrupting or transforming aviation markets. One of the many challenges to this transformation lies within the onboard energy storage and generation technologies. State-of-the-art battery technology is heavy and lacks support infrastructure; purely combustion-based solutions to electrical power generation suffer from increased inefficiency as compared to a traditional combustion powertrain. This paper explores another alternative: a hybrid-electric, solid oxide fuel cell power system. This power system reforms traditional fuels to feed fuel cells that generate electrical power for the aircraft electric powertrain. A representative power system is designed based on the requirements for NASA’s X-57 Mod II electric flight demonstrator platform, and is shown to exceed system feasibility goals of 300 W/kg and 60% efficiency in at least one configuration. The hybrid-electric fuel cell power system is shown to be competitive with the range performance of a combustion-based power architecture and comparable in mission energy cost to a battery-electric power system.

Borer, Nicholas K.↗