SEARCH · Search NASA
Results for “YARN”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Knittable and Washable Multifunctional MXene-Coated Cellulose Yarns
Textile-based electronics enable the next generation of wearable devices, which have the potential to transform the architecture of consumer electronics. Highly conductive yarns that can be manufactured using industrial-scale processing and be washed like everyday yarns are needed to fulfill the promise and rapid growth of the smart textile industry. By coating cellulose yarns with Ti 3 C 2 T x MXene, highly conductive and electroactive yarns are produced, which can be knitted into textiles using an industrial knitting machine. It is shown that yarns with MXene loading of ≈77 wt% (≈2.2 mg cm -1 ) have conductivity of up to 440 S cm -1 . After washing for 45 cycles at temperatures ranging from 30 to 80 °C, MXene-coated cotton yarns exhibit a minimal increase in resistance while maintaining constant MXene loading. The MXene-coated cotton yarn electrode offers a specific capacitance of 759.5 mF cm -1 at 2 mV s -1 . Additionally, a fully knitted textile-based capacitive pressure sensor is also prepared, which offers high sensitivity (gauge factor of ≈6.02), wide sensing range of up to ≈20% compression, and excellent cycling stability (2000 cycles at ≈14% compression strain). This work provides new and practical insights toward the development of platform technology that can integrate MXene in cellulose-based yarns for textile-based devices.
Effect of solvent/polymer infiltration and irradiation on microstructure and tensile properties of carbon nanotube yarns
Recently carbon nanotube (CNT) yarns have been gaining importance as an approach to harvest the excellent properties of the CNTs. However, the properties of CNT yarns at this stage are well below the expected value. Investigation of the structure of CNT yarns and possible approaches to enhance the strength and modulus are reported. Scanning electron microscopy and focused ion beam imaging reveal the inherently porous structure and poor orientation, emphasizing the need to enhance packing of CNT bundles in the yarns for increased strength and modulus. Densification of CNT yarn by toluene or polystyrene increases the strength by 140 or 172 % and modulus by 79 or 218 %, respectively, as compared to that of the pristine yarn. E-beam irradiation was investigated as a means to introduce crosslinking and enhanced internanotubes bonding to increase strength and modulus. However, the irradiation resulted in generation of defects and damages to the yarn contributing to reduction in strength and modulus. Raman spectroscopy studies on the irradiated samples reveal the change in bonding characteristics resulting in poor mechanical properties. As a result, denser packing of nanotubes and increased interaction without any damage is the key to improve the properties of CNT yarns.
High-Resolution X-ray Spectromicroscopy Reveals Process-Structure Correlations in sub-5-μm Diameter Carbon Nanotube-Polymer Composite Dry-Spun Yarns
A persistent lack of detailed and quantitative structural analysis of these hierarchical carbon nanotube (CNT) ensembles precludes establishing processing-structure-property relationships that are essential to enhance macroscale performance (e.g., in mechanical, electrical, thermal applications). Here, in this work, we use scanning transmission X-ray microscopy (STXM) to analyze the hierarchical, twisted morphology of dry-spun CNT yarns and their composites, quantifying key structural characteristics such as density, porosity, alignment, and polymer loading. As the yarn twist density increases (15,000 to 150,000 turns per meter), the yarn diameter decreased (4.4–1.4 μm) and density increased (0.55–1.26 g·cm –3 ), as intuitively expected. Yarn density, ρ, ubiquitously scaled with diameter d according to ρ ~ d –2 for all parameters studied here. Spectromicroscopy probes with 30 nm resolution and elemental specificity were employed to analyze the radial and longitudinal distribution of the oxygen-containing polymer content (~30% weight fraction), demonstrating nearly perfect filling of the voids between CNTs with a vapor-phase polymer coating and cross-linking process. These quantitative correlations highlight the intimate connections between processing conditions and yarn structure with important implications for translating the nanoscale properties of CNTs to the macroscale.
Multiscale Mechanisms of Twisted Carbon Nanotube Yarns Probed In Situ by Soft X-rays during Tensile Loading
Piecing together carbon nanotubes (CNTs) into assemblies has so far failed to achieve the same elite strength performance metrics as individual CNTs, highlighting a critical deficiency in understanding the effects that the processing of individual nanostructures have on the performance of their derived macroscale assemblies, thereby hindering the development of a process-structure-performance map for these materials. Here, in this work, we propose a method to decouple the distribution orientation of nanoscale tortuosity and the microscale twist of CNT dry-spun yarns under applied loads via in situ soft X-ray probing at high energy (1200 eV) and low energy (280 eV), respectively. With this decoupling enabled by in situ soft X-ray scattering, we acquired a deeper understanding of the deformation mechanisms of these yarns. We found that for untreated yarns, the twist angle of collective CNT bundles at the macroscale is more sensitive to applied stress than the nanoscale alignment distribution. We also found that increasing nominal twist densities of yarns as well as increased strengthening via plasma treatments and polymer infiltration act to decrease the yarns’ sensitivity to realignment at the nanoscale and prevent failure by the slip mechanism.
YARNsim: Simulating Hadoop YARN
Despite the popularity of the Apache Hadoop system, its success has been limited by issues such as single points of failure, centralized job/task management, and lack of support for programming models other than MapReduce. The next generation of Hadoop, Apache Hadoop YARN, is designed to address these issues. In this paper, we propose YARNsim, a simulation system for Hadoop YARN. YARNsim is based on parallel discrete event simulation and provides protocol-level accuracy in simulating key components of YARN. YARNsim provides a virtual platform on which system architects can evaluate the design and implementation of Hadoop YARN systems. Also, application developers can tune job performance and understand the tradeoffs between different configurations, and Hadoop YARN system vendors can evaluate system efficiency under limited budgets. To demonstrate the validity of YARNsim, we use it to model two real systems and compare the experimental results from YARNsim and the real systems. The experiments include standard Hadoop benchmarks, synthetic workloads, and a bioinformatics application. The results show that the error rate is within 10% for the majority of test cases. The experiments prove that YARNsim can provide what-if analysis for system designers in a timely manner and at minimal cost compared with testing and evaluating on a real system.
Single-step process to improve the mechanical properties of carbon nanotube yarn
Carbon nanotube (CNT) yarns exhibit low tensile strength compared to conventional high-performance carbon fibers due to the facile sliding of CNTs past one another. Electron beam (e-beam) irradiation was employed for in a single-step surface modification of CNTs to improve the mechanical properties of this material. To this end, CNT yarns were simultaneously functionalized and crosslinked using acrylic acid (AA) and acrylonitrile (AN) in an e-beam irradiation process. The chemical modification of CNT yarns was confirmed by X-ray photoelectron spectroscopy (XPS), Raman spectroscopy and scanning electron microscopy (SEM). The best improvement in mechanical properties was achieved on a sample treated with an aqueous solution of AA and subsequent irradiation. CNT yarn treatment with AA enhanced the strength (444.5 ± 68.4 MPa) by more than 75% and the modulus (21.5 ± 0.6 GPa) by more than 144% as compared to untreated CNT yarn (strength 251 ± 26.5 MPa and modulus 8.8 ± 1.2 GPa).
Biocatalytic Yarn for Peroxide Decomposition with Controlled Liquid Transport
In this study, a robust biocatalytic yarn with controllable liquid transport properties is created by coating thin layers of chitosan containing catalase onto a cellulosic yarn. The resulting material integrates enzyme catalytic functionality with protective coating properties of chitosan and structural functionality of the textile. Mild immobilization conditions and good affinity between the two polysaccharides minimize enzyme inactivation during the preparation steps and prevent enzyme from leaching during peroxide decomposition testing and washing, providing a novel and versatile enzyme immobilization strategy. The catalytic efficiency of enzymes in a reaction containing solid, liquid, and gas phases is facilitated when dissolved enzyme substrate is transported by liquid flowing through the coated textile structure. The flow-through configuration decomposes at least two times more peroxide in a twenty-times smaller reaction zone volume compared to a stirred tank configuration. Liquid transport through the yarn and liquid spatial distribution within the yarn are investigated by in situ neutron radiography and neutron computed tomography, revealing a constrained wicking mechanism that benefits biocatalytic yarn performance. This new class of sustainable and flexible biocatalytic textile matrices has beneficial multifunctional properties, not previously described, that are applicable for numerous small- and large-scale applications including controlled flow reactors and reactive filtration.
Liquid-free covalent reinforcement of carbon nanotube dry-spun yarns and free-standing sheets
Carbon nanotubes (CNTs) possess exceptional mechanical properties, surpassing stiffness and strength metrics of common materials such as steel alloys by 100× at the nanoscale. However, when myriads of individual CNTs are bundled together into macroscopic ensembles like fibers or sheets, the result is a 100-fold drop in strength compared to its individual components. Here we present a general strategy aimed to close this gap in property scaling. By using vapor-phase polymerization of a crosslinkable polymer, we reinforced the weak interlinkages among individual CNTs within both yarns and sheets to promote a better transference of mechanical load across the structure. Furthermore, after the treatment, dry-spun, low-density 2.3 μm thin yarns increased their elastic moduli by at least 300%, and free-standing CNT sheets exhibited a 10× boost. In-situ synchrotron small-angle X-ray scattering revealed that polymer-reinforced yarns undergo limited CNT bundle rearrangement when subjected to tensile loads compared to pristine yarns. This evidence supports the hypothesis that the polymer hinders CNTs slippage, the root cause of the poor scaling of mechanical properties in these materials. While we demonstrated this reinforcement method for CNT structures, it is not specific to CNTs and could be used in a wide variety of other hierarchical nanostructured ensembles.
Fabrication and Characterization of Aligned YBa{sub 2}Cu{sub 3}O{sub 7 − δ} Superconductor Electrospun Nanofibers and Twisted Yarn Based on PVA
YBa{sub 2}Cu{sub 3}O{sub 7 − δ} (YBCO) superconducting twisted yarns from electrospun aligned nanofibers are produced with a critical transition temperature of T{sub c} = 92 K. A solution of PVA and Y–Ba–Cu acetates are used as a precursor in the electrospinning to prepare aligned nanofibers and twisted yarns. The aligned nanofibers and twisted yarns are then pyrolysed to remove PVA and sintered to obtain a superconducting phase. Finally, before and after sintering, the aligned nanofibers and twisted yarns are studied by SEM, XRD, and AC magnetic susceptibility techniques. Results are presented in this paper.
Effect of twist on transverse impact response of ballistic fiber yarns
A Hopkinson bar was employed to conduct transverse impact testing of twisted Kevlar KM2 fiber yarns at the same impact speed. The speed of Euler transverse wave generated by the impact was measured utilizing a high speed digital camera. The study included fiber yarns twisted by different amounts. The Euler transverse wave speed was observed to increase with increasing amount of twist of the fiber yarn, within the range of this investigation. As a result, the higher transverse wave speeds in the more twisted fiber yarns indicate better ballistic performance in soft body armors for personal protection.
Nonlinear Deformation Behavior of New Braided Composites with Six-axis Yarn Orientations
The braiding technology is one of fabrication methods that can produce three-dimensional fiber preforms. Braided composites have many advantages over other two-dimensional composites such as no delamination, high impact and fatigue properties, near-net shape preform, etc. Due to the undulated yarns in the braided preforms, however, their axial stiffness is lower than that of uni-directional or woven composites. To improve the axial stiffness, the longitudinal axial yarns were already introduced along with the braiding axis (five-axis braiding technology). In this study, we developed a new braided structure using six-axis braiding technology. In addition to braiding and longitudinal axial yarns, transverse axial yarn was introduced. New braided composites, so called six-axis braiding composites, were manufactured using ultra high molecular weight polyethylene and epoxy resin and their mechanical properties were characterized. To investigate the mechanical performance of these braided composites according to their manufacturing conditions, a numerical analysis was performed using their unit-cell modeling and finite element analysis. In the analysis the nonlinear deformation behavior will be included.
Dwindling the resistance value of PEDOT:PSS – coated on fabric yarns
Herein we describe by dip coating method to transform typical fabric yarn to conductive fiber. Different types of yarns have been used to coat from a known conductive polymer, Poly (3,4ethylenedioxythiophene) Poly (styrene sulfonic acid). We have optimized the method to have lesser resistance of the conductive yarns. The minimum resistance achieved has a value of 77 Ω/cm. This value is not high as metals but could be comparable to that of metal oxides or semiconducting materials. However, flexibility of yarns and feeling of fabric combining with the conductivity developed in this process is suitable for wearable electronics and also as gas sensors, electromagnetic shielding.
More Powerful Twistron Carbon Nanotube Yarn Mechanical Energy Harvesters
We report that stretching a coiled carbon nanotube (CNT) yarn can provide large, reversible electrochemical capacitance changes, which convert mechanical energy to electricity. Here, it is shown that the performance of these “twistron” harvesters can be increased by optimizing the alignment of precursor CNT forests, plastically stretching the precursor twisted yarn, applying much higher tensile loads during precoiling twist than for coiling, using electrothermal pulse annealing under tension, and incorporating reduced graphene oxide nanoplates. The peak output power for a 1 and a 30 Hz sinusoidal deformation are 0.73 and 3.19 kW kg -1 , respectively, which are 24- and 13-fold that of previous twistron harvesters at these respective frequencies. This performance at 30 Hz is over 12-fold that of other prior-art mechanical energy harvesters for frequencies between 0.1 and 600 Hz. The maximum energy conversion efficiency is 7.2-fold that for previous twistrons. Twistron anode and cathode yarn arrays are stretched 180° out-of-phase by locating them in the negative and positive compressibility directions of hinged wine-rack frames, thereby doubling the output voltage and reducing the input mechanical energy.
Tensile strength of ramie yarn (spinning by machine)/HDPE thermoplastic matrix composites
Technological developments should be trooped to prevent a gap between technology and environmental sustainability, then it needs to be developed “Green technology”. In this research is making of green composites which use natural fiber ramie as reinforcement. Whereas the matrix used was HDPE (High Density Polyethylene) thermoplastic polymer which could be recycled and had a good formability and flexibility. The ramie yarns and fibers for unidirectional (0°) direction respectively were mixed with HDPE powder and processed using hot compression molding. The surface morphology was observed by SEM (Scanning Electrone Microscopy). Results showed that both tensile strength of the ramie fiber/HDPE composites increased in comparison with the ramie yarn (spinning by machine)/HDPE composites. However, the ramie yarn (spinning by machine)/HDPE composites have a good producibility for wider application. Analysis of the test results using the Weibull distribution as approaches to modeling the reliability of the specimens.
Grafting polymer coatings onto the surfaces of carbon nanotube forests and yarns via a photon irradiation process
Surface activation of carbon nanotubes (CNTs) as forests and yarns, depolytmerization of candidate polymers, and uniform deposition and re-polymerization onto the activated CNTs are simultaneously achieved by exposing CNTs and polymer targets to light with a narrow wavelength distribution from a vacuum ultraviolet lamp. Both polystyrene and poly (methyl methacrylate) are deposited onto the surface of CNTs in the CNT-forest and yarn in a N{sub 2} environment for 30 min during which the polymer uniformly coats the carbon nanotubes. X-ray photoelectron spectroscopy data reveal that covalent bonding occurs at the CNT-polymer interface.
Thermal conductivity of high performance carbon nanotube yarn-like fibers
In the present paper, we present results of thermal conductivity measurements in free standing carbon nanotube (CNT) yarn-like fibers. The measurements are made using a T-type experimental configuration utilizing a Wollaston-wire hot probe inside a scanning electron microscope. In this technique, a suspended platinum wire is used both as a heater and a thermal sensor. A low frequency alternating current source is used to heat the probe wire while the third harmonic voltage across the wire is measured by a lock-in amplifier. The conductivity is deduced from an analytical model that relates the drop in the spatially averaged temperature of the wire to that of the sample. The average thermal conductivity of the neat CNT fibers and the CNT –polymer composite fibers is found to be 448 W/m-K and 225 W/m-K, respectively. These values for conductivity are amongst the highest measured for CNT yarn-like fibers fabricated using a dry spinning process from vertically aligned CNT arrays. The enhancement in thermal conductivity is understood to be due to an increase in the CNT fiber elastic stiffness during the draw and twist operations, lower CNT thermal contact resistance due to increase in CNT contact area, and better alignment of the CNT fibrils along the length of the fiber.
Different Electrochemical Behavior of Cationic Dopamine from Anionic Ascorbic Acid and DOPAC at CNT Yarn Microelectrodes
Carbon nanotube yarn microelectrodes (CNTYMEs) have micron-scale surface crevices that momentarily trap molecules. CNTYMEs improve selectivity among cationic catecholamines because secondary reactions are enhanced, but no anions have been studied. Here, we compared fast-scan cyclic voltammetry (FSCV) of dopamine and anionic interferents 3,4 dihydroxyphenylacetic acid (DOPAC) and L-ascorbic acid (AA) at CNTYMEs and carbon fiber microelectrodes (CFMEs). At CFMEs, dopamine current decreases with increasing FSCV repetition frequency at pH 7.4, whereas DOPAC and AA have increasing currents with increasing frequency, because of less repulsion at the negative holding potential. Both DOPAC and AA have side reactions after being oxidized, which are enhanced by trapping. At pH 4, the current increases for DOPAC and AA because they are not repelled. In addition, AA has a different oxidation pathway at pH 4, and an extra peak in the CV is enhanced by trapping effects at CNTYMEs. At pH 8.5, co-detection of dopamine in the presence of DOPAC and AA is enhanced at 100 Hz frequency because of differences in secondary peaks. Thus, the trapping effects at CNTYMEs affects anions differently than cations and secondary peaks can be used to identify dopamine in mixture of AA and DOPAC with FSCV.