Search NASA⌕ Search

SEARCH · Search NASA

Results for “Zirconium cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Report summarizing demonstration of thermal conductivity measurement methods for coated zirconium cladding

Thermal diffusivity measurements on Zirconium-based cladding materials have historically been a challenge due to the difficulty to measure on specimens with curved geometries, including nuclear grade Zircaloy cladding materials. In this work, we first used Laser Flash Analysis methods to measure the thermal diffusivity of Zircaloy tubes, which show good agreement with Zircaloy plates in this work, as well as previously published data. The consistent results proved the applicability of the Laser Flash Analysis setup for investigating thermal diffusivity of Zircaloy tubes. We further investigate the hydrogen effect on thermal diffusivity of Zircaloy tubes. Hydrogen plays significant roles in temperature dependent thermal diffusivity trends of Zircaloy tube. For low hydrogen concentration, where hydride dissolved into single phase α-Zr at higher temperature, thermal diffusivity is relatively unchanged at low temperature at two phase regions (α-Zr and δ-hydride), and it increases as a function of temperature at single phase α-Zr region. For high hydrogen concentration, where phase transformation (α-Zr + δ-hydride → α-Zr + β-Zr) occurs at 567 °C, thermal diffusivity decreases as a function of temperature below 567 °C before the transformation (α-Zr and δ-hydride), while increase at higher temperature after the transformation (α-Zr and β-Zr).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Impact of Coating Defects on Performance of Coated Zirconium Cladding

Research on accident tolerant fuels (ATF) has started after the Fukushima accident [1–3]. While efforts have been expended on both fuel and cladding ATF concepts, the bulk of work has been devoted to improved cladding. The overarching goal of these approaches is to extend the coping time available during a severe accident before any event would result in release of radioactivity to the public. The most basic ATF cladding concept is obtained by applying a thin coating of highly corrosion-resistant material on the surface of a licensed zirconium cladding alloy. This thin coating is intended to not interfere with the neutronic or mechanical performance of the base cladding under normal operating conditions. Different coating materials, thicknesses, coating processes, process parameters, and testing methods have an impact on the microstructure and mechanical properties and therefore on the results of the applied investigation methods. These challenges have motivated an initial focus on demonstrating that the presence of coatings do not perturb the critical performance benchmarks of uncoated material. Ongoing lead test assembly irradiations of coated zirconium concepts in commercial reactions is intended to establish baseline performance in this regard in the coming years.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deposition of integrated protective material into zirconium cladding for nuclear reactors by high-velocity thermal application

A zirconium alloy nuclear reactor cylindrical cladding has an inner Zr substrate surface, an outer volume of protective material, and an integrated middle volume of zirconium oxide, zirconium and protective material, where the protective material is applied by impaction at a velocity greater than 340 meters/second to provide the integrated middle volume resulting in structural integrity for the cladding.

Mazzoccoli, Jason P.↗
NASA NTRS1973

Theoretical analysis of swelling characteristics of cylindrical uranium dioxide fuel pins with a niobium - 1-percent-zirconium clad

The relations between clad creep strain and fuel volume swelling are shown for cylindrical UO2 fuel pins with a Nb-1Zr clad. These relations were obtained by using the computer code CYGRO-2. These clad-strain - fuel-volume-swelling relations may be used with any fuel-volume-swelling model, provided the fuel volume swelling is isotropic and independent of the clad restraints. The effects of clad temperature (over a range from 118 to 1642 K (2010 to 2960 R)), pin diameter, clad thickness and central hole size in the fuel have been investigated. In all calculations the irradiation time was 500 hours. The burnup rate was varied.

Saltsman, J. F.↗
DOE OSTI2023

A novel protocol to recycle zirconium from zirconium alloy cladding from used nuclear fuel rods

A potential new zirconium recycling protocol has been demonstrated using unirradiated Zircaloy-based claddings and depleted uranium oxide for the chemical removal of zirconium alloy cladding in used nuclear fuel (UNF) rods from light water reactors. This protocol is based on the application of three new scientific findings. First, a new lower temperature chlorination reaction of zirconium with sulfur monochloride is described. Second, the high solubility of zirconium chloride in thionyl chloride is used to separate it from uranium oxide fuel and fission and activation contaminants. Finally, in the third step, the zirconium chloride is purified by simple recrystallization from thionyl chloride. Utilizing sulfur chloride solvents for a lower temperature liquid-based chemical digestion and purification of zirconium alloy claddings reduces technical complications experienced by current high temperature gas phase chlorination strategies, such as contamination of product streams. This novel protocol has been demonstrated on a 3–50 g scale of unirradiated zirconium alloy, with no significant change in the time required for complete chlorination (3–4 h). This zirconium chlorination protocol has also been performed in the presence of depleted uranium oxide pellets. The depleted fuel pellets do not affect zirconium chlorination, and the chlorination protocol does not chemically or physically alter the fuel pellets. Finally, a preliminary description of an industrial protocol to recycle nuclear grade zirconium from UNF rods is presented.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Produce ZrH Moderator Material

This reports complete Milestone M2.2.3 Produce zirconium hydride moderator material. In this milestone, we report the successful fabrication of FeCrAl alloys cladded zirconium hydride moderator. Different types of crucible designs were presented, including the basic design with bar cladding material, basic design with tube cladding material, and crucible design with position holding function. Mo and FeCrAl were used as the trial cladding materials. The welding techniques and procedures were reported and discussed. Totally three welding techniques were adopted in the development of moderator cladding, and they are electron beam welding (EBW), laser welding (LW), and gas tungsten arc welding (GTAW). After welding, all cladded crucibles were evaluated with two kinds of leak testing, the helium leak test for minor leakage and the bubble test for major leakage. Due to the concern of the poor neutronics performance, Mo was not ideal for future moderator cladding application. Therefore, detailed characterization of the Mo cladded zirconium hydride was not pursued. Instead, the characterization of FeCrAl cladded zirconium hydride was performed. We discussed two material conditions (i.e., as machined and pre-oxidized conditions) prior to the cladding process, evaluated thermal stability of cladded zirconium hydride moderator through directly measuring hydrogen release, and characterized the zirconium hydride following the thermal desorption measurement. The results showed pre-oxidized FeCrAl is capable of efficiently preventing hydrogen release from the moderator assembly.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Investigation of Degradation Mechanisms of Cr-coated Zirconium Alloy Cladding in Reactivity-Initiated Accident

Reactivity-initiated accident testing has been performed on two baseline fuel rodlets which were fabricated from Zr-4 cladding and utilized fresh UO 2 fuel pellets. These experiments are part of a larger series of transient irradiations to explore Cr-coated zirconium alloy cladding under Reactivity-initiated accident conditions to evaluate ballooning and burst and sever oxidation characteristic of late-stage failure. The first two irradiations have been completed and post-transient examinations have been performed. In one rod, ballooning and burst occurred, along with oxidation. The second rod leaked and as a result did not balloon as much during the transient. This second rod also experienced increased oxidation compared to the first due to higher temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Sensitivity analysis for characterizing the impact of HNGD model on the prediction of hydrogen redistribution in Zircaloy cladding using BISON code

Hydrogen in zirconium cladding is able to precipitate into zirconium hydrides which impacts cladding integrity. The Hydride Nucleation-Growth-Dissolution (HNGD) model in the BISON code accounts for the precipitation and dissolution kinetics of hydride in Zircaloy material. This paper presents global sensitivity analyses of the HNGD model aiming to enhance our understanding of the hydride precipitation phenomena by quantifying the variance that key parameters have on the prediction of hydrogen behavior under various environmental conditions. Here, model predictions are compared to experimental data obtained under two different conditions: 1) with uniformly precharged specimens subjected to a linear thermal gradient, and 2) specimens precharged with a cathodically applied hydride rim at one end of the sample and subjected to an asymmetric thermal gradient. The Sobol sensitivity analysis identifies the key parameters in the HNGD model for both types of specimens. For linear temperature cases, the heat of transport dominates the accuracy of predictions when no precipitation occurs at the cold end, while Terminal Solid Solubility for Dissolution (TSSD) is the most important parameter when precipitation occurs. A large variation in the predicted hydrogen concentration profiles is found in the range of high TSSD due to the occurrence of precipitation. For asymmetric temperature cases, the solubility coefficient gives the largest impact on the predicted hydrogen distribution, as it determines the amount of solute hydrogen dissolved from the initially applied hydride rim. A large discrepancy in hydrogen distribution between simulations and experiments exists with the asymmetric specimens because BISON simulations fail to predict the precipitation of hydride at the cooler end. Comparative studies using former and updated models verifies the significant impact of the hydride growth mechanism on predicted hydrogen concentration profiles. In particular, when hydride initially exists, changes in TSSD generate a large variation in the predicted amount of precipitation by hydride growth, giving large uncertainty in predicting the hydrogen distribution over the sample length. The outputs characterize the significant impact of the hydride growth mechanism in the HNGD model on predicting hydrogen behavior, and improve the understanding of the precipitation of hydride in Zircaloy cladding within a range of expected environmental conditions. The analyses indicate work is still needed to improve the hydride solvus models in the BISON code to accurately predict experimentally observed hydride concentrations and distributions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Bench-Scale Electrolytic Dissolution of Quarter-Scale FCA Cans

In 2016, the Savannah River National Laboratory (SRNL) led, in support of and under sponsorship of the Department of Energy’s National Nuclear Security Administration (DOE/NNSA) Office of Material Management and Minimization (M3), the removal and transfer of the plutonium based Fast Critical Assembly (FCA) fuel from the Japan Atomic Energy Agency (JAEA) Tokai facility to the Savannah River Site (SRS). The team also included JAEA, multiple organizations in Savannah River Nuclear Solutions (SRNS), International Nuclear Services, and many other entities. The FCA fuel removal project completion was a key deliverable for M3 to the 2016 Nuclear Security Summit and constituted the largest inventory of weapons-usable plutonium removed under the nonproliferation program. The FCA materials consist of thousands of stainless steel (SS) clad plates and hundreds of SS clad rods. The FCA fuel elements were packaged in a carrier can and stored at SRS pending disposition of the fuel. Following an assessment of candidate disposition options, SRNS identified electrolytic dissolution (ED) as the most promising disposition option for the FCA plates and their preferred option was endorsed by DOE. This option entails electrochemically dissolving the entire FCA carrier can with fuel elements and was based on bench-scale laboratory testing and historical work on processing SS-clad and zirconium-clad uranium-based fuel in the H-Canyon electrolytic dissolver (last operated in 1980). The FCA plate consists of a plutonium-aluminum metal alloy core hermitically sealed in SS cladding.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Dynamic Probabilistic Risk Assessment Based Response Surface Approach for FLEX and Accident Tolerant Fuels for Medium Break LOCA Spectrum

After the Fukushima Daiichi Accident, the safety features such as accident tolerant fuel (ATF) and diverse and flexible coping strategies (FLEX) for existing nuclear fleets are being investigated by the US Department of Energy under the Light Water Reactor Sustainability Program. This research is being conducted to quantify the risk-benefit of these safety features. Dynamic probabilistic risk assessment (DPRA)-based response-surface approach has been presented to quantify the FLEX and ATF benefits by estimating the risk associated with each option. ATFs with multilayered silicon carbide (SiC), iron-chromium-aluminum, and chromium-coated zirconium cladding were considered in this study. While these ATF candidates perform better than the current zirconium cladding (Zr), they may introduce additional failure modes in some operating conditions. The fuel failure analysis modules (FAMs) were developed to investigate ATF performance. The dynamic risk assessments were performed using RAVEN, a DPRA tool, coupled with RELAP5 and FAMs. A cumulative distribution function-based index provided a mean of comparing the benefits of safety enhancements. For medium break loss of coolant accidents, FLEX operational timing window for each fuel type was estimated. Among these ATF candidates, SiC-type ATF was the most beneficial candidate for an increased safety margin than Zr-based fuel and was found to complement FLEX strategies in terms of risk and coping time.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Silicon carbide reinforced zirconium based cladding

A method for making an improved nuclear fuel cladding tube includes reinforcing a Zr alloy tube by first winding or braiding ceramic yarn directly around the tube to form a ceramic covering, then physically bonding the ceramic covering to the tube by applying a first coating selected from the group consisting of Nb, Nb alloy, Nb oxide, Cr, Cr oxide, Cr alloy, or combinations thereof, by one of a thermal deposition process or a physical deposition process to provide structural support member for the Zr tube, and optionally applying a second coating and optionally applying a third coating by one of a thermal deposition process or a physical deposition process. If the tube softens at 800° C.-1000° C., the structural support tube will reinforce the Zr alloy tube against ballooning and bursting, thereby preventing the release of fission products to the reactor coolant.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Thermal Calculations to Determine Maximum Zircaloy Temperatures During Reactor Operations for Campaign 1 Fuel Assemblies

The H-Canyon Facility plans on processing bundles from Non-Aluminum Spent Nuclear Fuel (NASNF) Risk Group 1 (UO 2 core fuels). Uranium-zirconium (UZr) alloys and zirconium clad UO 2 fuel containing UZr intermetallic compound have the potential to cause explosions during dissolution. UZr intermetallic typically only forms when uranium and zirconium (or zirconium alloy) cladding are in contact at high temperatures. Thermal modeling was performed to determine the maximum cladding temperature for Campaign 1 Zircoloy cladded fuel assembles during reactor operation to help determine if the UZr intermetallic compound could have formed during reactor operations. The temperature of 350°C was chosen as a conservative minimum value for the possible formation of intermetallic UZr compound. The modeling approach, inputs, and results are outlined in this document.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Downselection of Cladding Materials for Zirconium Hydride Moderator

This report complete Milestone M3.1.1 — “Cladding downselection: Team will report to ARPA-E on at least two down-selected cladding options—one metallic and one ceramic.” In this milestone, we systematically assess FeCrAl alloys and SiC-based cladding options for a zirconium hydride (ZrHx) moderator in terms of their neutronics, radiation stability, hydrogen permeability, chemical compatibility, and fabricability. The analysis shows that FeCrAl alloys are excellent candidate cladding materials for a ZrHx moderator given their proven radiation stability, acceptable compatibility with ZrHx, and industrially established fabricability. The relative high hydrogen permeability is manageable by introducing a thin layer of an Al 2 O 3 hydrogen permeation barrier on the external surface. The SiC-cladded ZrHx moderator is promising because of its outstanding neutronics performance, excellent radiation stability, and extremely low intrinsic hydrogen permeability. However, potential interactions of SiC and Zr and the challenge in achieving a hermetic SiC-based cladding require further investigation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Post-Irradiation Fracture Toughness Characterization of Generation II FeCrAl Alloys

Currently, the handbook on FeCrAl material properties contains only limited data regarding the fracture toughness properties of any FeCrAl alloy, let alone alloys currently under investigation within the Advanced Fuels Campaign (AFC) such as the Oak Ridge National Laboratory (ORNL) derived FeCrAl alloys. Unirradiated datasets developed both by ORNL and previously within literature using Charpy V-notch specimens to determine the ductile to brittle transition temperature (DBTT) showed key findings including (i) increasing Al and/or Cr content can raise the DBTT of FeCrAl alloys, (ii) DBTT values can typically reside at or above room temperature for FeCrAl alloys, and (iii) grain size and residual strain can have an effect on the fracture properties. These results suggest that the fracture toughness of FeCrAl alloys may be a factor in its deployment for nuclear power applications, but no studies have been completed prior regarding the DBTT or fracture toughness of FeCrAl alloys after neutron irradiation, especially for the leaner Cr content alloys currently under investigation as candidate alloys for light water reactor (LWR) cladding. Taken in isolation, embrittlement of a cladding alloy during service has no bearing on possible licensure. Hydriding of zirconium cladding alloys is well understood to result in significant embrittlement. Furthermore, mechanical failure of irradiated cladding containing fuel pellets occurs at far higher stresses than defueled cladding samples because the presence of the fuel toughens the fuel rod. Despite this absence of direct relevance to licensure, radiation embrittlement is a fundamental structure-property evolution that should be understood to guide further development of FeCrAl alloys. Licensure of FeCrAl incorporates far more complex system behaviors that will not be possible until larger quantities of fueled irradiated rodlets are available.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗