Search NASA⌕ Search

SEARCH · Search NASA

Results for “activation volume”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Saddle point search with dynamic active volume

Sampling potential energy surface (PES) is critical for many problems in materials science, chemistry, physics, and biology and requires highly efficient saddle point searches (SPS). In the study, we introduce the concept of dynamic active volume (DAV) in addition to the active volume in self-evolving atomistic kinetic Monte Carlo (SEAKMC). The DAV method has further reduced the dimensionality of the PES at the elevation stage of a SPS. At the subsequent converging stage, the dynamic boundary in DAV is lifted to allow the system to converge to the right location of a saddle point. Coupled with the dimer method, the DAV method not only significantly reduces the time cost for a given search attempt, but also dramatically increases the probability of finding relevant saddle points for PES sampling. Further, a Python software package within the framework SEAKMC (SEAKMC_py) with the DAV method has been developed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Shear band velocity and activation volume during shear deformation by acoustic emission in a Zr-based bulk metallic glass

Here, an analysis is presented for the shear band velocity of plastic deformation and activation volume of the shear transformation zone (STZ) in a Zr 60 Cu 30 Al 10 bulk metallic glass (BMG). Compared to the values calculated by the stick-slip model, the values of shear band velocity calculated after optimization by the acoustic emission technique are much larger than those reported previously. Plastic flow in BMGs is found to be described by a power-law correlation between the maximum velocity of the shear band and the strain rates. Combining the free volume theory and the STZ theory, the relationship between the volume change in the STZ and the shear band velocity is derived as $Ω=A$(27–ln$v/l$). The value of A, which is a material dependent constant, is 5.43 × 10 –3 for the current BMG at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High-performance Generic Neutrino Detection in a LArTPC near the Earth's Surface with the MicroBooNE Detector

Large Liquid Argon Time Projection Chambers (LArTPCs) are being increasingly adopted in neutrino oscillation experiments because of their superb imaging capabilities through the combination of both tracking and calorimetry in a fully active volume. Active LArTPC neutrino detectors at or near the Earth's surface, such as the MicroBooNE experiment, present a unique analysis challenge because of the large flux of cosmic-ray muons and the slow drift of ionization electrons. We present a novel Wire-Cell-based high-performance generic neutrino-detection technique implemented in MicroBooNE. The cosmic-ray background is reduced by a factor of 1.4$\times10^{5}$ resulting in a 9.7% cosmic contamination in the selected neutrino candidate events, for visible energies greater than 200~MeV, while the neutrino signal efficiency is retained at 88.4% for $\nu_{\mu}$ charged-current interactions in the fiducial volume in the same energy region. This significantly improved performance compared to existing reconstruction algorithms, marks a major milestone toward reaching the scientific goals of LArTPC neutrino oscillation experiments operating near the Earth's surface.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Ion Size Effects on the Thermodynamic, Kinetic, and Mechanical Properties during Ion Exchange in Solid-State Electrolytes

Ion exchange offers a pathway to impose residual compressive stresses to mitigate the electro-chemo-mechanical cracking of solid-state electrolytes such as lithium lanthanum zirconium oxide. This study uses a coupled multiscale framework (integrating density functional theory (DFT), molecular dynamics (MD), and continuum modeling) to examine how exchange ion size influences stress, diffusion, fracture toughness, and electronic properties. Larger isovalent ions (Na + , Ag + , K + ) were exchanged with Li + , with DFT confirming their preference for octahedral 96h sites and a linear relationship between ion size and chemical free expansion coefficient. MD simulations reveal stress and concentration effects on exchange ion diffusivity at elevated temperatures, with Na + and Ag + maintaining favorable mobility while K + showing concentration-dependent clustering. Continuum modeling predicts the range of fracture strength improvements and the required ion exchange concentration profile. It was shown that a 5% surface exchange concentration can induce ∼0.6 GPa of surface compressive stress using Na + and ∼1.0 GPa of surface compressive stress using Ag + . On the other hand, larger ion exchange species may penalize Li + diffusivity by increasing the activation volume and activation energy. Interestingly, Na + has a negligible penalty on Li-ion diffusivity. The room temperature Li + ion diffusivity is reduced by ∼40% with Ag + ion exchange. Electronic band structure analysis shows no size-dependent change in the bandgap, though Ag + introduces localized defect states near the valence band maximum. This study highlights ion size as a key factor in optimizing LLZO properties, offering a framework to improve the solid-state battery performance.

Jagad, Harsh D. [Brown Univ., Providence, RI (Unit↗
DOE OSTI2022

Atomistic modeling of surface and grain boundary dislocation nucleation in FCC metals

Dislocation nucleation plays a critical role in the plastic deformation of crystalline materials. However, it is challenging to predict the active mode and associated rate of dislocation nucleation under typical experimental loading conditions through molecular dynamics simulation due to timescale limitations. In this report we use the free-end nudged elastic band method to determine the activation energies and activation volumes of dislocation nucleation in four typical face-centered cubic metals of Au, Al, Cu and Ni. We focus on the representative processes of surface and grain boundary dislocation nucleation. The atomistically determined activation volumes of these dislocation nucleation processes are larger than 10b3 (with b being the Burgers vector length) under typical experimental loading conditions. These results are compared with experimentally measured activation volumes in ultrafine-grained and nanocrystalline metals, thereby providing mechanistic insight into their rate-controlling deformation mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Atomic Gradient Structures: Atomic Gradient Structure Alters Electronic Structure in 3D across the Bulk and Enhances Photoactivity

Understanding structure–function relationships enables the design of materials with tailored functionalities. The long-standing challenge is to design materials with high active volume to improve the efficiency. Tailored grain boundaries and lattice defects are traditionally used to tune the electronic structure near interfaces or defects to promote electron and hole separation. However, the active volume of point defect sites or interfaces in these traditional photocatalysts is extremely low. In this work, we report a structure with continuous atomic positional deformation across the bulk, altering the electronic structure in three-dimension and creating a significantly high active volume. Such a structure in anatase is obtained and tuned by phase transformation during heating process. Transmission electron microscopy and density functional theory results reveal that atomic deformations result in continuous band bending across the particles, facilitating electron–hole separation, inhibiting their recombination, and inducing dramatically enhanced photoactivity. These findings enable a different materials design paradigm that can potentially be harnessed for a broad range of applications.

TiO2↗
DOE OSTI2021

Atomic Gradient Structure Alters Electronic Structure in 3D across the Bulk and Enhances Photoactivity

Abstract Understanding structure–function relationships enables the design of materials with tailored functionalities. The long‐standing challenge is to design materials with high active volume to improve efficiency. Tailored grain boundaries and lattice defects are traditionally used to tune the electronic structure near interfaces or defects to promote electron and hole separation. However, the active volume of point defect sites or interfaces in these traditional photocatalysts is extremely low. This study reports a structure with continuous atomic positional deformation across the bulk, altering the electronic structure in 3D and creating a significantly higher active volume. Such a structure in anatase is obtained and tuned by phase transformation during the heating process. Transmission electron microscopy and density functional theory results reveal that atomic deformations result in continuous band bending across the particles, facilitating electron–hole separation, inhibiting their recombination, and inducing dramatically enhanced photoactivity. These findings enable a different materials design paradigm that can potentially be harnessed for a broad range of applications.

Ren, Peng↗
DOE OSTI2023

Model for the Softening Factor within Stages of Work Hardening

A formulation for a dimensionless coefficient c b is derived that represents a scale of microstructural softening for alloys which follow Kocks-Mecking (K-M) work hardening behavior. The variation of the true plastic strain ε p between the proportional limit σ y and the strength σ u at the instability is determined using the Considère criterion. Parameterization of the model is limited to variables expressly measured within tensile experiments. Further development is now made for the softening factor c bi through the individual and sequential stages 3 and 4 of plastic deformation during K-M work hardening Q behavior. Application is shown for tensile test results of Ti-6Al-4V made by different additively manufactured (AM) processes. It is found that the variation in plastic strain as a function of c bi produces a continuous curve representative of the alloy system. The results of data analysis indicate that Θ o3 and c b3 increase, while Θ o4 and c b4 decrease, as the total plastic strain ε p increases. Furthermore, formulations derived for K-M stages 3 and 4 enable the evaluation of other material parameters such as the activation volume ν* for the onset of plastic deformation. This activation volume is found to be near constant, at a ν*-value of 0.353±0.036 nm 3 as computed using a strain-rate sensitivity of strength exponent m of 0.014, irrespective of the AM method used to produce the Ti-6Al-4V alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Role of Local Structure in the Enhanced Dynamics of Deformed Glasses

External stress can accelerate molecular mobility of amorphous solids by several orders of magnitude. The changes in mobility are commonly interpreted through the Eyring model, which invokes an empirical activation volume. Here, we analyze constant-stress molecular dynamics simulations and propose a structure-dependent Eyring model, connecting activation volume to a machine-learned field, softness. We show that stress has a heterogeneous effect on the mobility that depends on local structure through softness. The barrier impeding relaxation reduces more for well-packed particles, which explains the narrower distribution of relaxation time observed under stress.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2020

Plastic deformation of single crystals of the equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy in tension and compression from 10 K to 1273 K

In this report the plastic deformation behavior of single crystals of the quinary, equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy (HEA) with the face-centered cubic structure has been investigated in tension and compression as a function of crystal orientation and temperature from 10 K to 1373 K. The critical resolved shear stress (CRSS) for {111}<110> slip at room temperature is 42-45 MPa. It does not depend much on crystal orientation (i.e., the Schmid law holds true) and the sense (tension vs. compression) of the applied load. The CRSS for {111}<110> slip increases with the decrease in temperature, without showing any significant inertia effects at cryogenic temperatures below 77 K. Extrapolation from the measured yield stresses down to 10 K yields a CRSS value at 0 K of 168 MPa. At cryogenic temperatures, the measured strain-rate sensitivity of flow stress is consistent with a very small activation volume. The concept of stress equivalence holds true both for the temperature dependence of CRSS and the stress dependence of activation volume, indicating that solid-solution hardening is the major strengthening mechanism. Deformation twinning occurs at 77 K but not at room temperature, resulting in higher tensile elongation to failure at 77 K than at room temperature. Deformation twinning at 77 K occurs at a shear stress of 378 MPa on conjugate ($\bar1\bar11$) planes in the form of Lüders deformation after large plastic strain (about 85%) achieved by the stage I (easy glide) and stage II (linear work-hardening) deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Measurements of the ionization efficiency of protons in methane

The amount of energy released by a nuclear recoil ionizing the atoms of the active volume of detection appears “quenched” compared to an electron of the same kinetic energy. This different behavior in ionization between electrons and nuclei is described by the Ionization Quenching Factor (IQF) and it plays a crucial role in direct dark matter searches. For low kinetic energies (below 50 keV ), IQF measurements deviate significantly from common models used for theoretical predictions and simulations. We report measurements of the IQF for proton, an appropriate target for searches of Dark Matter candidates with a mass of approximately 1 GeV , with kinetic energies in between 2 keV and 13 keV in 100 mbar of methane. We used the Comimac facility in order to produce the motion of nuclei and electrons of controlled kinetic energy in the active volume, and a NEWS-G SPC to measure the deposited energy. The Comimac electrons are used as a reference to calibrate the detector with 7 energy points. A detailed study of systematic effects led to the final results well fitted by IQF (E K )=E$^α_K$ / (β+E$^α_K$) with α=0.70±0.08 and β=1.32±0.17 . In agreement with some previous works in other gas mixtures, we measured less ionization energy than predicted from SRIM simulations, the difference reaching 33% at 2 keV .

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2026

Creep in multi-principal element materials –– A review

The ongoing push towards enhanced energy efficiency and reduced emissions has necessitated the creation of materials with superior performance, especially under extreme conditions. Modern industries, such as aerospace, energy production, and nuclear power, rely heavily on materials that can withstand elevated temperatures without compromising structural integrity. At these heightened temperatures, materials, even when subjected to mechanical stresses well below their yield strength, may experience slow deformation leading to eventual rupture — a phenomenon known as creep. With the expansive design space that comes with the high entropy concept and their reported excellent high temperature strength, multi-principal element materials (MPEMs) have attracted interest in the scientific community for high-temperature applications. Here, this review offers a comprehensive examination of existing studies on creep in MPEMs, which includes multi-principal element−alloys, −bulk metallic glasses, −ceramics, and −superalloys, comparing published findings on MPEMs with pure elements, traditional alloys, bulk metallic glasses, and superalloys. The sub-topics covered include a comparison among different creep-testing methods, creep mechanisms, creep exponents, creep strain rates, activation volume, and creep-activation energy. Modeling efforts for predicting creep behavior of MPEMs are also reviewed. Methods for improving creep resistance by performing heat treatments and/or modifying microstructures are discussed. Overall, the current state of MPEMs has not yet surpassed the creep performance of commercial alloys. Finally, directions for future efforts are suggested, such as experimenting in various controlled environments, expanding the number of compositions tested, exploring advanced manufacturing techniques, and using machine-learning to predict creep properties based on compositions and microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Compact and efficient elastocaloric heat pumps—Is there a path forward?

Elastocaloric cooling holds promise for energy-efficient heat pumping near room temperature with low environmental impact. Its adoption is, however, impeded by disproportionally large sizes of actuators compared with the active material volume. Taking magnetocaloric cooling as the baseline, the value of no more than 10:1 actuator volume to active material volume should lead to both size- and cost-effective solutions that may potentially be competitive with vapor-compression devices. With the goal to establish performance metrics that can lead to informed actuator selection for specific regenerator requirements, we analyze a wide range of elastocaloric materials and actuator technologies to find the best matches. We find that actuation with magnetic shape memory alloys meets all requirements; however, this technology is currently in early developmental stages and such actuators are not widely commercially available. Another promising and easily accessible option is standard rotary electric motors in combination with rotary-to-linear transduction mechanisms. A theoretical analysis of two case studies of elastocaloric systems using rotary electric motors with a Scotch yoke mechanism demonstrates the usefulness of our approach. Actuator requirements are based on two different regenerator configurations: one starting from zero strain without any mechanical energy recovery and another with 2% pre-strain and mechanical energy recovery to reduce the power and torque required from the motor. Our results indicate that the 10:1 target actuator to active material volume ratio can be met and feasibly lowered further, demonstrating that the proposed method for selecting actuators makes compact and efficient elastocaloric systems possible.

42 ENGINEERING↗
DOE OSTI2024

Nuclear waste attributes of near-term deployable small modular reactors

The nuclear waste attributes of near-term deployable SMRs were assessed using established nuclear waste metrics, which are the DU mass, SNF mass, volume, activity, decay heat, radiotoxicity, and decommissioning LLW volumes. Metrics normalized per unit electricity generation were compared to a reference large PWR. Three SMRs, VOYGR, Natrium, and Xe-100, were selected because they represent a range of reactor and fuel technologies and are active designs deployable by the decade’s end. The SMR nuclear waste attributes show both some similarities to the PWR and some significant differences caused by reactor-specific design features. The DU mass is equivalent to or slightly higher than the PWR. Back-end waste attributes for SNF disposition vary, but the differences have a limited impact on long-term repository isolation. SMR designs can vary significantly in SNF volume (and thus heat generation density). However, these differences are amenable to design optimization for handling, storage, transportation, and disposal technologies. Nuclear waste attributes from decommissioning vary depending on design and decommissioning technology choices. Given the analysis results in this study and assuming appropriate waste management system and operational optimization, there appear to be no major challenges to managing SMR nuclear wastes compared to the reference PWR.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Understanding and quantifying electron beam effects during in situ TEM nanomechanical tensile testing on metal thin films

Transmission electron microscopy (TEM) imaging relies on high energy electrons for atomic scale resolution, however, the electrons themselves interact with and may alter the material being imaged. Using an in situ TEM MEMS-based nanomechanical testing technique, the effect of the electron beam (e-beam) on the deformation behavior of nanocrystalline Al and ultrafine-grained Au is investigated and quantified. We show that the e-beam enhances plastic deformation, leading to an increase in plastic strain rate and a decrease in true activation volume V* in Al (28 to 21b 3 , with b being the Burgers vector length). The e-beam has a much weaker effect on Au. The e-beam effect is not caused by knock-on damage, but rather an effective temperature increase due to additional atomic fluctuations provided by the e-beam. The effective temperature increase is larger for Al than Au. This e-beam effect does not change the deformation mechanisms, but instead accelerates the stress-driven, thermally activated plastic deformation. These experiments provide insight into the effects of the e-beam on plastic deformation in different metals and underscore the importance of understanding and quantifying these effects for proper interpretation of measured mechanical properties during in situ TEM experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Accelerated creep profiling: a high-throughput thermal- and stress-gradient approach applied to additive and wrought stainless steel

Here, this study investigates logarithmic creep behavior at temperatures near room temperature in wrought and additively manufactured (AM) 316 L austenitic stainless steel. A novel high-throughput (HiTp) methodology employed thermal gradients to obtain stress- and temperature-dependence of creep behavior. The findings, based on 104 two-week creep tests, reveal significant differences in creep response between wrought and AM materials. Compared to the wrought material, the AM material exhibited a higher activation energy and a lower activation volume. These differences were attributed to the materials’ distinct microstructural features, e.g., dislocation cell structures and precipitate distributions, which alter the susceptibility to dislocation glide creep, particularly at stresses below the yield stress. The HiTp methodology provides both an accelerated determination of low-temperature creep mechanisms, offering critical data for the design and optimization of alloys in near-ambient, high stress applications.

316 L Stainless steel↗