Search NASA⌕ Search

SEARCH · Search NASA

Results for “actuator line method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Validation of Actuator Disk, Actuator Line and Sliding Mesh Methods within the LAVA Solver

In this study the implementation of actuator-disk, actuator-line and sliding-mesh methodologies in the Launch Ascent and Vehicle Aerodynamics (LAVA) solver is described and validated against several test-cases. The different models are validated against available numerical as well as experimental data. Both steady and unsteady Reynolds-Averaged Navier-Stokes (RANS) simulations using the Spallart Allmaras (SA) turbulence model are performed for several different configurations representative of aeroscience applications. The first part of the paper is focused on the verification and validation of the implemented propulsor models. The first validation case is a theoretical rotor in hover, compared with the 1D analytical solution derived from momentum theory. The second validation is the Rotor-Airframe Interaction Model of Georgia Institute of Technology (GIT), representing the application of actuator disks to top-mounted rotorcraft vehicles or unmanned aerial vehicles (UAVs). The third case is a representative configuration for tip-mounted rotor-craft vehicles such as NASA’s X57 airplane. The second part of the paper shows the implemented models applied to realistic engineering configurations such as NASA’s X57 airplane and the R4 Advanced Ducted Propellor (ADT). A modification to the actuator line method in order to represent the blade geometry more closely is proposed and comparisons with simulations modeling the blade utilizing a sliding-mesh approach are made.

ARMD↗
NASA NTRS2000

Robust Inversion and Data Compression in Control Allocation

We present an off-line computational method for control allocation design. The control allocation function delta = F(z)tau = delta (sub 0) (z) mapping commanded body-frame torques to actuator commands is implicitly specified by trim condition delta (sub 0) (z) and by a robust pseudo-inverse problem double vertical line I - G(z) F(z) double vertical line less than epsilon (z) where G(z) is a system Jacobian evaluated at operating point z, z circumflex is an estimate of z, and epsilon (z) less than 1 is a specified error tolerance. The allocation function F(z) = sigma (sub i) psi (z) F (sub i) is computed using a heuristic technique for selecting wavelet basis functions psi and a constrained least-squares criterion for selecting the allocation matrices F (sub i). The method is applied to entry trajectory control allocation for a reusable launch vehicle (X-33).

Hodel, A. Scottedward↗
NASA NTRSDate not supplied

Comparing Methods to Extract Sectional Angle of Attack From Blade-Resolved Rotor Simulations

The angle of attack is widely used to describe the aerodynamics of rotor blades. Models based on lifting lines, actuator lines, and actuator disks use it as a primary variable, assuming the aerodynamics can be represented by the flow around a collection of equivalent 2D airfoils. This paper evaluates the accuracy of existing methods that extract the angle of attack from blade-resolved CFD simulations, towards enabling a direct comparison of angle of attack between blade-resolved and blade-modeled simulations. Results are compared for a 2D airfoil for which the angle of attack is known by definition. The hovering rotor case is also considered, where we look at two different rotor blades. We discuss the factors that impact the accuracy of the 2D predictions. For the 3D rotors, we show that three-dimensional effects in the root and tip regions lead to large discrepancies between methods. This suggests that the very definition of angle of attack is unable to accurately represent the flow in these regions. Finally, based on guidelines that we establish, we propose an alternate method that uses local velocities sampled on a contour located 0.25 chord, or less, away from the airfoil surface and generally yields improved accuracy compared to most existing techniques.

ARMD↗
NASA NTRS1980

Development of a facility for large-scale testing of multistory buildings

Current experimental research pertaining to response of structures subjected to lateral loads such as strong winds or earthquake motions is limited to either tests of single structural components or small scale multistory structures. The feasibility of developing a facility where large scale multistory structures could be loaded to failure is discussed. The test facility would consist of a series of hydraulic actuators mounted on reaction frames currently in use at the Marshall Space Flight Center for structural testing of spacecraft components. The actuators would be controlled from signals computed by an on-line analysis of measured data. This method of loading could be used to simulate inertial forces resisted by a structure behaving in the non linear range of response subjected to motion at the base or to impulses along the height as would occur during a strong earthquake or wind.

Abrams, D. P.↗
NASA NTRS2010

Refreshable Braille Displays Using EAP Actuators

Refreshable Braille can help visually impaired persons benefit from the growing advances in computer technology. The development of such displays in a full screen form is a great challenge due to the need to pack many actuators in small area without interferences. In recent years, various displays using actuators such as piezoelectric stacks have become available in commercial form but most of them are limited to one line Braille code. Researchers in the field of electroactive polymers (EAP) investigated methods of using these materials to form full screen displays. This manuscript reviews the state of the art of producing refreshable Braille displays using EAP-based actuators..

Electroactive Polymers↗
NASA NTRS1995

Robot Motion Planning Among Moving Obstacles

An on-line method is presented for computing the motion of a robot in a dynamic environment subject to the robot dynamics and its actuator constraints. This method is based on the concept of Velocity Obstacle that defines the set of robot velocities that would result in a collision between the robot and a moving obstacle. The problem of motion planning in dynamic environments is addressed.

Robotics Velocity Obstacle↗
NASA NTRS2009

Methodologies for Adaptive Flight Envelope Estimation and Protection

This paper reports the latest development of several techniques for adaptive flight envelope estimation and protection system for aircraft under damage upset conditions. Through the integration of advanced fault detection algorithms, real-time system identification of the damage/faulted aircraft and flight envelop estimation, real-time decision support can be executed autonomously for improving damage tolerance and flight recoverability. Particularly, a bank of adaptive nonlinear fault detection and isolation estimators were developed for flight control actuator faults; a real-time system identification method was developed for assessing the dynamics and performance limitation of impaired aircraft; online learning neural networks were used to approximate selected aircraft dynamics which were then inverted to estimate command margins. As off-line training of network weights is not required, the method has the advantage of adapting to varying flight conditions and different vehicle configurations. The key benefit of the envelope estimation and protection system is that it allows the aircraft to fly close to its limit boundary by constantly updating the controller command limits during flight. The developed techniques were demonstrated on NASA s Generic Transport Model (GTM) simulation environments with simulated actuator faults. Simulation results and remarks on future work are presented.

Tang, Liang↗
NASA NTRS2007

Circuit and Method for Communication Over DC Power Line

A circuit and method for transmitting and receiving on-off-keyed (OOK) signals with fractional signal-to-noise ratios uses available high-temperature silicon- on-insulator (SOI) components to move computational, sensing, and actuation abilities closer to high-temperature or high-ionizing radiation environments such as vehicle engine compartments, deep-hole drilling environments, industrial control and monitoring of processes like smelting, and operations near nuclear reactors and in space. This device allows for the networking of multiple, like nodes to each other and to a central processor. It can do this with nothing more than the already in-situ power wiring of the system. The device s microprocessor allows it to make intelligent decisions within the vehicle operational loop and to effect control outputs to its associated actuators. The figure illustrates how each node converts digital serial data to OOK 18-kHz in transmit mode and vice-versa in receive mode; though operations at lower frequencies or up to a megahertz are within reason using this method and these parts. This innovation s technique modulates a DC power bus with millivolt-level signals through a MOSFET (metal oxide semiconductor field effect transistor) and resistor by OOK. It receives and demodulates this signal from the DC power bus through capacitive coupling at high temperature and in high ionizing radiation environments. The demodulation of the OOK signal is accomplished by using an asynchronous quadrature detection technique realized by a quasi-discrete Fourier transform through use of the quadrature components (0 and 90 phases) of the carrier frequency as generated by the microcontroller and as a function of the selected crystal frequency driving its oscillator. The detected signal is rectified using an absolute-value circuit containing no diodes (diodes being non-operational at high temperatures), and only operational amplifiers. The absolute values of the two phases of the received signal are then summed and hard limited (digitized) by comparing them to a reference level and are then input into a microprocessor as a serial bit stream. The quasi-discrete Fourier transform is performed in high-temperature components (operational amplifiers, analog switches, resistors, and capacitors). The demodulated signal is a serial data stream that is input to the UART (universal asynchronous receiver transmitter) receiver pin of the microprocessor. The OOK of the carrier frequency uses the output of the UART pin as an enabling signal that drives the gate of the MOSFET. Logic low bits enable the carrier frequency (realized by using the 0 phase signal from the microcontroller, though either phase may be used) to be DC-coupled to the power supply bus through a current-limiting resistor mounted between the MOSFET drain and the supply rail. The presence of logic lows on the power supply rail is realized by carrier bursts while logic highs are realized by the absence of bursts.

Krasowski, Michael J.↗
NASA NTRS1991

Robust and real-time control of magnetic bearings for space engines

Currently, NASA Lewis Research Center is developing magnetic bearings for Space Shuttle Main Engine (SSME) turbopumps. The control algorithms which have been used are based on either the proportional-intergral-derivative control (PID) approach or the linear quadratic (LQ) state space approach. These approaches lead to an acceptable performance only when the system model is accurately known, which is seldom true in practice. For example, the rotor eccentricity, which is a major source of vibration at high speeds, cannot be predicted accurately. Furthermore, the dynamics of a rotor shaft, which must be treated as a flexible system to model the elastic rotor shaft, is infinite dimensional in theory and the controller can only be developed on the basis of a finite number of modes. Therefore, the development of the control system is further complicated by the possibility of closed loop system instability because of residual or uncontrolled modes, the so called spillover problem. Consequently, novel control algorithms for magnetic bearings are being developed to be robust to inevitable parametric uncertainties, external disturbances, spillover phenomenon and noise. Also, as pointed out earlier, magnetic bearings must exhibit good performance at a speed over 30,000 rpm. This implies that the sampling period available for the design of a digital control system has to be of the order of 0.5 milli-seconds. Therefore, feedback coefficients and other required controller parameters have to be computed off-line so that the on-line computational burden is extremely small. The development of the robust and real-time control algorithms is based on the sliding mode control theory. In this method, a dynamic system is made to move along a manifold of sliding hyperplanes to the origin of the state space. The number of sliding hyperplanes equals that of actuators. The sliding mode controller has two parts; linear state feedback and nonlinear terms. The nonlinear terms guarantee that the systems would reach the intersection of all sliding hyperplanes and remain on it when bounds on the errors in the system parameters and external disturbances are known. The linear part of the control drives the system to the origin of state space. Another important feature is that the controller parameter can be computed off-line. Consequently, on-line computational burden is small.

Sinha, Alok↗
NASA NTRS1991

A distributed fault-detection and diagnosis system using on-line parameter estimation

The development of a model-based fault-detection and diagnosis system (FDD) is reviewed. The system can be used as an integral part of an intelligent control system. It determines the faults of a system from comparison of the measurements of the system with a priori information represented by the model of the system. The method of modeling a complex system is described and a description of diagnosis models which include process faults is presented. There are three distinct classes of fault modes covered by the system performance model equation: actuator faults, sensor faults, and performance degradation. A system equation for a complete model that describes all three classes of faults is given. The strategy for detecting the fault and estimating the fault parameters using a distributed on-line parameter identification scheme is presented. A two-step approach is proposed. The first step is composed of a group of hypothesis testing modules, (HTM) in parallel processing to test each class of faults. The second step is the fault diagnosis module which checks all the information obtained from the HTM level, isolates the fault, and determines its magnitude. The proposed FDD system was demonstrated by applying it to detect actuator and sensor faults added to a simulation of the Space Shuttle Main Engine. The simulation results show that the proposed FDD system can adequately detect the faults and estimate their magnitudes.

Guo, T.-H.↗
NASA NTRS1984

Optimal quasi-static shape control for large aerospace antennae

In this paper, an on-line control approach which will adjust the steady-state shape of a large antenna arbitarily close to any achievable desired profile is proposed. The method makes use of distributed parameter system theory and allows refocusing using a limited number of control actuators and sensors. The controller gains are calculated by approximating the solution to an infinite-dimensional optimal quasi-static control problem. A very general convergence result for such quasi-static controllers is proved and applied to the antenna controller to show convergence, using any Galerkin (finite-element) approximation method.

Balas, M. J.↗
NASA NTRS1987

Suboptimal shape control for quasi-static distributed-parameter systems

An on-line control approach which will adjust the steady-state shape of a large antenna arbitrarily close to any achievable desired profile is approached. The method makes use of distributed-parameter system theory and allows refocusing using a limited number of control actuators and sensors. The controller gains are calculated by approximating the solution to an infinite-dimensional optimal quasi-static control problem. The controller gain calculation is computationally simpler than that previously proposed. The Galerkin (finite element) approximation method is used for model reduction. It is proved that both gain and state convergence can be achieved by using the proposed approximation scheme.

Balas, M. J.↗
NASA NTRS1985

Experiments in structural dynamics and control using a grid

Future spacecraft are being conceived that are highly flexible and of extreme size. The two features of flexibility and size pose new problems in control system design. Since large scale structures are not testable in ground based facilities, the decision on component placement must be made prior to full-scale tests on the spacecraft. Control law research is directed at solving problems of inadequate modelling knowledge prior to operation required to achieve peak performance. Another crucial problem addressed is accommodating failures in systems with smart components that are physically distributed on highly flexible structures. Parameter adaptive control is a method of promise that provides on-orbit tuning of the control system to improve performance by upgrading the mathematical model of the spacecraft during operation. Two specific questions are answered in this work. They are: What limits does on-line parameter identification with realistic sensors and actuators place on the ultimate achievable performance of a system in the highly flexible environment? Also, how well must the mathematical model used in on-board analytic redundancy be known and what are the reasonable expectations for advanced redundancy management schemes in the highly flexible and distributed component environment?

Montgomery, R. C.↗
NASA NTRS1991

Robust decentralized control laws for the ACES structure

Control system design for the Active Control Technique Evaluation for Spacecraft (ACES) structure at NASA Marshall Space Flight Center is discussed. The primary objective of this experiment is to design controllers that provide substantial reduction of the line-of-sight pointing errors. Satisfaction of this objective requires the controllers to attenuate beam vibration significantly. The primary method chosen for control design is the optimal projection approach for uncertain systems (OPUS). The OPUS design process allows the simultaneous tradeoff of five fundamental issues in control design: actuator sizing, sensor accuracy, controller order, robustness, and system performance. A brief description of the basic ACES configuration is given. The development of the models used for control design and control design for eight system loops that were selected by analysis of test data collected from the structure are discussed. Experimental results showing that very significant performance improvement is achieved when all eight feedback loops are closed are presented.

Collins, Emmanuel G., Jr.↗
NASA NTRS1990

Time optimal feedback control of discrete systems with bounded inputs

Deadbeat control theory gives a feedback solution to the time optimal control of discrete time systems. Experience has shown the results to be impractical because they ignore bounds on the actuator strength. This paper develops two algorithms for generating time optimal control in feedback form for discrete systems with bounded controls. The results are also applicable for generating recovery regions and the set of reachable states. For multiple control problems a method of generating sublayers is developed which decreases off-line and on-line computational effort. Two algorithms are presented with somewhat different computational and storage requirements. The algorithms are practical within certain dimension constraints, and are natural for implementation with parallel processing.

Chen, Xin↗
NASA NTRS1986

Braille Reading Systems

Two proposed electromechanical systems for making braille characters produced relatively inexpensively. Similar in operating principle to dotmatrix printers, two methods use electronically actuated pins to reproduce characters from information stored on magnetic tape. First, one or more pins scanned over blank page and energized at intervals to emboss text on paper, one or more dots at time. Second, handheld device containing one or more character-generator cells used by reader to scan lines of text manually.

Garner, H. D.↗