Search NASA⌕ Search

SEARCH · Search NASA

Results for “aerospace vibration testing design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

Rapid, Approximate Multi-Axis Vibration Testing [Thesis]

The aerospace industry uses vibration shaker tables to perform component durability testing. In these tests a component, piece of equipment, or entire system is attached to a shaker table where it is subjected to dynamic excitation. The goal is to understand how the article under test will perform in its service environment without having to run it through its entire service life via field testing. In a vibration test, an aerospace system or component is qualified if it is shown to survive a test meant to replicate its lifetime service conditions. The test is designed based on recorded field data. To develop a test, a system is taken through all of its intended environments, e.g., transportation, launch, and reentry. Acceleration data measured from these environments is then brought back to the lab and imported into a shaker table controller. The controller then drives a vibration test intended to mimic the acceleration conditions experienced by the system or specific components of the system in the field. However, it is often difficult to match the measured field response in a lab test. This is largely due to the test’s boundary conditions and excitation methods. In a lab test, a shaker table is the excitation source. The two most common shaker table types, differentiated by their number of independent degrees of freedom, are single-axis and multi-axis shaker tables. Multi-axis shakers have the ability to reproduce service environments more realistically, as real accelerations inevitably produce multiple degrees of freedom of excitation simultaneously. Figure 1 depicts a generic multi-axis testing setup on a three-axis shaker table. Often multi-axis tests use six-degree-of-freedom (6DOF) shaker tables. Yet multi-axis shakers are not yet common in the aerospace industry due in part to their high cost and the difficulty for shaker controllers to handle the added complexity. Single-axis shaker tables are much more common. They are not as expensive to purchase and have a wide range of control software options.

42 ENGINEERING↗

High-Temperature Microwave Acoustic Vibration Sensor

High-temperature vibration sensors are desired in a number of contemporary harsh-environment applications, namely: power plants, metallurgy, aerospace, and defense. The detection of vibrations in these applications is important for providing condition-based maintenance (CBM) for electronic, mechanical, and structural systems, thus reducing operating and maintenance costs, improving industry efficiency, and increasing safety. Microwave surface acoustic wave resonator (MSAWR) sensors have the potential of being used as high-temperature vibration sensors due to their proven harsh-environment operation, small size, battery-free, and wireless capability. This paper explores the MSAWR as a vibration sensor mounted and tested up to 500°C. A 193MHz langasite-based MSAWR sensor was attached to a custom-designed constant-stress Inconel cantilever test beam using a high-temperature capable Al 2 O 3 -based adhesive. The beam was mounted in a box furnace and exposed to vibrations using a stainless-steel rod attached to a vibration generator outside the furnace. Here, the resulting measurements at high-temperatures reported in this paper confirm the viability of the MSAWR sensor to detect both vibration frequency and magnitude for high temperature industrial, defense, aerospace, and power sector applications.

42 ENGINEERING↗

FAIR Data and Interpretable AI Framework for Architectured Metamaterials (Final Report)

This research program established a transformative framework for the discovery and design of mechanical metamaterials, which are architected structures engineered to control physical phenomena like sound and vibration in ways natural materials cannot. To overcome the traditional reliance on trial-and-error, the project developed an interpretable Artificial Intelligence (AI) framework that moves beyond "black box" models to reveal the specific geometric patterns—such as "unit-cell templates"—that govern a material’s performance. A major breakthrough was the development of a hierarchical design method, which allows a single material to block vibrations across multiple frequency ranges simultaneously by layering patterns at different scales without them interfering with one another. This was further expanded to include irregular, graph-based designs that use spanning tree algorithms to ensure structural connectivity while allowing for customized, direction-dependent properties like stiffness and acoustic impedance. Beyond design, the project addressed the practicalities of real-world production by developing uncertainty quantification techniques that account for manufacturing defects and material variability, reducing the need for expensive physical testing by orders of magnitude. To speed up the discovery process, the team implemented Gaussian Process Regression and other surrogate models that provide accurate performance predictions at a fraction of the traditional computational cost. The AI-generated designs were successfully validated through fabrication of physical samples and wave propagation experiments, confirming their ability to accurately guide or reflect waves as predicted. By contributing these tools and high-quality FAIR benchmark datasets to the wider scientific community, this work provides a scalable foundation for advancing technologies in aerospace vibration control, medical imaging, and noise reduction.

36 MATERIALS SCIENCE↗

A simulation study of test fixture attachment points for vibration test optimization (MEEN 5440 Final Project)

The aerospace industry uses vibration shaker tables to perform component durability testing. These dynamic environments tests often have a hard time replicating the service environment of a component due to a mismatch in the applied force or the boundary condition. Figure 1 shows the desired outcome of a dynamic environments test. The measured responses in a lab test, ideally, should match the measured response of the service environment field test. One way to address the mismatch between field environment and lab environment is with test fixture design. The test fixture attaches the component under test to the shaker table. Single-axis shakers are the industry standard type of shaker table, and, therefore, test fixtures are often rigid in order to minimize cross-axis responses.

42 ENGINEERING↗

Low-Velocity Impact Behavior of Sandwich Structures with Additively Manufactured Polymer Lattice Cores

Sandwich panel structures are widely used in aerospace, marine, and automotive applications because of their high flexural stiffness, strength-to-weight ratio, good vibration damping, and low through-thickness thermal conductivity. These structures consist of solid face sheets and low-density cellular core structures, which are traditionally based upon honeycomb folded-sheet topologies. The recent advances in additive manufacturing (AM) or 3D printing process allow lattice core configurations to be designed with improved mechanical properties. In this work, the sandwich core is comprised of lattice truss structures (LTS). Two different LTS designs are 3D-printed using acrylonitrile butadiene styrene (ABS) and are tested under low-velocity impact loads. The absorption energy and the failure mechanisms of lattice cells under such loads are investigated. The differences in energy-absorption capabilities are captured by integrating the load–displacement curve found from the impact response. It is observed that selective placement of vertical support struts in the unit-cell results in an increase in the absorption energy of the sandwich panels.

36 MATERIALS SCIENCE↗

Nuclear Materials Packaging, Transportation, and Systems Analysis Group Software Quality Assurance Plan: ANSYS Mechanical Finite Element Analysis Software Version 2023R1

ANSYS Inc. develops and markets engineering simulation software and services used in the aerospace, automotive, manufacturing, electronics, biomedical, energy, defense, and many other industries. ANSYS is dedicated to engineering simulation and is the world’s leading software provider. ANSYS was founded in 1970 and is headquartered in Canonsburg, Pennsylvania. ANSYS provides an engineering analysis tool combining structural, thermal, computational fluid dynamics, acoustic, and electromagnetic simulation capabilities. ANSYS has two main programs, which use the same solvers: (1) Mechanical APDL (ANSYS Design Parametric Language), a Fortran-based coding platform, and (2) ANSYS Workbench, which uses a graphical user interface to aid in finite element analysis implementation. This plan covers both APDL and Workbench. The ANSYS computer program is a large-scale, multipurpose finite element program that can be used to solve several classes of engineering analyses. The analysis capabilities of ANSYS include the ability to solve static and dynamic structural analyses, steady-state and transient heat transfer problems, mode-frequency and buckling eigenvalue problems, static or time-varying magnetic analyses, and various types of field and coupled-field applications. The program contains many special features that allow nonlinearities or secondary effects such as plasticity, large strain, hyperelasticity, creep, swelling, large deflections, contact, stress stiffening, temperature dependency, material anisotropy, and radiation to be included in the solution. As ANSYS has been developed, other special capabilities such as substructuring, submodeling, random vibration, kinetostatics, kinetodynamics, free convection fluid analysis, acoustics, magnetics, piezoelectrics, coupled-field analysis, and design optimization have been added to the program. These capabilities contribute further to making ANSYS a multipurpose analysis tool for varied engineering disciplines. The ANSYS program has been in commercial use for over 50 years and has been used extensively in the aerospace, automotive, construction, electronic, energy services, manufacturing, nuclear, plastics, oil, and steel industries. Additionally, many consulting firms and hundreds of universities have used ANSYS for analysis, research, and educational purposes. ANSYS is recognized worldwide as one of the most widely used and capable programs of its type. Ansys design analysis software is the first created within a quality system with ISO 9001 certification, the internationally accepted quality standard. Product development, testing, maintenance and support processes also meet the United States Nuclear Regulatory Commission's quality requirements, as they have for nearly four decades. The Quality Assurance Service Agreement is suitable for the customers working in the nuclear industry who need to meet specific federal regulations including 10CRF50 Appendix B and provisions of 10CFR21. ANSYS has retained its original International Organization for Standardization (ISO) 9001 accreditation certificate since1995-05-04, It’s current certificate is valid until 2027-05-29.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗