Search NASA⌕ Search

SEARCH · Search NASA

Results for “airframes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Fuel cells for single-aisle regional aircraft: System configuration, performance and cost

A hydrogen fuel cell propelled electric aircraft can compete with incumbent turbofan technologies for single-aisle regional aircraft by coupling design of stack, air handling, thermal management, propulsion, and airframe to optimize performance. The stack operates at 95°C to facilitate heat rejection during take-off and below 75°C during cruise to extend lifetime and is oversized to satisfy power requirements at end of life. A multi-stage turbocompressor with a compression ratio >10 is selected to reach high stack power density at 11,300-m cruise altitude. The propulsion system is configured to accommodate air handling within the core duct, an inclined heat exchanger in the outer duct to limit the nacelle size, and variable area nozzles to independently control mass flows through the core and bypass ducts. The airframe is modified for maximum lift coefficient and longer balanced field length for dramatically reduced thrust during take-off, and the fuselage is stretched by 20% to store liquid hydrogen (LH 2 ). Modularization of power systems promotes safety in one engine inoperative scenarios and allows reaching specific power metrics for stack, balance-of-plant and fuel cell system (FCS), necessary for acceptable take-off weight. In conclusion, cost parity requires increase in FCS lifetime, LH 2 cost reduction, and improved FCS specific power.

Catalyst durability↗
DOE OSTI2026

CFD-Enhanced Calibration of a Multihole Probe for Small Uncrewed Aircraft Systems

A robust calibration method with a 9-hole probe (9HP) for inertial wind vector measurements from a small uncrewed aircraft system (sUAS) is presented. Calibration accuracy is improved by using computational fluid dynamics (CFD) to estimate corrections, such as those for test section blockage, that are generally applied in wind tunnel testing. A method for estimating experimental bias is presented to account for flow variations over the pressure taps as the 9HP is repositioned in the test section. Installation effects from flow over the airframe and upwash produced by the wings are estimated from CFD simulations of the entire airframe at the expected cruise speed. An initial CFD analysis has demonstrated a quantifiable linear relationship between the measured and actual angle of attack as measured from the relative wind frame. In conclusion, the objective of these additional steps is to increase the accuracy of 9HP calibration.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

DEM, DSM, and Cleaned LiDAR Point Cloud Data from the NGEE Arctic UAS Campaigns at the Teller 27 Field Site from 2017 and 2018, Seward Peninsula, Alaska

A Digital Elevation Model (DEM) and Digital Surface Model (DSM) were derived from airborne Light Detection and Ranging (LiDAR) data collected from Los Alamos National Laboratory's (LANL) heavy-lift unoccupied aerial system (UAS) quadcopter and hexacopter platforms operated by Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic) scientists from the EES-14 group at LANL. These data were collected in August 2017 and July 2018 at the NGEE Arctic field site near mile marker 27 of the Bob Blodgett Nome-Teller Memorial Highway between Nome, Alaska and Teller, Alaska. A Vulcan Raven X8 Airframe (Mitcheldean, Gloucestershire, UK), DJI Matrice 600 Pro Airframe (Shenzhen, China), and Routescene UAV LiDARSystem (Edinburgh, Scotland, UK) were used to collect LiDAR data. Following pre-processing in Routescene LidarViewer Pro software, the LiDAR point clouds were cleaned and processed using CloudCompare software to separate ground and off-ground points. A high resolution DEM and DSM were then created using ArcGIS Pro software. This data package contains fully cleaned point clouds of ground and off-ground points (.las), a 25 cm DEM (.tif), and a 25 cm DSM (.tif) for the Teller 27 field site. Ancillary aircraft data, flight mission parameters, weather conditions, and raw lidar data and imagery can be found in the L0 datasets for these campaigns: NGA299 (2017) and NGA297 (2018). Minimally processed point clouds and auxiliary files can be found in the L1 dataset: NGA304 (2017 and 2018).The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a 15-year research effort (2012-2027) to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research.The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska.Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Assessment of Low-Altitude Atmospheric Turbulence Models for Aircraft Aeroelasticity

We investigate the dynamic aeroelastic response of large but slow aircraft in low-altitude atmospheric turbulence. To this end, three turbulence models of increasing fidelity, namely, the one-dimensional von Kármán model, the two-dimensional Kaimal model and full three-dimensional wind fields extracted from large-eddy simulations (LES) are used to simulate ambient turbulence near the ground. Load calculations and flight trajectory predictions are conducted for a representative high-aspect-ratio wing aircraft, using a fully coupled nonlinear flight dynamics/aeroelastic model, when it operates in background atmospheric turbulence generated by the aforementioned models. Comparison of load envelopes and spectral content, on vehicles of varying flexibility, shows strong dependency between the selected turbulence model and aircraft aeroelastic response (e.g. 58% difference in the predicted magnitude of the wing root bending moment between LES and von Kármán models). This is mainly due to the presence of large flow structures at low altitudes that have comparable dimensions to the vehicle, and which despite the relatively small wind speeds within the Earth boundary layer, result in overall high load events for slow-moving vehicles. Results show that one-dimensional models that do not capture those effects provide fairly non-conservative load estimates and are unsuitable for very flexible airframe design.

atmospheric turbulence↗
DOE OSTI2025

LiDAR Point Cloud Data from the 2018 NGEE Arctic UAS Campaign at the Teller 47 Field Site, Seward Peninsula, Alaska

Airborne remote sensing data collected from Los Alamos National Laboratory’s (LANL) heavy-lift unoccupied aerial system (UAS) hexacopter platform operated by NGEE Arctic scientists from the EES-14 group at Los Alamos National Laboratory. These data were collected in July 2018 at a field site near mile marker 47 along the Teller Road between Nome, Alaska and Teller, Alaska. A DJI Matrice 600 Pro Airframe and Routescene UAV LiDAR System was used to collect LiDAR data. The LiDAR data has undergone basic post-processing using Routescene LidarViewer Pro software to create point cloud data (.laz files). This data package contains point clouds (.laz), processing metadata files (json.lvp), and post-processed kinematic files (.csv). Ancillary aircraft data, flight mission parameters, weather conditions, and lidar data and imagery can be found in NGA281 (https://doi.org/10.5440/1671794).The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

New Predictive Capabilities for Nuclear Weapons in Composite Fires

The prevalence of flammable carbon-based composite airframe materials and their use in high-temperature nuclear weapon re-entry systems requires analysts to address the abnormal thermal environment hazards associated with composite material fires. These fires tend to burn very differently than conventional fuel fires, usually burning less intensely, but much longer. This could lead to challenges in understanding margins in classic safety themes. The technical challenges in modeling the phenomena associated with these new types of fires are considerable, but new models have been developed. Their predictions have been compared with well-documented measurements of a vertical porous burner fire, known as a "wall fire" (a "wall-fire" validation simulation is reflected in the figures below). These measurements were conducted at FMGlobal, a mutual insurance company with a strong fire risk management program, as part of an ongoing collaboration between Sandia and FMGlobal. To date, the "wall-fire" scenario has been set up and initial model assessments with grid refinement studies have been conducted focusing on mesh resolutions suitable for full weapon system simulations. This work will continue with further verification and validation tasks assessing the predictions of the new model. Future work will address specific aspects of the wall models that are lacking in their predictive ability.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2023

Exploring the Performance Boundaries of a Small Reconfigurable Multi-Mission UAV through Multidisciplinary Analysis

The performance of a small reconfigurable unmanned aerial vehicle (UAV) is evaluated, combining a multidisciplinary approach in the computational analysis of additive manufactured structures, fluid dynamics, and experiments. Reconfigurable UAVs promise cost savings and efficiency, without sacrificing performance, while demonstrating versatility to fulfill different mission profiles. The use of computational fluid dynamics (CFD) in UAV design produces higher accuracy aerodynamic data, which is particularly important for complex aircraft concepts such as blended wing bodies. To address challenges relating to anisotropic materials, the Tsai–Wu failure criterion is applied to the structural analysis, using CFD solutions as load inputs. Aerodynamic performance results show the low-speed variant attains an endurance of 1 h, 48 min, whereas its high-speed counterpart is 29 min at a 66.7% higher cruise speed. Each variant serves different aspects of small UAS deployment, with low speed envisioned for high-endurance surveying, and high speed for long-range or time-critical missions such as delivery. The experimental and simulation results suggest room for design iteration, in wing area and geometry adjustments. Structural simulations demonstrated the need for airframe improvements to the low-speed configuration. This paper highlights the potential of reconfigurable UAVs to be useful across multiple industries, advocating for further research and design improvements.

42 ENGINEERING↗
DOE OSTI2022

L0 Data from the 2018 NGEE Arctic LiDAR and Imagery Unoccupied Aerial System Campaign at the Teller 47 Field Site, Seward Peninsula, Alaska

Airborne remote sensing data collected from Los Alamos National Laboratory's (LANL) heavy-lift unoccupied aerial system (UAS) hexacopter platform operated by NGEE Arctic scientists from EES-14 (Earth System Observations group) at Los Alamos National Laboratory. These data were collected in July 2018 at a field site near mile marker 47 along the Teller road between Nome, Alaska and Teller, Alaska. A DJI Matrice 600 Pro Airframe and Routescene UAV LiDARSystem was used to collect LiDAR data, and DJI Phantom 4 Advanced was used to collect optical red/green/blue (RGB) imagery at regular intervals along 11 flight paths. This data package contains unprocessed data products (processing level 0) including flight paths, raw photos, and raw lidar data files (*.kml, *.jpg, and *.lpd formats). Ancillary aircraft data, flight mission parameters, and general flight conditions are also included (see Supplemental Files, *.rinex, and *.rtcm3 files). The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy’s Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy’s Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

L0 Data from the 2018 NGEE Arctic LiDAR and Imagery Unoccupied Aerial System Campaign at the Teller 27 Field Site, Seward Peninsula, Alaska

Airborne remote sensing data collected from Los Alamos National Laboratory's (LANL) heavy-lift unoccupied aerial system (UAS) hexacopter platform operated by NGEE Arctic scientists from the EES-14 group at Los Alamos National Laboratory. These data were collected in July 2018 at a field site near mile marker 27 along the Teller road between Nome, Alaska and Teller, Alaska. A DJI Matrice 600 Pro Airframe and Routescene UAV LiDARSystem was used to collect LiDAR data along 12 flight paths, and DJI Phantom 4 Advanced was used to collect optical red/green/blue (RGB) imagery at regular intervals along 5 flight paths. This data package contains unprocessed data products (processing level 0) including flight paths, raw photos, and raw lidar data files (*.kml, *.jpg, and *.lpd formats). Ancillary aircraft data, flight mission parameters, and general flight conditions are also included (see Supplemental Files, *.rinex, and *.rtcm3 files). NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research.- The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

LiDAR Point Cloud Data from the 2018 NGEE Arctic UAS Campaign at the Kougarok 64 Field Site, Seward Peninsula, Alaska

Airborne remote sensing data collected from Los Alamos National Laboratory's (LANL) heavy-lift unoccupied aerial system (UAS) hexacopter platform operated by NGEE Arctic scientists from the EES-14 group at Los Alamos National Laboratory. These data were collected in July 2018 at a field site near mile marker 64 along the Kougarok road (Nome-Taylor Highway) between Nome, Alaska and Taylor, Alaska. A DJI Matrice 600 Pro Airframe and Routescene UAV LiDARSystem was used to collect LiDAR data. The LiDAR data has undergone basic post-processing using Routescene LidarViewer Pro software to create point cloud data (.laz files). This data package contains point clouds (.laz), processing metadata files (json.lvp), and post-processed kinematic files (.csv). Ancillary aircraft data, flight mission parameters, weather conditions, raw LiDAR data, and RGB imagery can be found in NGA298.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗