Search NASA⌕ Search

SEARCH · Search NASA

Results for “altimetry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Comparison of radar-altimetry data over Greenland with surface topography derived from airborne laser altimetry

During the Summers of 1991, 1992, and 1993, NASA flew a scanning laser altimeter over transects of the Greenland ice sheet. Airplane location was measured precisely using differential Global Positioning System (GPS) surveying techniques. This allowed all altimetry data to be reduced to an estimate of ice surface elevations relative to the Earth ellipsoid. Repeat flights over the same areas indicate data consistency to 10 to 20 cm. Many of the aircraft flights were made along the ERS-1 'radar-altimeter footprint track' for a commissioning phase orbit. Rigorous comparison between the ERS-1 altimeter measurements and those from the laser altimeter will require analysis of individual ERS-1 altimeter waveforms, and since the information needed to do this is not yet available, results from comparison of TOPEX (Topology Ocean Experiment) Poseidon (T/P) radar altimetry data with laser data obtained at the northernmost limit of the T/P orbits are presented.

Thomas, R. H.↗
NASA NTRS2021

Accuracy Assessment of Global Internal-Tide Models Using Satellite Altimetry Models Using Satellite Altimetry

Altimeter measurements are corrected for several geophysical parameters in order to access ocean signals of interest, like mesoscale or sub-mesoscale variability. The ocean tide is one of the most critical corrections due to the amplitude of the tidal elevations and to the aliasing phenomena of high-frequency signals into the lower-frequency band, but the internal-tide signatures at the ocean surface are not yet corrected globally. Internal tides can have a signature of several centimeters at the surface with wavelengths of about 50–250 km for the first mode and even smaller scales for higher-order modes. The goals of the upcoming Surface Water Ocean Topography (SWOT) mission and other high-resolution ocean measurements make the correction of these small-scale signals a challenge, as the correction of all tidal variability becomes mandatory to access accurate measurements of other oceanic signals. In this context, several scientific teams are working on the development of new internal-tide models, taking advantage of the very long altimeter time series now available, which represent an unprecedented and valuable global ocean database. The internal-tide models presented here focus on the coherent internal-tide signal and they are of three types: empirical models based upon analysis of existing altimeter missions, an assimilative model and a three-dimensional hydrodynamic model. A detailed comparison and validation of these internal-tide models is proposed using existing satellite altimeter databases. The analysis focuses on the four main tidal constituents: M2, K1, O1 and S2. The validation process is based on a statistical analysis of multi-mission altimetry including Jason-2 and Cryosphere Satellite-2 data. The results show a significant altimeter variance reduction when using internal-tide corrections in all ocean regions where internal tides are generating or propagating. A complementary spectral analysis also gives some estimation of the performance of each model as a function of wavelength and some insight into the residual non-stationary part of internal tides in the different regions of interest. This work led to the implementation of a new internal-tide correction (ZARON'one) in the next geophysical data records version-F (GDR-F) standards.

Loren Carrere↗
NASA NTRS2012

Twenty Years of Progress on Global Ocean Tides: The Impact of Satellite Altimetry

At the dawn of the era of high-precision altimetry, before the launch of TOPEX/Poseidon, ocean tides were properly viewed as a source of noise--tidal variations in ocean height would represent a very substantial fraction of what the altimeter measures, and would have to be accurately predicted and subtracted if altimetry were to achieve its potential for ocean and climate studies. But to the extent that the altimetry could be severely contaminated by tides, it also represented an unprecedented global-scale tidal data set. These new data, together with research stimulated by the need for accurate tidal corrections, led to a renaissance in tidal studies in the oceanographic community. In this paper we review contributions of altimetry to tidal science over the past 20 years, emphasizing recent progress. Mapping of tides has now been extended from the early focus on major constituents in the open ocean to include minor constituents, (e.g., long-period tides; non-linear tides in shelf waters, and in the open ocean), and into shallow and coastal waters. Global and spatially local estimates of tidal energy balance have been refined, and the role of internal tide conversion in dissipating barotropic tidal energy is now well established through modeling, altimetry, and in situ observations. However, energy budgets for internal tides, and the role of tidal dissipation in vertical ocean mixing remain controversial topics. Altimetry may contribute to resolving some of these important questions through improved mapping of low-mode internal tides. This area has advanced significantly in recent years, with several global maps now available, and progress on constraining temporally incoherent components. For the future, new applications of altimetry (e.g., in the coastal ocean, where barotropic tidal models remain inadequate), and new mission concepts (studies of the submesoscale with SWOT, which will require correction for internal tides) may bring us full circle, again pushing further development of tidal models as corrections.

Egbert, Gary↗
NASA NTRS2021

Altimetry for the Future: Building on 25 Years of Progress

In 2018 we celebrated 25 years of development of radar altimetry, and the progress achieved by this methodology in the fields of global and coastal oceanography, hydrology, geodesy and cryospheric sciences. Many symbolic major events have celebrated these developments, e.g., in Venice, Italy, the 15th (2006) and 20th (2012) years of progress and more recently, in 2018, in Ponta Delgada, Portugal, 25 Years of Progress in Radar Altimetry. On this latter occasion it was decided to collect contributions of scientists, engineers and managers involved in the worldwide altimetry community to depict the state of altimetry and propose recommendations for the altimetry of the future. This paper summarizes contributions and recommendations that were collected and provides guidance for future mission design, research activities, and sustainable operational radar altimetry data exploitation. Recommendations provided are fundamental for optimizing further scientific and operational advances of oceanographic observations by altimetry, including requirements for spatial and temporal resolution of altimetric measurements, their accuracy and continuity. There are also new challenges and new openings mentioned in the paper that are particularly crucial for observations at higher latitudes, for coastal oceanography, for cryospheric studies and for hydrology. The paper starts with a general introduction followed by a section on Earth System Science including Ocean Dynamics, Sea Level, the Coastal Ocean, Hydrology, the Cryosphere and Polar Oceans and the ‘‘Green” Ocean, extending the frontier from biogeochemistry to marine ecology. Applications are described in a subsequent section, which covers Operational Oceanography, Weather, Hurricane Wave and Wind Forecasting, Climate projection. Instruments’ development and satellite missions’ evolutions are described in a fourth section. A fifth section covers the key observations that altimeters provide and their potential complements, from other Earth observation measurements to in situ data. Section 6 identifies the data and methods and provides some accuracy and resolution requirements for the wet tropospheric correction, the orbit and other geodetic requirements, the Mean Sea Surface, Geoid and Mean Dynamic Topography, Calibration and Validation, data accuracy, data access and handling (including the DUACS system). Section 7 brings a transversal view on scales, integration, artificial intelligence, and capacity building (education and training). Section 8 reviews the programmatic issues followed by a conclusion.

Saleh Abdalla↗
NASA NTRS1993

Geostatistical evaluation of satellite radar altimetry for high-resolution mapping of Lambert Glacier, Antarctica

The potential of satellite radar altimetry for high-resolution mapping of Antarctic ice streams is evaluated, using retracked and slope-corrected data from the Lambert Glacier and Amery Ice Shelf area, East Antarctica, acquired by Geosat during the Exact Repeat Mission (ERM), 1986-89. The map area includes lower Lambert Glacier north of 72.18 deg S, the southern Amery Ice Shelf, and the grounded inland ice sheet on both sides. The Geosat ERM altimetry is found to provide substantially more complete coverage than the 1978 Seasat altimetry, due to improved tracking. Variogram methods are used to estimate the noise levels in the data as a function of position throughout the map area. The spatial structure in the data is quantified by constructing experimental variograms using altimetry from the area of the grounding zone of Lambert Glacier, which is the area chiefly of interest in this topographically complex region. Kriging is employed to invert the along-track height measurements onto a fine-scale 3 km grid. The unsmoothed along-track Geosat ERM altimetry yields spatially continuous maps showing the main topographic features of lower Lambert Glacier, upper Amery Ice Shelf and the adjacent inland ice sheet. The probable position of the grounding line of Lambert Glacier is identified from a break in slope at the grounded ice/floating ice transition. The approximate standard error of the kriged map is inferred from the data noise levels.

Herzfeld, Ute C.↗
NASA NTRS1978

Detailed gravity anomalies from GEOS-3 satellite altimetry data

A technique for deriving mean gravity anomalies from dense altimetry data was developed. A combination of both deterministic and statistical techniques was used. The basic mathematical model was based on the Stokes' equation which describes the analytical relationship between mean gravity anomalies and geoid undulations at a point; this undulation is a linear function of the altimetry data at that point. The overdetermined problem resulting from the excessive altimetry data available was solved using Least-Squares principles. These principles enable the simultaneous estimation of the associated standard deviations reflecting the internal consistency based on the accuracy estimates provided for the altimetry data as well as for the terrestrial anomaly data. Several test computations were made of the anomalies and their accuracy estimates using GOES-3 data.

Gopalapillai, G. S.↗
NASA NTRS1991

Multi-Year Elevation Changes Near the West Margin of the Greenland Ice Sheet from Satellite Radar Altimetry

Mean changes in the surface elevation near the west margin of the Greenland ice sheet are measured using Seasat altimetry and altimetry from the Geosat Exact Repeat Mission (ERM). The Seasat data extend from early July through early October 1978. The ERM data extend from winter 1986-87 through fall 1988. Both seasonal and multi-year changes are measured using altimetry referenced to GEM T2 orbits. The possible effects of orbit error are minimized by adjusting the orbits into a common ocean surface. Seasonal mean changes in the surface height are recognizable during the Geosat ERM. The multi-year measurements indicate the surface was lower by 0.4 +/- 0.4 m on average in late summer 1987 than in late summer 1978. The surface was lower by 0.2 +/- 0.5 m on average in late summer 1988 than in late summer 1978. As a control case, the computations art also carried out using altimetry referenced to orbits not adjusted into a common ocean surface.

Lingle, Craig S.↗
NASA NTRS1999

Preliminary Global Topographic Model of Mars Based on MOLA Altimetry, Earth-Based Radar, and Viking, Mariner and MGS Occultations

The recent altimetry data acquired by MOLA over the northern hemisphere of Mars have been combined with the Earth-based radar data obtained between 1971 and 1982, and occultation measurements of the Viking 1 and 2 Orbiters, Mariner 9, and MGS to derive a global model of the shape and topography of Mars. This preliminary model has a horizontal resolution of about 300 km. Vertical accuracy is on average a few hundred meters in the region of the data. Datasets: The altimetry and radar datasets were individually binned in 1.25 degree grids and merged with the occultation data. The Viking and Mariner occultation data in the northern hemisphere were excluded from the combined dataset where MOLA altimetry were available. The laser altimetry provided extensive and almost complete coverage of the northern hemisphere north of latitude 30 while the radar provided longitudinal coverage at several latitude bands between 23N and 23S. South of this region the only data were occultations. The majority of the occultations were obtained from Mariner 9, and the rest from Viking 1 & 2, and MGS. Earlier studies had shown that the Viking and Mariner occultations were on average only accurate to 500 meters. The recent MGS occultations are accurate to a few tens of meters. However, the highest southern latitude reached by the MGS occultations is only about 64S and data near the target region for the Mars 98 lander is limited to a few Viking and Mariner observations of relatively poor quality. In addition to the above datasets the locations of the Viking 1, Viking 2, and Pathfinder landers, obtained from the radio tracking of their signals, were included.

Smith, David E.↗
NASA NTRS2000

Using Airborne Laser Altimetry to Detect Topographic Change at Long Valley Caldera California

The topography of the Long Valley caldera, California, was sampled using airborne laser altimetry in 1993, 1995, and 1997 to test the feasibility of using airborne laser altimetry for monitoring deformation of volcanic origin. Results show the laser altimeters are able to resolve subtle topographic features such as a gradual slope and to detect small transient changes in lake elevation. Crossover and repeat pass analyses of laser tracks indicate decimeter-level vertical precision is obtained over flat and low-sloped terrain for altimeter systems performing waveform digitization. Comparisons with complementary, ground-based CPS data at a site close to Bishop airport indicate that the laser and GPS-derived elevations agree to within the error inherent in the measurement and that horizontal locations agree to within the radius of the laser footprint. A comparison of the data at two sites, one where no change and the other where the maximum amount of vertical uplift is expected, indicates approximately 10 cm of relative uplift occurred 1993-1997, in line with predictions from continuous CPS measurements in the region. Extensive terrain mapping flights during the 1995 and 1997 missions demonstrate some of the unique abilities of laser altimetry; the straightforward creation of high resolution, high accuracy digital elevation models of overflown terrain, and the ability to determine ground topography in the presence of significant ground cover such as dense tree canopies. These capabilities make laser altimetry an attractive technique for quantifying topographic change of volcanic origin, especially in forested regions of the world where other remote sensing instruments have difficulty detecting the underlying topography.

Hofton, M. A.↗
NASA NTRS1999

Using Airborne Laser Altimetry to Detect Topographic Change at Long Valley Caldera, California

The topography of the Long Valley caldera, California, was sampled using airborne laser altimetry in 1993, 1995, and 1997 to test the feasibility of using airborne laser altimetry for monitoring deformation of volcanic origin. Results show the laser altimeters are able to resolve subtle topographic features such as a gradual slope and to detect small transient changes in lake elevation. Crossover and repeat pass analyses of laser tracks indicate decimeter-level vertical precision is obtained over flat and low-sloped terrain for altimeter systems performing waveform digitization. Comparisons with complementary, ground-based GPS data at a site close to Bishop airport indicate that the laser and GPS-derived elevations agree to within the error inherent in the measurement and that horizontal locations agree to within the radius of the laser footprint. A comparison of the data at two sites, one where no change and the other where the maximum amount of vertical uplift is expected, indicates approximately 10 cm of relative uplift occurred 1993-1997, in line with predictions from continuous GPS measurements in the region. Extensive terrain mapping flights during the 1995 and 1997 missions demonstrate some of the unique abilities of laser altimetry; the straightforward creation of high resolution, high accuracy digital elevation models of overflown terrain, and the ability to determine ground topography in the presence of significant ground cover such as dense tree canopies. These capabilities make laser altimetry an attractive technique for quantifying topographic change of volcanic origin, especially in forested regions of the world where other remote sensing instruments have difficulty detecting the underlying topography.

Hofton, M. A.↗
NASA NTRS2001

Implementation of Altimetry Data in the GIPSY POD Software Package

Altimetry data has been used extensively to acquire data about characteristics of the Earth, the Moon, and Mars. More recently, the idea of using altimetry for orbit determination has also been explored. This report discusses modifications to JPL's GIPSY/OASIS II software to include altimetry data as an observation type for precise orbit determination. The mathematical foundation of using altimetry for the purpose of orbit determination is presented, along with results.

Stauch, Jason R.↗
NASA NTRS2014

A Super-Resolution Laser Altimetry Concept

A super-resolution laser altimetry technique has been proposed to provide improved lidar altimetry from Cloud Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) lidar data, and it is applicable to other similar atmospheric profiling lidar with low-pass filters. To achieve high altimetry resolution, the new technique relies on an empirical relationship between the peak signal ratio and the distance between land surface and the peak signal range bin center, which is directly derived from the CALIPSO lidar measurements and does not require the CALIPSO's transient response. The CALIPSO surface elevation results in Northern America retrieved by the new technique agree with the National Elevation Database high resolution elevation maps, and the comparisons suggest that the precision of the technique is much better than 1.4 m. The preliminary data product of land surface elevation retrieved by the new technique from CALIPSO lidar measurements is available to the altimetry community for evaluation.

Lu, Xiaomei↗
NASA NTRS2015

Satellite Radar Altimetry for Monitoring Small Rivers and Lakes in Indonesia

Remote sensing and satellite geodetic observations are capable of hydrologic monitoring of freshwater resources. Although satellite radar altimetry has been used in monitoring water level or discharge, its use is often limited to monitoring large rivers ( >1 km) with longer interval periods (>1 week) because of its low temporal and spatial resolutions (i.e., satellite revisit period). Several studies have reported successful retrieval of water levels for small rivers as narrow as 40m. However, processing current satellite altimetry signals for such small water bodies to retrieve water levels accurately remains challenging. Physically, the radar signal returned by water bodies smaller than the satellite footprint is most likely contaminated by non-water surfaces, which may degrade the measurement quality. In order to address this scientific challenge, we carefully selected the waveform shapes corresponding to the range measurement resulting from standard retrackers for the European Space Agency's (ESA's) Envisat (Environmental Satellite) radar altimetry. We applied this approach to small (40-200m in width) and medium-sized (200-800m in width) rivers and small lakes (extent<1000 sq km) in the humid tropics of Southeast Asia, specifically in Indonesia. This is the first study that explored the ability of satellite altimetry to monitor small water bodies in Indonesia.

Satellite↗
NASA NTRS2019

Assessment of Altimetry Using Ground-Based GPS Data from the 88S Traverse, Antarctica, in Support of ICESat-2

We conducted a 750 km kinematic GPS survey, referred to as the 88S Traverse, based out of South Pole Station, Antarctica, between December 2017 and January 2018. This ground-based survey was designed to validate space-borne altimetry and airborne altimetry developed at NASA. The 88S Traverse intersects 20% of the ICESat-2 satellite orbits on a route that has been flown by two different Operation IceBridge airborne laser altimeters: the Airborne Topographic Mapper (ATM; 26 October 2014) and the University of Alaska Fairbanks (UAF) Lidar (30 November and 3 December 2017). Here we present an overview of the ground-based GPS data quality and a quantitative assessment of the airborne laser altimetry over a flat section of the ice sheet interior. Results indicate that the GPS data are internally consistent (1:1+- 4:1 cm). Relative to the ground-based 88S Traverse data, the elevation biases for ATM and the UAF lidar range from -9:5 to 3.6 cm, while surface measurement precisions are equal to or better than 14.1 cm. These results suggest that the ground-based GPS data and airborne altimetry data are appropriate for the validation of ICESat-2 surface elevation data.

Brunt, Kelly M.↗
NASA NTRS2021

The Mean Seasonal Cycle in Relative Sea Level From Satellite Altimetry and Gravimetry

Satellite altimetry and gravimetry are used to determine the mean seasonal cycle in relative sea level, a quantity relevant to coastal flooding and related applications. The main harmonics (annual, semiannual, terannual) are estimated from 25 years of gridded altimetry, while several conventional altimeter “corrections” (gravitational tide, pole tide, and inverted barometer) are restored. To transform from absolute to relative sea levels, a model of vertical land motion is developed from a high-resolution seasonal mass inversion estimated from satellite gravimetry. An adjustment for annual geocenter motion accounts for use of a center-of-mass reference frame in satellite orbit determination. A set of 544 test tide gauges, from which seasonal harmonics have been estimated from hourly measurements, is used to assess how accurately each adjustment to the altimeter data helps converge the results to true relative sea levels. At these gauges, the median annual and semiannual amplitudes are 7.1 cm and 2.2 cm, respectively. The root-mean-square differences with altimetry are 3.24 and 1.17 cm, respectively, which are reduced to 1.93 and 0.86 cm after restoration of corrections and adjustment for land motion. Example outliers highlight some limitations of present-day coastal altimetry owing to inadequate spatial resolution: upwelling and currents off Oregon and wave setup at Minamitori Island.

Richard D Ray↗
NASA NTRS2024

Quantifying Volumetric Scattering Bias in ICESat-2 and Operation IceBridge Altimetry Over Greenland Firn and Aged Snow

The Ice, Cloud, and Land Elevation Satellite-2 (ICESat-2) mission has collected surface elevation measurements for over 5 years. ICESat-2 carries an instrument that emits laser light at 532 nm, and ice and snow absorb weakly at this wavelength. Previous modeling studies found that melting snow could induce significant bias to altimetry signals, but there is no formal assessment on ICESat-2 acquisitions during the melting season. We performed two case studies over the Greenland Ice Sheet to quantify bias in ICESat-2 signals over snow: one to validate Airborne Topographic Mapper (ATM) data against Next Generation Airborne Visible/Infrared Imaging Spectrometer (AVIRIS-NG) grain sizes, and a second to estimate ICESat-2 bias relative to ATM. We used snow optical grain sizes derived from ATM and AVIRIS-NG to attribute altimetry bias to snowpack properties. For the first case study, the mean and standard deviation of optical grain sizes were 340 ± 65 µm (AVIRIS-NG) and 670 ± 420 µm (ATM). A mean altimetry bias of 4.81 ± 1.76 cm was found for ATM, with larger biases linked to increases in grain size. In the second case study, we found a mean grain size of 910 ± 381 µm and biases of 6.42 ± 1.77 cm (ICESat-2) and 9.82 ± 0.97 cm (ATM). The grain sizes and densities needed to recreate biases with a model are uncommon in nature, so we propose that additional surface attributes must be considered to characterize ICESat-2 bias over snow. The altimetry biases are within the accuracy requirements of the ICESat-2 mission, but we cannot rule out more significant errors over coarse-grained snow.

Zachary Fair↗
DOE OSTI2026

Improving coastal water level estimation by merging nadir-only satellite altimetry data into a hydrodynamic model

Providing robust real time flood warnings is of paramount importance to coastal communities. Although state-of-the-art hydrodynamic models are capable of robustly predicting Coastal Water Levels (CWL), unresolved drivers affecting level fluctuations are often not represented by the model governing equations. This work evaluates a novel method to improve the performance of the ADvanced CIRCulation (ADCIRC) hydrodynamic model by assimilating observations from four nadir-only satellite altimetry missions against a set of National Oceanic and Atmospheric Administration (NOAA) gauge stations located across the entire U.S. East Coast. Two different types of simulations were performed – Open Loop (OL) and Data Assimilation (DA). Five different simulations were performed where four different satellite altimetry observations were assimilated individually and combined with two different scenarios – with and without considering the data quality flags. Results indicate that, despite their limited spatial coverage, merging nadir-only observations into ADCIRC from the newly launched Surface Water and Ocean Topography (SWOT)’s nadir altimeter can improve the model performance at 76% of the gauge locations, whereas Sentinel-6 improves 73% of the total locations, Jason-3 74%, and SARAL 21%. Furthermore, combining observations from SWOT-nadir, Jason-3, and Sentinel-6 can improve the ADCIRC performance at more than 80% of the gauge locations for 107-day simulation. Nadir-only satellite altimetry observations can be useful for improving the model performance even if flagged as “poor quality” near the coast. When the flagged data are disregarded, SWOT can improve ADCIRC at 78%, Sentinel-6 at 73%, Jason-3 at 53%, and SARAL at 21% of the gauge locations. The ability to improve the model simulations largely depends on the availability of a satellite overpass nearby. Therefore, model performance can be further enhanced if satellite observations are available during a storm surge event, stressing the importance of frequent satellite overpasses.

Aafnan Bhuiyan, Soelem↗
NASA NTRS1975

Calibration and evaluation of Skylab altimetry for geodetic determination of the geoid

The author has identified the following significant results. The Skylab altimeter experiment has proven the capability of the altimeter for measurement of sea surface topography. The geometric determination of the geoid/mean sea level from satellite altimetry is a new approach having significant applications in many disciplines including geodesy and oceanography. A generalized least squares collocation technique was developed for determination of the geoid from altimetry data. The technique solves for the altimetry geoid and determines one bias term for the combined effect of sea state, orbit, tides, geoid, and instrument error using sparse ground truth data. The influence of errors in orbit and a priori geoid values are discussed. Although the Skylab altimeter instrument accuracy is about plus or minus 1m, significant results were obtained in identification of large geoidal features such as over the Puerto Rico trench. Comparison of the results of several passes shows that good agreement exists between the general slopes of the altimeter geoid and the ground truth, and that the altimeter appears to be capable of providing more details than are now available with best known geoids.

Mourad, A. G.↗