Search NASA⌕ Search

SEARCH · Search NASA

Results for “ballooning mode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Nonlinear saturation of ballooning modes in stellarators

Ballooning mode saturation is investigated in realistic stellarator configurations using the flux tube approach of Ham et al (2018 Plasma Phys. Control. Fusion 60 075017), Ham et al (2016 Phys. Rev. Lett. 116 235001). The method is adapted to account for the lack of exact force balance in stellarator equilibrium solvers that assume existence of nested flux surfaces. A variational approach for calculating flux tube energy is developed to overcome this force error problem in stellarator numerical equilibria. Saturated (equilibrium) flux tube states that cross 10%–20% of the plasma minor radius are shown to exist for linearly ballooning unstable profiles. It is shown that several features of the displaced flux tube structure in a full nonlinear MHD simulation of Wendelstein 7X are reproduced by our model. Saturated states are found in a compact stellarator equilibrium close but below the marginal ballooning linear instability, i.e. the unperturbed equilibrium is metastable. This suggests that edge-localized-mode-like explosive MHD behavior may be possible in stellarators.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1990

Ballooning mode instability at the plasmapause

The ballooning mode instability, which can excite hydromagnetic waves at the plasmapause, is studied in the presence of azimuthal plasma flows induced during geomagnetically disturbed periods. A general sufficient criterion for the ballooning mode stability is derived, for a change in the potential energy greater than or equal to 0, which involves the integration over an entire field line. A local stability analysis at the equatorial plasmapause region shows that the ballooning modes could be spontaneously generated via instability under at least two conditions: one is similar to the usual interchange condition, and the second to the quasi-interchange modes. Both of these local instability conditions can be derived from the general stability criterion. Finally an exact solution for the equilibrium state with flow is derived analytically, and the change in the potential energy is computed numerically. It is found that, in the cases studied, the flow does not spontaneously excite the ballooning modes; it only further stabilizes (or destabilizes) the ballooning spectrum if originally the system is stable (or unstable). The analysis would be useful for the interpretation of some of the low-frequency modes observed at the ground and near the equatorial plasmapause.

Lakhina, G. S.↗
DOE OSTI2023

Impact of toroidal rotation on the resistive ballooning modes in ASDEX Upgrade tokamak

Abstract In this work, we investigate the behavior of instabilities appearing between type-I edge localized modes (ELMs), with increasing neutral beam injection (NBI) power concomitant increase in toroidal rotation, and compare it to the modeling result of the linear magneto-hydrodynamic (MHD) code CASTOR3D. An injection of one NBI beam, increasing toroidal rotation, results in the mode slowing down from 12 kHz to 7 kHz, and its associated radial displacement decreases from 5 mm to 3.5 mm. In addition, modes shift radially outwards towards higher q , decreasing their poloidal mode numbers. The mode velocity is measured to be close to the E × B velocity with significant uncertainties. Through a set of CASTOR3D simulations with varying profiles, resistivity has been identified as the primary contributor to the growth rates. Only a small stabilizing effect due to toroidal rotation has been observed. While experimental results show a decrease of mode frequency with rotation, the opposite trend is observed in modeling. Reasons for discrepancies between modeling and experiment are discussed. Nevertheless, a main contributor to the mode frequency has been identified to be rotation velocity. CASTOR3D classifies modes as resistive ballooning modes as they do not appear unstable in ideal MHD.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1994

Anisotropic Alfven-ballooning modes in Earth's magnetosphere

We have carried out a theoretical analysis of the stability and parallel structure of coupled shear Alfven and slow magnetosonic waves in Earth's inner magnetopause (i.e., at equatorial distances between about five and ten Earth radii) including effects of finite anisotropic Grad-Shafranov equation yields an approximate self-consistent magnetohydrodynamic (MHD) equilibrium. This MHD equilibrium is used in the numerical solution of a set of eigenmode equations which describe the field line eigenfrequency, linear stability, and parallel eigenmode structure. We call these modes anisotropic Alfven-ballooning modes. The main results are: (1) The field line eigenfrequency can be significantly lowered by finite pressure effects. (2) The parallel mode structure of the transverse wave components is fairly insensitive to changes in the plasma pressure, but the compressional magnetic component can become highly peaked near the magnetic equator as a result of increased pressure, especially when P(sub perpendicular to) is greater than P(sub parallel) (here P(sub perpendicular to) and P(sub parallel) are the perpendicular and parallel plasma pressure). (3) For the isotropic (P(sub parallel) = P(sub perpendicular to) = P) case ballooning instability can occur when the ratio of the plasma presure to the magnetic pressure, beta = P/(B squared/8 pi), exceeds a critical value beta(sup B)(sub 0) is approximately equal to 3.5 at the equator. (4) Compared to the isotropic case the critical beta value is lowered by anisotropy, either due to decreased field line bending stabilization when P(sub parallel) is greater than P(sub perpendicular to) or due to increased ballooning-mirror destabilization when P(sub perpendicular to) is greater than P(sub parallel). (5) We use a beta-delta stability diagram to display the regions of instability with respect to the equatorial values of the parameters bar beta and delta, where bar beta = (1/3)(beta(sub parallel) + 2 beta(sub perpendicular to)) is an average beta value and delta = 1 - P(sub parallel)/P(sub perpendicular to) is a measure of the plasma anisotropy. The diagram is divided into regions corresponding to the firehose, mirror and ballooning instabilities. It appears that observed values of the plasma pressure are below the critical value for the isotropic ballooning instability but it may be possible to approach a ballooning-mirror instability when P(sub perpendicular to)/P(sub parallel) is greater than or approximately 2.

Chan, Anthony A.↗
DOE OSTI2025

Peeling-ballooning modes in spherical tokamaks: Multi-branch instabilities and effects beyond ideal MHD

A number of important physics effects on the stability of relatively high-n (n is the toroidal mode number) peeling-ballooning modes (PBMs) are investigated based on an equilibrium reconstructed from a NSTX discharge, utilizing extended magnetohydrodynamic (MHD) eigenvalue solvers. For a given toroidal mode number n, multiple branches of instabilities are computed, with the total number of unstable branches roughly linearly scaling with n. Most of the unstable branches are located in the plasma core region, but edge-localized branches, i.e., PBMs, are also identified at higher n-numbers. For the single-fluid-wise most unstable PBM with n = 19⁠, stabilizing/destabilizing effects due to various physics beyond ideal MHD are systematically investigated. Plasma toroidal flow is found to be weakly stabilizing. Local flow shear is generally stabilizing as well, with the degree of stabilization depending on the initial growth rate (without flow shear) of the mode. The plasma resistivity can strongly destabilize the PBM within the single-fluid framework. Anisotropic thermal transport, strong parallel sound wave damping, as well as two-fluid effects are all stabilizing to the mode. In particular, diamagnetic stabilization (within the two-fluid model) is found to be very strong for this mode.

Linear stability analysis↗
NASA NTRS1986

Resistive ballooning modes in line-tied coronal arcades

The equations describing the linear evolution of resistive ballooning modes are obtained by using a modified WKB expansion in the short perpendicular wavelength, while variations of the perturbations along the field are described by a slowly varying amplitude, on which the tying boundary conditions are imposed. In general, given an equilibrium, there are certain ranges of magnetic surfaces for which the system predicts instability even without dissipation. The main conclusion is that within the resistive MHD approximation cylindrically symmetric arcades with pressure falling with radius are unstable to resistive localized modes; the growth rates, close to ideal marginal stability, are large, so that it would appear that energy could be released during 10 to 100 Alfven times. The wavelength of the modes is expected to be limited by the ion gyroradius, when stabilizing drift effects must be taken into account. The nonlinear evolution of resistive ballooning modes should be studied to assess their overall relevance to the violent and rapidly evolving phenomena observed on the sun.

Velli, Marco↗
NASA NTRS1988

Current-driven resistive ballooning modes in axially bounded solar flare plasmas

The most unstable current-driven resistive modes of an axially bounded coronal loop are found in computer simulations to exhibit the spatial structure of ballooning modes. The observed modes are not confined to mode rational surfaces, but instead have broad radial extent. A theory assuming ballooning mode spatial structure predicts that a minimum current should be required for linear instability, and that, when the mode is unstable, the linear growth rate scales linearly with the resistivity eta below a critical resistivity, and scales as cu root of eta for larger resistivities. Both predictions are borne out by simulation results. Both theory and simulation analyses of the mode suggest that the strong radial structure of the mode near the ends of the system is the primary contributing factor to the instability of the mode. A helical current sheet is formed in the nonlinear evolution of the mode near the edge of the current channel and is accompanied by a strong radial gradient in the current and partial current reversal.

Otani, Niels F.↗
DOE OSTI2023

An adjoint-based method for optimising MHD equilibria against the infinite- n , ideal ballooning mode

We demonstrate a fast adjoint-based method to optimise tokamak and stellarator equilibria against a pressure-driven instability known as the infinite-n ideal ballooning mode. We present three finite-β (the ratio of thermal to magnetic pressure) equilibria: one tokamak equilibrium and two stellarator equilibria that are unstable against the ballooning mode. Using the self-adjoint property of ideal magnetohydrodynamics, we construct a technique to rapidly calculate the change in the eigenvalue, a measure of ideal ballooning instability. Using the SIMSOPT optimisation framework, we then implement our fast adjoint gradient-based optimiser to minimise the eigenvalue and find stable equilibria for each of the three originally unstable equilibria.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Two-stage crash process in resistive drift ballooning mode driven ELM crash

We report a two-stage crash process in edge localized mode (ELM) driven by resistive drift-ballooning modes (RDBMs) numerically simulated in a full annular torus domain with a scale-separated four-field reduced MHD (RMHD) model using the BOUT++ framework. In the early nonlinear phase, the small first crash is triggered by linearly unstable RDBMs, and m/n=2/1 magnetic islands are nonlinearly excited by nonlinear coupling of RDBMs as well as their higher harmonics. Here, m is the poloidal mode number, n is the toroidal mode number, the q = 2 rational surface exists near the pressure gradient peak, and q is the safety factor. Simultaneously, middle-n RDBM turbulence develops but is poloidally localized around X-points of the magnetic islands, leading to the small energy loss. The second large crash occurs in the late nonlinear phase. Higher harmonics of m/n=2/1 magnetic islands well develop around the q = 2 surface via nonlinear coupling and make the magnetic field stochastic by magnetic island overlapping. Turbulence heat transport develops at X-points of higher harmonics of m/n=2/1 magnetic islands, resulting in the turbulence spreading in the poloidal direction. The large second crash is triggered when the turbulence covers the whole poloidal region so that the magnetic island generation and magnetic field stochastization before the large crash can be interpreted as ELM precursors. It is concluded that the ELM trigger is attributed to the turbulent spreading in the poloidal direction in synchronization with the magnetic field stochastization and the crash is driven by E × B convection rather than the conventional Rechester–Rosenbluth anomalous electron heat transport.

Seto, H. (ORCID:0000000259278643)↗
DOE OSTI2021

Kinetic-ballooning-mode turbulence in low-average-magnetic-shear equilibria

In this work, kinetic-ballooning-mode (KBM) turbulence is studied via gyrokinetic flux-tube simulations in three magnetic equilibria that exhibit small average magnetic shear: the Helically Symmetric eXperiment (HSX), the helical-axis Heliotron-J and a circular tokamak geometry. For HSX, the onset of KBM being the dominant instability at low wavenumber occurs at a critical value of normalized plasma pressure $\beta ^{\rm KBM}_{\rm crit}$ that is an order of magnitude smaller than the magnetohydrodynamic (MHD) ballooning limit $\beta ^{\rm MHD}_{\rm crit}$ when a strong ion temperature gradient (ITG) is present. However, $\beta ^{\rm KBM}_{\rm crit}$ increases and approaches the MHD ballooning limit as the ITG tends to zero. For these configurations, $\beta ^{\rm KBM}_{\rm crit}$ also increases as the magnitude of the average magnetic shear increases, regardless of the sign of the normalized magnetic shear. Simulations of Heliotron-J and a circular axisymmetric geometry display behaviour similar to HSX with respect to $\beta ^{\rm KBM}_{\rm crit}$ . Despite large KBM growth rates at long wavelengths in HSX, saturation of KBM turbulence with $\beta > \beta _{\rm crit}^{\rm KBM}$ is achievable in HSX and results in lower heat transport relative to the electrostatic limit by a factor of roughly five. Nonlinear simulations also show that KBM transport dominates the dynamics when KBMs are destabilized linearly, even if KBM growth rates are subdominant to ITG growth rates.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Finite magnetic well effects on resistive and drift-resistive ballooning modes in a shaped tokamak

The impact of plasma shaping through magnetic well modifications on the stability of resistive ballooning modes (RBMs) in tokamaks is analysed, also including finite diamagnetic flows. Furthermore, various limiting cases of the dispersion relation, obtained by matching the ballooning equation across the ideal and resistive layers, are analysed. It is found that stability is generally improved by the combination of vertical elongation and positive triangularity, although, in some cases, the growth rate of the unstable mode can be enhanced by these effects. Usually, vertically elongated plasmas with no triangularity are prone to exhibit worse stability properties. A value for the critical β above which RBMs are driven unstable is identified, and a connection with type-III ELM activity is established.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

A study of resistive peeling–ballooning modes across spherical tokamaks

We investigate how non-ideal-magnetohydrodynamics (MHD) effects, in particular plasma resistivity, impact the peeling–ballooning stability thresholds in spherical tokamaks. This analysis follows the discovery of resistive kink-peeling modes in ELMing National Spherical Torus Experiment (NSTX) discharges. In the present study we extend this modeling to ELMing pulses in the Mega Ampere Spherical Tokamak (MAST) and MAST—Upgrade (MAST-U), where we find a clear resistive scaling for peeling–ballooning modes. While in NSTX ideal-MHD predicts stability for ELMing discharges, in MAST-U we find that the plasma is slightly unstable to peeling–ballooning modes, but is fully stabilized once diamagnetic effects are considered in terms of a growth rate normalization. A resistive power law scaling is calculated for these modes on MAST-U, which lies in between that of tearing modes and resistive interchange modes. A comparison between M3D-C1 and NIMROD shows reasonable agreement for this scaling. Resistivity destabilizes the modes and the peeling–ballooning unstable domain is considerably expanded in both, MAST and MAST-U. In addition to the MAST/-U pulses we also analyze resistive PB stability in a NSTX-similarity discharge on DIII-D. While having a different aspect ratio from NSTX, this discharge uses NSTX-like shaping parameters, toroidal field and plasma current. By considering these discharges alongside NSTX cases, we identify conditions influencing the onset of resistive peeling–ballooning modes. Furthermore, our findings indicate that magnetic shear in the pedestal region is closely linked to the emergence of resistive edge modes.

MAST-U↗
DOE OSTI2025

Data for "A study of resistive peeling-ballooning modes across spherical tokamaks"

The data in this repository correspond to the figures of the paper "A study of resistive peeling-ballooning modes across spherical tokamaks" published in the journal Plasma Physics and Controlled Fusion. The figures are created based on simulations with the M3D-C1 and NIMROD codes using Python post-processing tools.

edge localized modes↗
DOE OSTI2025

Global gyrokinetic simulations of kinetic-ballooning-mode turbulence in Wendelstein 7-X

We apply the global gyrokinetic code GENE-3D to perform kinetic-ballooning-mode (KBM) turbulence simulations in the Wendelstein 7-X (W7-X) stellarator using experimentally relevant parameters. In contrast to the flux-tube approach, we observe saturation of the turbulent fluctuations at finite amplitude. Analyzing the turbulent characteristics, we identify the presence of weakly driven KBM turbulence hybridizing with ion-temperature-gradient and trapped-electron-mode turbulence in the scenario under consideration, showing that it is possible that KBM activity can be driven in W7-X, opening up the path for studying this type of turbulence, which is highly relevant for future fusion power plants.

Electrostatics↗
DOE OSTI2023

Experimental Validation of a Kinetic Ballooning Mode in High-Performance High-Bootstrap Current Fraction Fusion Plasmas

We report the observation of a set of coherent high frequency electromagnetic fluctuations that leads to a turbulence induced self-regulating phenomenon in the DIII-D high bootstrap current fraction plasma. The fluctuations have frequency of 130~220kHz, the poloidal wave length and phase velocity are 16~30 m -1 and ~30 km/s, respectively in the outboard midplane with the estimated toroidal mode number n~5- 9. The fluctuations are located in the internal transport barrier (ITB) region at large radius and are experimentally validated to be kinetic ballooning modes (KBM). Furthermore, quasilinear estimation predicts the KBM to be able to drive experimental particle flux and non-negligible thermal flux, suggesting its significant role in regulating the ITB saturation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Nonlinear magnetohydrodynamic modeling of ideal ballooning modes in high- β Wendelstein 7-X plasmas

We present nonlinear magnetohydrodynamic (MHD) simulations of high- β Wendelstein 7-X plasmas using the stellarator extension of the M3D- C 1 code, building on the recent work that shows benign saturation of ideal ballooning modes above the designed β limit in the standard configuration [Zhou et al., Phys. Rev. Lett. 133, 135102 (2024)]. First, we examine the results' sensitivity to the parallel thermal conductivity. It is found that while an increased parallel conductivity reduces the linear growth rate, the saturated pressure profile is barely affected. Second, we consider the dependence on the profile shape. It is shown that an equilibrium with a peaked pressure profile and lower β is subject to more significant change than a broad profile with higher β and a larger growth rate, suggesting that benign saturation, or nonlinear stability, is not guaranteed and not dictated by linear growth. Third, we study the influence of the magnetic configuration, with the equilibrium rotational transform varied by adjusting the planar coil current. With similar growth rates, similar magnitudes of profile change are found regardless of the presence of a low-order resonance, which implies that the saturation mechanism is not specific to a resonant or non-resonant mode. These results indicate that MHD stability should still be treated seriously in stellarator operation and design, for which nonlinear modeling using tools like M3D- C 1 can play an instrumental role.

Zhou, Yao [Shanghai Jiao Tong University (China)] ↗
NASA NTRS1989

The effect of ballooning modes on thermal transport and magnetic field diffusion in the solar corona

Presently favored mechanisms of coronal heating (current sheet dissipation and Alfven wave resonant heating) deposit heat in thin layers. Classical thermal conduction cannot explain how heat is transported across the magnetic field. If heating occurs in thin layers, large pressure gradients can be created which can give rise to ballooning modes. These instabilities are caused by the pressure gradient and the curvature of the magnetic field, and are stabilized by magnetic tension. The modes are broad band in wavelength and should produce turbulence. A mixing length expression for the turbulent heat transport shows that it is more than adequate to rapidly convect heat into much broader layers. Furthermore, the turbulent resistivity implies that heating occurs over most of the width of these broadened layers. The broadening also implies that much shorter time scales are required for heating. The beta values in the corona suggest that 1-10 turbulent layers are formed in typical loop or arch structures.

Strauss, H. R.↗
DOE OSTI2026

Impact of impurities on peeling–ballooning modes and turbulence in tokamak plasmas

This study investigates the impact of various impurity species on peeling–ballooning (PB) modes and microturbulence in tokamak plasmas through the extension of traditional two-fluid and gyro-landau-fluid (GLF) models. By incorporating finite Larmor radius (FLR) effects, the analysis provides a comprehensive understanding of impurity-driven impact and its interaction with plasma turbulence. Depending on charge state and local plasma conditions, heavy impurities may exhibit gyro-radii larger than those of main ions, which are captured in the extended GLF model presented. Following the presentation of modified two-fluid equations incorporating impurity effects, we systematically analyze the distinctions between impurity and main ion dynamics and their resultant feedback mechanisms on plasma behavior. Derivation of the linear dispersion relation enables quantification of impurity-mediated modifications to: plasma vorticity, diamagnetic drift and gyroviscous effects, electron Hall physics, and FLR effects. BOUT++ – based linear simulations corroborate this formalism, demonstrating systematic stabilization of PB modes upon impurity seeding. And then operational implications for practical impurity control strategies in tokamak devices are proposed. The results underscore the necessity of impurity management to maintain stability and optimize plasma confinement, with specific focus on how FLR effects contribute to transport dynamics. This work paves the way for enhanced modeling and simulation efforts, supporting the development of strategies to control impurity-induced turbulence and improve overall reactor performance.

BOUT++ simulation↗