SEARCH · Search NASA

Results for “batch simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Online and Offline Identification of False Data Injection Attacks in Battery Sensors Using a Single Particle Model

The cells in battery energy storage systems are monitored, protected, and controlled by battery management systems whose sensors are susceptible to cyberattacks. False data injection attacks (FDIAs) targeting batteries’ voltage sensors affect cell protection functions and the estimation of critical battery states like the state of charge (SoC). Inaccurate SoC estimation could result in battery overcharging and over discharging, which can have disastrous consequences on grid operations. This paper proposes a three-pronged online and offline method to detect, identify, and classify FDIAs corrupting the voltage sensors of a battery stack. To accurately model the dynamics of the series-connected cells a single particle model is used and to estimate the SoC, the unscented Kalman filter is employed. FDIA detection, identification, and classification was accomplished using a tuned cumulative sum (CUSUM) algorithm, which was compared with a baseline method, the chi-squared error detector. Online simulations and offline batch simulations were performed to determine the effectiveness of the proposed approach. Throughout the batch simulations, the CUSUM algorithm detected attacks, with no false positives, in 99.83% of cases, identified the corrupted sensor in 97% of cases, and determined if the attack was positively or negatively biased in 97% of cases.

25 ENERGY STORAGE↗

DOE OSTI2022

Organomercury Measurements from Sludge Batch 10 Simulant Studies

Researchers at the Savannah River National Laboratory have recently performed testing to evaluate the Sludge Batch 10 flowsheet using simulated sludge waste. In the course of this testing several samples were taken to determine the concentration of organomercury species resulting from sludge batch processing. These samples were submitted to the Savannah River National Laboratory Sensing and Metrology department quantitation using a mercury analyzer. The signal amplifier used to perform organomercury quantitation in the mercury analyzer experienced a malfunction in the course of analysis, leading to uncertainty of organomercury concentrations observed. Seventy-three organomercury samples from six project submissions to the Savannah River National Laboratory Sensing and Metrology department have been critically reviewed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

GridSTAGE (aka PowerDrone)

Simulation tool for electrical grid security. It is possible to select from pre-loaded power system topologies, enable different grid controls (like AGC, power system stabilizer), add faults, tweak different parameters, add pre-modeled attack scenarios, and run batch simulations to generate data needed for research.

Nandanoori, Sai Pushpak↗

DOE OSTI2020

Cesium Removal Performance Comparisons of Crystalline Silicotitanate Media Batches with Savannah River Site Waste Simulant

The Tank Closure Cesium Removal (TCCR) system uses ion exchange columns filled with Crystalline Silicotitanate (CST) media to process radioactive waste solutions for the removal of Cs137. TCCR currently focuses on dissolving Savannah River Site (SRS) Tank 10H waste (primarily sodium salt cake solids) within the tank followed by at-tank ion exchange column treatment. Plans are underway to prepare and install a second TCCR unit at SRS. Capacity and particle size differences exist between archived (IE-911) and more recently-prepared CST media batches (9120- B and 9140-B). Side-by-side comparison testing was performed to evaluate the cesium removal performance of each batch to aid in selecting the preferred CST batch and media characteristics to load into the second TCCR unit. Batch contact equilibrium and flow-through column tests have been conducted with three CST batches using an SRS Average Simulant. Simulant batch contact equilibrium cesium loading results for the three CST batches (including two lots of one batch) are provided in Table ES-1. The 35 °C data indicates that the archived IE-911 batch has a higher cesium capacity than recently-prepared CST media and that the minor TCCR CST 9120-B media lot (2099000035) has similar cesium removal performance to the major TCCR lot (2099000034). Tests conducted at 25 ºC for the archived IE-911 CST batch indicated lower cesium removal performance with this simulant batch than was observed recently with a different SRS Average Simulant batch. A dilution factor (DF) is typically utilized when modeling engineered CST media cesium loading performance to account for mass contributions from the binder material. In cases where CST performance is lower than expected, this factor includes corrections for the binder and for low performance. The ZAM (Zheng, Anthony, and Miller) Isotherm Model DF values are provided in Table ES-1 for each simulant batch contact result. DF values near 0.5 were determined for the 9120-B and 9140-B CST batch contact tests while DF values near 0.6 (20% higher) were determined for the tests with IE-911. These dilution factors are lower than recently observed with a different SRS Average Simulant batch (9140-B DF = 0.68; IE-911 DF = 1.0). Based on these results, it appears that some component in the simulant solution used for equilibrium testing may have resulted in reduced cesium loading on the CST media.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2023

Modeling of Chemical Slurry Rheology in DWPF Sludge Batch (SB) 10 Simulants

The Defense Waste Processing Facility (DWPF) treats high-activity radionuclides from sludge through a process called vitrification. This process converts radioactive liquid waste currently stored in tank farms into a solid glass form that is suitable for long-term storage and disposal. Due to the complexities involved in vitrifying this waste within each operation of the Chemical Processing Cell (CPC), waste rheology is studied to characterize the fluid-mechanical properties as it passes through the CPC and into the Melter. To better understand the waste and validate flow behavior, slurry rheology of simulants that represents the waste was studied at various acid stoichiometry percentages and solids concentrations to determine the simulant’s yield stress and viscosity. This research work has been supported by the DOE-FIU Science & Technology Workforce Development Initiative, an innovative program developed by the U.S. Department of Energy’s Office of Environmental Management (DOE-EM) and Florida International University’s Applied Research Center (FIU-ARC). During the spring of 2022, a DOE Fellow intern, Brendon Cintas, spent 10 weeks doing a summer internship at Savannah River National Laboratory (SRS) under the supervision and guidance of Dan Lambert, Chemical Flowsheet Development. The intern’s project was initiated on June 6, 2022, and continued through August 11, 2022 with the objective of assisting scientists at SRNL’s Rheology and Grout Laboratory at Aiken Country Technology Lab (ACTL) better understand the sludge composition on the rheology of a simulant slurry using a HAAKE RheoStress 6000 rheometer and extrapolate the results to the real-waste data.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2024

Low Purge and Mercury Recovery Testing with Sludge Batch 10 Tank 40 Simulant

Researchers at the Savannah River National Laboratory (SRNL) have completed testing as requested by Savannah River Mission Completion (SRMC) to perform experiments to determine the impact of using a lower or inert purge in Sludge Batch (SB) 10 processing under the Nitric-Glycolic Acid (NGA) flowsheet. A key objective of this testing was also to determine the mercury speciation and recovery during each experiment. The testing was performed as part of the SB10 Technical Task Request (TTR) and Task Technical and Quality Assurance Plan (TTQAP). Two sets of tests were performed, and a Run Plan was approved prior to each set of experiments to document the planned testing. Three initial experiments were completed to determine whether a low air purge would be beneficial to CPC processing at higher acid stoichiometry (110%) based on the Koopman minimum acid (KMA) equation (116% Hsu). One of the tests, an inert nitrogen purge experiment, was also completed to demonstrate that excluding oxygen did not introduce any new hazards. The experiments were designed to be identical except for the change in purge gas and purge flowrate from run to run. After reviewing the results from the initial three experiments, six additional tests were proposed by SRNL to support the lower purge study and to look for processing alternatives for improving mercury recovery. These additional six tests were all completed at a very low acid stoichiometry to mimic the pH experienced during processing in DWPF (~7). DWPF is processing SB10 sludge at an acid stoichiometry of 90% based on the Hsu equation. The additional SRNL experiments were performed at an acid stoichiometry of 62.5% KMA stoichiometry (66.3% Hsu) to produce a Sludge Receipt and Adjustment Tank (SRAT) product with a pH of about 7. All experiments used simulants of both SWPF streams, although no entrained solvent was added during any of the experiments

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2024

Mercury Testing with Sludge Batch 10 Tank 40 Simulant

Savannah River Mission Completion (SRMC) requested that researchers at Savannah River National Laboratory (SRNL) perform testing designed to examine why the Defense Waste Processing Facility (DWPF) is not collecting elemental mercury in the Mercury Water Wash Tank (MWWT). In order for DWPF to recover mercury, mercuric oxide must first be reduced to elemental mercury. The elemental mercury must then be steam stripped, condense, and coalesce in the Mercury Water Wash Tank (MWWT) during chemical processing in the Sludge Receipt and Adjustment Tank (SRAT). The efficiency of these steps was investigated in a series of laboratory scale SRAT experiments under the nitric-glycolic and nitric-formic flowsheets utilizing Momentive Y-17112 and Antifoam 747. Mercury speciation in the Slurry Mix Evaporator Condensate Tank (SMECT) and condensate streams was also examined. The key conclusions from these experiments are as follows: Mercury II Oxide may not be fully reduced to elemental mercury during acid addition at 93°C. Higher temperatures, i.e., boiling may be necessary to fully reduce Mercury II Oxide. The highest percent mercury recovery (71 %) in the MWWT was observed in the MS-NGA-17112 experiment (nitric-glycolic acid flowsheet with Momentive Y-17112), which is how DWPF is currently operating the SRAT.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Removal of High Specific Activity Fission Products from Uranyl Sulfate Waste Solutions

The Savannah River National Laboratory (SRNL) is currently providing support to SHINE Medical Technologies (SHINE) which plans to deploy a low energy, accelerator-based neutron source to fission low enriched U in a uranyl sulfate target solution for 99 Mo production. The 99 Mo is initially separated from the fission products and target solution by an extraction column. Subsequent washing of the column will generate waste solutions containing residual U and fission product activity. A small number of high specific activity fission products (e.g., 90 Sr, 137 Cs, and 144 Ce) in these streams will likely control the classification of the low level waste (LLW). If a sufficient amount of the high specific activity isotopes are separated from the SHINE waste streams and concentrated into a waste form, it would be possible to treat a majority of the wash solutions from the column operations as a lower class of LLW (Class A versus Class B or C or Class B versus Class C). The high specific activity fission product elements could then be dispositioned as a much smaller volume of waste rather than requiring the disposal of the entire waste stream at the higher waste classification. The Savannah River Site (SRS) has experience with using monosodium titanate (MST) and crystalline silicotitanate (CST) to remove Cs and Sr from high salt content waste solutions generated during the reprocessing of nuclear fuels and targets. Both of these materials have worked very well for their intended purposes at the SRS where the fission product elements are removed from highly alkaline waste. On the other hand, SHINE waste streams from the extraction column contain H 2 SO 4 which makes the solution acidic. Additionally, the SRS waste streams do not contain other fission product elements such as transition metals or lanthanides because they precipitate upon neutralization of the SRS waste and are not present in the supernate which is dispositioned as LLW following treatment. As such, there are inherent differences between SHINE and SRS waste treatment strategies. Savannah River National Laboratory was tasked with performing scoping studies to see if MST and CST would remove Sr, Cs, and Ce from an acidic mixed metal simulant solution. Batch contact experiments were performed using MST and two CST type materials. The MST material is a 15 wt % powder in 0.15 M NaOH slurry. The MST showed low adsorption for elements of interest from acidic solution. Furthermore, the powder size makes MST non-ideal for column operations. A CST IE-911 ion exchange material had high Cs adsorption, moderate Sr, and marginal Ce adsorption. Based on adsorption of all species, the ion exchange capacity was found to be 0.032 meq/mL. A bench-top column experiment to measure elemental breakthrough curves was performed using CST IE-911 where chromatographic separations of the mixed simulant were expected to occur. While most elements behaved as expected, the lanthanide series, containing Ce, broke though the column earlier than expected. The second CST material, CST R9120, displayed high adsorption for all elements in the acidic mixed simulant solutions in a batch contact study, and had a calculated loading capacity of 0.091 meq/mL. Future studies to develop a waste treatment flowsheet should focus on CST R9120 to treat SHINE waste solutions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Simulation of DWPF Chemical Process Cell Using a Reaction Calorimeter

The Defense Waste Processing Facility (DWPF) converts liquid radioactive waste into glass using a Sludge Receipt Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) in addition to other processes. The SRAT and SME processes can be simulated on a small-scale using the Mettler-Toledo Reaction Calorimeter (RC1). This equipment is able to automate the execution and monitoring of experiments involving nonradioactive chemical simulants. During the chemical processing of sludge in the SRAT process, foam begins to form and can foam over the reaction vessel. The current antifoam used at DWPF creates a risk of increased flammability and has a limited pH range. Usually, mercury is circulated back into the reaction vessel during the SRAT process, making it difficult to remove. To combat foam over, novel antifoams will be tested during the boil-up process using the RC1. To improve mercury extraction, 3D-printed coalescer columns will be tested within the Mercury Water Wash Tank (MWWT) of the RC1. Testing of Simulant Sludge Batch 6 (SB6) was performed to ensure: the sludge would form a stable foam at boiling during full SRAT/SME runs; the antifoam would reduce the amount of foam within the vessel The sludge and a Precipitate Reactor Feed Tank (PRFT) simulant with monosodium titanate (MST) were mixed separately, combined, and then heated to boiling. As shown below, the antifoam used was able to eliminate the foam within the vessel, as expected. The FormLabs Form2 3D Printer can be used to create roughly 3-inch tall and 1-inch diameter columns from clear and ceramic resins. The columns will utilize chemical and physical forces to draw the mercury out of a condensed offgas stream leaving the RC1 reaction vessel. These columns will be tested during full SRAT/SME runs on the basis of how well they are able to collect elemental mercury. In preparation for full-scale runs, the RC1 equipment was assembled onto a custom table and tested with water runs. The software used to control automation, iControl, has a user-friendly interface that allows the experiment to be altered as needed. An example of the data recorded during an experimental run is represented in Figure 1 below. Water runs were utilized as a way to prove if the RC1 system was functioning in the following areas: Boil-up rates, Chemical additions using pumps, Temperature readings, Balance readings, Probe readings, Offgas system, Agitation. Future Plans: Five novel antifoams will be tested during full SRAT/SME runs. The most effective antifoam will be utilized in DWPF's Chemical Process Cell. The design of the Mercury Extraction Coalescer can be further manipulated to increase the extraction of not only elemental mercury, but other heavy metals in environmental remediation processes as well.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Process design tools and techno-economic analysis for capacitive deionization

Capacitive deionization (CDI) devices use cyclical electrosorption on porous electrode surfaces to achieve water desalination. Process modeling and design of CDI systems requires accurate treatment of the coupling among input electrical forcing, input flow rates, and system responses including salt removal dynamics, water recovery, energy storage, and dissipation. Techno-economic analyses of CDI further require a method to calculate and compare between a produced commodity (e.g. desalted water) versus capital and operational costs of the system. In this work, we demonstrate a new modeling and analysis tool for CDI developed as an installable Matlab program that allows direct numerical simulation of CDI dynamics and calculation of key performance and cost parameters. The program is provided for free and is used to run open-source Simulink models. The Simulink environment sends information to the program and allows for a drag and drop design space where users can connect CDI cells to relevant periphery blocks such as grid energy, battery, solar panel, waste disposal, and maintenance/labor cost streams. The program allows for simulation of arbitrary current forcing and arbitrary flow rate forcing of one or more CDI cells. We employ validated well-mixed reactor formulations together with a non-linear circuit model formulation that can accommodate a variety of electric double layer sub-models (e.g. for charge efficiency). The program includes a graphical user interface (GUI) to specify CDI plant parameters, specify operating conditions, run individual tests or parameter batch-mode simulations, and plot relevant results. The techno-economic models convert among dimensional streams of species (e.g. feed, desalted water, and brine), energy, and cost and enable a variety of economic estimates including levelized water costs.

42 ENGINEERING↗

DOE OSTI2026

Chemical and Radiological Compatibility Testing of 3D Printed Materials

To dramatically increase the adaptability, performance, and safety of processes in support of the Defense Waste Processing Facility (DWPF), Savannah River National Lab (SRNL) plans to perform chemical and radiological compatibility testing on a wide variety of 3D printed materials of interest. The 3D printing process provides numerous strategic operational benefits such as rapid prototyping of complex designs and geometry specific to the needs of the nuclear waste disposition process, as well as on-demand rapid prototyping and iteration with materials that aren’t as accessible through traditional manufacturing methods. Reaction chemistry in simulated waste batches can be matched closely to its radioactive counterpart, but glass reactor vessels have limitations. Vessel geometry can play a big factor in mixing transport limitations, process chemistry, and degradation reaction kinetics. In addition, additive manufacturing allows for much more detailed vessel design than traditional alternatives. Waste processing techniques in DWPF also encounter extreme chemical environments including high pH, strong acids, abrasive slurries, and significant irradiation. To meet these challenges, a matrix of various polymer, ceramic, and metal additive manufacturing materials have been exposed to a suite of chemical environments of interest as well as radioactive dose (such as gamma radiation from 60 Co) to properly test their durability under these conditions. Mass change has been monitored over a period of up to a week in these conditions, as well as added characterization for surface modification through Scanning Electron Microscopy/Electron Dispersive X-ray analysis (SEM/EDX). Further chemical characterization has been monitored through Fourier-Transform InfraRed Spectroscopy (FTIR), with planned investigation via thermal and tensile strength degradation. While the direct product of this research is identification of material(s) that can withstand specific hazardous environments encountered by the mercury water wash tank in DWPF process simulation experiments, the reference base of materials will be used for many other nuclear processes in the pursuit of rapidly developed, cost-efficient, and highly specific devices for environmental remediation and much more.

Wilson, Nathan W. [Savannah River National Laborat↗

DOE OSTI2021

Application of spectroscopic evidence to diffuse layer model (DLM) parameter estimation for cation adsorption onto ferrihydrite in single- and bi-solute systems

The diffuse layer model (DLM) is one of the most frequently used surface complexation models (SCM) for predicting cation adsorption onto ferrihydrite. However, the DLM with its existing database sometimes fails to predict cation adsorption, especially in multi-solute systems. Notably, the failure is often attributed to inaccurate selection of the surface complexes and/or underestimation of the site density for DLM formulation. DLM simulations of batch adsorption data conducted with cadmium, copper, lead, and zinc on ferrihydrite in CO2 free systems demonstrates the ability of the DLM to fit single-solute data reasonably well but highlights its limitations with respect to predicting bi-solute data. Modifications to the DLM were made in two steps. First, spectroscopic evidence was used to guide cation complexation reactions at the ferrihydrite surface. Second, surface characteristics (reactive site density, specific surface area, and acidity constants) of ferrihydrite were updated according to recent literature. The results from this study suggest that when spectroscopic verification is employed and surface site density is increased, a simple two-site DLM can predict cation adsorption on ferrihydrite in single-solute systems for pH data above 3.5 and in most of the bi-solute systems tested.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Thermal and solubility effects on fault leakage during geologic carbon storage

Geologic carbon storage (GCS) is a promising method for reducing anthropogenic CO 2 emissions to the atmosphere. To safely deploy GCS in the field, it is necessary to assess risks and the effect of uncertainty on safe storage. The effect of uncertainty can be quantified using batches of simulations, but the high computational costs of high-resolution simulations necessitate use of reduced-order models (ROMs). Previous work involves ROMs for quantifying the risk of different potential leakage paths from storage reservoirs to shallow formations. However, previous studies on development of fault-leakage ROMs have limited numbers of uncertain parameters and do not explicitly examine impacts of CO 2 solubility and thermal stresses on fault reactivation, which can generate high-permeability pathways and compromise CO 2 storage. Here, we analyze an ensemble of simulations considering CO 2 leakage from a storage reservoir to a shallow aquifer through a fault while varying a number of uncertain parameters related to thermo-hydro-mechanical properties and CO 2 injection. We show the effects of solubility on: free-phase CO 2 -leakage rates, brine-leakage rates, and poroelastic fault destabilization. We find that CO 2 solubility is more important for estimating free-phase CO 2 -leakage rates compared to brine-leakage rates or poroelastic fault destabilization. We also find that thermal stresses and overpressures have different spatial distributions within the fault, indicating that the spatial variability of overpressures due to variation in flow parameters does not necessarily make the spatial variability of thermal stresses negligible. We suggest the use of the CO 2 phase-change path as a variable in future fault-leakage ROMs.

03 NATURAL GAS↗

DOE OSTI2020

Impact of Cr and Co on 99Tc retention in magnetite: A combined study of ab initio molecular dynamics and experiments

This work explores the effect of co-mingled dopants, Co(II) and Cr(III), on Tc(IV) incorporation and retention in magnetite when heat treated to 625 or 700 °C. Key trends in Tc retention in the high temperature regime were identified using a combination of density-functional-theory based ab initio molecular dynamics (AIMD) simulations, and batch experiments including solid phase characterization techniques, e.g. X-ray absorption spectroscopy. A stabilizing effect on Tc(IV) was observed when the number of Tc and Cr atoms are equal or when the magnetite surface is oversaturated with Tc and Cr inclusions. Here, oversaturation is hypothesized to force Cr from the magnetite surface to form a Cr2O3 phase, which may act as a protective layer that prevents Tc release. With the addition of Co, Tc(IV) is stabilized via redox processes. The presence of Cr in low concentrations interferes with this redox stabilization and Cr is preferentially stabilized as opposed to Tc. As a result, using Co as a stabilizing dopant for Tc may be compromised in the presence of Cr. When the relative concentration of Tc, Cr and Co is the same, or more Co atoms are added to high Cr incorporated systems, the formation of the Cr2O3 phase may be suppressed. Although waste streams with co-mingled Tc and Cr potentially may benefit from a Co dopant, since the formation of a Cr2O3 passivation layer may protect incorporated Tc from being released, the relative concentration of the three elements will be a critical parameter for maximizing effectiveness of this strategy.

Lee, Mal Soon↗

DOE OSTI2020

Cesium Removal Performance Comparisons of Crystalline Silicotitanate Media Batches with Savannah River Site Waste Simulant

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

CoSim: A Simulator for Co-Scheduling of Batch and On-Demand Jobs in HPC Datacenters

The increasing scale and complexity of scientific applications are rapidly transforming the ecosystem of tools, methods, and workflows adopted by the high-performance computing (HPC) community. Big data analytics and deep learning are gaining traction as essential components in this ecosystem in a variety of scenarios, such as, steering of experimental instruments , acceleration of high-fidelity simulations through surrogate computations, and guided ensemble searches. In this context, the batch job model traditionally adopted by the supercomputing in-frastructures needs to be complemented with support to schedule opportunistic on-demand analytics jobs, leading to the problem of efficient preemption of batch jobs with minimum loss of progress. In this paper, we design and implement a simulator, CoSim, that enables on-the-fly analysis of the trade-offs arising between delaying the start of opportunistic on-demand jobs, which leads to longer analytics latency, and loss of progress due to preemption of batch jobs, which is necessary to make room for on-demand jobs. To this end, we propose an algorithm based on dynamic programming with predictable performance and scalability that enables supercomputing infrastructure schedulers to analyze the aforementioned trade-off and take decisions in near real-time. Compared with other state-of-art approaches using traces of the Theta pre-Exascale machine, our approach is capable of finding the optimal solution, while achieving high performance and scalability.

batch job preemption↗

DOE OSTI2024

SuperNu Version 4.x

We seek to release SuperNu, Version 4.x, as a continuation of development for the open source SuperNu software. The SuperNu, Version 3.x Monte Carlo radiative transfer code for astrophysical transients was released with GPLv3 copyright, asserted by LANL in 2015. For the next release we have features planned for development , including: opacity implementation (including non-local thermodynamic equilibrium effects), generalized source implementation (e.g. for emulating shock heating in Type II supernovae), 3T (electron, ion, radiation) internal energy update, special relativity corrections through O(v^2/c^2), light polarization (e.g. for comparison to spectroplarimetry observations of supernovae and kilonovae), and infrastructure features (checkpoint and restart of simulations, and tools including setup and Slurm batch scripts and simulation post-processing/analysis scripts). These features are intended to improve the fidelity and/or better understand uncertainty in supernova and kilonova light curve calculations.

Wollaeger, Ryan↗

DOE OSTI2021

In-situ X-ray and visual observation of foam morphology and behavior at the batch-melt interface during melting of simulated waste glass

We report to attain a basic understanding of the primary foam structure and behavior, which affects the heat and mass transfer and the efficiency of the glass melting process, we investigated the primary foam layer under the glass batch floating on molten glass. The primary foam affects mass transfer during batch melting, in turn affecting the melting process. The recently performed direct in-situ three-dimensional X-ray computed tomography of the batch melting in a laboratory-scale melter vessel allowed us to visualize the features of the reacting batch layer and the foam that develops at its bottom, though with an insufficient resolution of images. In this study, we obtained better temporal and spatial resolution using the two-dimensional X-ray radiography and visual observation of the structure and behavior of transient primary foam as it formed and decayed. As soon as the batch was charged onto the melt surface, foam bubbles began to evolve, grow, and coalesce, forming a primary foam layer, 5-10 mm thick, within tens of seconds. This foam layer was sustained by ongoing gas evolving reactions counterbalanced by bubble coalescence into cavities that moved sideways and escaped to the atmosphere. Eventually, the entire remaining batch turned into foam that gradually decayed at the melt surface. The decay rate agreed with literature observations of surface foam produced by secondary foaming.

36 MATERIALS SCIENCE↗