Heat generation in sealed batteries.
Analytical method predicting heat generation in sealed batteries, noting overcharge ratio effects
Gross, S.↗
SEARCH · Search NASA
Results for “battery heat generation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Thermal management challenges in lithium-ion batteries: understanding heat generation mechanisms
This paper investigates heat generation in commercial 18 650 lithium-ion battery cells and the thermal management challenges from their high energy density and electrochemical processes. Thermal effects can degrade performance, accelerate aging, and increase thermal runaway risk. Using isothermal calorimetry and EIS, the study emphasizes optimizing thermal behavior to improve battery efficiency, safety, and durability.
25 ENERGY STORAGE↗
Heat Generation versus Heat Dissipation Maps for Batteries (Battery Safety Maps) [SWR-21-27]
NREL's Battery Safety Map (Heat Generation versus Heat Dissipation Maps for Batteries) generates a response surface that is grouped into regions where the battery is deemed safe from the propagation of thermal runaway, those where an engineering solution would render the battery safe, and finally instances where thermal runaway is inevitable. The demarcation for the different regions is provided by specifications or constraints imposed by the end user. NREL's Battery Safety Map is a user-defined subroutine that sweeps through a set of parameters describing the operating conditions and short-circuit scenarios for battery safety simulations. For each run, the electrochemical-thermal model implementing reaction kinetics and gas generation are run to evaluate the amount of heat generated. A thermal model then captures the amount of heat dissipation based on boundary conditions defined (e.g., forced convection, constant temperature at the surface, etc.). Based on the rate of heat transfer and the amount of heat generated, each run is classified into "safe," "mitigation possible," or "unsafe" zones. These categories are defined based on constraints or tolerance specifications provided by the end user.
Santhanagopalan, Shriram↗
Heat generation in sealed batteries.
Calorimetric methods for battery and cells testing, discussing heat generation data correlation
Gross, S.↗
Iron-Doped Sodium Vanadium Oxyflurophosphate Cathodes for Sodium-Ion Batteries—Electrochemical Characterization and In Situ Measurements of Heat Generation
Sodium-ion batteries (NaIBs) are increasingly being envisioned for grid-scale energy-storage systems because of cost advantages. However, implementation of this vision has been challenged by the low-energy densities delivered by most NaIB cathodes. Toward addressing this challenge, the authors report the synthesis and characterization of a new iron-doped Na 3 Fe 0.3 V 1.7 O(PO 4 ) 2 F 2 cathode using a novel facile hydrothermal route. The synthesized material was characterized using scanning electron microscopy, X-ray diffraction, and Mössbauer spectroscopy techniques. The obtained discharge capacity in the half-cell configuration lies from 119 to 125 to 130 mA h/g at C/10 while tested using three different electrolyte formulations, dimethyl carbonate–ethylene carbonate (EC)–propylene carbonate (PC), diethyl carbonate–EC, and EC–PC, respectively. The synthesized cathodes were also evaluated in full-cell configurations, which delivered an initial discharge capacity of 80 mA h/g with NaTi 2 (PO 4 ) 3 MWCNT as the anode. Ionic diffusivity and interfacial charge transfer kinetics were also evaluated as a function of temperature and sodium concentration, which revealed that electrochemical rate performances in this material were limited by charge-transfer kinetics. To understand the heat generation mechanism of the Na/Na 3 Fe 0.3 V 1.7 O(PO 4 ) 2 F 2 half-cell during charge and discharge processes, an electrochemical isothermal calorimetry measurement was carried out at different current rates for two different temperatures (25 and 45 °C). The results showed that the amount of heat generated was strongly affected by the operating charge/discharge state, C-rate, and temperature. Altogether, this work provides a new synthesis route for the development of iron-doped Na 3 Fe 0.3 V 1.7 O(PO 4 ) 2 F 2 -based high-performance sodium cathode materials aimed at providing a viable pathway for the development and deployment of large-scale energy-storage based on sodium battery systems.
25 ENERGY STORAGE↗
Passive Mitigation of Cascading Propagation in Multi-Cell Lithium Ion Batteries
The heat generated during a single cell failure within a high energy battery system can force adjacent cells into thermal runaway, creating a cascading propagation effect through the entire system. This work examines the response of modules of stacked pouch cells after thermal runaway is induced in a single cell. The prevention of cascading propagation is explored on cells with reduced states of charge and stacks with metal plates between cells. Reduced states of charge and metal plates both reduce the energy stored relative to the heat capacity, and the results show how cascading propagation may be slowed and mitigated as this varies. These propagation limits are correlated with the stored energy density. Results show significant delays between thermal runaway in adjacent cells, which are analyzed to determine intercell contact resistances and to assess how much heat energy is transmitted to cells before they undergo thermal runaway. A propagating failure of even a small pack may stretch over several minutes including delays as each cell is heated to the point of thermal runaway. This delay is described with two new parameters in the form of gap-crossing and cell-crossing time to grade the propensity of propagation from cell to cell.
25 ENERGY STORAGE↗
Special Test Methods for Batteries
Various methods are described for measuring heat generation in primary and secondary batteries as well as the specific heat of batteries and cell thermal conductance. Problems associated with determining heat generation in large batteries are examined. Special attention is given to monitoring temperature gradients in nickel cadmium cells, the use of auxiliary electrodes for conducting tests on battery charge control, evaluating the linear sweep of current from charge to discharge, and determining zero current voltage. The fast transient behavior of batteries in the microsecond range, and the electrical conductance of nickel sinters in the thickness direction are also considered. Mechanical problems experienced in the vibration of Ni-Cd batteries and tests to simulate cyclic fatigue of the steel table connecting the plates to the comb are considered. Methods of defining the distribution of forces when cells are compressed during battery packaging are also explored.
Gross, S.↗
A review of thermal physics and management inside lithium-ion batteries for high energy density and fast charging
Traditionally it has been assumed that battery thermal management systems should be designed to maintain the battery temperature around room temperature. That is not always true as lithium-ion battery (LIB) R&D is pivoting towards the development of high energy density and fast charging batteries. Therefore, it is necessary to have a comprehensive review of thermal considerations for LIBs targeted for high energy density and fast charging, i.e., the optimal thermal condition, thermal physics (heat transport and generation) inside the battery, and thermal management strategies. As the energy density and charge rate increases, the optimal battery temperature can shift to be higher than room temperature. In the first part of the review various sources of heat generation inside LIBs and various approaches to minimizing battery heat generation are summarized. The importance of heat of mixing due to ion diffusion during fast charging is also highlighted. To improve the temperature uniformity and avoid excessive internal temperature rise, heat transfer inside the battery needs to be enhanced, and reducing the thermal contact resistance between the electrodes and separator can significantly increase the effective thermal conductivity of batteries. In the second part of the review various challenges and latest developments related to thermal transport and properties of LIBs are discussed. Finally, a summary of latest advancement on smart control of internal temperature of LIBs is discussed as depending on the ambient temperature and the optimal temperature; the battery heat needs to be retained or dissipated to elevate or avoid temperature rise.
25 ENERGY STORAGE↗
Practical Battery Thermal Modeling Techniques
Lithium-ion batteries are thermo-electrochemical devices, whereby nearly every facet of their functionality and performance are thermally driven. As a result, it is important to have thermal modeling techniques that effectively capture the intricacies of both the electrochemical nature of the battery and also the complex thermal network that typically results from the design of the battery thermal management system. Here we present a thermal modeling workflow and a set of general assumptions for how to construct a thermal model of a Li-ion battery pack. We use a 14-cell bank of 18650-format Li-ion cells, loosely based on a proposed alternative battery design for Orion, as the example. Although the workflow is performed with Thermal Desktop and related utilities, the focus of this presentation is less about software specific techniques, but rather is focused on the assumptions and conditions that should be used in a model (regardless of the tool used to build the model). Example cases and results will be presented for charge, discharge, and thermal runaway.
lithium-ion battery↗
NASA 50 amp hour nickel cadmium battery waste heat determination
A process for determining the waste heat generated in a 50-ampere-hour, nickel cadmium battery as a function of the discharge rate is described and results are discussed. The technique involved is essentially calibration of the battery as a heat transfer rate calorimeter. The tests are run at three different levels of battery activity, one at 40-watts of waste heat generated, one at 60, and one at 100. Battery inefficiency ranges from 14 to 18 percent at discharge rates of 284 to 588 watts, respectively and top-of-cell temperatures of 20 C.
Mueller, V. C.↗
High efficiency low cost monolithic module for SARSAT distress beacons
The program objectives were to develop a highly efficient, low cost RF module for SARSAT beacons; achieve significantly lower battery current drain, amount of heat generated, and size of battery required; utilize MMIC technology to improve efficiency, reliability, packaging, and cost; and provide a technology database for GaAs based UHF RF circuit architectures. Presented in viewgraph form are functional block diagrams of the SARSAT distress beacon and beacon RF module as well as performance goals, schematic diagrams, predicted performances, and measured performances for the phase modulator and power amplifier.
Petersen, Wendell C.↗
Pressure-Tolerant 3D Anodes Enable Short-Circuit Prevention and Low Heat Generation in Argyrodite Solid-State Batteries
Solid-state batteries (SSBs) offer a safer, higher-energy-density alternative to lithium-ion batteries, yet commercialization is hindered by incompatibility with lithium metal. Here, to overcome these challenges, we developed a cost-effective, commercially available prelithiated micro carbon fiber framework (Li-Cf) anode featuring a high-pressure-tolerance, for use with argyrodite solid-state electrolytes (SSEs). This 3D structure accommodates uniform lithium deposition, simplifies cell assembly under elevated pressure, inhibits dendrite growth toward SSEs, reduces heat generation, and enhances overall compatibility. Notably, our architecture enables the cell to tolerate pressures up to 400 MPa without short-circuiting during assembly. Meanwhile, the 3D framework serves as a preferential pathway for lithium deposition, thereby reducing lithium growth toward the SSEs and mitigating the risk of dendrite formation in SSEs. Operando calorimetry and distribution of relaxation times analysis reveal that lithium morphology degradation at the interface with the SSEs is a key failure mechanism in lithium metal argyrodite SSBs, leading to increased diffusion resistance and heat generation. In contrast, the Li-Cf anode mitigates these issues by reducing both heat flux and charge transfer resistance. Full cells with LiNi 0.8 Co 0.1 Mn 0.1 O 2 /Li 6 PS 5 Cl/Li-Cf retain ~79% capacity after 600 cycles, demonstrating significantly improved cycling stability and strong potential for practical energy storage applications.
25 ENERGY STORAGE↗
Energy storage and thermal control system design status
The Space Station Freedom electric power system (EPS) will initially rely on photovoltaics for power generation and Ni/H2 batteries for electrical energy storage. The current design for the development status of two major subsystems in the PV Power Module is discussed. The energy storage subsystem comprised of high capacity Ni/H2 batteries and the single-phase thermal control system that rejects the excess heat generated by the batteries and other components associated with power generation andstorage is described.
Simons, Stephen N.↗
Energy storage and thermal control system design status
The Space Station Freedom electric power system (EPS) will initially rely on photovoltaics for power generation and Ni/H2 batteries for electrical energy storage. The current design for and the development status of two major subsystems in the PV Power Module is discussed. The energy storage subsystem comprised of high capacity Ni/H2 batteries and the single-phase thermal control system that rejects the excess heat generated by the batteries and other components associated with power generation and storage is described.
Simons, Stephen N.↗
Al 2 O 3 /TiO 2 coated separators: Roll-to-roll processing and implications for improved battery safety and performance
Heat generation is one of the major concerns with lithium-ion batteries (LIB) while charging them at higher currents, which could inadvertently impact the rate performance and reduce the safety of the cell. Polymer separator is one of the least thermal conductive components of a LIB. In addition, commercial separators for LIB are made from polyolefin membranes that tend to shrink and curl at higher temperatures due to their lower melting temperature (~130 °C). Developing separators with improved thermal stability and higher electrolyte uptake is essential for enhancing the safety as well as the performance of the LIB. In this work, a thin layer of ceramic coatings (Al 2 O 3 and TiO 2 ) is applied on propylene (PP) membrane to improve the thermal stability and electrolyte affinity without compromising the rate performance. A slurry with 100% Al 2 O 3 coated on the polypropylene separator exhibited the best improvement in thermal stability ( shrinkage of 0.6% vs 6.0% for uncoated membrane) and excellent rate performance with 92% capacity retention at 2C. The Al 2 O 3 coated separator demonstrated excellent electrolyte wettability compared to the uncoated membrane. The cross-plane thermal conductivity of the ceramic coated separators is analyzed to understand their heat transfer behavior. The thermal conductivity of the separator is improved by ~3.2 times with the Al 2 O 3 coating.
25 ENERGY STORAGE↗
The Role of Interfacial Thermal Resistance in Li-Ion Battery Thermal Management: Preprint
Temperature critically affects the performance, life and safety of lithium-ion batteries. Therefore, it is essential to understand heat generation and dissipation within individual battery cells and battery packs to plan a proper thermal management strategy. One of the key challenges is that interfacial heat transfer of a battery unit is difficult to quantify. The steady-state absolute method and the transient laser-flash-diffusivity method were employed to measure heat conductivities of battery layer stacks and individual battery layer separately. Results show flash diffusivity method gives higher thermal conductivity at both cross-plane and in-plane directions. The difference is primarily caused by interfacial thermal resistance so that it can be estimated by steady-state and transient measurements. To investigate the effects of interfacial thermal transport beyond individual cell level, a multiphysics battery model is used. The model is built upon a multi-scale multi-domain modeling framework for battery packs that accounts for the interplay across multiple physical phenomena. Benefits of a battery module using thermal management materials are quantified through numerical experiments. During a thermal runaway event, it is found interfacial thermal resistance can mitigate thermal runaway in a battery module by significantly reducing heat transfer between cells.
33 ADVANCED PROPULSION SYSTEMS↗
Milli-Watt Radioisotope Power to Enable Small, Long-Term Robotic “Probe” Space Exploration
Milli-watt Radioisotope Power Systems (RPS) based on Radioisotope Heater Units (RHUs) could be an ideal power source for certain spacecraft that cannot use solar power due to large distances from the sun, or other environmental constraints, and where they enable or significantly enhance the ability of a mission to meet its scientific or operational goals. Various modular, compact RHU-based thermoelectric (TE) generator concepts developed or derived from current NASA Small Business Innovation Research (SBIR) projects satisfying this need have been investigated. These modular, compact and low mass power systems could support small, highly-mobile robotic exploration packages, and could be incorporated into different robotic package concepts, spacecraft or satellites. Current modular RPS design concepts with 40mW, 80mW and 120mW power levels use RHUs and Bi2Te3 TE converters. Skutterudites materials could be used in the future if new higher thermal energy output and higher temperature miniature heat sources were developed, for example, using technologies currently in the General Purpose Heat Source (GPHS) used in higher electric power output RTGs. Small (a.k.a., “mice-like”) robotic packages could effectively utilize these RHU-driven power levels to accommodate crawling, climbing, monitoring, taking measurements, and communicating during long-term planetary missions aimed at gathering environmental and geologic data (i.e., over multiple decades). Waste heat from the cold side of the TE converter could also be directed toward the electronics and / or energy storage (e.g. batteries) to keep them within design temperature ranges. In addition to power generation and electronics / battery heating, the RHU / TE configuration could be designed to survive an external 500°C bake out procedure for critical spacecraft sterilization, environmental certification and planetary protection. Analytical studies have been performed to optimize various design configurations for power, mass, volume and robotic mobility. Specific power (mW/kg) and volumetric specific power (mW/cm3) characteristics of various design configurations will be presented and key conceptual design tradeoffs will be discussed. Hot- and cold-side thermal interfaces required to meet power and mass goals and associated design sensitivities will also be discussed. RHU / TE systems must overcome critical design challenges to survive high-g loadings in some robotic applications and we will examine the mass impacts required to satisfy various dynamic loading environments up to 10,000 g’s. Power can be generated for a minimum of 30 years or more using plutonium-238 dioxide heat sources (given that Pu-238 has an 87.7 year half-life) with some reduction in power as the heat source naturally degrades.
Bahrami, Poyan↗