Search NASA⌕ Search

SEARCH · Search NASA

Results for “biochar”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Effect of Biochar and Biochar Particle Size on Plant-Available Water of Sand, Silt Loam, and Clay Soil

Biochar is being used as a soil amendment to improve soil hydraulic properties. It has been reported that biochar increases plant-available water, particularly in coarse-textured soils; however, effects on fine-textured soils are less pronounced. Here, we quantified the effects of biochar particle size on plant-available water in sand, silt loam, and clay soils. We amended these soils with a hydrophilic biochar, and packed soil-biochar mixtures into columns of 5.35-cm diameter and 3.0-cm height. Biochar was produced by gasification of woody forest residues. We applied the biochar at two different rates (0.5\% and 2\% by weight of C) and with four different biochar particle-size fractions ($<$4.75, $<$2.0, $<$1.0 and $<$0.5 mm). Our results show that biochar amendments increased the plant-available water (when expressed gravimetrically) of all three soils, particularly at the highest biochar application rate. Although the absolute increase in plant-available water was largest for the silt loam soil, the relative increase of plant-available water was greater for the sand than for the silt loam and clay. When expressed in volumetric terms, however, the effects on water retention were less pronounced: the sand showed a small increase in plant-available water with biochar amendment, and no change was observed with the silt loam and clay. Particle size of biochar had little effect on plant-available water (when expressed in gravimetric terms) in the three soils, but silt loam and clay showed increased plant-available water (when expressed in volumetric terms) with decreasing biochar particle size, while no effect was observed for the sand. While our findings corroborate many of the previously reported effects of biochar on soil-water retention, we show that the effects and their magnitude depend on whether the results are reported in terms of gravimetric or volumetric water contents. Because bulk density tends to decrease with increasing biochar application, so will the volumetric water content, and thus the magnitude of the effect on plant-available water will be smaller when expressed in volumetric water content.

hydraulic properties, water holding capacity, soil↗

Sub-volt conversion of activated biochar and water for H 2 production near equilibrium via biochar-assisted water electrolysis

Sluggish water oxidation reactions limit water electrolysis for H 2 production, which can be alleviated by the use of carbon-based ma- terials like agricultural wastes as reducing agents. Biochar from such biomass can reduce equilibrium cell potentials at standard condi- tions from 1.23 V to 0.21 V by avoiding direct water splitting at the anode. However, some challenges hinder biochar oxidation, including poor biochar binding, electrode caking, and surface passivation. We find that enhanced C/O ratio, crystallinity, and negative zeta potential improve biochar oxidation kinetics at mod- erate temperatures. Smaller particle sizes and better mixing pre- vent electrode caking, enhancing biochar stability. Here, we report sub-volt biochar-coupled H 2 production, often referred to as a bio- char-assisted water electrolysis (BAWE), yielding 250 mA/g cat H 2 current at 100% Faradaic efficiency. Over 1 mA current was observed at a near-equilibrium cell potential of 0.2 V cell potential. Using a single-junction solar cell-powered BAWE, 15 mA H 2 is generated at 1 Sun, resulting in 4.8% solar-to-hydrogen efficiency, equivalent to 35% when the energy of H 2 relative to H 2 O (without biochar) is assumed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Relevant biochar characteristics influencing compressive strength of biochar-cement mortars

To counteract the contribution of CO 2 emissions by cement production and utilization, biochar is being harnessed as a carbon-negative additive in concrete. Increasing the cement replacement and biochar dosage will increase the carbon offset, but there is large variability in methods being used and many researchers report strength decreases at cement replacements beyond 5%. This work presents a reliable method to replace 10% of the cement mass with a vast selection of biochars without decreasing ultimate compressive strength, and in many cases significantly improving it. By carefully quantifying the physical and chemical properties of each biochar used, machine learning algorithms were used to elucidate the three most influential biochar characteristics that control mortar strength: initial saturation percentage, oxygen-to-carbon ratio, and soluble silicon. These results provide additional research avenues for utilizing several potential biomass waste streams to increase the biochar dosage in cement mixes without decreasing mechanical properties.

97 MATHEMATICS AND COMPUTING↗

Structural Characterization of Loblolly Pine Derived Biochar by X-ray Diffraction and Electron Energy Loss Spectroscopy

Biochar from lignocellulosic biomass is emerging as a sustainable material with versatile applications, but its detailed properties are poorly understood because of its structural complexity. We propose a biochar structural development model based on experimental results including composition analysis, surface area and pore analysis, X-ray diffraction analysis, electron microscopy imaging, and electron energy loss spectroscopy. Loblolly pine derived biochars were produced at different carbonization temperatures between 300 to 1000 °C. Fixed carbon, sp 2 content, and number of graphene layers increased with increased carbonization temperature. Alternating average C–C bond length, interlayer spacing distance, and layer coherence length were observed. Bulk plasmon excitation energy was correlated to the average C–C bond length, and it serves as a good indicator of the carbon structure development when compared to the perfect graphitic carbon structure. On the basis of the experimental results, four different structural development phases are identified, which provide a comprehensive understanding of biochar nanocarbon crystallite development. Unlike previous biochar structure models, which proposed radially growing polyaromatic carbon crystallite, we propose a lengthwise growing polyaromatic carbon crystallite model. Furthermore, this experiment-based biochar model should be helpful when determining the structure of unknown biomass-derived carbon materials and disordered pyrolytic carbon materials.

Biomass carbonization↗

Microwave-Assisted Gasification of Biochar: Effect of Operational Parameters and Biochar Composition on Syngas Production

The utilization of microwave-assisted gasification for biomass/plastic is a promising route toward clean energy production, contributing to a reduction in carbon footprint. This method facilitates the conversion of biomass into syngas with enhanced hydrogen (H2) yield, surpassing conventional heating approaches. However, the gasification of biochar, a byproduct resulting from the initial rapid pyrolysis of biomass, appears as a rate-determining step in biomass gasification. To ensure high conversion efficiency, particularly in pilot or larger scales, the maintenance of high biochar reactivity is essential, which can be achieved by introducing catalysts to minimize biochar formation. Furthermore, given the susceptibility of biochar to microwave heating, gaining a comprehensive understanding of its behavior in the presence of microwave-active catalysts under microwave conditions is crucial to obtain valuable insights into the underlying mechanisms, thereby improving overall biomass gasification efficiency. In the previous study, magnetite (Fe3O4) was selected for microwave-assisted gasification for biomass/plastic due to its dual role as a catalyst and microwave absorber and demonstrated considerably enhanced hydrogen production. Herein, Fe3O4 is rationally modified with metal promoters and their synergistic effect toward biochar gasification performance is investigated. The data shows that metal promoted Fe3O4 shows a higher syngas yield than that of pristine Fe3O4 in biochar.

Mai, Duy Hien↗