SEARCH · Search NASA

Results for “biomass productivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Atmospheric leakage and condensate production in NASA's biomass production chamber. Effect of diurnal temperature cycles

A series of tests were conducted to monitor atmospheric leakage rate and condensate production in NASA's Biomass Production Chamber (BPC). Water was circulated through the 64 plant culture trays inside the chamber during the tests but no plants were present. Environmental conditions were set to a 12-hr photoperiod with either a matching 26 C (light)/20 C (dark) thermoperiod, or a constant 23 C temperature. Leakage, as determined by carbon dioxide decay rates, averaged about 9.8 percent for the 26 C/20 C regime and 7.3 percent for the constant 23 C regime. Increasing the temperature from 20 C to 26 C caused a temporary increase in pressure (up to 0.5 kPa) relative to ambient, while decreasing the temperature caused a temporary decrease in pressure of similar magnitude. Little pressure change was observed during transition between 23 C (light) and 23 C (dark). The lack of large pressure events under isothermal conditions may explain the lower leakage rate observed. When only the plant support inserts were placed in the culture trays, condensate production averaged about 37 liters per day. Placing acrylic germination covers over the tops of culture trays reduced condensate production to about 7 liters per day. During both tests, condensate production from the lower air handling system was 60 to 70 percent greater than from the upper system, suggesting imbalances exist in chilled and hot water flows for the two air handling systems. Results indicate that atmospheric leakage rates are sufficiently low to measure CO2 exchange rates by plants and the accumulation of certain volatile contaminants (e.g., ethylene). Control system changes are recommended in order to balance operational differences (e.g., humidity and temperature) between the two halves of the chamber.

Wheeler, Raymond M.↗

DOE OSTI2026

Data for Propagation Method and Planting Density Influence Canopy Developmental Transition and Biomass Productivity in Miscanthus × giganteus

Understanding how establishment practices influence the mechanisms underlying Miscanthus × giganteus (miscanthus) productivity and canopy development is critical for optimizing management. Data was collected during the juvenile (2011–2013) and mature (2024) phases of a long-term field experiment established in Urbana, Illinois, to evaluate the effects of propagation method (plug propagation [PP] and rhizome propagation [RP]), planting density (1.0, 0.75, and 0.25 plants m⁻²), and nitrogen application (0 and 67 kg N ha⁻¹) on end-of-season biomass yield, tiller mass, tiller density, and tiller height. Linear regression models identified the dominant predictors of yield across stand ages and management regimes. Planting density, nitrogen (N) application, and propagation method significantly influenced early yield and canopy development. During the juvenile phase, biomass yield was driven by tiller density due to canopy expansion; in the mature phase, yield became driven by tiller mass. The PP plots produced higher tiller density than the RP plots, resulting in faster canopy closure and higher juvenile-phase yields. Rhizome-propagated (RP) plots produced lower tiller density, but individual tillers were 3.3–6.4 g tiller−1 heavier than PP tillers. After the canopy reached equilibrium, the PP and RP yields were similar because greater RP tiller mass compensated for its lower tiller density. Higher planting density resulted in greater yield and tiller density during the second year (2012), but this effect was absent from the third year (2013) onward. In the juvenile phase, N fertilization enhanced yield by 1.6–3.4 Mg ha−1. Initiating fertilization in 2013 on unfertilized plots produced biomass similar to that in fertilized plots, suggesting yield recovery in the mature phase. These findings revealed that establishment strategies, including propagation method and planting density, influence juvenile miscanthus canopy development and productivity, transitioning from tiller-density- to mass-dominated yields, but not mature phase productivity.

Miscanthus↗

DOE OSTI2020

Biomass Production of Prairie Cordgrass (Spartina pectinata Link.) Using Urea and Kura Clover (Trifolium ambiguum Bieb.) as a Source of Nitrogen

Abstract Optimizing nitrogen (N) management is an important factor for sustainable perennial biomass systems. However, N application is costly, both financially and environmentally. Our objectives were to determine: (1) N rate and plant spacing effects on yield and yield components of prairie cordgrass swards and (2) fertilizer N replacement value (FNRV) of kura clover in prairie cordgrass-kura clover binary mixtures. Plots were established in Illinois, Minnesota, South Dakota, and Wisconsin, USA, in 2010. Kura clover was transplanted on 30-cm centers in all treatments in which it was a component; prairie cordgrass seedlings were transplanted within the kura clover on 60- and 90-cm centers. Monoculture prairie cordgrass stands were established at the same population densities of mixed stands and fertilized with 0, 75, 150, or 225 kg N ha -1 . Biomass was harvested in the autumn from 2011 to 2013. N (urea), year, plant spacing, and year × plant spacing affected prairie cordgrass production at all locations. Prairie cordgrass yield increased with N application, but the response varied by location. N application tended to increase prairie cordgrass tiller density and consistently increased tiller mass. Prairie cordgrass yield with 0 N was equal to or less than the yield of prairie cordgrass/kura clover mixtures at all locations in 2011 and 2012; however, kura clover provided a FNRV of 25–82 kg N ha -1 to prairie cordgrass in 2013. Kura clover has potential to provide N to prairie cordgrass in binary mixtures of these two species and on land that may not be easily farmed due to wetness.

Energy & Fuels↗

NASA NTRS1993

Validated environmental and physiological data from the CELSS Breadboard Projects Biomass Production Chamber. BWT931 (Wheat cv. Yecora Rojo)

This KSC database is being made available to the scientific research community to facilitate the development of crop development models, to test monitoring and control strategies, and to identify environmental limitations in crop production systems. The KSC validated dataset consists of 17 parameters necessary to maintain bioregenerative life support functions: water purification, CO2 removal, O2 production, and biomass production. The data are available on disk as either a DATABASE SUBSET (one week of 5-minute data) or DATABASE SUMMARY (daily averages of parameters). Online access to the VALIDATED DATABASE will be made available to institutions with specific programmatic requirements. Availability and access to the KSC validated database are subject to approval and limitations implicit in KSC computer security policies.

Stutte, G. W.↗

DOE OSTI2023

Algal Biomass Production via Open Pond Algae Farm Cultivation: 2022 State of Technology and Future Research

The annual State of Technology (SOT) assessment is an essential activity for platform research conducted under the Bioenergy Technologies Office (BETO). It allows for the impact of research progress (both directly achieved in-house at the National Renewable Energy Laboratory [NREL] and furnished by partner organizations) to be quantified in terms of economic improvements in the overall biofuel production process for a particular biomass processing pathway, whether based on terrestrial or algal biomass feedstocks. As such, initial benchmarks can be established for currently demonstrated performance, and progress can be tracked toward out-year goals to ultimately demonstrate economically viable biofuel technologies. NREL's algae SOT benchmarking efforts focus both on front-end algal biomass production and separately on back-end conversion to fuels through NREL's "combined algae processing" (CAP) pathway. The production model is based on outdoor long-term cultivation data, enabled by comprehensive algal biomass production trials conducted under the Development of Integrated Screening, Cultivar Optimization, and Verification Research (DISCOVR) consortium efforts, driven by data furnished by Arizona State University (ASU) at the Arizona Center for Algae Technology and Innovation (AzCATI) testbed site. The CAP model is based on experimental efforts conducted primarily under NREL research and development projects. This report focuses on front-end algal biomass production, documenting the pertinent algal biomass cultivation parameters that were input to the NREL open pond algae farm model. Through partnerships under DISCOVR, collaborators at ASU furnished details on cultivation performance metrics including biomass productivity and harvest densities for recent growth trials done at the AzCATI site. The resulting biomass productivity was calculated at 18.5 g/m2/day (ash-free dry weight [AFDW], annual average) for seasonal cultivation of Picochlorum celeri, Tetraselmis striata LANL1001, and Monoraphidium minutum 26B-AM biomass strains at the ASU site. Picochlorum celeri achieved the best productivity from May to September, with Monoraphidium minutum 26B-AM being used in October, November, March, and April, and Tetraselmis striata employed during winter months (December through February). Beyond the standard SOT models, in Appendix C of this report we also present an industry case study evaluating several scenarios reflective of outdoor cultivation data furnished by an industry collaborator. This case study provides a supplementary datapoint on work being performed elsewhere achieving comparable cultivation productivity with more favorable compositional quality, producing biomass enriched in lipids as may be more optimal for conversion upgrading to fuels and products.

09 BIOMASS FUELS↗

DOE OSTI2024

Algal Biomass Production via Open Pond Algae Farm Cultivation: 2023 State of Technology and Future Research

The annual State of Technology (SOT) assessment is an essential activity for platform research conducted under the Bioenergy Technologies Office (BETO). It allows for the impact of research progress (both directly achieved in-house at the National Renewable Energy Laboratory [NREL] and furnished by partner organizations) to be quantified in terms of economic improvements in the overall biofuel production process for a particular biomass processing pathway, whether based on terrestrial or algal biomass feedstocks. As such, initial benchmarks can be established for currently demonstrated performance, and progress can be tracked toward out-year goals to ultimately demonstrate economically viable biofuel technologies. NREL's algae SOT benchmarking efforts historically focused both on front-end algal biomass production and separately on back-end conversion to fuels through NREL's "combined algae processing" (CAP) pathway. The production model is based on outdoor long-term cultivation data, enabled by comprehensive algal biomass production trials conducted under the Development of Integrated Screening, Cultivar Optimization, and Verification Research (DISCOVR) consortium efforts, driven by data furnished by Arizona State University (ASU) at the Arizona Center for Algae Technology and Innovation (AzCATI) testbed site. The CAP model is based on experimental efforts conducted primarily under NREL research and development projects. This report focuses on front-end algal biomass production, documenting the pertinent algal biomass cultivation parameters that were input to the NREL open pond algae farm model. Through partnerships under DISCOVR, collaborators at ASU furnished details on cultivation performance metrics including biomass productivity and harvest densities for recent growth trials done at the AzCATI site. The resulting biomass productivity was calculated at 16.7 g/m 2 /day (ash-free dry weight [AFDW], annual average) for seasonal cultivation of Picochlorum celeri TG2 and Monoraphidium minutum 26B-AM biomass strains at the ASU site. Picochlorum celeri achieved the best productivity from April to September, with Monoraphidium minutum 26B-AM being used between October and March. Tetraselmis striata LANL1001, usually part of the strain rotation in previous cultivation SOTs, was supplanted by Monoraphidium minutum 26B-AM in this year's outdoor cultivation trials. Finally, building from an industry case study presented in the 2022 SOT report, in the Appendix of this report we provide an update on further improved data furnished by an industry collaborator and resultant impacts on economics reflecting several seasonal scenarios. This case study provides a supplementary datapoint on work being performed elsewhere with a more dedicated focus on improved compositional quality, producing biomass enriched in lipids as may be more optimal for conversion upgrading to fuels and products.

09 BIOMASS FUELS↗

NASA NTRS1996

Proximate composition of CELSS crops grown in NASA's Biomass Production Chamber

Edible biomass from four crops of wheat (Triticum aestivum L.), four crops of lettuce (Lactuca sativa L.), four crops of potato (Solanum tuberosum L.), and three crops of soybean (Glycine max (L.) Merr.) grown in NASA's CELSS Biomass Production Chamber were analyzed for proximate composition. All plants were grown using recirculating nutrient (hydroponic) film culture with pH and electrical conductivity automatically controlled. Temperature and humidity were controlled to near optimal levels for each species and atmospheric carbon dioxide partial pressures were maintained near 100 Pa during the light cycles. Soybean seed contained the highest percentage of protein and fat, potato tubers and wheat seed contained the highest levels of carbohydrate, and lettuce leaves contained the highest level of ash. Analyses showed values close to data published for field-grown plants with several exceptions: In comparison with field-grown plants, wheat seed had higher protein levels; soybean seed had higher ash and crude fiber levels; and potato tubers and lettuce leaves had higher protein and ash levels. The higher ash and protein levels may have been a result of the continuous supply of nutrients (e.g., potassium and nitrogen) to the plants by the recirculating hydroponic culture.

NASA Discipline Life Support Systems↗

NASA NTRS1990

System development and early biological tests in NASA's biomass production chamber

The Biomass Production Chamber at Kennedy Space Center was constructed to conduct large scale plant growth studies for NASA's CELSS program. Over the past four years, physical systems and computer control software have been continually upgraded and the degree of atmospheric leakage from the chamber has decreased from about 40 to 5 percent of the total volume per day. Early tests conducted with a limited degree of closure showed that total crop (wheat) growth from the best trays was within 80 percent of reported optimal yields for similar light levels. Yields from subsequent tests under more tightly closed conditions have not been as good--up to only 65 percent of optimal yields. Yields appear to have decreased with increasing closure, yet potential problems exist in cultural techniques and further studies are warranted. With the ability to tightly seal the chamber, quantitative data were gathered on CO2 and water exchange rates. Results showed that stand photosynthesis and transpiration reached a peak near 25 days after planting, soon after full vegetative ground cover was established. In the final phase of testing when atmospheric closure was the highest, ethylene gas levels in the chamber rose from about 10 to nearly 120 ppb. Evidence suggests that the ethylene originated from the wheat plants themselves and may have caused an epinastic rolling of the leaves, but no apparent detrimental effects on whole plant function.

Wheeler, R. M.↗

NASA NTRS1994

Performance and reliability of the NASA biomass production chamber

The Biomass Production Chamber (BPC) at the Kennedy Space Center is part of the Controlled Ecological Life Support System (CELSS) Breadboard Project. Plants are grown in a closed environment in an effort to quantify their contributions to the requirements for life support. Performance of this system is described. Also, in building this system, data from component and subsystem failures are being recorded. These data are used to identify problem areas in the design and implementation. The techniques used to measure the reliability will be useful in the design and construction of future CELSS. Possible methods for determining the reliability of a green plant, the primary component of CELSS, are discussed.

Fortson, R. E.↗

NASA NTRS1994

Performance and reliability of the NASA Biomass Production Chamber

Sager, J. C.↗

NASA NTRS1990

Biomass production and nitrogen dynamics in an integrated aquaculture/agriculture system

A combined aquaculture/agriculture system that brings together the three major components of a Controlled Ecological Life Support System (CELSS) - biomass production, biomass processing, and waste recycling - was developed to evaluate ecological processes and hardware requirements necessary to assess the feasibility of and define design criteria for integration into the Kennedy Space Center (KSC) Breadboard Project. The system consists of a 1 square meter plant growth area, a 500 liter fish culture tank, and computerized monitoring and control hardware. Nutrients in the hydrophonic solution were derived from fish metabolites and fish food leachate. In five months of continuous operation, 27.0 kg of lettuce tops, 39.9 kg of roots and biofilm, and 6.6 kg of fish (wet weights) were produced with 12.7 kg of fish food input. Based on dry weights, a biomass conversion index of 0.52 was achieved. A nitrogen budget was derived to determine partitioning of nitrogen within various compartments of the system. Accumulating nitrogen in the hypoponic solution indicated a need to enlarge the plant growth area, potentially increasing the biomass production and improving the biomass conversion index.

Owens, L. P.↗

DOE OSTI2021

Algal Biomass Production via Open Pond Algae Farm Cultivation: 2020 State of Technology and Future Research

The annual State of Technology (SOT) assessment is an essential activity for platform research conducted under the Bioenergy Technologies Office. It allows for the impact of research progress to be quantified in terms of economic improvements in the overall biofuel production process for a particular biomass processing pathway, whether based on terrestrial or algal biomass feedstocks. As such, initial benchmarks can be established for currently demonstrated performance, and progress can be tracked towards out-year goals to ultimately demonstrate economically viable biofuel technologies. NREL's algae state of technology benchmarking efforts focus both on front-end algal biomass production and separately on back-end conversion to fuels through NREL's "combined algae processing" (CAP) pathway. The production model is based on outdoor long-term cultivation data, enabled by comprehensive algal biomass production trials conducted under Development of Integrated Screening, Cultivar Optimization, and Verification Research (DISCOVR) consortium efforts, driven by data furnished by Arizona State University (ASU) at the Arizona Center for Algae Technology and Innovation (AzCATI) testbed site. The CAP model is based on experimental efforts conducted under NREL research and development projects. This report focuses on front-end algal biomass production, documenting the pertinent algal biomass cultivation parameters that were input to the NREL open pond algae farm model based on the latest DISCOVR cultivation performance data. Relative to prior 2019 benchmarks, the 2020 algae farm SOT achieved further reductions in modeled minimum biomass selling price of approximately $70/ton (roughly 10%), primarily attributable to a 16% demonstrated improvement in annual average cultivation productivity rates.

09 BIOMASS FUELS↗

DOE OSTI2022

Algal Biomass Production via Open Pond Algae Farm Cultivation: 2021 State of Technology and Future Research

The annual State of Technology (SOT) assessment is an essential activity for platform research conducted under the Bioenergy Technologies Office. It allows for the impact of research progress to be quantified in terms of economic improvements in the overall biofuel production process for a particular biomass processing pathway, whether based on terrestrial or algal biomass feedstocks. As such, initial benchmarks can be established for currently demonstrated performance, and progress can be tracked towards out-year goals to ultimately demonstrate economically viable biofuel technologies. NREL's algae state of technology benchmarking efforts focus both on front-end algal biomass production and separately on back-end conversion to fuels through NREL's "combined algae processing" (CAP) pathway. The production model is based on outdoor long-term cultivation data, enabled by comprehensive algal biomass production trials conducted under Development of Integrated Screening, Cultivar Optimization, and Verification Research (DISCOVR) consortium efforts, driven by data furnished by Arizona State University (ASU) at the Arizona Center for Algae Technology and Innovation (AzCATI) testbed site. The CAP model is based on experimental efforts conducted under NREL research and development projects. This report focuses on front-end algal biomass production, documenting the pertinent algal biomass cultivation parameters that were input to the NREL open pond algae farm model based on the latest DISCOVR cultivation performance data. Relative to the fiscal year (FY) 2020 SOT at $683/ton or $603/ton for ASU and FA evaporation scenarios, respectively (unlined pond basis), the FY 2021 SOT represents a slight increase in MBSP of 1%-2%. This is primarily attributed to a slight 4% reduction in annual cultivation productivity achieved at the AzCATI site (supported by the efforts under the DISCOVR consortium noted above) observed during FY 2021 cultivation campaigns.

09 BIOMASS FUELS↗

DOE OSTI2022

Oxygen stress mitigation for microalgal biomass productivity improvement in outdoor raceway ponds

Dissolved oxygen (DO) concentrations at supersaturated levels are commonly observed in outdoor microalgae cultures due to photosynthesis during periods of rapid growth. Paradoxically, the photosynthetically generated oxygen is inhibitory and lowers biomass productivity, therefore, increasing the cost of microalgal biofuels. In this study, photosynthetic rates of Monoraphidium minutum 26B-AM and Scenedesmus obliquus UTEX393, two of the top DISCOVR strains, were compared at three DO levels, 0, 8, and 30 mg L -1 . Increasing DO from 0 to 30 mg L -1 caused a 36.6% and 26.1% reduction in photosynthetic rate for M. minutum 26B-AM and S. obliquus UTEX393, respectively. To improve the outdoor pond biomass productivity of each strain, three oxygen stress mitigation methods were tested. The first method raised the dissolved bicarbonate concentration by an order of magnitude to favor bicarbonate transport into the cell, increasing the CO 2 :O 2 ratio near RuBisCO, thus reducing photorespiration. Although this method increased the observed photosynthesis rate of M. minutum 26B-AM by 26% and S. obliquus UTEX393 by 13% in laboratory testing, it failed to improve biomass productivity under outdoor pond conditions for both strains. The second method added sodium sulfite as an oxygen scavenger to chemically lower the DO concentration in the culture. Chemical reduction of dissolved molecular oxygen did not significantly improve the biomass productivity of M. minutum 26B-AM; however, a 10% improvement in biomass productivity for S. obliquus UTEX393 was observed. The final method sparged cultures with air to strip oxygen out of the liquid medium. This did not improve the biomass productivity of M. minutum 26B-AM, likely due to unfavorable weather conditions during cold season cultivation; however, an improvement of 36% in biomass productivity was achieved for S. obliquus UTEX393 during the warm season cultivation. Of the three tested methods, air-sparging was the most effective and practical for improving outdoor biomass production.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2025

Enhancing Biomass Productivity by Forecast‐Informed Pond Operations

ABSTRACT Microalgal cultivation for biofuels and proteins holds significant promise but faces challenges in achieving economically viable biomass productivity under variable environmental conditions. This study introduces a forecast‐informed pond operation (FIPO) system that uses numerical weather prediction (NWP) ensemble forecasts and the biomass assessment tool (BAT) to optimize daily dilution rates for enhanced biomass production. In contrast to the current practice, where fixed dilution rates are based on operator experience, the FIPO system determines the optimal dilution rate based on future weather forecasts and biomass growth conditions. Our experiments validate the effectiveness of FIPO in both short‐ and long‐term growth scenarios. In short‐term experiments, FIPO increased biomass production by 21.3% compared to batch growth and 7.4% over fixed dilution (60% every 3 days) operations. The NWP forecast‐informed operations achieved biomass production nearly identical to that using perfect weather forecasts, highlighting the accuracy of current NWP forecasts for guiding pond operations. In long‐term experiments, FIPO resulted in biomass production increases of 13.3% and 17.8% compared to two fixed dilution rates (60% every 3 days and 20% daily). These findings underscore the viability of using NWP forecasts to optimize microalgal cultivation systems. By adjusting daily dilution rates in response to forecasted weather, operators can achieve higher biomass yields and mitigate risks associated with environmental variability. This study provides a foundation for future research and practical applications in commercial‐scale microalgal production.

Yan, Hongxiang [Energy and Environment Directorate↗

DOE OSTI2022

Improving Microalgal Biomass Productivity Using Weather-Forecast-Informed Operations

The operation of microalgal cultivation systems, such as culture dilution associated with harvests, affects biomass productivity. However, the constantly changing incident light and ambient temperature in the outdoor environment make it difficult to determine the operational parameters that result in optimal biomass growth. To address this problem, we present a pond operation optimization tool that predicts biomass growth based on future weather conditions to identify the optimal dilution rate that maximizes biomass productivity. The concept was tested by comparing the biomass productivities of three dilution scenarios: standard batch cultivation (no dilution), fixed-rate dilution (harvest 60% of the culture every three days), and weather-forecast-informed dilution. In the weather-forecast-informed case, the culture was diluted daily, and the dilution ratio was optimized by the operation optimization tool according to the future 24 h weather condition. The results show that the weather-forecast-informed dilution improved the biomass productivity by 47% over the standard batch cultivation and 20% over the fixed-rate dilution case. These results demonstrate that the pond operation optimization tool could help pond operators to make decisions that maximize biomass growth in the field under ever-changing weather conditions.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2024

Factorial experiment to identify two-way interactions between temperature, harvesting period, hydraulic retention time, and light intensity that influence the biomass productivity and phosphorus removal efficiency of a microalgae–bacteria biofilm

Rotating algae biofilm reactors (RABRs) can reduce energy requirements for wastewater reclamation but require further optimization for implementation at water resource recovery facilities (WRRF). Optimizing RABR operation is challenging because conditions at WRRF change frequently, and disregarding interaction terms related to these changes can produce incorrect conclusions about RABR behavior. This study evaluated the two-way interaction and main effects of four factors on the biomass productivity and phosphorus removal efficiency of a microalgae-bacteria biofilm grown in municipal anaerobic digester centrate, with factor levels and operating conditions selected to mimic a pilot RABR at a WRRF in Utah. Two-way interactions harvesting period*light intensity (LI), harvesting period*temperature, and LI*hydraulic retention time (HRT) had significant effects on biomass productivity: at high temperature and low LI, highest biomass productivity was achieved with a 14-day harvesting period, but at medium temperature and high LI, highest biomass productivity was achieved with a 7-day harvesting period. At high HRT, highest biomass productivity occurred at low LI, but at low HRT, highest biomass productivity occurred at high LI. Phosphorus removal was strongly influenced by LI and occurred most rapidly during the first 2 days HRT, which suggests precipitation contributed significantly to phosphorus removal. These observations provide insight for further RABR optimization.

09 BIOMASS FUELS↗

DOE OSTI2020

Algal Biomass Production via Open Pond Algae Farm Cultivation: 2019 State of Technology and Future Research

NREL’s algae state of technology benchmarking efforts focus both on front-end algal biomass production and separately on back-end conversion to fuels through NREL’s “combined algae processing” (CAP) pathway. The production model is based on outdoor long-term cultivation data, enabled by comprehensive algal biomass production trials conducted under Development of Integrated Screening, Cultivar Optimization, and Verification Research (DISCOVR) consortium efforts, driven by data furnished by Arizona State University (ASU) at the Arizona Center for Algae Technology and Innovation (AzCATI) testbed site. The CAP model is based on experimental efforts conducted under NREL R&D projects. This report focuses on front-end algal biomass production, documenting the pertinent algal biomass cultivation parameters that were input to the NREL open pond algae farm model and reports on key process sustainability indicators for the biomass production stage including annual biomass yields, facility power demand, and water consumption.

09 BIOMASS FUELS↗