Search NASA⌕ Search

SEARCH · Search NASA

Results for “bituminous”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Losses due to weather phenomena in the bituminous concrete construction industry in Wisconsin

The losses (costs) due to weather phenomena as they affect the bituminous concrete industry in Wisconsin were studied. The bituminous concrete industry's response to precipitation, in the form of rain, is identified through the use of a model, albeit crude, which identifies a typical industry decision-response mechanism. Using this mechanism, historical weather data and 1969 construction activity, dollar losses resulting from rain occurrences were developed.

Kuhn, H. A. J.↗
DOE OSTI2025

Cost and Performance Baseline for Fossil Energy Plants Volume 1: Bituminous Coal and Natural Gas to Electricity

This report presents an independent assessment of the cost and performance of select fossil energy power systems—pulverized coal (PC) and natural gas combined cycle (NGCC) plants—using a systematic, transparent, technical, and economic approach. This is Volume 1 of the baseline series: Bituminous Coal and Natural Gas to Electricity. The cost and performance of fossil fuel‐based generation technologies represented in this report are important inputs to assessments and determinations of technology combinations to be utilized to meet the projected demands of future power markets. From a research and development perspective, this report is used to assess goals and metrics and to provide a consistent basis for comparing developing technologies. The main report consists of fifteen power plant configurations, six PC cases (with and without carbon capture) nine NGCC cases (with and without carbon capture) and few additional cases of higher capture rate, for both PC and NGCC plants in the appendix. In addition to the report, an interactive tool was developed that allows users to manipulate six key study parameters simultaneously for each case and visualize the impact on three metrics: 1) levelized cost of electricity (LCOE), 2) cost of CO 2 capture (CCC), and 3) cost of CO 2 avoided (CCA). Following is the link to the interactive tool: https://netl.doe.gov/NETLVol1BaselineTool

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Cost and Performance Baseline for Fossil Energy Plants – Volume 1: Bituminous Coal and Natural Gas to Electricity: May 2025

This presentation at EPRI's annual Generation Sector Meeting during the Advanced Generation and Carbon Capture and Storage session provides an overview of the recently published Cost and Performance Baseline for Fossil Energy Plants – Volume 1: Bituminous Coal and Natural Gas to Electricity dated May 2025. It further connects viewers with the recently released tool/dashboard, an interactive tool that allows users to manipulate six key study parameters simultaneously for each case and visualize the impact on three metrics: 1) levelized cost of electricity (LCOE), 2) cost of CO2 captured (CCC), and 3) cost of CO2 avoided (CCA).

baseline study↗
NASA NTRS1978

Continuous extrusion of coal

A feeding method for use with bituminous coals that exhibit plasticity at elevated temperatures is described and demonstrated on a small screw extruder previously used to extrude polyethylene. A metered feed of coal heated to a temperature just below that of incipient caking (approximately 450 C) is used. Modifications to the extruder consisting of ceramic band heaters, auxiliary cooling coils on the thrust bearing and special quick opening dies are detailed. Coals successfully extruded include high volatile A bituminous coals, high volatile B bituminous coals, a high volatile C bituminous coal and a coal with high ash content. The computer program, EXTRUD, used to simulate the extruder is described. Predicted power consumption exhibits 30% scatter, which is explained by the sensitivity of the coal friction coefficient to temperature profiles. Detailed analysis reveals some discrepancies in the program that need to be resolved.

England, C.↗
DOE OSTI2025

Highly crystalline, low-ash, graphite from coal using an Fe 2 O 3 -based catalytic process with recovery and reuse of catalyst and process acid

This study presents a sustainable process for producing highly crystalline, low-ash graphite from sub-bituminous coal using an Fe 2 O 3 -based catalytic method. The process integrates coal mineral removal, catalyst regeneration, and reagent recycling into a closed-loop system. Acid-soluble Fe-residue and mineral impurities are eliminated from the solid graphite through HCl treatment, followed by hydrolytic distillation to regenerate Fe 2 O 3 and recover HCl for reuse. Coal-derived silica is removed with a KOH rinse, yielding low-ash graphite suitable for high-performance applications. The closed-loop catalytic graphitization, where the recovered Fe 2 O 3 and HCl are used in subsequent graphitization runs, produces graphite with a degree of graphitization exceeding 95%. The L a and L c crystallite sizes reach 65–78 nm and 44–48 nm, respectively, with BET surface areas of 4–10 m 2 /g and an ash content below 0.1 wt.%. Lithium-ion battery testing reveals that anodes fabricated with this graphite deliver an initial discharge capacity between 384.5 and 421.2 mAh/g, averaging 395.0 ± 19.1 mAh/g, along with initial coulombic efficiencies of 85.0–89.1%. After 100 discharge–charge cycles at 0.25C, reversible capacities remain between 358.8 and 369.7 mAh/g, while coulombic efficiency stays above 99.9%. The findings highlight that coal can serve as a viable precursor for high-quality graphite production under relatively mild conditions, avoiding the need for extreme temperatures or aggressive reagents such as hydrofluoric acid, commonly employed in conventional processes. This work demonstrates both technical feasibility and environmental benefits, emphasizing its potential to support large-scale, sustainable graphite production for applications such as lithium-ion batteries.

Catalytic graphitization↗
DOE OSTI2025

Hydrogen-rich syngas production from the steam co-gasification of low-density polyethylene and coal refuse

Gasification provides a promising pathway for transforming waste materials into valuable products, such as fuels and chemicals. Here, this study investigates the steam co-gasification of low-density polyethylene (LDPE) and compressed thickener underflow, representative of coal refuse (CR), in a drop tube reactor. The effects of feed blend ratio (0–100 wt% LDPE) and temperature (800–1000 °C) on syngas composition, tar formation, and process efficiency are examined. The high volatility of LDPE makes it more reactive than CR but also promotes the formation of 2–7 ring aromatic tars. Increasing temperature improves carbon conversion efficiency (CCE), cold gas efficiency (CGE), and syngas yield, although the lower heating value (LHV) of syngas decreases. Hydrogen is the dominant gas product, reaching 59 vol% with the H 2 /CO molar ratio ranging from 2.27 to 4.74. Synergistic effects from alkali and alkali earth metals (AAEMs), particularly K and Ca, in CR ash enhance syngas yield by catalyzing char gasification and tar cracking. Hematite (Fe 2 O 3 ) and ash from sub-bituminous/bituminous coals are explored as tar reforming catalysts. Fe 2 O 3 achieves 100 % tar reforming efficiency, while coal ash, with a lower Fe 2 O 3 content (15 wt%), is less effective at cracking polycyclic aromatic hydrocarbons, particularly naphthalene. These findings demonstrate the flexibility of co-gasification, allowing precise tuning of syngas characteristics for specific downstream applications. Further optimization of waste-derived catalysts could enhance the economic viability of gasification in waste-to-energy processes.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2026

The evolution of coal porosity during pyrolysis

Gasification of coal, municipal waste, or other organic materials is a potential hydrogen source that entails complex thermal decomposition and transport processes. This study provides a multiscale analysis of these processes for sub-bituminous (Usibelli, Healy, Alaska) and lignite (Center, North Dakota) coals and provides data useful for process design. The chemistry, mineralogy, and pore structures of pyrolyzed coal and their evolution with thermal decomposition are discussed. Samples pyrolyzed at 200–1000 °C were analyzed by small-angle neutron scattering; ultra-small, small-, and wide-angle X-ray scattering; and other complementary techniques. Scanning electron microscopy showed new pores in the high-temperature-pyrolyzed material. Upon heating, the coals became progressively denser, and the concentration of hydrogen decreased. Changes in pore volume fell into three temperature ranges: an initial, low-temperature range that, for the Usibelli coal, involved an increase in overall porosity; a mid-temperature range associated with pore volume loss; and a high-temperature range associated with significant porosity increase and char formation. This transformation was paralleled by changes in fractal dimension and correlation length. The higher the pyrolysis temperature the greater the small-pore-volume fraction and overall surface area became. Pyrolysis increased the lateral size of coal crystallites, decreased the amorphous fraction, and increased the aromatics fraction and overall coal rank. Comparisons of neutron and X-ray scattering data and subsequent water uptake studies showed that pre-dried coals can re-hydrate relatively rapidly upon exposure to air, which can significantly affect the porosity calculated from small-angle-scattering data. Fits to the cumulative porosity curves provide a method for modeling the physical and chemical transformation of hydrogen-containing feedstock during gasification.

Anovitz, Lawrence {Larry} [ORNL] (ORCID:0000000226↗
DOE OSTI2024

Bench-scale Development of a Transformational Graphene Oxide-based Membrane Process for Post-combustion CO 2 Capture

Graphene-based materials, such as graphene and graphene oxide (GO), have been considered as next-generation membrane materials. GTI Energy and The State University of New York at Buffalo (UB) have been developing a transformational GO-based membrane process (designated as GO2) that integrates a high CO 2 /N 2 selectivity membrane (GO-1) and a high CO 2 flux membrane (GO-2) for post-combustion CO 2 capture. An innovative membrane structure, consisting of GO nanochannels intercalated by single-walled carbon nanotube (SWCNT), was developed. The membrane prepared on hollow fiber substrate showed CO 2 permeance as high as 1,300 GPU with CO 2 /N 2 selectivity >200. The membranes were successfully scaled up to effective area of 50-100 cm 2 . The 50-100 cm 2 membranes showed CO 2 /N 2 selectivity ≥200 and CO 2 permeance ≥1,000 GPU for the GO-1 type, and CO 2 /N 2 selectivity ≥20 and CO 2 permeance ≥2,500 GPU for the GO-2 type. The CO 2 capture performance of the GO-based membranes was tested using a simulated flue gas. The testing results indicate that the GO-based membranes are stable in the presence of flue gas contaminants. The GO-based membranes were then further scaled up to a surface area of 1,000 cm 2 . Good stability was achieved during an integrated testing with GO-1 and GO-2 membranes using simulated flue gas. A bench-scale system was designed, constructed, and tested at the National Carbon Capture Center (NCCC). Good stability was achieved during testing of a single-stage process with >10 shutdowns/startups at NCCC. During the integrated testing, the membranes showed good stability at 50°C and 57°C. 70-90% CO 2 removal efficiencies and ≥95% CO 2 purity were validated during the steady state operation at NCCC. Techno-economic analysis indicates the GO2 membrane-based process technology provides a reduction in both the levelized cost of electricity (LCOE) and cost of capture when compared to the reference B12B case presented in the Cost and Performance Baseline for Fossil Energy Plants Volume 1: Bituminous Coal and Natural Gas to Electricity study prepared by the National Energy Technology Laboratory (NETL), before considering any system optimization or improvement opportunities. The benefits are primarily driven by a reduction in the equipment costs of the CO 2 capture process vs. the solvent-based reference process in NETL Case B12B as well as a decrease in the base plant size.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Testing- and Model- Based Optimization of Coal-fired Primary Heater Design for Indirect Supercritical CO 2 Power Cycles (Final Scientific and Technical Report)

The overall objective of this project was to perform the R&D necessary to mitigate the risk associated with the design of a primary heat exchanger for a solid-fired combustion system coupled with an indirect-fired closed-loop Brayton Cycle utilizing supercritical CO 2 . The key technological hurdle was the coupling of a solid-fuel firing system with the primary heater, which poses a singular challenge, which is the management of burner performance and operational conditions in a way to manage heat exchanger tube metal temperatures and temperature ramp rates in the absence of fluid phase change on the inside of the tubes. We designed and built the first ever pseudo power system employing a simple recuperated supercritical CO 2 closed-loop Brayton Cycle coupled to a solid-fuel fired system. Advanced coupled CFD and process modeling were used to design the primary heat exchanger (PHX), which consisted of both radiative and convective sections, to limit tube metal temperatures resulting from the heat release profile of the solid fuel flame near the radiative tubes. The heat exchanger was designed to produce finished CO 2 temperatures of 600 °C a pressure of 20.7 MPa and CO 2 flow of 5.5 kg/s. The constructed PHX was capable of 1.2 MWth heat uptake. During design of the PHX, the modeling showed that most variables influencing flame shape (burner stoichiometric ratio and register velocities and swirl) were not suitable to manage heat flux to the metal surfaces. This is because they substantially increased adiabatic flame temperature through the influence of localized stoichiometric ratio. Excess air and firing rate were the two most powerful variables that could be used to control tube surface temperatures. The coupled system was operated for a total of 407 hours, with the longest continuous run of 248 hours. For 62% of the operational time, the unit was unmanned and in automatic control. The fuels used for the testing included natural gas, two Utah Bituminous coals, woody biomass, and bagasse. During the testing we were able to verify the 1.2 MWth heat uptake and we operated at a finished CO 2 temperature of 607 °C and a pressure of 20.3 MPa simultaneously. The real-time corrosion rate of the Super 304H tube CO 2 surface in the region of the radiative section of the PHX were measured, at an approximate temperature of 550 °C. The two key variables related to corrosion rate are the pressure and flow rate of the CO 2 . A technoeconomic analysis was performed at a scale of 120 MWE. The updated analysis showed that the efficiency of an sCO 2 power producing plant will be related to the pressure drop of the PHX.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Examination of Factors Affecting the Cost and Performance of a Natural Gas Combined Cycle Equipped with Carbon Dioxide Capture

The purpose of this Technical Note is to report the findings of an examination of the effect of plausible deviations in select study assumptions on the reported cost and performance estimates for a power plant case drawn from NETL’s “Cost and Performance Baseline for Fossil Energy Plants Volume 1: Bituminous Coal and Natural Gas to Electricity” (known as the Fossil Energy Baseline). An F-Class NGCC power plant equipped with state-of-the-art, solvent-based, post-combustion carbon dioxide (CO2) capture (95 percent carbon capture rate)—designated as Case B31B.95—was selected for this work. This sensitivity analysis provides insight into the effects of parameter variations within and across selected categories—ambient conditions, construction cost, natural gas (NG) price, capacity factor, and finance—on the plant performance and capital and operating and maintenance (O&M) costs, and the subsequent impact on common figures of merit.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Quality Guidelines for Energy System Studies: Capital Cost Scaling Methodology: Revision 4b Report

The National Energy Technology Laboratory (NETL) regularly updates legacy analysis with new studies and cases as the Department of Energy objectives change, technology performance improves, costs are reduced, regulations change, market drivers are established, fuel prices fluctuate, and any number of other relevant factors vary in the market. As legacy studies are updated by NETL, the underlying performance and cost of the cases presented changes, and as such, the methods for interpreting and scaling the cost estimates change. Therefore, it is important that NETL maintain public guidance documents associated with different sets of cost estimates that delineate how a specific set, based on report vintage and/or year published, should be scaled. This Quality Guidelines for Energy System Studies report, providing guidance on capital cost scaling, should generally be applied to NETL case costs included in the report “Cost and Performance Baseline for Fossil Energy Plants Volume 1: Bituminous Coal and Natural Gas to Electricity Revision 4b,” (NETL, 2025) or any cases derived from the cases presented in the referenced report.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2025

Coal-Waste-Enhanced Filaments for Additive Manufacturing of High-Temperature Plastics and Ceramic Composites

In the United States, coal waste from over a century of mining and burning coal for heat and electricity has accumulated as mountains of coal fly ash and bottom ash and acre-size ponds, coal fines and gob. These materials can be a problem for local communities and water systems. A cost-effective process to utilize high volumes of these coal wastes in a high-value product would be beneficial to those communities by reducing the amount of waste and providing jobs, manufacturing components, and materials from the waste. Many coal-to-products technologies (e.g., carbon fibers, graphene, carbon foam) rely on carefully choosing the starting material and then altering it chemically or thermally to make the products work. Due to the wide variability of composition and coal content in typical coal waste streams, many high-volume coal waste streams are likely to be unsuitable for use in those technologies. Semplastics’ technology has been shown to utilize most types of coal waste successfully without any pre-selection or pre-processing requirements other than a nominal particle-size reduction for wastes like bottom ash. This characteristic of Semplastics’ solution may enable the use of much larger volumes of a wider range of coal wastes than other coal-to-products technologies. In this project, Semplastics leveraged its unique experience with both coal waste (fly ash or coal combustion residuals), resin materials, and 3D printing to develop 3D printer filaments using common coal wastes – bituminous coal fines and fly ash – and researched the feasibility of using other forms of coal waste as fillers. Simple 3D-printed parts were successfully produced from the coal waste enhanced filaments, which were found to have improved strength and stiffness.

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS1977

Sulfur compounds in coal

The literature on the chemical structure of the organic sulfur compounds (or functional groups) in coal is reviewed. Four methods were applied in the literature to study the sulfur compounds in coal: direct spectrometric and chemical analysis, depolymerization in drastic conditions, depolymerization in mild conditions, and studies on simulated coal. The data suggest that most of the organic sulfur in coal is in the form of thiophenic structures and aromatic and aliphatic sulfides. The relative abundance of the sulfur groups in bituminous coal is estimated as 50:30:20%, respectively. The ratio changes during processing and during the chemical analysis. The main effects are the transformation during processing of sulfides to the more stable thiophenic compounds and the elimination of hydrogen sulfide.

Attar, A.↗
NASA NTRS1978

Microbial desulfurization of coal

Experiments indicate that several sulfur-oxidizing bacteria strains have been very efficient in desulfurizing coal. Process occurs at room temperature and does not require large capital investments of high energy inputs. Process may expand use of abundant reserves of high-sulfur bituminous coal, which is currently restricted due to environmental pollution. On practical scale, process may be integrated with modern coal-slurry transportation lines.

Dastoor, M. N.↗
NASA NTRS1977

Coal extrusion in the plastic state

Continuous feeding of coal in a compressing screw extruder is described as a method of introducing coal into pressurized systems. The method utilizes the property of many bituminous coals of softening at temperatures from 350 to 425 C. Coal is then fed, much in the manner of common thermoplastics, using screw extruders. Data on the viscosity and extruder parameters for extrusion of Illinois No. 6 coal are presented.

England, C.↗
NASA NTRS1978

Coal desulfurization process

A method for chlorinolysis of coal is an organic solvent at a moderate temperautre and atmospheric pressure has been proven to be effective in removing sulfur, particularly the organic sulfur, from coal. Chlorine gas is bubbled through a slurry of moist coal in chlorinated solvent. The chlorinated coal is separated, hydrolyzed and the dechlorinated. Preliminary results of treating a high sulfutr (4.77%S) bituminous coal show that up to 70% organic sulfur, 90% hyritic sulfur and 76% total sulfur can be removed. The treated coal is dechlorinated by heating at 500 C. The presence of moisture helps to remove organic sulfur.

Hsu, G. C.↗
NASA NTRS1978

New method of feeding coal - Continuous extrusion of fully plastic coal

Continuous feeding of coal in a compressing screw extruder is described as a method of introducing coal into pressurized systems. The method utilizes the property of many bituminous coals of softening at temperatures from 350 to 400 C. Coal is then fed much in the manner of common thermoplastics, using screw extruders. Preliminary results show that coals can be extruded at rates of about 3.3 kg/MJ, similar to those for plastics.

Ryason, P. R.↗