Search NASA⌕ Search

SEARCH · Search NASA

Results for “boundary layer edge detection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Automatic Boundary-Layer Adaptation of Structured Grids in VULCAN-CFD

In supersonic and hypersonic flow computations, well-resolved boundary layers are essential for accurate quantification of surface heating and transition prediction, particularly via linear stability analysis. Grid design for hypersonic flows with shocks, boundary-layer separation, and/or complex mean flow features incorporating spanwise/azimuthal inhomogeneities is a difficult issue. In comparison to a manual grid adaptation procedure, an autonomous grid adaptation technique offers significant improvements in computing time and solution quality. The VULCAN-CFD solver already includes a validated procedure for automatic adaption of structured grids to the bow shock. The present focus is on implementing an automatic boundary-layer adaptation capability in VULCAN-CFD that adapts structured, multiblock grids to both the bow shock and the boundary layer at the same time. The boundary-layer adaptation algorithm allows the user to specify the number of cells within the boundary layer, along with the input parameters used for detecting the edge of the boundary layer, namely, the variable used in the edge detection criterion,the edge detection method, the detection direction, and the relaxation factor used during the morphing of the grid. The algorithm automatically distributes grid points along the wall-normal direction to achieve a smooth variation in grid spacing from the edge of the boundary layer to a"junction" location within the outer part of the grid. Illustrative results are presented for three different high-speed configurations: the two-dimensional flow over a cylinder at Mach 17.6 and unit Reynolds number of Re=0.38x10^6 m^-1, the axisymmetric flow over a cone-cylinder-flare model at Mach 6.0 and Re = 10.5×10^6 m^-1, and the three-dimensional flow over a blunt, 7-degree half-angle cone at 5-degree angle of attack in a Mach 9.79 flow with Re = 17.1×10^6 m^-1. The automated boundary-layer adaptation is shown to provide an adequate grid topology that is aligned with the bow shock in the outer part of the grid and also resolves the viscous boundary-layer region close to the surface.

boundary layer transition↗
NASA NTRS2024

BLAYER User Guide

Estimation of boundary layer edge or thickness is an essential aspect of utilizing high fidelity aerothermodynamic flow solutions. For viscous flow over a flat plate, the boundary layer thickness is usually defined as the distance from the wall at which the flow velocity (zero at the wall) has increased through some profile to 99% or 99.5% of the free stream velocity. In real gas flows over aerospace vehicles, a total enthalpy profile is employed for edge calculations. The importance of knowing boundary layer thickness and its relation to possible transition from laminar to turbulent flow is illustrated by Space Shuttle mission STS-114, when the appearance of tile gap filler protrusions on the nose was deemed serious enough that a crew member was called upon to exit the vehicle and remove the potential threat prior to its descent from orbit. The BLAYER utility used as part of post-processing Orion/MPCV flow solutions is a generalization of the earlier BLAYER_RESULTS utility developed following the STS-107 Columbia accident. BLAYER handles a variable number of gas species (not just 5), allows for more than one temperature and for optional extra flow quantities, and omits optional handling of Orbiter tile datasets.

momentum thicknes↗
NASA NTRS1988

Experiments and code validation for juncture flows

The turbulent flow around a juncture formed by an unswept wing and a flat plate has been experimentally studied, and the effectiveness of modifications near the wing leading edge in controlling the juncture flow field has been evaluated. The results are compared with numerical solutions of the incompressible Reynolds-averaged Navier-Stokes equations. The Baldwin-Lomax turbulence model is used in the computations. The numerical code is very time efficient, and it predicts the flow behavior well, including the detection of leading-edge vortex formation. It tends to over-predict the boundary layer thickness and the location of the vortex. Both the experiment and computations indicate that the leading edge flow separation is eliminated by the use of a leading-edge fillet designed in this study, resulting in drag reduction.

Kubendran, L. R.↗
NASA NTRS2012

Investigation of "6X" Scramjet Inlet Configurations

This work represents an initial attempt to determine what, if any, issues arise from scaling demonstration supersonic combustion scramjets to a flight scale making the engine a viable candidate for both military weapon and civilian access to space applications. The original vehicle sizes tested and flown to date, were designed to prove a concept. With the proven designs, use of the technology for applications as weapon systems or space flight are only possible at six to ten times the original scale. To determine effects of scaling, computations were performed with hypersonic inlets designed to operate a nominal Mach 4 and Mach 5 conditions that are possible within the eight foot high temperature tunnel at NASA Langley Research Center. The total pressure recovery for these inlets is about 70%, while maintaining self start conditions, and providing operable inflow to combustors. Based on this study, the primary scaling effect detected is the strength of a vortex created along the cowl edge causing adverse boundary layer growth in the inlet.

Alter, Stephen J.↗
NASA NTRS1980

Flow visualization of inflexional instabilities on a rotating disk

Experiments were conducted on a rotating disk in water using dye to observe the formation of small vortices in the boundary layer due to the inflexional nature of the boundary layer profiles in the radial and near radial directions. Such vortices have also been detected near the leading edge of swept wings and on the windward side of fuselages at angles of attack using sublimation techniques. In the present investigation, color motion pictures at 300 frames per second were taken and the vortex spacing, angles of inclination of the vortex axes and critical Reynolds numbers were determined from these films. Secondary instabilities were also observed and analyzed.

Clarkson, M. H.↗
NASA NTRS1998

Design and Performance of a Miniature Lidar Wind Profiler (MLWP)

The directional velocity of the wind is one of the most critical components for understanding meteorological and other dynamic atmospheric processes. Altitude-resolved wind velocity measurements, also known as wind profiles or soundings, are especially necessary for providing data for meteorological forecasting and overall global circulation models (GCM's). Wind profiler data are also critical in identifying possible dangerous weather conditions for aviation. Furthermore, a system has yet to be developed for wind profiling from the surface of Mars which could also meet the stringent requirements on size, weight, and power of such a mission. Obviously, a novel wind profiling approach based on small and efficient technology is required to meet these needs. A lidar system based on small and highly efficient semiconductor lasers is now feasible due to recent developments in the laser and detector technologies. The recent development of high detection efficiency (50%), silicon-based photon-counting detectors when combined with high laser pulse repetition rates and long receiver integration times has allowed these transmitter energies to be reduced to the order of microjoules per pulse. Aerosol lidar systems using this technique have been demonstrated for both Q-switched, diode-pumped solid-state laser transmitters (lambda = 523 nm) and semiconductor diode lasers (lambda = 830 nm); however, a wind profiling lidar based on this technique has yet to be developed. We will present an investigation of a semiconductor-laser-based lidar system which uses the "edge-filter" direct detection technique to infer Doppler frequency shifts of signals backscattered from aerosols in the planetary boundary layer (PBL). Our investigation will incorporate a novel semiconductor laser design which mitigates the deleterious effects of frequency chirp in pulsed diode lasers, a problem which has limited their use in such systems in the past. Our miniature lidar could be used on a future Mars lander and perhaps find its own niche in terrestrial applications due to its potential low cost an small size.

Cornwell, Donald M., Jr.↗
NASA NTRS1981

Sound measurements of the MOD-2 wind turbine generator

Sound measurements were made for the MOD-2 wind turbine generator for wind conditions of 7.6 to 13.4 m/sec and for output power ratings of about 1 to 2 NW. Both broad band and narrow band data wre obtained for a range of distances and azimuth angles from the machine. The rotor sound spectra are random in character and peak in the frequency ranges 30 to 50 Hz and 800 to 1300 Hz. Both peaks are predictable from experience with helicopter rotors and propellers. Results suggest that the lower frequency peak is due to the effects of inflow turbulence and the higher frequency peak is due to the interactions of the turbulent boundary layers with the trailing edges of the blades. The boundary layer related sound is the dominant component in the audible frequency range and determines the detectability of the machine. It could be detected at a distance of 1350 m in the upwind direction where the background noise was 30 dB (A) and at distances in excess of 2100 m in the downwind direction. Discrete frequency sound components associated with the power generation equipment are measurable in the direction normal to the axis of rotation but are not believed to be significant for detection or community response.

Hubbard, H. H.↗
NASA NTRS1992

In-flight detection of flow separation, stagnation, and transition

Flight tests were conducted to demonstrate the feasibility of simultaneous determination of: (1) boundary-layer instability and transition characteristics; (2) flow separation region; and (3) the location of the leading-edge stagnation point. Surface mounted, multi-element, micro-thin, hot-film sensors were used in conjunction with a bank of constant-temperature anemometers and a PC-based 8-channel simultaneous data acquisition system. Conventional techniques were used to determine the boundary-layer instability and transition characteristics while the flow separation and the stagnation points were determined through the presence of phase reversal signatures.

Mangalam, S. M.↗
NASA NTRS1989

The measurement of boundary layers on a compressor blade in cascade. IV - Flow fields for incidence angles of -1.5 and -8.5 degrees

Measurements, made with laser Doppler velocimetry, about a double-circular-arc compressor blade in a cascade are presented for -1.5 and -8.5 degree incidence angles and a chord Reynolds number near 500,000. Comparisons between the results of the current study and those of an earlier work at a 5.0 degree indicence are made. It is found that, in spite of the relative sophistication of the measurement techniques, transition on the pressure surface at the -1.5 degree incidence is dominated by a separation 'bubble' too small to be detected by the laser Doppler velocimeter. The development of the boundary layers at -1.5 and 5.0 degrees are found to be similar. In contrast to the flow at these two incidence angles, the leading edge separation 'bubble' is on the pressure surface for the -8.5 degree incidence.

Zierke, W. C.↗
NASA NTRS1986

Space-time correlation measurements in a compressible turbulent boundary layer

Single and dual hot-wire probes have been used to accomplish a first look at the large-eddy structure of a supersonic turbulent boundary layer. The investigation was performed in an axisymmetric turbulent boundary layer in the Ames High Reynolds Number wind tunnel. Freestream Mach number was 2.97, the boundary layer was approximately 1.2 cm thick, and Reynolds number = 15,000. Quantities measured were streamwise turbulence intensity and higher order statistics of mass-flow fluctuations, and space-time correlations of instantaneous streamwise velocity at two locations. Conditional sampling of the hot-wire signals was performed to detect the passage and describe the character of the large turbulent eddies. Results indicate that the large scale structure in compressible turbulence is similar to that at low subsonic flow speeds except at the boundary layer edge, where the intermittency region is narrowed in compressible flow.

Robinson, S. K.↗
NASA NTRS1997

Structure and Rotation of the Solar Interior: Initial Results from the MDI Medium-L Program

The medium-l program of the Michelson Doppler Imager instrument on board SOHO provides continuous observations of oscillation modes of angular degree, l, from 0 to approximately 300. The data for the program are partly processed on board because only about 3% of MDI observations can be transmitted continuously to the ground. The on-board data processing, the main component of which is Gaussian-weighted binning, has been optimized to reduce the negative influence of spatial aliasing of the high-degree oscillation modes. The data processing is completed in a data analysis pipeline at the SOI Stanford Support Center to determine the mean multiplet frequencies and splitting coefficients. The initial results show that the noise in the medium-l oscillation power spectrum is substantially lower than in ground-based measurements. This enables us to detect lower amplitude modes and, thus, to extend the range of measured mode frequencies. This is important for inferring the Sun's internal structure and rotation. The MDI observations also reveal the asymmetry of oscillation spectral lines. The line asymmetries agree with the theory of mode excitation by acoustic sources localized in the upper convective boundary layer. The sound-speed profile inferred from the mean frequencies gives evidence for a sharp variation at the edge of the energy-generating core. The results also confirm the previous finding by the GONG (Gough et al., 1996) that, in a thin layer just beneath the convection zone, helium appears to be less abundant than predicted by theory. Inverting the multiplet frequency splittings from MDI, we detect significant rotational shear in this thin layer. This layer is likely to be the place where the solar dynamo operates. In order to understand how the Sun works, it is extremely important to observe the evolution of this transition layer throughout the 11-year activity cycle.

Kosovichev, A. G.↗
NASA NTRS1995

Low altitude signature of the plasma sheet boundary layer: Observations and model

Low-altitude spacecraft on magnetotail field lines often detect a distinctive signature in the precipitating ion flux. A velocity-dispersed ion structure is often observed near the poleward boundary of the auroral oval. At the low-latitude edge of this structure an absence of precipitating ions is seen, previously referred to as 'the gap,' separating the velocity -- dispersed ions at the higher latitudes from the more diffuse, plasma sheet-like ions at lower latitudes. We present a model of low-altitude particle precipitation that reproduces these observed features in the ion spectra and provides a quantitative estimate of the downtail plasma sheet properties. The model calculations are compared with observations from the Akebono spacecraft. In this model, the dispersed ion velocity signature maps to a region in the distant plasma sheet where the plasma has a field-aligned bulk flow. The gap maps to a region in the distant magnetotail where the ion fluxes are below the detection threshold of the instrument, due to the low plasma sheet density and temperature in that region.

Onsager, T. G.↗
NASA NTRS1990

Observations of filamentary field-aligned current coupling between the magnetospheric boundary layer and the ionosphere

A distinct class of dayside high-latitude magnetic pulsations can be identified from the spatial characteristics of the disturbance field. These pulsations exhibit traveling radial patterns such as would result from moving filaments of field-aligned current interacting with the ionosphere to produce cells of Hall current and vortexlike plasma flow. Time intervals containing a series of continuous multiple vortices are investigated here. The vortices occur on the boundary between sunward and antisunward ionospheric plasma convection. Low altitude DMSP satellite particle measurements indicate that the vortices are on magnetic field lines which map to the inner edge of the magnetospheric low latitude boundary layer. No repetitive solar wind disturbance (e.g., pressure variations) appears to be associated with the events, suggesting that the vortices are related to a local magnetospheric instability. No strong correlation between interplanetary field conditions and the detection of vortices is found.

Clauer, C. R.↗
NASA NTRS1995

High spatial resolution atmospheric wind measurements with the edge technique

The edge technique is a new and powerful method for measuring small frequency shifts such as the Doppler shift of an atmospheric backscattered signal from a pulsed laser. The edge technique can be used for high spatial resolution, high accuracy ground and airborne wind measurements as well as high accuracy spaceborne wind measurements. We have recently made our first ground based wind measurements. These have a spatial resolution of 15 m and an accuracy of 25 cm/s and these measurements are presented in this paper. This is a unique capability and provides valuable information for studies of turbulent processes in the lower atmosphere. It could also be used for high sensitivity detection of wind shear and microbursts in the vicinity of airports. In addition, global wind measurements can be made with the edge technique from space with an accuracy of 1 m/s and a vertical resolution as high as 150 m in the boundary layer and 1 km through the troposphere. Such a system could make eyesafe wind measurements using well developed diode pumped solid state laser technology at 1.06 micron. Multi-pulse averaging would provide a spatially representative wind measurement.

Korb, C. Laurence↗
NASA NTRS1990

Ground observations of magnetospheric boundary layer phenomena

Several classes of traveling vortices in the dayside ionosphere convection have been detected and tracked using the Greenland magnetometer chain (Friis-Christensen et al., 1988, McHenry et al., 1989). One class observed during quiet times consists of a continuous series of vortices moving generally antisunward for several hours at a time. The vortices' strength is seen to be approximately steady and neighboring vortices rotate in opposite directions. Sondrestrom radar observations show that the vortices are located at the ionospheric convection reversal boundary. Low altitude DMSP observations indicate the vortices are on field lines which map to the inner edge of the low latitude boundary layer. Because the vortices are conjugate to the boundary layer, repeat in a regular fashion and travel antisunward, it is argued that this class of vortices is caused by the Kelvin-Helmholtz instability of the inner edge of the magnetospheric boundary layer.

Mchenry, Mark A.↗
NASA NTRS1987

A boundary layer model for magnetospheric substorms

An alternative framework for understanding magnetospheric substorm activity is presented. It is argued that observations of magnetic field and plasma flow variations in the magnetotail can be explained in terms of the passage of the plasma sheet boundary layer over the satellite detecting the tail signatures. It is shown that field-aligned currents and particle acceleration processes on magnetic field lines threading the ionospheric Harang discontinuity lead to the distinctive particle and field signatures observed in the magnetotail during substorms. It is demonstrated that edge effects of field-aligned currents associated with the westward traveling surge can lead to the negative B(z) perturbations observed in the tail that are presently attributed to observations made on the anti-earthward side of a near-earth neutral line. Finally, it is shown that the model can provide a physical explanation of both the driven system and the loading-unloading system whose combined effects provide the observed substorm perturbation pattern in the magnetosphere and ionosphere.

Rostoker, Gordon↗
NASA NTRS1982

Flight and wind-tunnel correlation of boundary-layer transition on the AEDC transition cone

Transition and fluctuating surface pressure data were acquired on a 10 deg included angle cone, using the same instrumentation and technique over a wide range of Mach and Reynolds numbers in 23 wind tunnels and in flight. Transition was detected with a traversing pitot-pressure probe in contact with the surface. The surface pressure fluctuations were measured with microphones set flush in the cone surface. Good correlation of end of transition Reynolds number RE(T) was obtained between data from the lower disturbance wind tunnels and flight up to a boundary layer edge Mach number, M(e) = 1.2. Above M(e) = 1.2, however, this correlation deteriorates, with the flight Re(T) being 25 to 30% higher than the wind tunnel Re(T) at M(e) = 1.6. The end of transition Reynolds number correlated within + or - 20% with the surface pressure fluctuations, according to the equation used. Broad peaks in the power spectral density distributions indicated that Tollmien-Schlichting waves were the probable cause of transition in flight and in some of the wind tunnels.

Fisher, D. L.↗
NASA NTRS1983

Flight and wind-tunnel correlation of boundary-layer transition on the AEDC transition cone

Transition and fluctuating surface pressure data were acquired on a 10 degree included angle cone, using the same instrumentation and technique over a wide range of Mach and Reynolds numbers in 23 wind tunnels and in flight. Transition was detected with a traversing pitot pressure probe in contact with the surface. The surface pressure fluctuations were measured with microphones set flush in the cone surface. Good correlation of end of transition Reynolds number Re (sub T) was obtained between data from the lower disturbance wind tunnels and flight up to a boundary layer edge Mach number, M (sub e) = 1.2. Above M (sub e) = 1.2, however, this correlation deteriorates, with the flight Re (sub T) being 25 to 30% higher than the wind tunnel Re (sub T) at M (sub e) = 1.6. The end of transition Reynolds number correlated within + or - 20% with the surface pressure fluctuations. Broad peaks in the power spectral density distributions indicated that Tollmien-Schlichting waves were the probable cause of transition in flight and in some of the wind tunnels.

Fisher, D. F.↗