Search NASA⌕ Search

SEARCH · Search NASA

Results for “cabin noise”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

The propeller tip vortex. A possible contributor to aircraft cabin noise

Although the assumption is generally made that cabin noise levels are governed by the transmission of propeller generated noise through the fuselage sidewall, it was postulated that the propeller wake striking the wing, in particular pressure disturbances generated downstream of the propeller by the action of the propeller tip vortex, could be strong enough to excite the aircraft structure and contribute to the cabin noise level. Tests conducted to measure the strength of the propeller tip vortex support this hypothesis. It was found that the propeller tip vortex can produce a fluctuation pressure on a simulated wing surface in the wake of a propeller that exceeds by more than 15 dB the maximum direct noise that would strike the fuselage. Wing surface response to propeller tip vortex induced excitations, and the effectiveness of this response in radiating noise to the cabin interior, must be established to assess the full significance of these results.

Miller, B. A.↗
NASA NTRS1989

Cabin noise control ground tests for UHB aircraft

Measurement and analysis procedures for cabin noise control ground tests conducted on a DC-9 aircraft test section are presented along with a summary of test results. These tests were designed to analyze the effectiveness of selected noise control treatments in reducing passenger cabin noise on aircraft with aft-mounted, advanced turboprop engines. The performance of various structural and cabin sidewall treatments is assessed, based on measurements of the resulting interior noise levels and fuselage acceleration levels under simulated advanced turboprop excitation.

Simpson, Myles A.↗
NASA NTRSDate not supplied

Development of Acoustic Mufflers for Cabin Noise Reduction in Orion Spacecraft

Controlling cabin acoustic noise levels in the Crew Module (CM) of the Orion spacecraft is critical to ensure adequate speech intelligibility, to avoid fatigue, and prevent any possibility of temporary and permanent hearing loss to the crew. The primary source of cabin noise for the on-orbit phase of the mission is from the Environmental Control and Life Support System (ECLSS) which recycles and conditions breathing air and maintains cabin pressurization through its duct network and components. Unfortunately, as a side effect, noise from the ECLSS fans propagates through theses ducts and emanate into the cabin habitable volume via the ECLSS inlet and outlets. To mitigate excessive duct-borne noise, two ECLSS mufflers have been designed to provide significant acoustic transmission loss (TL) so that the cabin noise requirements can be met. Each muffler is meant to be installed in the ducting of the ECLSS air inlet and outlet sides, respectively. Packaging constraints and tight volume requirements necessitated the mufflers to be of complex geometry and compatible with the bends of the ECLSS duct layout. To design and characterize the acoustic performance of the inlet and outlet mufflers, computational acoustic models were developed using the Finite Element Method (FEM) with 𝑤𝑎𝑣𝑒଺ vibroacoustic software. Characterization of the acoustic material and perforations in the mufflers were addressed with poroelastic theory. Once the mufflers were designed on paper and its TL predicted, prototypes of these mufflers were created using additive manufacturing. The muffler prototypes were subsequently tested for acoustic TL in the laboratory with various con-figurations of acoustic materials. Comparing the analytical predictions to the test performance yielded excellent correlation for acoustic TL and demonstrated significant broadband noise attenuation. The ECLSS mufflers are currently scheduled to be installed on the Artemis II Crew Module (CM) of the Orion spacecraft and will provide significant cabin comfort to crew during the mission.

Indranil Dandaroy↗
NASA NTRS1997

Quelling Cabin Noise in Turboprop Aircraft via Active Control

Cabin noise in turboprop aircraft causes passenger discomfort, airframe fatigue, and employee scheduling constraints due to OSHA standards for exposure to high levels of noise. The noise levels in the cabins of turboprop aircraft are typically 10 to 30 decibels louder than commercial jet noise levels. However. unlike jet noise the turboprop noise spectrum is dominated by a few low frequency tones. Active structural acoustic control is a method in which the control inputs (used to reduce interior noise) are applied directly to a vibrating structural acoustic system. The control concept modeled in this work is the application of in-plane force inputs to piezoceramic patches bonded to the wall of a vibrating cylinder. The goal is to determine the force inputs and locations for the piezoceramic actuators so that: (1) the interior noise is effectively damped; (2) the level of vibration of the cylinder shell is not increased; and (3) the power requirements needed to drive the actuators are not excessive. Computational experiments for data taken from a computer generated model and from a laboratory test article at NASA Langley Research Center are provided.

Kincaid, Rex K.↗
NASA NTRSDate not supplied

Evaluation of Embedded Windshield Resonators to Reduce Cabin Noise of a UAM Concept Aircraft

High cabin noise levels in UAM vehicles could affect passenger comfort, and thus passenger acceptance of this class of aircraft. As windshields will likely comprise a large percentage of the surface area of a UAM aircraft fuselage, the objective of this work was to develop a noise reduction concept suitable for a windshield. The concept aims to increase interior absorption at targeted frequencies by including a honeycomb-like array of interior facing acoustic resonators within multiple transparent layers that make up the front and side windshields. The vehicle considered was based on the NASA RVLT Lift+Cruise UAM concept, which has 7.2 m2 of front- and side-facing windshields. Statistical Energy Analysis was used to evaluate the noise reduction attributed to the inclusion of various resonator configurations. The predicted noise reduction was dependent on the resonator geometry, the quantity of resonators included, and the assumed baseline interior cabin absorption. Results from a variety of resonator configurations are shown and discussed.

flight noise↗
NASA NTRS1982

Propeller tip vortex - A possible contributor to aircraft cabin noise

Wind tunnel model tests support the hypothesis that a propeller tip vortex may subject a downstream wing surface to greater excitation than would be experienced by the aircraft fuselage side wall exposed to propeller-generated noise, ultimately transmitting this structural response to incident dynamic pressure to the cabin interior. Even if structure-borne excitations are less efficient than airborne excitations in the creation of cabin noise, the higher level of the former could still govern cabin noise levels.

Miller, B. A.↗
NASA NTRS1984

Theoretical design of acoustic treatment for cabin noise control of a light aircraft

An analytical procedure has been used to design an acoustic treatment for cabin noise control of a light aircraft. Using this approach acoustic add-on treatments capable of reducing the average noise levels in the cabin by about 17 dB from the untreated condition are developed. The added weight of the noise control package is about 2 percent of the total gross take-off weight of the aircraft. The analytical model uses modal solutions wherein the structural modes of the sidewall and the acoustic modes of the receiving space are accounted for. The additional noise losses due to add-on treatments are calculated by the impedance transfer method. The input noise spectral levels are selected utilizing experimental flight data. The add-on treatments considered for cabin noise control include aluminum honeycomb panels, constrained layer damping tape, porous acoustic materials, noise barriers and limp trim panels. To reduce the noise transmitted through the double wall aircraft windows to acceptable levels, changes in the design of the aircraft window are recommended.

Vaicaitis, R.↗
NASA NTRS2010

Cabin Noise Studies for the Orion Spacecraft Crew Module

Controlling cabin acoustic noise levels in the Crew Module (CM) of the Orion spacecraft is critical for adequate speech intelligibility, to avoid fatigue and to prevent any possibility of temporary and permanent hearing loss. A vibroacoustic model of the Orion CM cabin has been developed using Statistical Energy Analysis (SEA) to assess compliance with acoustic Constellation Human Systems Integration Requirements (HSIR) for the on-orbit mission phase. Cabin noise in the Orion CM needs to be analyzed at the vehicle-level to assess the cumulative acoustic effect of various Orion systems at the crewmember's ear. The SEA model includes all major structural and acoustic subsystems inside the CM including the Environmental Control and Life Support System (ECLSS), which is the primary noise contributor in the cabin during the on-orbit phase. The ECLSS noise sources used to excite the vehicle acoustic model were derived using a combination of established empirical predictions and fan development acoustic testing. Baseline noise predictions were compared against acoustic HSIR requirements. Key noise offenders and paths were identified and ranked using noise transfer path analysis. Parametric studies were conducted with various acoustic treatment packages in the cabin to reduce the noise levels and define vehicle-level mass impacts. An acoustic test mockup of the CM cabin has also been developed and noise treatment optimization tests were conducted to validate the results of the analyses.

Dandaroy, Indranil↗
NASA NTRS1987

All-theoretical prediction of cabin noise due to impingement of propeller vortices on a wing structure

Reported calculations of structure-borne cabin noise for a small twin engine aircraft powered by tractor propellers rely on the following three-stage methodological breakup of the problem: (1) the unsteady-aerodynamic prediction of wing lift harmonics caused by the whipping action of the vortex system trailed from each propeller; (2) the associated wing/fuselage structural response; (3) the cabin noise field for the computed wall vibration. The first part--the estimate of airloads--skirts a full-fledged aeroelastic situation by assuming the wing to be fixed in space while cancelling the downwash field of the cutting vortices. The model is based on an approximate high-frequency lifting-surface theory justified by the blade rate and flight Mach number of application. Its results drive a finite-element representation of the wing accounting for upper and lower skin surfaces, spars, ribs, and the presence of fuel. The fuselage, modeled as a frame-stiffened cylindrical shell, is bolted to the wing.

Martinez, R.↗
NASA NTRS1978

Low frequency cabin noise reduction based on the intrinsic structural tuning concept: The theory and the experimental results, phase 2

Low frequency cabin noise and sonically induced stresses in an aircraft fuselage may be reduced by intrinsic tuning of the various structural members such as the skin, stringers, and frames and then applying damping treatments on these members. The concept is also useful in identifying the key structural resonance mechanisms controlling the fuselage response to broadband random excitation and in developing suitable damping treatments for reducing the structural response in various frequency ranges. The mathematical proof of the concept and the results of some laboratory and field tests on a group of skin-stringer panels are described. In the so-called stiffness-controlled region, the noise transmission may actually be controlled by stiffener resonances, depending upon the relationship between the natural frequencies of the skin bay and the stiffeners. Therefore, cabin noise in the stiffness-controlled region may be effectively reduced by applying damping treatments on the stiffeners.

Sengupta, G.↗
NASA NTRS1983

Design of sidewall treatment of cabin noise control of a twin engine turboprop aircraft

An analytical procedure was used to predict the noise transmission into the cabin of a twin engine general aviation aircraft. This model was then used to optimize the interior A weighted noise levels to an average value of about 85 dBA. The surface pressure noise spectral levels were selected utilizing experimental flight data and empirical predictions. The add on treatments considered in this optimization study include aluminum honeycomb panels, constrained layer damping tape, porous acoustic blankets, acoustic foams, septum barriers and limp trim panels which are isolated from the vibration of the main sidewall structure. To reduce the average noise level in the cabin from about 102 kBA (baseline) to 85 dBA (optimized), the added weight of the noise control treatment is about 2% of the total gross takeoff weight of the aircraft.

Vaicaitis, R.↗
NASA NTRS1977

Methods of reducing low frequency cabin noise and sonically induced stresses, based on the intrinsic structural tuning concept

Control of low frequency interior noise has been difficult in all commercial and general aviation aircraft, since the existing sound attenuation techniques are less effective at these frequencies. Therefore low frequency cabin noise and sonically induced stresses can be reduced mainly by a proper design of the fuselage structure. For this purpose, a concept based on intrinsic tuning and damping of fuselage structural elements has been under development at Boeing for the past three years. This paper describes the results of some laboratory and field tests that were conducted for evaluation of the concept.

Sengupta, G.↗
NASA NTRS1992

MD-80 aft cabin noise control: A case history

The interior noise technology program to improve the noise environment in the aft cabin of the MD-80 twin jet aircraft is discussed. Two potential noise control treatments were identified: vibration absorber devices for the airframe and for the engine. A series of ground and flight tests using in-service aircraft was then conducted. These tests showed that the vibration absorbers for the airframe and engine decreased aircraft noise significantly.

Lang, M. A.↗
NASA NTRS1976

The impact of interior cabin noise on passenger acceptance

Based on flight test data gathered in general aviation aircraft, a composite motion-noise passenger comfort model has been developed which enables the assessment of cabin interior noise impact on passenger acceptance. Relationships between special subject responses and passenger responses are given, as well as the effect of comfort on passenger acceptance. The importance of comfort and noise on the overall passenger reaction is discussed.

Rudrapatna, A. N.↗
NASA NTRS1985

Flight investigation of cabin noise control treatments for a light turboprop aircraft

The in-flight evaluation of noise control treatments for a light, twin-engined turboprop aircraft presents several problems associated with data analysis and interpretation. These problems include data repeatability, propeller synchronization, spatial distributions of the exterior pressure field and acoustic treatment, and the presence of flanking paths. They are discussed here with regard to a specific aeroplane configuration. Measurements were made in an untreated cabin and in a cabin fitted with an experimental sidewall treatment. Results are presented in terms of the insertion loss provided by the treatment and comparison made with predictions based on laboratory measurements.

Wilby, J. F.↗
NASA NTRS1978

Helicopter cabin noise: Methods of source and path identification and characterization

Internal noise sources in a helicopter are considered. These include propulsion machinery, comprising engine and transmission, and turbulent boundary layer effects. It is shown that by using relatively simple concepts together with careful experimental work it is possible to generate reliable data on which to base the design of high performance noise control treatments.

Murray, B. S.↗
NASA NTRS1982

Cabin Noise Control for Twin Engine General Aviation Aircraft

An analytical model based on modal analysis was developed to predict the noise transmission into a twin-engine light aircraft. The model was applied to optimize the interior noise to an A-weighted level of 85 dBA. To achieve the required noise attenuation, add-on treatments in the form of honeycomb panels, damping tapes, acoustic blankets, septum barriers and limp trim panels were added to the existing structure. The added weight of the noise control treatment is about 1.1 percent of the total gross take-off weight of the aircraft.

Vaicaitis, R.↗