Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalyst coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Enhancing Oxygen Reduction Activity and Cr Tolerance of Solid Oxide Fuel Cell Cathodes by a Multiphase Catalyst Coating

Intermediate temperature solid oxide fuel cells (IT-SOFCs) are cost-effective and efficient energy conversion systems. Here, the sluggish oxygen reduction reaction (ORR) and the degradation of cathodes are critical challenges to the commercialization of IT-SOFCs. Here, a highly efficient multiphase (MP) catalyst coating, consisting of Ba 1–x Co 0.7 Fe 0.2 Nb 0.1 O 3–δ (BCFN) and BaCO 3 , to enhance the ORR activity and durability of the state-of-the-art lanthanum strontium cobalt ferrite (La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3–δ , LSCF) cathode is reported. The conformal MP catalyst-coated LSCF cathode shows a polarization resistance (R p ) of 0.048 Ω cm 2 at 650 °C, about one order of magnitude smaller than that of the bare LSCF. In an accelerated Cr-poisoning test, the degradation rate of the catalyst-coated LSCF electrode is 10 –3 Ω cm 2 h –1 (0.59% h –1 ) over 200 h, only one fifth of the degradation rate of the bare LSCF electrode at 750 °C. In addition, anode-supported single cells with the MP catalyst-coated LSCF cathode show a dramatically enhanced peak power density (1.4 W cm –2 vs 0.67 W cm –2 at 750 °C) and increased durability against Cr and H 2 O. Both experimental results and density functional theory-based calculations indicate that the BCFN phase improves the ORR activity while the BaCO 3 phase enhances the stability of the LSCF cathode.

solid oxide fuel cells↗
DOE OSTI2025

Anion Exchange Membrane Water Electrolysis Using a Catalyst-Coated Membrane Cathode

A catalyst-coated membrane (CCM) approach to electrode fabrication for high pH water electrolysis offers enhanced interfacial contact between the catalyst layer and the membrane surface in comparison to the catalyst-coated substrate (CCS) electrode configuration. The CCM facilitates enhanced ionic and water transport between the cathode and the anion exchange membrane (AEM). This advantage is particularly significant with AEM water electrolysis (compared to proton exchange membrane water electrolysis) because the cathode typically operates under dry conditions and relies solely on diffusive water transport across the AEM from the liquid-fed anode. This study presents a direct performance comparison between CCS and CCM cathode configurations using identical hydrogen evolution reaction (HER) catalysts and other components. The use of a pseudo-reference electrode integrated into the membrane electrode assembly enabled detailed analysis of the CCM cathode polarization behavior. Surface characterization provided insight into the degradation mechanisms associated with the CCM configuration. Optimization of the cathode ionomer cross-link density improved both the cathode polarization performance and the electrolysis device durability. Further optimization of the HER catalyst loading in the CCM cathode resulted in additional gains in the electrolysis efficiency. Collectively, these findings offer valuable guidance for the design and fabrication of high-performance, durable AEM electrolysis CCMs.

Water electrolysis↗
DOE OSTI2020

Roll-to-roll production of catalyst coated membranes for low-temperature electrolyzers

Here we demonstrate a roll-to-roll (R2R) process for direct coating of anode catalyst layers on a polymer electrolyte membrane for low-temperature water electrolysis. To develop this process, we studied catalyst ink formulation, ink-membrane interactions, and coating quality. The catalyst inks were a mixture of iridium oxide (IrO2) and Nafion in a water and alcohol dispersion medium. The type of alcohol (methanol, ethanol, propanols) and water-to-alcohol ratio were varied to determine their influence on membrane swelling, dispersion quality, and coatability. Interactions of the ink dispersion medium with the membrane were characterized using sessile-drop contact-angle measurements. These measurements show that the ratio of water to alcohol has a strong influence on how rapidly the dispersion media is absorbed by the membrane. Rheology of the catalyst inks was measured to understand the microstructure of the catalyst particles in the ink. This analysis found that 1-propanol leads to better dispersion of the IrO2 particles than ethanol. Small-scale coating samples were prepared to understand coating uniformity and formation of irregularities. Subsequently, two water/1-propanol ratios (90:10 and 75:25) were down-selected for large-scale R2R slot die coating. The R2R catalyst-coated membrane (CCM) coating process increased catalyst layer production throughput by over 500x compared to our standard lab-scale spray coating. The CCMs obtained from this process were tested as single-cell membrane electrode assemblies. They exhibited a cell voltage of 1.91 V at a current density of 2 A/cm2, which is comparable to spray-coated CCMs. In conclusion, the work presented here demonstrates a continuous, scalable manufacturing process that eliminates the need for the decal transfer step typically used in CCM production.

42 ENGINEERING↗
DOE OSTI2022

Low-Cost, High Performance Catalyst Coated Membranes for PEM Water Electrolyzers (Final Technical Report)

In this project, the objective was to develop reduced-cost manufacturing techniques capable of producing proton exchange membrane water electrolyzer (PEMWE) catalyst coated membranes (CCMs) with further improved performance relative to then-current 3M CCM technology. Processes to be developed would enable 1) production of 0.5 m wide CCMs (approximately 2x wider than produced by the current laboratory/pilot-scale processes) and 2) 3x higher net-effective linear rates (lineal-meters of CCM produced per cumulative process time) than the baseline CCM process. In combination, the wider width CCM and increased net-effective linear rates would result in a 6-fold decrease in CCM manufacturing cost (defined as cumulative machine and labor time) per m 2 of CCM produced. PEMWE CCMs produced with these optimized processes were targeted to produce 1) 0.25 A/cm 2 or greater at 1.5 V, 2) 2.0 A/cm 2 or greater at 1.75 V and 3) 4 A/cm 2 or greater at 1.95V, 4) with total catalyst platinum-group metal (PGM) loadings of ≤ 0.50 mg/cm 2 , measured in a cell with 50 cm 2 active area (or larger) at 80°C cell temperature and ambient outlet pressures.

08 HYDROGEN↗
DOE OSTI2021

Catalyst coating of a perovskite film and particles exsoluted from the perovskite film

A hybrid catalyst coating composed of a conformal thin film with exsoluted PrOx nano-particles. The conformal PNM thin film can be a perovskite composition of PrNi0.5Mn0.5O3 (PNM). The PrOx nano-particles dramatically enhance the oxygen reduction reaction kinetics via a high concentration of oxygen vacancies while the thin PNM film effectively suppresses strontium segregation from the cathode of an intermediate-temperature solid oxide fuel cell.

Liu, Meilin↗
DOE OSTI2020

Optimization of catalyst-coated membranes for enhancing performance in proton exchange membrane electrolyzer cells

To achieve large-scale application of proton exchange membrane electrolyzer cells (PEMECs) for hydrogen production, it is highly desirable to reduce the manufacturing cost while enhancing cell performance. In the PEMPECs, a catalyst-coated membrane (CCM) is the vital component where electrochemical reactions and mass transport mainly occur. The fabrication methods and catalyst layer (CL) structure can significantly affect the cell performance. Herein, for the first time, a comparative study of CCM fabrications with decal transfer and direct spray deposition methods have been conducted by both ex-situ materials characterization and in-situ performance testing in PEMECs. It is found CCMs that are fabricated with a direct spray deposition method display enhanced cell performance compared to CCMs fabricated with a decal transfer method, mainly due to the largely reduced ohmic resistance and improved mass transport. More importantly, cell performance can be greatly enhanced by simply regulating the Nafion ionomer content at the anode CL. The optimal Nafion ionomer content of 10 wt% gives the best cell performance at 80 °C with a low cell voltage of 1.887 V at 2 A cm -2 , outperforming the commercial CCM and most other previous publications. Our study provides a valuable guidance for fabrication and optimization of CCMs with significantly enhanced performance and reduced cost for practical application of the PEMECs.

08 HYDROGEN↗
DOE OSTI2026

Hybrid Ionomer-Free Porous Transport Electrodes With Catalyst Coated Membranes for Enhanced Water Electrolysis

To promote industrial uptake of clean hydrogen production technologies such as polymer electrolyte membrane (PEM) water electrolyzers, advancements in catalyst layer (CL) morphology are required. We demonstrate how improved electrochemical performance can be achieved when using an ionomer free porous transport electrode (PTE) coupled with a traditional catalyst coated membrane (CCM) assembly in PEM water electrolyzers. Notably, we reveal that the superior performance achieved when utilizing a hybrid PTE and CCM assembly is due to enhanced ohmic performance caused by optimal contact with both the porous transport layer (PTL) and PEM interfaces. Using operando neutron radiography, we demonstrate that configurations utilizing a CCM resulted in more rapid water replenishment to reaction sites, indicating enhanced membrane hydration beneficial for performance. This enhanced membrane hydration coupled with improved contact area at the PEM-catalyst layer (CL) and PTL-CL interfaces was revealed through the reduced ohmic overpotentials of the hybrid PTE-CCM design, which achieved the lowest ohmic overpotential of 431 mV at 2000 mA cm−2. While the average in-plane water distributions are generally similar between cell configurations, we reveal that utilizing a PTE configuration promotes a more homogenous water distribution near the CL-membrane interface due to enhanced catalyst utilization.

Seip, Tess [ORNL] (ORCID:0000000232740594)↗
DOE OSTI2023

The effect of ink ball milling time on interparticle interactions and ink microstructure and their influence on crack formation in rod-coated catalyst layers

This work investigates the influence of ballmilling (sometimes also referred to as jar roller milling) time on cathode catalyst layer (CL) inks and electrode properties using formulations and coating methods relevant for industrial manufacturing. Four CL inks with the same composition were milled for 24, 48, 72, or 96 h. Rheological investigation of these inks showed a reduction of elastic moduli and steady-shear viscosity with continuous ink milling, which is correlated to a decrease in particle-particle interactions as well as formation of smaller agglomerates. Optical microscopy (OM) analysis of the fabricated electrodes revealed a trend in surface crack formation; formulations milled for 24 h contained the lowest average surface crack area percentages of 0.370% at heavy-duty loadings of ~0.300 mg Pt cm -2 , compared to 2.418% for the ink milled for 96 h. Further characterization of the CL through transmission electron microscopy (TEM) imaging showed a decrease in the mean agglomerate and pore size with milling time. Furthermore, these smaller electrode features were consistent with reduced fracture resistance and, hence, development of larger stresses during drying. Our results highlight the need to consider ink processing as an important component in defect-free CL manufacturing.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Roll-to-Roll Direct Coating of Catalyst Inks on Membrane Films: Progress and Challenges

Further development of low temperature electrolysis (LTE) systems is of importance to ensure the renewable hydrogen production for hydrogen-based energy systems. The membrane electrode assembly (MEA) is a key component of the LTE system and typically contains a catalyst coated membrane (CCM). To enable the U.S. Department of Energy's hydrogen production cost goal of $2/kg, high volume manufacturing processes will be required to lower manufacturing costs of the CCM. A promising way for high-throughput manufacturing of CCM is using roll-to-roll (R2R) methods that allow the direct coating of electrodes on membrane films. However, there are many challenges with this methodology, both in the coating process as well as with web handling. In this talk, we discuss the membrane-ink interaction by evaluating the solvent uptake of a Nafion membrane system and verify the coatability of various inks through lab-scale coatings onto this system. Furthermore, rheology and surface tension data of the ink will be discussed together with the resulting morphology of the coated electrodes. The R2R-processed CCMs will finally be analyzed using electrochemical performance data and the results put in context with the challenges that the mass production of CCMs for LTE system faces to date.

39 EE - Hydrogen and Fuel Cell Technologies (EE-3F↗
DOE OSTI2022

Synthesis and Characterization of Mesoporous Silica Nanoparticles Loaded with Pt Catalysts

Coating the catalyst with a nanoporous layer has been demonstrated to be an effective approach to improve catalyst stability. Herein, we systematically investigate two types of core-shell mesoporous silica nanoparticles with a platinum nanocatalyst using a variety of characterization methods. One of the mesoporous particles has a unique amine ring structure in the middle of a shell (Ring-mSiO 2 /Pt-5.0/SiO 2 ), and the other one has no ring structure (mSiO 2 /Pt-5.0/SiO 2 ). Brunauer–Emmett–Teller/Barrett–Joyner–Halenda (BET/BJH) presented a similar surface area for both particles, and the pore size was 2.4 nm. Ultra-Small-Angle X-ray Scattering (USAXS)/ Small-Angle X-ray Scattering (SAXS) showed the size of mSiO 2 /Pt-5.0/SiO 2 and Ring-mSiO 2 /Pt-5.0/SiO 2 were 420 nm and 272 nm, respectively. It also showed that the ring structure was 30 nm above the silica core. Using high-resolution Transmission Electron Microscopy (TEM), it was found that the platinum nanoparticles are loaded evenly on the surface of the silica. In situ SAXS heating experiments and Thermogravimetric Analysis (TGA) indicated that the mSiO 2 /Pt-5.0/SiO 2 were more stable during the high temperature, while the Ring-mSiO 2 /Pt-5.0/SiO 2 had more change in the particle.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Understanding the effect of organic coatings on 4-nitrostyrene hydrogenation selectivity over Pt/TiO 2 catalysts

The hydrogenation of 4-nitrostyrene was investigated over Pt/TiO 2 catalysts to understand the effects of different catalyst coatings on product selectivity and reaction rates. This reaction is a much-investigated selectivity probe due to difficulty in controlling reactivity between the nitro and vinyl groups of 4-nitrostyrene, with C=C reduction generally being more favorable. 4-Nitrostyrene hydrogenation reactions were carried out in a batch reactor using uncoated, organothiol coated, phosphonic acid (PA) coated, and ion-conducting polymer (ionomer) coated catalysts. Thiols form dense coatings on Pt surfaces, whereas PAs preferentially accumulate on TiO 2 ; ionomer binding preference is unknown for this type of catalyst. The coating densities of the thiols and PAs were varied to observe the effects of loading on catalytic activity and reaction selectivity relative to the uncoated catalyst. Changes in selectivity were observed for catalysts with all coatings, with thiol coatings shifting selectivity towards the nitro reduction product, 4-vinylaniline (4-VA), and both ionomer and PA coatings shifting towards 4-ethylnitrobenzene, the olefin hydrogenation product. It was observed that selectivity toward 4-VA increased with thiol coating density, where 1,2-benzenedithiol (BDT) coated catalysts exhibited a selectivity of >99%. These changes were attributed to the identity of the adsorption sites blocked by the different coatings: blocking of metal sites via thiols decreased the rate of C=C hydrogenation, whereas blocking of TiO 2 sites by PAs decreased the rate of nitro group hydrogenation. The changes observed for ionomer and PA coatings suggested that ionomers, like PAs, bind preferentially to the metal oxide support rather than the active metal. This work provides new support to the proposal that nitro group hydrogenation preferentially occurs on TiO 2 sites after hydrogen spillover and underscores how selection of ligand functionality can be used to tune catalyst selectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Enhanced Catalyst Durability and Sulfur Tolerance by Atomic Layer Deposition (CRADA Final Report)

This CRADA advanced the use of atomic layer deposition (ALD) catalyst coatings to improve sulfur tolerance and demonstrate improved catalyst durability for biomass conversion chemistries. This project leveraged National Laboratory and industry expertise for ALD catalyst coating development between NREL, ALD NanoSolutions, Inc. ("ALD NanoSolutions"), and Johnson Matthey PLC ("Johnson Matthey"). To better understand the role of ALD coatings on catalyst activity and durability, a joint experimental and computational effort combined bench-scale ALD catalyst synthesis, material characterization, catalyst testing, and modeling of catalyst surface energetics. In addition, to demonstrate the commercial relevance of this technology, scaled ALD coated catalysts were subjected to continuous testing and accelerated aging to validate performance gains. Results were used to inform ALD catalyst coating manufacturing cost models, as well as biobased chemical process cost models.

09 BIOMASS FUELS↗
DOE OSTI2023

Towards improved conversion of wet waste to jet fuel with atomic layer deposition-coated hydrodeoxygenation catalysts

The conversion of wet waste-derived volatile fatty acids into jet fuel-range hydrocarbons is a promising route for increasing the production of sustainable aviation fuel; however, the cost and moderate alkane selectivity of Pt-based hydrodeoxygenation catalysts present challenges for commercialization. Here, to address this, we used atomic layer deposition to apply TiO 2 overcoats to Pt/Al 2 O 3 catalysts and create new interface sites that exhibited 8 times higher site time yield of the desirable n-alkane product than uncoated catalyst. Through TPR/TPD, XPS, CO DRIFTS, and DFT calculations, we found that the increased selectivity of the ALD-coated catalyst was due to the creation of O vacancies at the Pt-TiO 2 interface under reducing conditions, resulting in new Ti 3+ acid sites near the active metal. Maximum conversion and alkane selectivity during HDO was achieved with an ALD-coated 0.5% wt Pt catalyst, indicating that TiO 2 ALD can be used to maximize the utility of precious-metal catalysts.

09 BIOMASS FUELS↗
DOE OSTI2023

Advanced electrode manufacturing to enable low cost PEM electrolysis

A critical challenge for the implementation of proton exchange membrane (PEM)-based water electrolyzers for the H2@Scale vision is the capital cost, which is largely driven by related factors of overdesign and highly manual legacy manufacturing methods. Typical electrolyzer cells have an order of magnitude higher membrane thickness and catalyst loading vs. fuel cells, in part because the manufacturing methods being used are not capable of producing uniform and reliable electrodes on thin membranes with low loading. Advanced electrode manufacturing is therefore the key enabler to reduce the cost of the electrolyzer stack, particularly roll-to-roll (R2R) manufacturing of catalyst coated layers (CCLs) and catalyst coated membranes (CCMs). The electrolyzer manufacturing process still relies on traditional sheet-to-sheet (S2S) processes, which requires intensive labor to make parts to meet the specification requirements. This project leverages fuel cell expertise (GM) with Proton’s knowledge of electrolyzer components to develop the electrocatalyst ink formulations and coating processes using slot die (ORNL) and gravure (NREL) coatings, with proof of concept at the pilot-scale (Kodak).

08 HYDROGEN↗
NASA NTRS2010

Sol-gel based oxidation catalyst and coating system using same

An oxidation catalyst system is formed by particles of an oxidation catalyst dispersed in a porous sol-gel binder. The oxidation catalyst system can be applied by brush or spray painting while the sol-gel binder is in its sol state.

Watkins, Anthony N.↗
NASA NTRS2010

Sol-gel based oxidation catalyst and coating system using same

An oxidation catalyst system is formed by particles of an oxidation catalyst dispersed in a porous sol-gel binder. The oxidation catalyst system can be applied by brush or spray painting while the sol-gel binder is in its sol state.

Watkins, Anthony N.↗