Vaporization of chromium oxides from the surface of TD-NiCr under oxidizing conditions
Vaporization of chromium oxides from surface of TD-NiCr under oxidizing conditions
Kohl, F. J.↗
SEARCH · Search NASA
Results for “chromium oxide”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Chromium oxide coatings improve thermal emissivity of alumina
Chromium oxide coatings improve thermal radiation characteristics of alumina-coated heater-cathode systems in vacuum tubes. Chromium oxide is applied either as a surface layer or as a doping material. The new coatings eliminate the high temperature migration problems of carbon surface treatments.
Upshaw, V.↗
Development of RF sputtered chromium oxide coating for wear application
The radio frequency sputtering technique was used to deposite a hard refractory, chromium oxide coating on an Inconel X-750 foil 0.1 mm thick. Optimized sputtering parameters for a smooth and adherent coating were found to be as follows: target-to-substrate spacing, 41.3 mm; argon pressure, 5-10 mTorr; total power to the sputtering module, 400 W (voltage at the target, 1600 V), and a water-cooled substrate. The coating on the annealed foil was more adherent than that on the heat-treated foil. Substrate biasing during the sputter deposition of Cr2O3 adversely affected adherence by removing naturally occurring interfacial oxide layers. The deposited coatings were amorphous and oxygen deficient. Since amorphous materials are extremely hard, the structure was considered to be desirable.
Bhushan, B.↗
Evaluation of chromium oxide and molybdenum disulfide coatings in self-acting stops of an air-lubricated Rayleigh step thrust bearing
Two coatings for a Rayleigh step thrust bearing were tested when coasting down and stopping under self-acting operation in air. The thrust bearing had an outside diameter of 8.9 cm (3.5 in.), an inside diameter of 5.4 cm (2.1 in.), and nine sectors. The load was 73 N (16.4 lbf). The load pressure was 19.1 kN/per square meter (2.77 lbf/per square inch) on the total thrust bearing area. The chromium oxide coating was good to 150 stops without bearing deterioration, and the molybdenum disulfide coating was good for only four stops before bearing deterioration. The molybdenum disulfide coated bearing failed after nine stops.
Nemeth, Z. N.↗
Bifacial CdTe Solar Cells with Copper Chromium Oxide Back-Buffer Layer
Bifacial solar cells have the potential to maintain energy output higher than monofacial devices under unfavorable weather conditions. A transparent back-buffer layer which can passivate the interface and improve the minority carrier lifetime is critical in CdTe-based bifacial devices. Herein, solution-processed Cu x Cr y O z as a promising back-buffer for CdTe/CdS solar cells is demonstrated. The carrier lifetimes measured at the front and back of the device are 31.2 and 3.1 ns, respectively, which correspond to an increase of ≈38% and 138%, respectively, compared to the reference device. This dramatic improvement in lifetime results in a 100% increase in short-circuit current measured with backside illumination. The best bifacial device has efficiencies 7.6% and 12.5%, respectively, from back and front illumination, yielding a bifaciality factor of 0.60.
14 SOLAR ENERGY↗
Elucidation of puzzling questions regarding the CrO x /Al 2 O 3 catalyst I. X-ray absorption spectroscopy aided identification of the nature of the chromium oxide species in the CrO x /Al 2 O 3 dehydrogenation catalyst system
The CATOFIN© process produces propylene from propane using a CrO x /Al 2 O 3 catalyst. Despite its use, there are still uncertainties surrounding the nature of Cr species formed during synthesis, regeneration, and aging. It has been observed that ppm levels of Cr 2 O 3 can be oxidized to Cr(VI) in air; however, when Cr 2 O 3 is in direct contact with Al 2 O 3 , Cr(VI) formation increased more than 100-fold. Here, to confirm physical contact between Cr 2 O 3 and Al 2 O 3 results in increased Cr(VI) formation, Cr 2 O 3 and Cr 2 O 3 /Al 2 O 3 samples were synthesized, calcined, and characterized. Catalytic activity measurements confirm propylene selectivity inversely tracks with Cr(VI). Wet chemical titration and X-ray absorption spectroscopy (XAS) quantified and determined the structure of the Cr(VI) species. FEFF X-ray absorption near edge structure simulations determined the potential sensitivity of the XAS to the presence of Al 3+ /Cr 3+ neighboring atoms. XAS correlated to FEFF simulations suggested that Al 3+ x Cr 3+ 2–x Cr 6+ 3 O 12 comprises a significant fraction of the Cr(VI) species formed.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Self-Lubricating Composite Containing Chromium Oxide
A self lubricating. friction and wear reducing composite material useful over a wide temperature range of from cryogenic temperature up to about 900 C. contains 60 80 wt. % of particulate Cr2O3, dispersed in a metal binder of a metal alloy containing Cr and at least 50 wt. % of Ni, Cr or a mature of Ni and Cr. It also contains 5-20 wt. % of a fluoride of at least one Group I, Group II or rare earth metal and. optionally, 5-20 wt. % of a low temperature lubricant metal, such as Ag. Au, Pt, Pd, Rh and Cu. This composite exhibits less oxidation instability and less abrasiveness than composites containing chromium carbide, is readily applied using plasma spray and can be ground and polished with a silicon carbide abrasive.
Dellacorte, Christopher↗
The x ray microprobe determination of chromium oxidation state in olivine from lunar basalt and kimberlitic diamonds
The synchrotron x-ray microprobe is being used to obtain oxidation state information on planetary materials with high spatial resolution. Initial results on chromium in olivine from various sources including laboratory experiments, lunar basalt, and kimberlitic diamonds are reported. The lunar olivine was dominated by Cr(2+) whereas the diamond inclusions had Cr(2+/Cr(3+) ratios up to about 0.3. The simpliest interpretation is that the terrestrial olivine crystallized in a more oxidizing environment than the lunar olivine.
Sutton, S. R.↗
Vibrational sum frequency generation spectroscopy reveals the inertness of chromium oxide (001) surfaces
Nanoengineered metal oxides such as Cr(III)-oxide (chromia) films have diverse potential applications in corrosion inhibition, remediation, energy generation, catalysis, data storage, and biological and environmental systems. Concerns about material degradation or oxidation to toxic chromate necessitate an understanding of chromia/aqueous interfaces, beginning with their hydroxylation and hydration behavior. Vibrational sum-frequency generation spectroscopy (vSFG) provides specific molecular-level information about water at the oxide/aqueous junction with high surface selectivity. To overcome the strong absorber problem typical of certain metal oxides in the UV–visible range during nonlinear optical studies, we employed molecular beam epitaxy to deposit transparent, epitaxial nanofilms of Cr 2 O 3 with (001) crystalline orientation on sapphire (Al 2 O 3 (001)) substrates, as confirmed by atomic force microscopy and X-ray diffraction. vSFG spectra of the air and water interfaces of the Cr 2 O 3 (001) films reveal hydroxyl features corresponding to both dissociated and molecular water on the surface. In contrast to the dangling hydroxyls found on the bare Al 2 O 3 (001) substrate, the hydroxyl groups on the deposited Cr 2 O 3 (001) nanofilm do not readily undergo isotopic H/D exchange when exposed to varying forms of D 2 O under ambient conditions. When considering the chemistries of the corresponding trivalent cations in aqueous solution, the finding is at variance with their similar acidities and proton exchange dynamics but consistent with markedly slower inner-sphere water ligand exchange of hexaquo Cr 3+ . This finding challenges the idea that proton and water exchange at the water/Cr₂O₃(001) interface are solely correlated, driven by the strength of metal-bridging oxygen bonds and surface hydroxyl distribution, without direct causation.
Boamah-Agyemang, Mavis D. [Pacific Northwest Natio↗
Chromium Oxidation State in Planetary Basalts: Oxygen Fugacity Indicator and Critical Variable for Cr-Spinel Stability
Cr is a ubiquitous and relatively abundant minor element in basaltic, planetary magmas. At the reduced oxidation states (<FMQ) of many planetary basalts Cr is present in melts as both divalent and trivalent forms. The ratio of trivalent to divalent Cr present in the melt has many consequences for the stability and Cr concentration of magmatic phases such as spinel, clinopyroxene, and olivine. However, understanding the Cr valence in quenched melts has historically been plagued with analytical issues, and only recently has reliable methodology for quantifying Cr valence in quenched melts been developed. Despite this substantial difficulty, the pioneering works of Hanson and Jones and Berry and O'Neill provided important insights into the oxidation state of Cr in in silicate melts. Here we present a series of 1-bar gas mixing experiments performed with a Fe-rich basaltic melt in which have determined the Cr redox ratio of the melt at over a range of fO2 values by measuring this quantity in olivine with X-ray Absorption Near Edge Spectroscopy (XANES). The measured Cr redox ratio of the olivine phenocrysts can be readily converted to the ratio present in the conjugate melt via the ratio of crystal-liquid partition coefficients for Cr3+ and Cr2+. We have applied these results to modeling Cr spinel stability and Cr redox ratios in a primitive, iron-rich martian basalt.
Bell, A. S.↗
Enhancement of oxidative vaporization of chromium (III) oxide and chromium by oxygen atoms
Rates of oxidative vaporization of Cr2O3 were found to be markedly enhanced in the presence of O atoms. Investigations were conducted over the temperature range 470 to 1520 K. For Cr2O3 the enhancement was about 10 to the 9th power at 820 K in oxygen containing 2.5 percent atoms. Rapid oxidative vaporization of bare chromium was observed below 1070 K, the rate being about one-half that of Cr2O3. Results are interpreted in terms of thermochemical analysis.
Fryburg, G. C.↗
Selected fretting-wear-resistant coatings for titanium - 6-percent-aluminum - 4-percent-vanadium alloy
A titanium - 6-percent-aluminum - 4-percent-vanadium alloy (Ti-6Al-4V) was subjected to fretting-wear exposures against uncoated Ti-6Al-4V as a baseline and against various coatings and surface treatments applied to Ti-6Al-4V. The coatings evaluated included plasma-sprayed tungsten carbide with 12 percent cobalt, aluminum oxide with 13 percent titanium oxide, chromium oxide, and aluminum bronze with 10 percent aromatic polyester; polymer-bonded polyimide, polyimide with graphite fluoride, polyimide with molybdenum disulfide (MoS2), and methyl phenyl silicone bonded MoS2, preoxidation surface treatment, a nitride surface treatment, and a sputtered MoS2 coating. Results of wear measurements on both the coated and uncoated surfaces after 300,000 fretting cycles indicated that the polyimide coating was the most wear resistant and caused the least wear to the uncoated mating surface.
Bill, R. C.↗
Oxidative vaporization kinetics of chromium (III) oxide in oxygen from 1270 to 1570 K
Rates of oxidative vaporization of Cr2O3 on preoxidized resistively heated chromium were determined in flowing oxygen at 0.115 torr for temperatures from 1270 to 1570 K. Reaction controlled rates were obtained from experimental rates by a gold calibration technique. These rates were shown to agree with those predicted by thermochemical analysis. The activation energy obtained for the oxidative vaporation reaction corresponded numerically with the thermochemical enthalpy of the reaction. A theoretical equation is given for calculating the rate from thermodynamic data by using boundary layer theory.
Stearns, C. A.↗
Auger electron spectroscopy and depth profile study of oxidation of modified 440C steel
Auger electron spectroscopy (AES) and sputtering were used to study selective oxidation of modified 440C steel. The sample was polycrystalline. Oxidation was performed on initially clean surfaces for pressures ranging from 1 x 10 to the minus 7th power to 1 x 10 to the minus 5th power torr and temperatures ranging from room temperature to 800 C. AES traces were taken during oxidation. In situ sputtering depth profiles are also obtained. A transition temperature is observed in the range 600 to 700 C for which the composition of the outer surface oxide changed from iron oxide to chromium oxide. Heating in vacuum about 5 x 10 to the minus 10 power torr to 700 C causes conversion of the iron oxide surface to chromium oxide.
Ferrante, J.↗
The Effects of Mixing Multi-Component HLW Glasses on Spinel Crystal Size
The Hanford Waste Treatment and Immobilization Plant will vitrify radioactive waste into borosilicate glass. The high-level waste (HLW) glass formulations are constrained by processing and property requirements, including restrictions aimed at avoiding detrimental impacts of spinel crystallization in the melter. To understand the impact of glass chemistry on crystallization, two HLW glasses precipitating small (?5 µm) spinel crystals were individually mixed with a glass that precipitated large (?45 µm) spinel crystals in ratios of 25, 50, and 75 wt%. The size of spinel crystals in the mixed glasses varied from 5 to 20 µm. Small crystal size was attributed to: (1) high concentrations of nuclei due to the presence of ruthenium oxide and (2) chromium oxide aiding high rates of nucleation. Results indicate that the spinel crystal size can be controlled using chromium oxide and/or noble metal concentrations in the melt, even in complex mixtures like HLW glasses. Small crystals tend to settle slowly, so they are acceptable in the melter without a risk of failure. Allowing higher concentrations of spinel-forming waste components in the waste glass enables glass compositions with higher waste loading, thus increasing plant operational flexibility. An additional benefit to the presence of chromium oxide in the glass composition is the potential for the oxide to protect melter walls against corrosion.
Lonergan, Charmayne E.↗
Process for the production of star-tracking reticles
Reticles designed with quartz bases are masked with desired pattern and then are coated with highly adherent layers of chromium, chromium silver alloy, silver, copper, and black chromium (mixture of chromium and chromium oxides). Black chromium final layer produces required nonreflective surface.
Toft, A. R.↗
Oxidation-resistant cermet
Chromium metal alloys and chromium oxide ceramic are combined to produce cermets with oxidation-resistant properties. Application of cermets includes use in hot corrosive environments requiring strong resistive materials.
Phillips, W. M.↗