Search NASA⌕ Search

SEARCH · Search NASA

Results for “circuit model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Circuit model for characterizing the nearly linear behavior of avalanche diodes in amplifier circuits

A nonlinear circuit model for avalanche diodes is proposed. The model was derived by assuming that the bias dependence of the elements in a known small-signal equivalent-circuit model for existing diodes arises in a manner consistent with the theory of an idealized Read-type device. The model contains a nonlinear R-L branch, a controlled source, and a linear depletion capacitance. The model is used in the nearly linear sense to predict intermodulation distortion and gain compression in avalanche diode amplifiers. Computed results for amplifiers with existing diodes are shown to be in good agreement with experiment.

Penfield, P., Jr.↗
NASA NTRS2004

Magnetic Circuit Model of PM Motor-Generator to Predict Radial Forces

A magnetic circuit model is developed for a PM motor for flywheel applications. A sample motor is designed and modeled. Motor configuration and selection of materials is discussed, and the choice of winding configuration is described. A magnetic circuit model is described, which includes the stator back iron, rotor yoke, permanent magnets, air gaps and the stator teeth. Iterative solution of this model yields flux linkages, back EMF, torque, power, and radial force at the rotor caused by eccentricity. Calculated radial forces are then used to determine motor negative stiffness.

McLallin, Kerry↗
NASA NTRS1989

A circuit model for filament eruptions and two-ribbon flares

A circuit model is derived for solar filament eruptions and two-ribbon flares. In the model the filament is approximated as a line current and the current sheet as infinitely thin. The model reproduces the slow energy buildup and eruption of the filament and the energy dissipation in a current sheet at the top of postflare loops during the two-ribbon flare. The two circuits considered are that of the filament and its return current and that of the current sheet and its return current. These circuits are inductively coupled, and free energy stored in the filament in the pre-flare phase is found to be transferred to the sheet during the impulsive phase and rapidly dissipated there. In the solutions for the evolution of the filament current sheet system four phases are distinguished: (1) a slow energy buildup, (2) a 'metastable' state, (3) the eruptive phase, and (4) a postflare phase. These phases are described in detail.

Martens, P. C. H.↗
NASA NTRS1997

Validation of an Accurate Three-Dimensional Helical Slow-Wave Circuit Model

The helical slow-wave circuit embodies a helical coil of rectangular tape supported in a metal barrel by dielectric support rods. Although the helix slow-wave circuit remains the mainstay of the traveling-wave tube (TWT) industry because of its exceptionally wide bandwidth, a full helical circuit, without significant dimensional approximations, has not been successfully modeled until now. Numerous attempts have been made to analyze the helical slow-wave circuit so that the performance could be accurately predicted without actually building it, but because of its complex geometry, many geometrical approximations became necessary rendering the previous models inaccurate. In the course of this research it has been demonstrated that using the simulation code, MAFIA, the helical structure can be modeled with actual tape width and thickness, dielectric support rod geometry and materials. To demonstrate the accuracy of the MAFIA model, the cold-test parameters including dispersion, on-axis interaction impedance and attenuation have been calculated for several helical TWT slow-wave circuits with a variety of support rod geometries including rectangular and T-shaped rods, as well as various support rod materials including isotropic, anisotropic and partially metal coated dielectrics. Compared with experimentally measured results, the agreement is excellent. With the accuracy of the MAFIA helical model validated, the code was used to investigate several conventional geometric approximations in an attempt to obtain the most computationally efficient model. Several simplifications were made to a standard model including replacing the helical tape with filaments, and replacing rectangular support rods with shapes conforming to the cylindrical coordinate system with effective permittivity. The approximate models are compared with the standard model in terms of cold-test characteristics and computational time. The model was also used to determine the sensitivity of various circuit parameters including typical manufacturing dimensional tolerances and support rod permittivity. By varying the circuit parameters of an accurate model using MAFIA, these sensitivities can be computed for manufacturing concerns, and design optimization previous to fabrication, thus eliminating the need for costly experimental iterations. Several variations were made to a standard helical circuit using MAFIA to investigate the effect that variations on helical tape and support rod width, metallized loading height and support rod permittivity, have on TWT cold-test characteristics.

Kory, Carol L.↗
NASA NTRS2005

Equivalent Circuit Modeling for Carbon Nanotube Schottky Barrier Modulation in Polarized Gases

We study the carbon nanotube Schottky barrier at the metallic electrode interface in polarized gases using an equivalent circuit model. The gas-nanotube interaction is often weak and very little charge transfer is expected [l]. This is the case with'oxygen, but the gas-electrode interaction is appreciable and makes the oxygen molecules negatively charged. In the closed circuit condition, screening positive charges appear in the nanotube as well as in the electrode, and the Schottky barrier is modulated due to the resultant electrostatic effects [2]. In the case of ammonia, both the gas-nanotube and gas-electrode interactions are weak, but the Schottky barrier can still be modulated since the molecules are polarized and align in the preferred orientation within the gap between the electrode and nanotube in the open circuit condition (dipole layer formation). In the closed circuit condition, an electric field appears in the gap and strengthens or weakens the preferred dipole alignment reflecting the nanotube Fermi level. The modulation is visible when the nanotube depletion mode is involved, and the required dipole density is as low as 2 x 10(exp 13) dipoles/sq cm, which is quite feasible experimentally,

Yamada, Toshishige↗
NASA NTRS1990

Equivalent circuit models for ac impedance data analysis

A least-squares fitting routine has been developed for the analysis of ac impedance data. It has been determined that the checking of the derived equations for a particular circuit with a commercially available electronics circuit program is essential. As a result of the investigation described, three equivalent circuit models were selected for use in the analysis of ac impedance data.

Danford, M. D.↗
NASA NTRS2008

SiC JFET Transistor Circuit Model for Extreme Temperature Range

A technique for simulating extreme-temperature operation of integrated circuits that incorporate silicon carbide (SiC) junction field-effect transistors (JFETs) has been developed. The technique involves modification of NGSPICE, which is an open-source version of the popular Simulation Program with Integrated Circuit Emphasis (SPICE) general-purpose analog-integrated-circuit-simulating software. NGSPICE in its unmodified form is used for simulating and designing circuits made from silicon-based transistors that operate at or near room temperature. Two rapid modifications of NGSPICE source code enable SiC JFETs to be simulated to 500 C using the well-known Level 1 model for silicon metal oxide semiconductor field-effect transistors (MOSFETs). First, the default value of the MOSFET surface potential must be changed. In the unmodified source code, this parameter has a value of 0.6, which corresponds to slightly more than half the bandgap of silicon. In NGSPICE modified to simulate SiC JFETs, this parameter is changed to a value of 1.6, corresponding to slightly more than half the bandgap of SiC. The second modification consists of changing the temperature dependence of MOSFET transconductance and saturation parameters. The unmodified NGSPICE source code implements a T(sup -1.5) temperature dependence for these parameters. In order to mimic the temperature behavior of experimental SiC JFETs, a T(sup -1.3) temperature dependence must be implemented in the NGSPICE source code. Following these two simple modifications, the Level 1 MOSFET model of the NGSPICE circuit simulation program reasonably approximates the measured high-temperature behavior of experimental SiC JFETs properly operated with zero or reverse bias applied to the gate terminal. Modification of additional silicon parameters in the NGSPICE source code was not necessary to model experimental SiC JFET current-voltage performance across the entire temperature range from 25 to 500 C.

Neudeck, Philip G.↗
NASA NTRS1973

Use of Lorente de No's neuron circuit model for describing acceleratory nystagmus

Results of a previous metric analysis and an electronic simulation of acceleratory nystagmus are given. On this basis, a tentative mathematical model for describing acceleratory nystagmus is reported. The essential content of the model is Lorente de No's neuron circuit, to which the two-factor theory of excitation has been applied.

Valentinuzzi, M.↗
NASA NTRS1991

Equivalent circuit model of traveling-wave maser slow-wave structures

An approach is presented for deriving transmission line equivalent circuits that can approximately model the S-parameter response of traveling wave maser slow wave structures. The technique is illustrated by computing the S-parameter responses of an X-band and S-band maser slow wave structure and comparing these with experimental measurements.

Shell, J.↗
NASA NTRS2003

An Integrated Magnetic Circuit Model and Finite Element Model Approach to Magnetic Bearing Design

A code for designing magnetic bearings is described. The code generates curves from magnetic circuit equations relating important bearing performance parameters. Bearing parameters selected from the curves by a designer to meet the requirements of a particular application are input directly by the code into a three-dimensional finite element analysis preprocessor. This means that a three-dimensional computer model of the bearing being developed is immediately available for viewing. The finite element model solution can be used to show areas of magnetic saturation and make more accurate predictions of the bearing load capacity, current stiffness, position stiffness, and inductance than the magnetic circuit equations did at the start of the design process. In summary, the code combines one-dimensional and three-dimensional modeling methods for designing magnetic bearings.

Provenza, Andrew J.↗
NASA NTRS1981

A three-ring circuit model of the magnetosphere

The magnetosphere is modeled by superimposing a dipole field, a uniform field and a perturbation field due to a simple current system. This current system comprises a ring current in the neutral line of the dipole plus uniform fields, together with vertical currents representing field-aligned currents to the neutral line. The current circuit is closed through two additional ring currents above and below the equatorial plane representing distributed adiabatic perpendicular currents. This system produces many magnetospheric features, among them a magnetopause, bending of magnetic field lines in the anti-solar direction, a magnetotail, and cusps in the day-side of the earth. The objective is to demonstrate that it is not necessary to think of the magnetic field topology as being caused by the flowing plasma carrying field lines. The primary physical problem is to derive the current system from the self-consistent interaction of the solar-wind and magnetospheric plasmas and fields.

Whipple, E. C., Jr.↗
NASA NTRS1980

Comparison of NASCAP modelling results with lumped circuit analysis

Engineering design tools that can be used to predict the development of absolute and differential potentials by realistic spacecraft under geomagnetic substorm conditions are described. Two types of analyses are in use: (1) the NASCAP code, which computes quasistatic charging of geometrically complex objects with multiple surface materials in three dimensions; (2) lumped element equivalent circuit models that are used for analyses of particular spacecraft. The equivalent circuit models require very little computation time, however, they cannot account for effects, such as the formation of potential barriers, that are inherently multidimensional. Steady state potentials of structure and insulation are compared with those resulting from the equivalent circuit model.

Stang, D. B.↗
NASA NTRS1966

Applications of models to circuits

Active device models for linear circuit application and their application to design of operational amplifier and emitter-peaked voltage amplifier stage

SOLID STATE DEVICE↗