SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Hollow-tube drawing or tube sinking theory is based on the concept of continuous distribution of dislocations. Material composition, parameter influence, and die-angle are determining factors in derivation of the theoretical model.
Elastic-plastic shear cracks propagation in two phase composite materials using dislocation model, determining critical fracture strength
Superlattices of GaAs(1-x)p(x) are being incorporated into cascade solar cell structures in order to reduce the dislocation density in the top cells and thus reduce recombination loss and increase output voltage. For a superlattice to effectively block the propagation of dislocations its average composition must be equal to that of the layer beneath it (from efficiency considerations for a cascade cell, the average composition should be about GaAs(.7)P(.3). When superlattices of this approximate composition were grown on GaAs by MOCVD, severe distortion of the crystal layers was observed. The essential features of this distortion are nonplanar morphology and accelerated etching in regions containing excess phosphorus and clusters of dislocations. Similar observations have been made with superlattices grown with two other MOCVD systems, indicating that the problem is of fundamental technological significance, not just an artifact of one particular growth system. The nature of the distortion effect is described, and several strategies for preventing its occurrence are presented.
Hg(1-x)Zn(x)Se alloys have been studied as an alternative to Hg(1-x)Cd(x)Te for the detection of electromagnetic radiation, because the shorter ZnSe and HgSe bonds have been predicted to improve lattice stability. Several ingots with x = 0.1 were directionally solidified using a modified Bridgman-Stockbarger method; one was grown in an applied magnetic field, which greatly reduced radial compositional variations. A method was developed to reduce wetting. This, combined with the convex liquid-solid interface shape, produced boules that were single crystalline after growing about 3.5 cm. Observed surface features indicated ampoule wetting was eliminated using a graphite getter. Microstructural characteristics were greatly improved over HgCdTe alloys. In six boules, a total of only one twin was observed. A method for polishing and producing dislocation etch pits was developed for these alloys, revealing dislocation etch pit densities one to two orders of magnitude less than HgTe-based alloys. A kink in the thermal profile during processing of one boule generated more dislocations than did lattice mismatch due to compositional variations. This alloy has improved microstructural properties and resistance to dislocation formation compared with similar II-VI alloys.
A directionally solidified beta + gamma + gamma-prime Ni-Fe-Al in situ composite alloy of composition Ni50Fe30Al20 has been used to investigate the effect of a plastically soft second phase on the mechanical behavior of a B2 ordered intermetallic alloy. This material exhibits extensive plasticity during compressive deformation at room temperature and fails in shear with extensive gamma + gamma-prime lamellar or rod pullout. The material also exhibits about 10 percent tensile elongation to fracture at room temperature, with final fracture that includes substantial necking of the gamma + gamma-prime lamellae or rods. Observation of slip lines and dislocation substructures discloses that the normally brittle beta matrix undergoes extensive plasticity in order to deform compatibly with the more ductile gamma phase. The plasticity of the beta matrix is accomplished by the generation of glissile dislocations into the beta matrix from the beta/gamma interface region and is enhanced because of a favorable beta-gamma orientation relationship for slip transfer. Ductility enhancement from interface-generated mobile dislocations generated from beta-gamma interfaces is compared to that observed in film-coated beta-NiAl single crystals and FeAl polycrystals.
Electron bombardment induced conductivity and scanning transmission electron microscopy observations on unprocessed and processed edge-defined film-fed growth ribbon show that the phosphorus diffused junction depth is not uniform, and that a variety of chemical impurities precipitate out during processing. Two kinds of precipitates are found (1) 10 nm or less in size, located at the dislocation nodes in sub-boundary like dislocation arrangements formed during processing and (2) large precipitates, the chemical composition of which has been partially identified. These large precipitates emit dense dislocations tangles into the adjacent crystal volume.
Suitably chosen liquid encapsulant placed around melt zone in float-zone crystal-growth system performs four important functions enhancing purity and reducing strains and dislocations in final crystal. In new technique, grow dislocation-free crystals with precisely controlled composition even from materials not amenable to conventional float-zone crystal-growth method. Support provided by encapsulant make it practical to process materials of low surface tension.
The present volume on intermetallic matrix composites discusses the modeling, processing, microstructure/property relationships, and compatibility of intermetallic matrix composites. Attention is given to models for the strength of ductile matrix composites, innovative processing techniques for intermetallic matrix composites, ductile phase toughening of brittle intermetallics, and reactive synthesis of NbAl3 matrix composites. Topics addressed include solidification processing of NbCr2 alloys, Ta and Nb reinforced MoSi2, the microstructure and mechanical behavior of Ni3Al-matrix composites, and ductile-phase toughening of Cr3Si with chromium. Also discussed are dislocation morphologies in TiB2/NiAl, the development of highly impact resistant NiAl matrix composites, the effect of notches on the fatigue life of the SCS-6Ti3Al composite, and the chemical stability of fiber-metal matrix composites.
Two classes of material processing scenarios will feature prominently in future interplanetary exploration: in situ production using locally available materials in lunar or planetary landings and high performance structural materials which carve out a set of properties for uniquely hostile space environments. To be competitive, high performance materials must typically offer orders of magnitude improvements in thermal conductivity or insulation, deliver high strength-to-weight ratios, or provide superior durability (low corrosion and/or ablative character, e.g., in heat shields). The space-related environmental parameters of high radiation flux, low weight, and superior reliability limits many typical aerospace materials to a short list comprising high performance alloys, nanocomposites and thin-layer metal laminates (Al-Cu, Al-Ag) with typical dimensions less than the Frank-Reed-type dislocation source. Extremely light weight carbon-carbon composites and carbon aerogels will be presented as novel examples which define broadened material parameters, particularly owing to their extreme thermal insulation (R-32-64) and low densities (<0.01 g/cu cm) approaching that of air itself. Even with these low-weight payload additions, rocket thrust limits and transport costs will always place a premium on assembling as much structural and life support resources upon interplanetary, lunar, or asteroid arrival. As an example, for in situ lunar glass manufacture, solar furnaces reaching 1700 C for pure silica glass manufacture in situ are compared with sol-gel technology and acid-leached ultrapure (<0.1% FeO) silica aerogel precursors.
Two classes of material processing scenarios will feature prominently in future interplanetary exploration- in situ production using locally available materials in lunar or planetary landings and high performance structural materials which carve out a set of properties for uniquely hostile space environments. To be competitive, high performance materials must typically offer orders of magnitude improvements in thermal conductivity or insulation, deliver high strength-to-weight ratios, or provide superior durability (low corrosion and/or ablative character, e.g. in heat shields). The space-related environmental parameters of high radiation flux, low weight and superior reliability limits many typical aerospace materials to a short list comprising high performance alloys, nanocomposites and thin-layer metal laminates (Al-Cu, Al-Ag) with typical dimensions less than the Frank-Reed-type dislocation source. Extremely light weight carbon-carbon composites and car on aerogels will be presented as novel examples which define broadened material parameters, particularly owing to their extreme thermal insulation (R-32-64) and low densities (less than 0.01 g/cc) approaching that of air itself. Even with these low weight payload additions, rocket thrust limits and transport costs will always place a premium on assembling as much structural and life support resources upon interplanetary, lunar or asteroid arrival. As an example for in situ lunar glass manufacture, solar furnaces reaching 1700 C for pure silica glass manufacture in situ are compared with sol-gel technology and acid-leached ultrapure (less than 0.1% FeO) silica aerogel precursors.
Hg(1-x)Zn(x)Se alloys have been studied as an alternative to HgCdTe for the detection of electromagnetic radiation, because the shorter ZnSe and HgSe bonds were predicted to improve lattice stability. Previous studies showed that optical properties were stable with time and that the microhardness was higher than for HgTe based alloys. However, for this material to be commercially viable, compositional variations must be reduced, and the distribution of defects induced by the growth process must be understood. The basic structural properties of bulk materials were characterized, and dislocation etch pit densities were measured to determine whether the addition of Zn to the HgSe lattice reduced the potential for dislocation formation. Hg(0.9)Zn(0.1)Se alloys were directionally solidified using a modified Bridgman-Stockbarger method and in an applied magnetic field. Radial compositional variations were greatly reduced when solidification occurred in an applied magnetic field. The combination of a convex liquid-solid interface shape and a method for reduced wetting produced boules that were a single crystal after reaching full diameter. Observed surface features indicated ampoule wetting could be eliminated using a graphite getter. Microstructural characteristics were greatly improved over HgCdTe alloys, In six boules, a total of only one twin was observed, and no inclusions were found. A method for polishing and producing dislocation etch pits was developed for these alloys, revealing dislocation etch pit densities one to two orders of magnitude less than HgTe based alloys. A kink in the thermal profile during processing of one boule generated more dislocations than did lattice mismatch due to compositional variations. The results of this investigation indicate this alloy has improved microstructural properties and resistance to dislocation formation compared with similar II-VI alloys, and should be further investigated for the detection of electromagnetic radiation.
Limited ductility and toughness of NiAl and related aluminides near room temperature pose major problems in their potential application as structural materials. An analysis of these problems is presented as part of a review of the flow and fracture behavior of binary NiAl. Following this discussion is a demonstration that conditions of elastic and plastic constraint associated with phase boundaries afforded by surface films, internal lamellae, or precipitates may introduce sufficient densities of mobile dislocations to enhance the ductility of NiAl-based materials by significant amounts. Examples of this behavior are presented for several model materials, including 001- and 123-oriented single crystals of oxide-coated NiAl, directionally solidified beta-gamma-prime (Ni70Al30) and beta-gamma (Ni50Fe30Al20) in situ composites, and several NiAl/precipitate systems. The nature of the resulting dislocation substructures and the effects of several materials variables are described.
Development of lightweight, high specific stiffness engineered materials has been the long term goal of many investigators. Recently, this quest has focused on discontinuously reinforced aluminum metal matrix composites. This paper reviews the fabrication of powder metallurgy discontinuously reinforced metal matrix composites. Emphasis is given to the differences in heat treatment response reported between unreinforced and reinforced powder metallurgy materials. It is proposed that these observations can be rationalized by considering the effects of pre-existing heterogeneous nucleation sites, i.e., the dislocation substructure developed during rapid cooling of discontinuously reinforced aluminum metal matrix composites, on precipitation in reinforced aluminum alloys.
A niobium alloy with 1 percent zirconium and 0.063 percent carbon by weight was investigated in the as-rolled and annealed conditions, and after high-temperature (1350 and 1400 K) exposure with and without an applied stress. In the as-rolled and annealed conditions, large metastable carbides were observed in addition to a regular distribution of small particles. During the high-temperature exposure, the majority of the large carbides were dissolved and a more stable carbide phase formed. This finely dispersed phase had a composition determined to be approximately 70 percent ZrC and approximately 30 percent NbC and showed some evidence of an orientation relationship with the matrix. The precipitates appeared to coarsen slightly after approximately 5000 hr exposure in the presence of an applied stress resulted in a decrease in the size and in the interparticle spacing of the stable precipitates. However, the composition of the precipitate phase and its ability to pin dislocations were not affected by the temperature or stress conditions.
Alloyed semiconductor crystals, such as germanium-silicon (GeSi) and various II-VI alloyed crystals, are extremely important for optoelectronic devices. Currently, high-quality crystals of GeSi and of II-VI alloys can be grown by epitaxial processes, but the time required to grow a certain amount of single crystal is roughly 1,000 times longer than the time required for Bridgman growth from a melt. Recent rapid advances in optoelectronics have led to a great demand for more and larger crystals with fewer dislocations and other microdefects and with more uniform and controllable compositions. Currently, alloyed crystals grown by bulk methods have unacceptable levels of segregation in the composition of the crystal. Alloyed crystals are being grown by the Bridgman process in space in order to develop successful bulk-growth methods, with the hope that the technology will be equally successful on earth. Unfortunately some crystals grown in space still have unacceptable segregation, for example, due to residual accelerations. The application of a weak magnetic field during crystal growth in space may eliminate the undesirable segregation. Understanding and improving the bulk growth of alloyed semiconductors in microgravity is critically important. The purpose of this grant to to develop models of the unsteady species transport during the bulk growth of alloyed semiconductor crystals in the presence of a magnetic field in microgravity. The research supports experiments being conducted in the High Magnetic Field Solidification Facility at Marshall Space Flight Center (MSFC) and future experiments on the International Space Station.
Postseismic horizontal strain and displacement following the June 28, 1992, Landers, California, earthquake (M(sub W) 7.3) is broad scale and cannot be explained solely by delayed afterslip located at the rupturing fault trace. Both the observed strain at Pifion Flat Observatory (PFO) and observed Global Positioning System receiver velocities evolve rapidly after the Landers-Big Bear earthquake sequence. The observed exponential decay of these motions, with timescales of 4-34 days, may reflect a soft creep rheology in the lower crust and brittle-ductile transition zone or even within the seismogenic crust itself. Here a simple model of a two-dimensional screw dislocation in a layered Maxwell viscoelastic Earth is employed in conjunction with a composite rheology to demonstrate that the short timescale transient response modes (approx. = 4-34 days) are consistent with the behavior of a biviscous lower crust. The lowest viscosity of this system is derivable from laboratory experimental data on the long-term creep of natural quarztites, and the highest viscosity is consistent with isostasy-related lower crustal flow in a continental extensional tectonic environment. The model predicts significant stress relaxation at the base of the seismogenic crust. Near the base of the seismogenic zone, and about 4 km away from the mainshock, the rate of predicted relaxation is of the order of 0.01 MPa/ d during the first 20 days of postseismic flow. Oblate spheroidal inclusions at 5% concentration levels that are both aligned and fairly flat in shape and that have a viscosity of 3-4 x 10(exp 15) Pa s are consistent with both the amplitude and decay time of horizontal crustal strain observed at PFO after the Landers mainshock. It is speculated that the structures exposed in cross sections and in seismic reflection profiles of the lower crust that have mylonitic associations are, in part, the cause of such rapid postseismic evolution in southeastern California. Unmylonitized quartz-rich rock at sufficiently elevated temperatures could also contribute to the rapid decay modes.
The microstructure of metals is key to their mechanical properties. The types, density, composition and morphology of crystal defects all have pronounced impact on the properties. Changes to the microstructure occurring during processing and use can be very striking. The emerging technology additive manufacturing (AM) has the potential to improve performance by allowing optimized designs, but the process and environments can lead to unusual microscale features whose properties must be understood and characterized to enable higher technological readiness levels and application. Experimentally, an extensive evaluation of mechanical properties of 3D printed metals is a challenge, and anomalous effects related to the AM process add complexity. We present a new machine learning (ML) model predicting mechanical response based on dislocation mediated plasticity simulations. A large set of 3D discrete dislocation dynamics simulations with wide ranges of loading conditions is transformed to preprocessed data ready for training with the ML model. The trained model can predict the mechanical response of Mo30W for a given microstructure evolution, providing key information essential for optimization of AM processing.
The microstructure of metals is key to their mechanical properties. The types, density, composition and morphology of crystal defects all have pronounced impact on the properties. Changes to the microstructure occurring during processing and use can be very striking. The emerging technology additive manufacturing (AM) has the potential to improve performance by allowing optimized designs, but the process and environments can lead to unusual microscale features whose properties must be understood and characterized to enable higher technological readiness levels and application. Experimentally, an extensive evaluation of mechanical properties of 3D printed metals is a challenge, and anomalous effects related to the AM process add complexity. We present a new machine learning (ML) model predicting mechanical response based on dislocation mediated plasticity simulations. A large set of 3D discrete dislocation dynamics simulations with wide ranges of loading conditions is transformed to preprocessed data ready for training with the ML model. The trained model can predict the mechanical response of Mo30W for a given microstructure evolution, providing key information essential for optimization of AM processing.