SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Controlled synthesis of Ni 2− x Rh x P nanoparticle catalysts enables an understanding of composition-dependent selectivity for the hydrodeoxygenation reaction of phenolic molecules.
Phase selection in Ti-Zr-Hf-Al high-entropy alloys was investigated by in-situ high-energy x-ray diffraction, single-crystal x-ray diffraction, and KKR-CPA electronic-structure methods that address disorder and vacancies, predicting formation enthalpy and chemical short-range order (SRO). Samples with varying Al content were synthesized, characterized, and computationally assessed to ascertain the composition-dependent phase selection, as increased Al content often acts as a stabilizer of a body-centered-cubic structure. Equiatomic TiZrHfAl was especially interesting due to its observed bcc superstructure – a variant of γ-brass with 4 vacancies per cell (not 2 as in γ-brass). We highlight how vacancy ordering mediates selection of this variant of γ-brass, which is driven by vacancy-atom SRO that dramatically suppress all atomic SRO. As vacancies are inherent in processing refractory systems, we expect that similar discoveries await in other high entropy alloys or in revisiting older experimental data.
Electroreduction of carbon monoxide (CO) possesses great potential for achieving the renewable synthesis of hydrocarbon chemicals from CO 2 . We report here selective reduction of CO to acetate using Cu–Pd bimetallic electrocatalysts. High activity and selectivity are demonstrated for CO-to-acetate conversion with >200 mA/cm 2 in geometric current density and >65% in Faradaic efficiency (FE). An asymmetrical C–C coupling mechanism is proposed to explain the composition-dependent catalytic performance and high selectivity toward acetate. This mechanism is supported by the computationally predicted shift of the *CO adsorption from the top-site configuration on Cu (or Cu-rich) surfaces to the bridge sites of Cu–Pd bimetallic surfaces, which is also associated with the reduction of the CO hydrogenation barrier. Further kinetic analysis of the reaction order with respect to CO and Tafel slope supports a reaction pathway with *CO–*CHO recombination following a CO hydrogenation step, which could account for the electroreduction of CO to acetate on the Cu–Pd bimetallic catalysts. Furthermore, our work highlights how heteroatomic alloy surfaces can be tailored to enable distinct reaction pathways and achieve advanced catalytic performance beyond monometallic catalysts.
Polyhydroxyalkanoates (PHAs) have emerged as a promising class of biosynthesizable, biocompatible, and biodegradable polymers to replace petroleum-based plastics for addressing the global plastic pollution problem. Although PHAs offer a wide range of chemical diversity, the structure–property relationships in this class of polymers remain poorly established. In particular, the available experimental data on the mechanical properties is scarce. In this contribution, we have used molecular dynamics simulations employing a recently developed forcefield to predict chemical trends in mechanical properties of PHAs. Specifically, we make predictions for Young’s modulus, and yield stress for a wide range of PHAs that exhibit varying lengths of backbone and side chains as well as different side chain functional groups. Deformation simulations were performed at six different strain rates and six different temperatures to elucidate their influence on the mechanical properties. Our results indicate that Young’s modulus and yield stress decrease systematically with increase in the number of carbon atoms in the side chain as well as in the polymer backbone. In addition, we find that the mechanical properties were strongly correlated with the chemical nature of the functional group. The functional groups that enhance the interchain interactions lead to an enhancement in both the Young’s modulus and yield stress. Finally, we applied the developed methodology to study composition-dependence of the mechanical properties for a selected set of binary and ternary copolymers. Overall, our work not only provides insights into rational design rules for tailoring mechanical properties in PHAs, but also opens up avenues for future high throughput atomistic simulation studies geared towards identifying functional PHA polymer candidates for targeted applications.
Mass-selected cluster deposition and scanning tunneling microscopy (STM) were used to investigate the surface structure and thermal stability of Ti 3 O y (y = 5, 6) clusters on a Cu(111) surface. STM imaging shows that the substoichiometric Ti 3 O 5 clusters aggregate into large dendritic assemblies at step edges, while the stoichiometric Ti 3 O 6 clusters are highly dispersed as single or small groupings of clusters. Cluster deposition also results in extensive reconstruction of the Cu(111) surface. The Ti 3 O 5 /Cu(111) surface exhibits one Cu-layer deep pits that are ringed by cluster assemblies that nucleate and grow at the perimeter step edges. By comparison, the Ti 3 O 6 /Cu(111) surface consists of irregular step edges and small one Cu-layer islands that are decorated with clusters. The restructuring of the Cu(111) surface is attributed to strong Cu-cluster interactions that release Cu adatoms from the step edges. This mechanism is supported by density functional theory (DFT) calculations, which predict that the Cu adatom attachment to the clusters is energetically favorable. Annealing the surfaces at elevated temperatures (400-700 K) results in higher densities of irregular steps, pits and isolated Cu islands as well as increased cluster aggregation. In conclusion, this work highlights adatom-cluster interactions as another manifestation of strong cluster-support interactions that can significantly alter the nature of the oxide-metal interface.
Al-Ce-based alloys are promising candidates for additive manufacturing (AM) due to their hot-cracking resistance and because they do not require heat treatment to obtain precipitation strengthening. Rapid solidification rates enabled by AM methods can lead to enhanced mechanical properties; however, the strengthening mechanisms over large composition ranges were unclear. Here, combinatorial synthesis by directed-energy deposition (DED) and hardness measurements were used to rapidly map the composition-dependent strength of the ternary Al-Ce-Mg system. Tensile testing and microstructure characterization of selected compositions were performed to elucidate the compositional dependence of the strengthening mechanisms. Al 11 Ce 3 precipitates were present in all cases, and the maximum hardness (1.25 GPa) was measured for the Al-8Ce-10Mg composition. A combination of (i) Hall-Petch strengthening, based on the FCC-matrix-phase cell size; (ii) particle strengthening, based on Al 11 Ce 3 volume fraction and size; and (iii) solid-solution strengthening, based on Mg composition of the matrix phase, were used to account for the measured strengths. Vickers hardness is shown to correlate well with ultimate tensile strength in these alloys, highlighting the value of surface-based techniques for rapid screening.
Single- and few-layered two-dimensional (2D) nanomaterials have attracted intense research interest in the last two decades due to their unique electronic and optoelectronic properties leading to various potential applications. Herein, we report the colloidal synthesis of Bi-based 2D perovskite nanosheets (PEG6-NH 3 +) n Cs 3-n Bi 2 X 9 , where X = CI, Br, and I, through careful design of reaction conditions and selection of poly(ethylene glycol) (PEG6) surface passivating ligands. The 2D nanosheets are similar to 5 nm in thickness with micron-sized lateral dimensions and display composition-dependent band gap and work function modulation. Furthermore, small-angle X-ray scattering analysis substantiates that the individual inorganic crystal layer, Cs 3-n Bi 2 X 9 , is separated by the spacer, PEG6 ligand. Additionally, we determined that PEG6-NH 2 is an essential passivating ligand and spacer for the formation of Bi-based 2D nanosheets. Most importantly, controlled crystallization of the colloidal dispersion of nanosheets results in the formation of superlattice microstructures of the quasi-Ruddlesden-Popper phase. These microstructures can be exfoliated to ultrathin nanosheets by overcoming the van der Waals interaction between the organic passivating layers. The controlled synthesis of lead-free 2D perovskite nanosheets presented here can expand their utility to photocatalytic and optoelectronic applications with reduced toxicity.
The ultra-high-sensitivity aerosol spectrometer (UHSAS) differs from most other optical particle spectrometers by using a high-power infrared (IR) laser to detect small particles and reduce the sizing ambiguity due to the non-monotonicity of scattering with particle size. During the NASA ORACLES project (ObseRvations of Aerosols above CLouds and their intEractionS) over the southeast Atlantic Ocean, the UHSAS clearly undersized particles in the biomass burning plume extending from southern Africa. Since the horizontal and vertical extent of the plume was vast, the NASA P-3B research aircraft often flew through a fairly uniform biomass burning plume for periods exceeding 30 min, sufficient time to explore the details of the UHSAS response by selecting single particle sizes with a differential mobility analyzer (DMA) and passing them to the UHSAS. This was essentially an in-flight calibration of the UHSAS using the particles of interest. Two modes of responses appeared. Most particles were undersized by moderate amounts, ranging from not at all for 70 nm aerosols to 15 % for 280 nm particles. Mie scattering calculations show that composition-dependent refractive index of the particles cannot explain the pattern. Heating of brown carbon or tarballs in the beam causing evaporation and shrinking of the particles is the most plausible explanation, though mis-sizing due to non-sphericity cannot be ruled out. A small fraction (10 %–30 %) of the particles were undersized by 25 % to 35 %. Those were apparently the particles containing refractory black carbon. Laboratory calibrations confirm that black carbon is drastically undersized by the UHSAS, because particles heat to their vaporization point and shrink. A simple empirical correction equation was implemented that dramatically improves agreement with DMA distributions between 100 and 500 nm. It raised the median particle diameter by 18 nm, from 163 to 181 nm, during the August 2017 deployment and by smaller amounts during deployments with less intense pollution. Calculated scattering from UHSAS size distributions increased by about 130 %, dramatically improving agreement with scattering measured by nephelometers. The correction is only valid in polluted instances; clean marine boundary layer and free troposphere aerosols behaved more like the calibration spheres. We were unable to directly test the correction between 500 and 1000 nm, though aerodynamic particle sizer (APS) data appear to show that the correction is poor at the largest diameters, which is no surprise as the composition of those particles is likely to be quite different than that of the accumulation mode. This adds to the evidence that UHSAS data must be treated cautiously whenever the aerosol may absorb infrared light. Similar corrections may be required whenever brown carbon aerosol is present.
Chemical looping air separation (CLAS) is a promising technology to generate oxygen-rich gas streams to enable efficient carbon dioxide capture during fossil fuel combustion or gasification. CLAS relies on the capture and release of oxygen from the atmosphere using the redox properties of an oxygen-selective solid oxide carrier. This study investigates the redox characteristics of Ba 1−x Sr x FeO 3−δ (0.0 ≤ x ≤ 0.417, 0.0 ≤ δ ≤ 0.5) using a combination of density functional theory (DFT) calculations and experimental verification using X-ray diffraction, thermogravimetric analysis, and oxygen-temperature-programmed desorption. The DFT computed energies of the Ba 1−x Sr x FeO 3−δ perovskites reveal a composition-dependent transition from hexagonal to cubic phases as the Sr-concentration or oxygen vacancy concentration increases. Oxygen vacancy formation energies of the cubic perovskites are found to be lower than those of their hexagonal counterparts. A low oxygen diffusion barrier of ∼1 eV combined with the thermodynamic preference of Ba 1−x Sr x FeO 3−δ compositions that form in a cubic phase suggests them as promising candidates for oxygen storage applications. The experimental results corroborate this finding by identifying Ba 0.75 Sr 0.25 FeO 3−δ in the cubic phase as an optimal composition offering low-temperature oxygen storage capacities comparable to that of the state-of-the-art Sr 0.75 Ca 0.25 FeO 3−δ perovskite oxygen storage material at 325 °C and 350 °C.
Since the discovery of the Frank–Kasper (FK) phase a decade ago, single-component block copolymer systems have offered unique opportunities to explore the structural and phase-transition properties of topologically close-packed FK phases composed of point-particle motifs. Here, we present the formation of complex low-symmetry phases and their thermodynamic stability using high-χ and high-ε linear diblock copolymers, where χ and ε are the Flory–Huggins interaction parameter and conformational asymmetry between the two blocks, respectively. In this work, a series of polydimethylsiloxane-b-poly(2,2,2-trifluoroethyl acrylate) (PDMS-b-PTFEA) copolymers are prepared by tuning the volume fraction ($f_{\text{PTFEA}}$) of a minor PTFEA block. The packing structures of PDMS-b-PTFEAs are mapped in the space of temperature versus $f_{\text{PTFEA}}$ using X-ray scattering measurements. In addition to the packing structures reported earlier, we identify another A15 phase at higher $f_{\text{PTFEA}}$ close to a hexagonally packed cylinder (HEX) phase and establish the phase sequence of HEX–A15–σ–C14–BCC with decreasing $f_{\text{PTFEA}}$. Theoretical calculation of relative free-energy densities confirms the experimental phase sequence of the composition-dependent sphere-packing structures. Interestingly, the domain sizes of three-dimensional (3D) sphere-packing structures are nearly temperature-invariant compared to that of a two-dimensional HEX structure, and we attribute this dimensional stability to the strong enthalpic effects in the formation of 3D packing structures and the geometrical characteristics of spherical domains. Our results demonstrate that the interaction parameter χ, together with the known role of conformational asymmetry ε, serves as the primary thermodynamic parameter for selecting and stabilizing various low-symmetry packing structures in sphere-forming linear diblock copolymer systems.
Large-batch numerical, CALculation of PHAse Diagrams (CALPHAD)-based solidification cracking calculations are performed and then analyzed with machine learning methods to generate models that relate chemistry of refractory alloys to cracking susceptibility. Kou’s solidification cracking index is used to study the refractory alloys including O, N, C binary mixtures with Mo, Ta, Nb, and W, the molybdenum-based TZM, Niobium-based C103, and Tantalum-based T111 and Ta-10 W, as well as hypothetical refractory ternary alloys. Findings strongly validate Kou’s Crack Susceptibility Index (CSI) against Varestraint test data for Nb- and Ta-based alloys, establishing CSI thresholds where refractory alloys with CSI < 15,000 K are likely weldable, CSI > 15,000 K are prone to cracking, and CSI > 25,000 K are likely unweldable (or unprintable). Furthermore, interstitial elements C, N, and O significantly increase crack susceptibility, with some existing material specifications coinciding with peak cracking susceptibility concentrations. Finally, machine learning-derived elemental potency factors enable rapid prediction of CSI from alloy chemistry for C103, TZM, Ta-10 W, and T-111 alloys. These results provide practical guidance for feedstock selection, powder reuse limits, and alloy specification amendments for welding and additive manufacturing applications.
High-entropy alloys (HEAs) represent a promising class of materials with exceptional structural and functional properties. However, their design and optimization pose challenges due to the large composition-phase space coupled with the complex and diverse nature of the phase formation dynamics. In this study, a data-driven approach that utilizes machine learning (ML) techniques to predict HEA phases and their composition-dependent phases is proposed. By employing a comprehensive dataset comprising 5692 experimental records encompassing 50 elements and 11 phase categories, we compare the performance of various ML models. Our analysis identifies the most influential features for accurate phase prediction. Furthermore, the class imbalance is addressed by employing data augmentation methods, raising the number of records to 1500 in each category, and ensuring a balanced representation of phase categories. The results show that XGBoost and Random Forest consistently outperform the other models, achieving 86% accuracy in predicting all phases. Additionally, this work provides an extensive analysis of HEA phase formers, showing the contributions of elements and features to the presence of specific phases. We also examine the impact of including different phases on ML model accuracy and feature significance. Notably, the findings underscore the need for ML model selection based on specific applications and desired predictions, as feature importance varies across models and phases. This study significantly advances the understanding of HEA phase formation, enabling targeted alloy design and fostering progress in the field of materials science.
The field of cluster science is drawing increasing attention due to the strong size and composition-dependent properties of clusters and the exciting prospect of clusters serving as the building blocks for materials with tailored properties. However, identifying a unifying central paradigm that provides a framework for classifying and understanding the diverse behaviors is an outstanding challenge. One such central paradigm is the superatom concept that was developed for metallic and ligand-protected metallic clusters. The periodic electronic and geometric closed shells in clusters result in their properties being based on the stability they gain when they achieve closed shells. This stabilization results in the clusters having a well-defined valence allowing them to be classified as superatoms – thus, extending the periodic table to a third dimension. This perspective focuses on extending the superatomic concept to ligated metal-chalcogen clusters that have recently been synthesized in solutions and form assemblies with counterions that have wide-ranging applications. Here we illustrate that the periodic patterns emerge in the electronic structure of ligated metal-chalcogenide clusters. The stabilization gained by the closing of their electronic shells allows for the prediction of their redox properties. Further investigations reveal how the selection of ligands may control the redox properties of the superatoms. These ligated clusters may serve as chemical dopants for two-dimensional semiconductors to control their transport characteristics. Superatomic molecules of multiple metal-chalcogen superatoms allow for the formation of nano pn junctions ideal for directed transport and photon harvesting. As a result, the perspective outlines future developments, including the synthesis of magnetic superatoms.
Density-functional theory (DFT) is used to identify phase-equilibria in multi-principal-element and high-entropy alloys (MPEAs/HEAs), including duplex-phase and eutectic microstructures. Here, a combination of composition-dependent formation energy and electronic-structure-based ordering parameters were used to identify a transition from FCC to BCC favoring mixtures, and these predictions experimentally validated in the Al-Co-Cr-Cu-Fe-Ni system. A sharp crossover in lattice structure and dual-phase stability as a function of composition were predicted via DFT and validated experimentally. The impact of solidification kinetics and thermodynamic stability was explored experimentally using a range of techniques, from slow (castings) to rapid (laser remelting), which showed a decoupling of phase fraction from thermal history, i.e., phase fraction was found to be solidification rate-independent, enabling tuning of a multi-modal cell and grain size ranging from nanoscale through macroscale. Strength and ductility tradeoffs for select processing parameters were investigated via uniaxial tension and small-punch testing on specimens manufactured via powder-based additive manufacturing (directed-energy deposition). This work establishes a pathway for design and optimization of next-generation multiphase superalloys via tailoring of structural and chemical ordering in concentrated solid solutions.