Search NASA⌕ Search

SEARCH · Search NASA

Results for “conductive films”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Real-Time Deposition Monitor for Ultrathin Conductive Films

A device has been developed that can be used for the real-time monitoring of ultrathin (2 or more) conductive films. The device responds in less than two microseconds, and can be used to monitor film depositions up to about 60 thick. Actual thickness monitoring capability will vary based on properties of the film being deposited. This is a single-use device, which, due to the very low device cost, can be disposable. Conventional quartz/crystal microbalance devices have proven inadequate to monitor the thickness of Pd films during deposition of ultrathin films for hydrogen sensor devices. When the deposited film is less than 100 , the QCM measurements are inadequate to allow monitoring of the ultrathin films being developed. Thus, an improved, high-sensitivity, real-time deposition monitor was needed to continue Pd film deposition development. The new deposition monitor utilizes a surface acoustic wave (SAW) device in a differential delay-line configuration to produce both a reference response and a response for the portion of the device on which the film is being deposited. Both responses are monitored simultaneously during deposition. The reference response remains unchanged, while the attenuation of the sensing path (where the film is being deposited) varies as the film thickness increases. This device utilizes the fact that on high-coupling piezoelectric substrates, the attenuation of an SAW undergoes a transition from low to very high, and back to low as the conductivity of a film on the device surface goes from nonconductive to highly conductive. Thus, the sensing path response starts with a low insertion loss, and as a conductive film is deposited, the film conductivity increases, causing the device insertion loss to increase dramatically (by up to 80 dB or more), and then with continued film thickness increases (and the corresponding conductivity increases), the device insertion loss goes back down to the low level at which it started. This provides a continuous, real-time monitoring of film deposition. For use with different films, the device would need to be calibrated to provide an understanding of how film thickness is related to film conductivity, as the device is responding primarily to conductivity effects (and not to mass loading effects) in this ultrathin film regime.

Hines, Jacqueline↗
NASA NTRS1991

Testing Conductive Films For Continuity

Apparatus tests thin conductive films for continuity without touching them. Specimen irradiated with 10-keV electrons; then noncontacting electrostatic probe scans specimen and measures charge on spot directly under it. Avoids damage to film and error from contact resistance resulting from touching film with conventional probe. Developed to determine integrity of conductive coats applied to surfaces of dielectric materials to inhibit accumulation of electrostatic charges.

Leung, Philip L.↗
DOE OSTI2021

ANOMALOUS SKIN EFFECT STUDY OF NORMAL CONDUCTING FILM

For the radiofrequency (RF) applications of normal conducting film with large mean free path at high frequency and low temperature, the anomalous skin effect differs considerably from the normal skin effect with field decaying exponentially in the film. Starting from the relationship be-tween the current and the electric field (E field) in the film, the amplitude of E field along the film depth is calculated and is found to be non-monotonic. The surface impedance is found to have a minimum value at certain film thickness.

43 PARTICLE ACCELERATORS↗
NASA NTRS1995

Experiments On Transparent Conductive Films For Spacecraft

Report describes experiments on thin, transparent, electrically conductive films made, variously, of indium tin oxide covered by magnesium fluoride (ITO/MgF2), aluminum-doped zinc oxide (AZO), or pure zinc oxide (ZnO). Films are candidates for application to such spacecraft components, including various optoelectronic devices and window surfaces that must be protected against buildup of static electric charge. On Earth, such films useful on heat mirrors, optoelectronic devices, gas sensors, and automotive and aircraft windows.

Perez-Davis, Marla E.↗
NASA NTRS2004

Transparent, Weakly Conductive Films for Space Applications

Electrically insulating spacecraft surfaces are vulnerable to nonuniform charge buildup due to particles emitted by the sun. On Mars, insulating surfaces of exploration vehicles and structures will be affected by dust coatings possibly held in place by triboelectric surface charge. Application of a conductive film may be a solution to the charging problem, but the coating must be highly transparent if used on solar panels, lenses, etc. Sheet resistivity requirements depend on the application and are in the range 10(exp 2) - 10(exp 8) ohms/square. Co-deposited indium tin oxide (ITO) and MgF2 is promising, with high transparency, tailorable electrical properties, and durability to atomic oxygen. Due to ITO's relatively narrow bandgap (approximately 3.5 eV), the film might absorb enough ultraviolet to protect polymeric substrates. Recent work on dual-magnetron-sputtered ITO-MgF2 showed that a variety of polymeric substrates can be coated at room temperature. However, the sheet resistivity is very sensitive to composition, suggestive of a percolation transition. This could be a serious problem for large-scale coating production. We will report on attempts to control film composition by plasma emission monitoring of the ITO and MgF2 guns.

Griffin, John↗
NASA NTRS2005

Protection of 2-(3-Thienyl)ethanol with 3-Thienylacetic Acid and Hard Cross- Linked Conducting Films by Electropolymerization of the Ester

The ester (compound 1) of 2-(3-thienyl)ethanol (T-etOH) with 3-thienylacetic acid was synthesized as a monomer whose two thiophene groups could be electropolymerized independently, becoming members of different polymer chains in a highly-crosslinked highly-insoluble polymer. Indeed, 1 was electropolymerized successfully alone and together with 3-methylthiophene (3MeT). Films of poly(1) are hard (3H, as opposed to less than 6B for poly(3MeT)), and the close proximity of the polymeric strands creates pi-stacking interactions. The behavior of 1 suggests that by: (a) limiting the potential used for the oxidation of monomeric esters of T-etOH at the foot of their oxidation waves (less than 1.8 V vs. Ag/AgCl); and, (b) compensating for the decrease in the electrogenerated radical concentration by increasing the monomer concentration, practically all esters of T-etOH should be electropolymerizable. This was confirmed by durable film formation from the archetypical ester of T-etOH, the 2-(3-thienyl)ethyl acetate (T-etOAc), whose homo-electropolymerization is reported for the first time.

Leventis, Nicholas↗
NASA NTRS1993

Synthesis of novel electrically conducting polymers: Potential conducting Langmuir-Blodgett films and conducting polymers on defined surfaces

Based on previous results involving thiophene derived electrically conducting polymers in which it was shown that thiophene, 3-substituted thiophenes, furans, and certain oligomers of these compounds showed electrical conductivity after polymerization. The conductivity was in the order of up to 500 S/cm. In addition, these polymers showed conductivity without being doped and most of all they were practically inert toward ambient conditions. They even could be used in aqueous media. With these findings as a guide, a number of 3-long-chain-substituted thiophenes and 1-substituted-3-long-chain substituted pyrrols were synthesized as monomers for potential polymeric electrically conducting Langmuir-Blodgett films.

Zimmer, Hans↗
DOE OSTI2021

High stability of flexible perovskite transparent conductive oxide film via van der Waals heteroepitaxy

Transparent conducting oxides (TCOs), such as indium-tin oxide (ITO) and indium gallium zinc oxide (IGZO), are essential components in the design of flexible optoelectronic devices. However, it is still a challenge to prepare low-cost flexible transparent conductive film for achieving the flexible functionality together with high optical transparency and electrical conductivity. Herein, fluorphlogopite (mica) is selected as the bendable and transparent substrate for the fabrication of low-cost perovskite CaVO 3 TCO epitaxial film. Benefitting from thin mica substrate with high Young’s modulus of 200 GPa, flexible CaVO 3 TCO epitaxial film exhibits high mechanical stability in terms of electrical conductivity and optical transparency after bending up to 10 5 cycles. The change of resistance can reflect the bending curvature and strain state. Finally, our results provide a new pathway to design superior mechanical flexibility and stability CaVO 3 TCO films for application in flexible, light-weight, and portable smart optoelectronic devices.

36 MATERIALS SCIENCE↗
NASA NTRS1994

Pressure sensor using liquid crystals

A pressure sensor includes a liquid crystal positioned between transparent, electrically conductive films (18 and 20), that are biased by a voltage (V) which induces an electric field (E) that causes the liquid crystal to assume a first state of orientation. Application of pressure (P) to a flexible, transparent film (24) causes the conductive film (20) to move closer to or farther from the conductive film (18), thereby causing a change in the electric field (E'(P)) which causes the liquid crystal to assume a second state of orientation. Polarized light (P.sub.1) is directed into the liquid crystal and transmitted or reflected to an analyzer (A or 30). Changes in the state of orientation of the liquid crystal induced by applied pressure (P) result in a different light intensity being detected at the analyzer (A or 30) as a function of the applied pressure (P). In particular embodiments, the liquid crystal is present as droplets (10) in a polymer matrix (12) or in cells (14) in a polymeric or dielectric grid (16) material in the form of a layer (13) between the electrically conductive films (18 and 20). The liquid crystal fills the open wells in the polymer matrix (12) or grid (16) only partially.

Parmar, Devendra S.↗
NASA NTRS2004

Comparison of Classical and Charge Storage Methods for Determining Conductivity of Thin Film Insulators

Conductivity of insulating materials is a key parameter to determine how accumulated charge will distribute across the spacecraft and how rapidly charge imbalance will dissipate. Classical ASTM and IEC methods to measure thin film insulator conductivity apply a constant voltage to two electrodes around the sample and measure the resulting current for tens of minutes. However, conductivity is more appropriately measured for spacecraft charging applications as the "decay" of charge deposited on the surface of an insulator. Charge decay methods expose one side of the insulator in vacuum to sequences of charged particles, light, and plasma, with a metal electrode attached to the other side of the insulator. Data are obtained by capacitive coupling to measure both the resulting voltage on the open surface and emission of electrons from the exposed surface, as well monitoring currents to the electrode. Instrumentation for both classical and charge storage decay methods has been developed and tested at Jet Propulsion Laboratory (JPL) and at Utah State University (USU). Details of the apparatus, test methods and data analysis are given here. The JPL charge storage decay chamber is a first-generation instrument, designed to make detailed measurements on only three to five samples at a time. Because samples must typically be tested for over a month, a second-generation high sample throughput charge storage decay chamber was developed at USU with the capability of testing up to 32 samples simultaneously. Details are provided about the instrumentation to measure surface charge and current; for charge deposition apparatus and control; the sample holders to properly isolate the mounted samples; the sample carousel to rotate samples into place; the control of the sample environment including sample vacuum, ambient gas, and sample temperature; and the computer control and data acquisition systems. Measurements are compared here for a number of thin film insulators using both methods at both facilities. We have found that conductivity determined from charge storage decay methods is 102 to 104 larger than values obtained from classical methods. Another Spacecraft Charging Conference presentation describes more extensive measurements made with these apparatus. This work is supported through funding from the NASA Space Environments and Effects Program and the USU Space Dynamics Laboratory Enabling Technologies Program.

Swaminathan, Prasanna↗
NASA NTRS1994

Transparent conducting thin films for spacecraft applications

Transparent conductive thin films are required for a variety of optoelectronic applications: automotive and aircraft windows, and solar cells for space applications. Transparent conductive coatings of indium-tin-oxide (ITO)-magnesium fluoride (MgF2) and aluminum doped zinc oxide (AZO) at several dopant levels are investigated for electrical resistivity (sheet resistance), carrier concentration, optical properties, and atomic oxygen durability. The sheet resistance values of ITO-MgF2 range from 10(exp 2) to 10(exp 11) ohms/square, with transmittance of 75 to 86 percent. The AZO films sheet resistances range from 10(exp 7) to 10(exp 11) ohms/square with transmittances from 84 to 91 percent. It was found that in general, with respect to the optical properties, the zinc oxide (ZnO), AZO, and the high MgF2 content ITO-MgF2 samples, were all durable to atomic oxygen plasma, while the low MgF2 content of ITO-MgF2 samples were not durable to atomic oxygen plasma exposure.

Perez-Davis, Marla E.↗
NASA NTRS1994

Electrically Conductive Polyimide Films Containing Gold Surface

Polyimide films exhibiting high thermo-oxidative stability and including electrically conductive surface layers containing gold made by casting process. Many variations of basic process conditions, ingredients, and sequence of operations possible, and not all resulting versions of process yield electrically conductive films. Gold-containing layer formed on film surface during cure. These metallic gold-containing polyimides used in film and coating applications requiring electrical conductivity, high reflectivity, exceptional thermal stability, and/or mechanical integrity. They also find commercial potential in areas ranging from thin films for satellite antennas to decorative coatings and packaging.

Caplan, Maggie L.↗