Search NASA⌕ Search

SEARCH · Search NASA

Results for “crosslinked electrolyte”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

In-situ polymerized and crosslinked electrolytes with interchangeable Li/Na transport for battery applications

The next generation of batteries requires electrolytes with high conductivity, mechanical stability, good adhesion with electrodes, wide electrochemical windows, and scalability. The present study introduces a concept of doped quasi single-ion conducting copolymers based on methacrylate-(trifluoromethanesulfonyl)imide (TFSI) and vinyl ethylene carbonate which at room temperature are mechanically robust and display ionic conductivities of ~0.1 mS/cm. These electrolytes can be polymerized/crosslinked in-situ, making them easily implementable in current battery manufacturing technologies. They also allow for switching between Li + and Na + transport using simple chemistry procedures. To demonstrate their potential for battery applications, the newly developed Li conductors have been tested in symmetric cells, exhibiting overall impedance below 350 Ohm and plating/stripping stability up to 1 mA/cm 2 . Moreover, lithium metal batteries incorporating this electrolyte and high-voltage Lithium Nickel Manganese Cobalt Oxide (NMC) cathodes show good capacity retention (~79%) during charging and discharging for 80 cycles at C/10 rate and a Coulombic efficiency close to 100% in the entire measurement range. The compositional, mechanical and electrochemical versatility of these electrolytes opens new venues for the design of polymer-based batteries capable of fast charging and extended cycle life, aligning with the current global green energy storage strategies.

Polymer electrolytes↗
DOE OSTI2025

Ion Transport in Concentrated Crosslinked Solid Polymer Electrolytes

Crosslinking polymers is a common approach to create mechanically stable solid materials such as polymer electrolytes for lithium batteries. In conventional liquid electrolytes, the solvent molecules move freely to accommodate the field-induced motion of ions. However, in crosslinked polymer electrolytes, the rearrangement of polymer segments is constrained by the deformation limits of the network. Herein, we develop a new transport model that accounts for both the formation of concentration gradients and the elasticity of the electrolyte. The elasticity is incorporated by adding an additional term related to the entropy of crosslinked strands to the electrochemical potential of the salt. The resulting Crosslink Model contains two adjustable parameters: $\mathcal{N}$, the average number of monomers in a strand, and λ crit , the maximum strain the network can sustain. These solid-like constraints produce singularities in the governing transport equations, fundamentally altering the concentration profiles. Plateaus in salt concentrations emerge near the electrodes, and network elasticity introduces a strain overpotential. When compared to a Baseline Model ($\mathcal{N}$ → ∞, equivalent to concentrated solution theory), which predicts steepest gradients near the electrodes, both models yield similar current–voltage relationships. Model predictions are compared to electrochemical data for a poly(ethylene oxide)-based crosslinked polymer electrolyte.

Patel, Vivaan [University of California, Berkeley,↗
DOE OSTI2020

Well-designed Crosslinked Polymer Electrolyte Enables High Ionic Conductivity and Enhanced Salt Solvation

A new facile single-step method to fabricate crosslinked polymer electrolyte membranes consisting of branched poly(ethyleneimine), (PEI) and poly(ethylene oxide), (PEO) is demonstrated. The membranes exhibit excellent ionic conductivity (1.2 × 10 –3 S cm –1 at 80 °C) with minimal addition of plasticizer (20 wt%). The amine functional group in the PEI-PEO crosslinked matrix provides Lewis basic and hydrogen bonding characteristics that facilitate the dissolution of lithium salt and enables a higher cation transport number than a PEO crosslinked matrix. The glass transition temperature, degree of crystallinity, and room temperature storage modulus increases with decreasing crosslink density and increasing ratio of free amines. The resultant ionic conductivity and mechanical strength can be flexibly tailored by varying the molar ratio of free amine moieties in the crosslinked PEI-PEO matrix. This study provides an improved synthesis method, in-depth characterization, and fundamental insights on the effect of free amine moieties on the transport properties of a highly conductive gel polymer electrolyte.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Plasticizer-Free Gradient-Crosslinked Polyurethane Electrolyte for Room-Temperature Solid-State Lithium Batteries

Polymer-based solid-state electrolytes are promising for next-generation lithium metal batteries, yet their limited ionic conductivity and mechanical stability at ambient conditions remain key challenges. Herein, we report a novel gradient crosslinked polymer electrolyte (PU/PUA/PU) synthesized via a sequential in situ UV-curing process that integrates a mechanically robust polyurethane acrylate (PUA) core with soft linear polyurethane (PU) interfaces. This all-solid membrane operates without any liquid plasticizer and the interfacial PU layers ensure low interfacial resistance and intimate electrode contact, while the PUA core provides enhanced dimensional stability and dendrite suppression. As a result, the gradient electrolyte delivers an impressive ∼2.6 × 10 −4 S cm −1 ionic conductivity at 25 °C (two orders of magnitude higher than conventional PEO) and remains electrochemically stable >5 V (vs Li + /Li). Structural analysis confirms the formation of a well-defined crosslinked network with suppressed crystallinity and expanded interchain spacing. Electrochemical impedance spectroscopy (EIS) and linear sweep voltammetry (LSV) further validate these properties. When applied in a Li||NMC811 cell, the PU/PUA/PU electrolyte delivers stable cycling with high capacity at both 60 °C and 25 °C, demonstrating its potential for room-temperature solid-state battery applications without reliance on plasticizers or heating. In conclusion, this gradient design offers a practical path toward ambient-condition operation of solid-state lithium batteries, providing a paradigm for overcoming the traditional trade-off between ionic conductivity and mechanical robustness.

25 ENERGY STORAGE↗
DOE OSTI2017

Crosslinked perfluoropolyether solid electrolytes for lithium ion transport

Perfluoropolyethers (PFPE) are commercially available non-flammable short chain polymeric liquids. End-functionalized PFPE chains solvate lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt and these mixtures can be used as electrolytes for lithium (Li) batteries. Here we synthesize and characterize a new class of solid PFPE electrolytes. The electrolytes are made by either thermal or UV crosslinking PFPE chains with urethane methacrylate end-groups. For the synthesis of thermally crosslinked electrolytes, polyhedral oligomeric silsesquioxane (POSS) with organic acrylopropyl groups was used as crosslinker agent, while for UV cured electrolytes a photoinitiatior was used. We present thermal, morphological, and electrical data of the solid electrolytes. We compare these properties with those of the two parent liquids (PFPE with urethane methacrylate end-groups and POSS with acrylopropyl groups) mixed with LiTFSI. The solubility limit of LiTFSI in the PFPE-based solids is higher than that in the liquids. The conductivity data are analyzed using the Vogel–Tamman–Fulcher equation. In conclusion, the concentration of effective charge carriers is a strong function of the nature of the solvent (solid versus liquid) whereas the activation energy is neither a strong function of the nature of the solvent nor salt concentration.

25 ENERGY STORAGE↗
NASA NTRS2014

Branched Rod-Coil Polyimide-Poly(Alkylene Oxide) Copolymers and Electrolyte Compositions

Crosslinked polyimide-poly(alkylene oxide) copolymers capable of holding large volumes of liquid while maintaining good dimensional stability. Copolymers are derived at ambient temperatures from amine endcapped amic-acid oligomers subsequently imidized in solution at increased temperatures, followed by reaction with trifunctional compounds in the presence of various additives. Films of these copolymers hold over four times their weight at room temperature of liquids such as ionic liquids (RTIL) and/or carbonate solvents. These rod-coil polyimide copolymers are used to prepare polymeric electrolytes by adding to the copolymers various amounts of compounds such as ionic liquids (RTIL), lithium trifluoromethane-sulfonimide (LiTFSi) or other lithium salts, and alumina.

Meador, Maryann B.↗
DOE OSTI2025

Tunable Crosslinked Ether Polymer Network Electrolytes for High‐Performance All‐Solid‐State Sodium Batteries

All-solid-state batteries (ASSBs) are critical for achieving high energy density and enhanced safety. Solid polymer electrolytes (SPEs) offer key advantages over other electrolytes, including improved safety, flexibility, and interfacial contact. Among the SPEs, ether-based polymers are widely studied due to their ease of processing and high ionic conductivity (σi) in the amorphous state. In this work, the introduction of poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) into an SPE matrix composed of poly(ethylene glycol) diacrylate (PEGDA), poly(ethylene glycol) (PEG2k), and sodium bis(fluorosulfonyl)imide (NaFSI) salt is investigated to facilitate the formation of amorphous, high σ i SPEs through end-group engineering and polymer ratio optimization. PEGMEMA enhances structural integrity via crosslinking with PEGDA through its methacrylate group, while its methyl end group aids ion conduction. A 2:1:7 ratio of PEGDA:PEGMEMA:PEG2k exhibits a σi of 1.16 x 10 -4 S cm -1 and oxidative stability up to 4.4 V at 60 °C. A solid-state cell incorporating this SPE, a Na 2/3 Ni 1/3 Mn 2/3 O 2 (NM12) cathode, and a sodium-metal anode demonstrates excellent cycling stability, retaining over 80 % of its initial capacity for 150 cycles at 60 °C. The findings highlight the potential of end-group engineering in improving the electrochemical performance of SPEs.

25 ENERGY STORAGE↗
NASA NTRS2007

Composite Electrolytes for Lithium Batteries: Ionic Liquids in APTES Crosslinked Polymers

Solvent free polymer electrolytes were made consisting of Li(+) and pyrrolidinium salts of trifluoromethanesulfonimide added to a series of hyperbranched poly(ethylene oxide)s (PEO). The polymers were connected by triazine linkages and crosslinked by a sol-gel process to provide mechanical strength. The connecting PEO groups were varied to help understand the effects of polymer structure on electrolyte conductivity in the presence of ionic liquids. Polymers were also made that contain poly(dimethylsiloxane) groups, which provide increased flexibility without interacting with lithium ions. When large amounts of ionic liquid are added, there is little dependence of conductivity on the polymer structure. However, when smaller amounts of ionic liquid are added, the inherent conductivity of the polymer becomes a factor. These electrolytes are more conductive than those made with high molecular weight PEO imbibed with ionic liquids at ambient temperatures, due to the amorphous nature of the polymer.

Tigelaar, Dean M.↗
DOE OSTI2018

Impact of cross-linking of polymers on transport of salt and water in polyelectrolyte membranes: A mesoscopic simulation study

Our recent atomistic simulation studies demonstrated that the transport properties of salt ions and water in non-crosslinked polymer electrolyte membrane exhibit an intriguing dependence on salt concentration that is opposite to that seen in electrolyte solutions. Here in this paper, we extend our study to probe the influence of the degree of cross-linking of the polymer on the transport properties of salt and water in polymer electrolyte membranes. Towards this objective, we use a coarse-grained model embedded within dissipative particle dynamics (DPD) mesoscale simulations, which allows us to access time scales necessary for studying crosslinked polymer systems. Our DPD simulations on non-crosslinked membranes reproduce results that are in qualitative agreement with our atomistic simulations. For the case of crosslinked membranes, our results demonstrate that the diffusion of salt ions and water is reduced significantly relative to crosslinked systems. However, the trends exhibited by the salt concentration dependence of diffusivities and the coordination of the cations with anions and with the polymer backbone remain qualitatively similar to those observed in non-crosslinked membranes.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Influences of Mg Ions and Al Ions on Deposition Behavior of Supersaturated Silicic Acid - 20261

Silicic acid can change into various species such as deposit, colloidal, and soluble form under certain conditions: for example, gradual pH changes around geological disposal repositories. In particular, silicic acid deposits narrow groundwater flow paths, thereby restricting the flow of groundwater. Such effects may contribute to a delay in radionuclide migration. Previous studies have reported that silicic acid supersaturated in sodium and calcium ions can narrow the flow paths. This study examined the effect of magnesium (Mg) and aluminum (Al) ions on the deposition of supersaturated silicic acid on the solid phase. The deposition behavior of supersaturated silicic acid on the solid phase was investigated in a batch system while changing the initial supersaturation concentration, the coexisting ion concentration, and the amount of added solid phase. In the presence of Mg ions, silicic acid precipitation increased with increasing Mg ion concentration due to the influence of the electrolyte, and crosslinking reactions. The coexistence of Al ions significantly suppressed silicic acid deposition due to the formation of a covering on the solid surface during Al ion hydrolysis under conditions of high Al concentration (1.4 mM). On the basis of these experimental results, the apparent deposition rate constant of silicic acid was estimated to be in the range from 10{sup -11} to 10{sup -10} m/s. The Damkoehler number (the dimensionless number expressed by the ratio of the characteristic time of mass transfer and the chemical reaction constant) was sufficient to cause the clogging of the host rock by deposition. This suggests that supersaturated silicic acid deposition, regardless of the presence of Mg ions (and Al ions), contributes to improving barrier performance against radionuclide migration in the host rock. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Design of a multi-functional gel polymer electrolyte with a 3D compact stacked polymer micro-sphere matrix for high-performance lithium metal batteries

We report lithium metal batteries (LMBs) are considered as promising high energy density batteries. However, they still suffer from poor cyclability due to the instability of solid electrolyte interphases (SEIs) and Li dendrite issues. Herein, a novel 3D densely packed multifunctional crosslinked gel polymer electrolyte (PHGPE) has been synthesized by in situ copolymerization of pentaerythritol tetraacrylate and 2-hydroxyethyl acrylate in a liquid electrolyte via a thermal initiation method. Due to intermolecular hydrogen bonding in the frameworks, the PHGPE exhibits a 3D compact-stacked and crosslinked micro-sphere structure, which benefits the construction of homogeneous Li + flux, enabling uniform Li plating/stripping and formation of robust SEIs onto the lithium electrode. Benefiting from the above advantages, symmetric Li cells in the PHGPE deliver excellent cyclabilities of 6000 h at a current density of 1 mA cm -2 (1 mA h cm -2 ) and 7700 h at 0.5 mA cm -2 (2 mA h cm -2 ). Moreover, the PHGPE has such a wide electrochemical window that it is compatible with both high-voltage LiNi 0.8 Co 0.1 Mn 0.1 O 2 and sulfur cathodes to realize long cycle life. Additionally, a LiFePO 4 based pouch size LMB also presents promising performance. Therefore, this study of the PHGPE has opened a new avenue for high-performance LMBs with excellent versatility and practicality.

25 ENERGY STORAGE↗
DOE OSTI2025

Modulating physicochemical interfaces enables li-rich oxides based ceramic solid-state li batteries under ambient conditions

Li-rich layered oxides exhibit promising potential applications in high-energy-density solid-state lithium metal batteries. Nevertheless, the strong oxidative oxygen species generate at high voltage, which poses great challenges to positive electrode-side interface stability. Herein, a robust in-situ polymerization gel polymer electrolyte with bifunctional additives is designed for interface modification. These additives, include lithium difluoro(oxalate) borate and LiPO 2 F 2 , regulate the Li + chemical environment in gel polymer electrolyte to enhance crosslink density without residual oligomer, which reduce gas generation and suppress contact loss, thus avoiding interfacial impedance divergence. Concurrently, the designed gel polymer electrolyte enables a wide electrochemical stability window (up to 4.7 V) and a high Li + transference number (0.82). Additionally, the additives induced F- and B-rich inorganic cathode-electrolyte interphase inhibits side reactions and oxygen/transition metal loss effectively, stabilizing the chemical interface. The as-constructed Li-rich layered oxides-based ceramic solid-state lithium metal batteries with gel polymer electrolyte interface modification exert a high discharge capacity of 276.5 mAh g -1 at 30 °C without external pressure, delivering a retention of 81.7% after 100 cycles at 25 mA g -1 during 2.0-4.7 V. This work provides a guideline for developing high-voltage solid-state lithium metal batteries via interfacial design.

Hu, Xinchao [Xiamen University (China)]↗
DOE OSTI2020

Reversible Crosslinked Polymer Binder for Recyclable Lithium Sulfur Batteries with High Performance

Owing to the negative impact of the extensive utilization of batteries on the environment, sustainability of the cells needs to be included in the systemic research of batteries. In this work, a dissolvable ionic crosslinked polymer (DICP) is exploited as a binder for lithium–sulfur batteries by crosslinking the polyacrylic acid and polyethyleneimine through carboxy-amino ionic interaction. This interaction is pH-controlled, and therefore, the crosslinked binder network can be readily dissociated under basic conditions, providing a facile strategy enabling valuable components recycled through a convenient washing method. The sulfur cathode prepared using the recycled carbon–sulfur composite can deliver comparable capacity as that of fresh electrode. In addition, evidence from cell performance and characterizations, such as in situ X-ray absorption spectroscopy, in situ UV–visible spectroscopy, X-ray photoelectron spectroscopy, and density functional theory calculation, confirms that DICP is a more effective binder than its commercial counterpart on suppressing polysulfide dissolution in the electrolyte. Exploiting reversible crosslinked polymer binder for recyclable Li–S batteries with ameliorated electrochemical performance, this study illuminates sustainable development for large-scale energy storage systems.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Crosslinked Poly(tetrahydrofuran) as a Loosely Coordinating Polymer Electrolyte

Abstract Solid polymer electrolytes (SPEs) promise to improve the safety and performance of lithium ion batteries (LIBs). However, the low ionic conductivity and transference number of conventional poly(ethylene oxide) (PEO)‐based SPEs preclude their widespread implementation. Herein, crosslinked poly(tetrahydrofuran) (xPTHF) is introduced as a promising polymer matrix for “beyond PEO” SPEs. The crosslinking procedure creates thermally stable, mechanically robust membranes for use in LIBs. Molecular dynamics and density functional theory (DFT) simulations accompanied by 7 Li NMR measurements show that the lower spatial concentration of oxygen atoms in the xPTHF backbone leads to loosened O–Li + coordination. This weakened interaction enhances ion transport; xPTHF has a high lithium transference number of 0.53 and higher lithium conductivity than a xPEO SPE of the same length at room temperature. It is demonstrated that organic additives further weaken the O–Li + interaction, enabling room temperature ionic conductivity of 1.2 × 10 −4 S cm −1 with 18 wt% N,N ‐dimethylformamide in xPTHF. In a solid‐state LIB application, neat xPTHF SPEs cycle with near theoretical capacity for 100 cycles at 70 °C, with rate capability up to 1 C. The plasticized xPTHF SPEs operate at room temperature while maintaining respectable rate capability and capacity. The novel PTHF system demonstrated here represents an exciting platform for future studies involving SPEs.

Mackanic, David G.↗
DOE OSTI2024

Development of Tailored Hydrocarbon-Based Pentablock Copolymer Membranes for Sodium-Polysulfide Flow Batteries

Long-duration energy storage (LDES) technologies are pivotal for the adoption of renewables like wind and solar. Non-aqueous redox flow batteries (NARFBs) with a sodium-polysulfide hybrid system feature high energy density independent of power density, yet face challenges with polysulfide shuttling. This study investigates a hydrocarbon-based penta-block copolymer membrane, Nexar, to mitigate crossover effects by balancing TFSI conversion and their crosslink density. The membranes are annealed to induce crosslinking for reducing electrolyte uptake and enhancing mechanical stability while demonstrating excellent ionic conductivity. The hydrocarbon-based membranes address environmental concerns associated with perfluoroalkyl substances and improve the performance and durability of NARFBs. In conclusion, our findings suggest that annealed Nexar membranes with tailored TFSI functionality offer a scalable, cost-effective solution for enhancing the efficiency of high-capacity energy storage systems, pivotal for grid integration of renewable sources.

25 ENERGY STORAGE↗
DOE OSTI2021

Designing polymer coatings for lithium metal protection

Abstract Protection of lithium metal has been one of the great challenges to realize a long-life, high-energy-density battery. Polymer coatings on lithium metal surface have been proven to be an effective protection method in terms of improved morphology, higher coulombic efficiency, and a longer cycle life. However, there is a variety of design principles of polymer coatings proposed by the research community, and the influence of polymer swelling in liquid electrolytes remains poorly understood. Herein we use crosslinking density and solvent–polymer interaction to quantitatively explain the mechanical property and the ion-transport property of polymer coatings when swollen in liquid electrolytes. Low crosslinking density is beneficial for reducing the rigidity and enhancing the viscosity of the polymer. Ion conductivity increases with the swelling ratio, and activation energy of lithium-ion transport increases in a polar polymer with strong ion–polymer coupling. We propose that polymer coatings must be combined with the emerging electrolytes with unconventional solvent compositions to realize a practical high-performance lithium metal battery. This study can provide design guidelines for polymer coatings through the optimized interactions with upcoming high-performance electrolytes.

Materials Science↗