Search NASA⌕ Search

SEARCH · Search NASA

Results for “curing processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

ASRM test report: Autoclave cure process development

ASRM insulated segments will be autoclave cured following insulation pre-form installation and strip wind operations. Following competitive bidding, Aerojet ASRM Division (AAD) Purchase Order 100142 was awarded to American Fuel Cell and Coated Fabrics Company, Inc. (Amfuel), Magnolia, AR, for subcontracted insulation autoclave cure process development. Autoclave cure process development test requirements were included in Task 3 of TM05514, Manufacturing Process Development Specification for Integrated Insulation Characterization and Stripwind Process Development. The test objective was to establish autoclave cure process parameters for ASRM insulated segments. Six tasks were completed to: (1) evaluate cure parameters that control acceptable vulcanization of ASRM Kevlar-filled EPDM insulation material; (2) identify first and second order impact parameters on the autoclave cure process; and (3) evaluate insulation material flow-out characteristics to support pre-form configuration design.

Nachbar, D. L.↗
NASA NTRS2016

Composite Cure Process Modeling and Simulations using COMPRO(Registered Trademark) and Validation of Residual Strains using Fiber Optics Sensors

Composite cure process induced residual strains and warping deformations in composite components present significant challenges in the manufacturing of advanced composite structure. As a part of the Manufacturing Process and Simulation initiative of the NASA Advanced Composite Project (ACP), research is being conducted on the composite cure process by developing an understanding of the fundamental mechanisms by which the process induced factors influence the residual responses. In this regard, analytical studies have been conducted on the cure process modeling of composite structural parts with varied physical, thermal, and resin flow process characteristics. The cure process simulation results were analyzed to interpret the cure response predictions based on the underlying physics incorporated into the modeling tool. In the cure-kinetic analysis, the model predictions on the degree of cure, resin viscosity and modulus were interpreted with reference to the temperature distribution in the composite panel part and tool setup during autoclave or hot-press curing cycles. In the fiber-bed compaction simulation, the pore pressure and resin flow velocity in the porous media models, and the compaction strain responses under applied pressure were studied to interpret the fiber volume fraction distribution predictions. In the structural simulation, the effect of temperature on the resin and ply modulus, and thermal coefficient changes during curing on predicted mechanical strains and chemical cure shrinkage strains were studied to understand the residual strains and stress response predictions. In addition to computational analysis, experimental studies were conducted to measure strains during the curing of laminated panels by means of optical fiber Bragg grating sensors (FBGs) embedded in the resin impregnated panels. The residual strain measurements from laboratory tests were then compared with the analytical model predictions. The paper describes the cure process procedures and residual strain predications, and discusses pertinent experimental results from the validation studies.

Sreekantamurthy, Thammaiah↗
NASA NTRS1986

Dynamic dielectric analysis - A nondestructive cure process monitoring method

The cure processes of TGDDM-based epoxy thermosets and polysulfone thermoplastic resins were monitored by means of computer-controlled dynamic dielectric measurements made at frequencies 5 Hz to 5 million Hz. The values of capacitance and conductance were recorded, and the data were used to calculate the complex permittivity, an intensive property which is characteristic of the material's state of cure and independent of the amount of material measured. The frequency dependence of the complex permittivity value was used to determine the conductivity and mean relaxation time. The conductivity which is also an intensive variable and is independent of sample size, was correlated with the viscosity in both the epoxy and polysulfone systems.

Kranbuehl, D. E.↗
NASA NTRS1989

Method of controlling a resin curing process

An analytical technique for controlling the curing process of fiber-reinforced composite materials that are formed using thermosetting resins. The technique is the percent gel method and involves development of a time-to-gel equation as s function of temperature. From this equation a rate-of-gel equation is then determined, and a percent gel is calculated which is the product of the rate-of-gel times time. Percent gel accounting is used to control the proper pressure application point in an autoclave cure process to achieve desired properties in a production composite part.

Charles Neal Webster↗
DOE OSTI2021

Curing process and pore structure of metakaolin-based geopolymers: Liquid-state 1H NMR investigation

Geopolymers are emerging construction materials with lower carbon dioxide emissions compared to the conventional cementitious materials. The knowledge of the curing process and the related pore structures are important for optimizing the properties of these materials for different applications. The curing process and final pore structure are sensitive to the amount of used water, however the specifics are unclear. The curing process and pore structures of metakaolin-based geopolymers with a narrow water-to-solid (w/s) ratio (0.59–0.66) were monitored by nuclear magnetic resonance (NMR) relaxometry and cryoporometry. The 14-day curing process was investigated by monitoring the change of T{sub 2} and T{sub 1} relaxation times and water signal intensity. After the curing, the pore structures were characterized by 2D T{sub 1}-T{sub 2} correlation and T{sub 2}-T{sub 2} exchange measurements of absorbed water. The pore size distributions (PSDs) were measured with NMR cryoporometry and compared to nitrogen physisorption and mercury intrusion porosimetry (MIP) results. We found that the relaxation times decreased as the pore structure of the geopolymers matured during the curing while the dissolution and the condensation periods of the curing were distinguished by the changes in signal amplitude reflecting the proton density. After the curing, three distinct pore sizes and connectivity between pores were identified from T{sub 1}-T{sub 2} and T{sub 2}-T{sub 2} spectra. Their PSDs were measured, and they were found to correspond to two different pore sizes originating from the arrangement of clusters and defective pores. In the narrow w/s ratio (0.59–0.66), the curing times were the same for all samples when cured at 24 °C while the pore sizes were observed to increase as a function of the w/s ratio.

36 MATERIALS SCIENCE↗
NASA NTRS2016

Development of a Fully Automated Guided Wave System for In-Process Cure Monitoring of CFRP Composite Laminates

A guided wave-based in-process cure monitoring technique for carbon fiber reinforced polymer (CFRP) composites was investigated at NASA Langley Research Center. A key cure transition point (vitrification) was identified and the degree of cure was monitored using metrics such as amplitude and time of arrival (TOA) of guided waves. Using an automated system preliminarily developed in this work, high-temperature piezoelectric transducers were utilized to interrogate a twenty-four ply unidirectional composite panel fabricated from Hexcel (Registered Trademark) IM7/8552 prepreg during cure. It was shown that the amplitude of the guided wave increased sharply around vitrification and the TOA curve possessed an inverse relationship with degree of cure. The work is a first step in demonstrating the feasibility of transitioning the technique to perform in-process cure monitoring in an autoclave, defect detection during cure, and ultimately a closed-loop process control to maximize composite part quality and consistency.

Hudson, Tyler B.↗
NASA NTRS1985

Modeling the curing process of thick-section autoclave cured composites

Temperature gradients are significant during cure of large area, thick-section composites. Such temperature gradients result in nonuniformly cured parts with high void contents, poor ply compaction, and variations in the fiber/resin distribution. A model was developed to determine the temperature distribution in thick-section autoclave cured composites. Using the model, long with temperature measurements obtained from the thick-section composites, the effects of various processing parameters on the thermal response of the composites were examined. A one-dimensional heat transfer model was constructed for the composite-tool assembly. The governing differential equations and associated boundary conditions describing one-dimensional unsteady heat-conduction in the composite, tool plate, and pressure plate are given. Solution of the thermal model was obtained using an implicit finite difference technique.

Loos, A. C.↗
NASA NTRS1986

Modeling the curing process of thermosetting resin matrix composites

A model is presented for simulating the curing process of a thermosetting resin matrix composite. The model relates the cure temperature, the cure pressure, and the properties of the prepreg to the thermal, chemical, and rheological processes occurring in the composite during cure. The results calculated with the computer code developed on the basis of the model were compared with the experimental data obtained from autoclave-curved composite laminates. Good agreement between the two sets of results was obtained.

Loos, A. C.↗
DOE OSTI2024

Modeling of Sagging for 3D Printed Layers During the Curing Process

Here, a printed layer of silica-enforced poly(dimethylsiloxane)-co-(diphenylsiloxane) is modeled as a two-phase system consisting of air and polymer with an interface set up during the printing process. The structural geometry changes mostly due to the action of surface tension, while all material properties are strongly temperature dependent. Polymer flow is described using equations of the extended Herschel–Bulkley model, with parameters strongly dependent on temperature and degree of curing. Parameters of the model are determined using flow sweep measurements and separate experiments with vertical structure sagging at different temperatures. The curing process is modeled using dependencies between the curing rate, degree of curing, and temperature obtained in studies by differential scanning calorimetry. The developed model is used for simulations of printed structure deformations with different initial and boundary conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigating the Curing Process of Epoxy Thermosets by Near-Infrared (nIR) Spectroscopy

Near-Infrared (nIR) Spectroscopy is a type of absorption spectroscopy that may be used to study the curing process of thermosetting epoxy-based resins like Eccostock FFP. This is accomplished by monitoring the absorption bands of the epoxy oxirane ring, which decrease in intensity with increasing degree of cure. Relative to epoxy absorption bands in the mid-IR region, those in the nIR range exhibit less overlap, allowing for a more accurate analysis of cure kinetics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1982

Detection of trace quantities of dimethylacetamide during the curing process of a polyimide film

An experimental study of positive ion clustering of dimethylacetamide (DMAC) with water molecules using high pressure mass spectrometry techniques is reported. The possibilities of using these techniques to determine the concentration levels of DMAC evolved from a polyimide film during the curing process, are examined. The test sample of gas contained DMAC of the order of a few micrograms, water, nitrogen, oxygen, and other compounds that might evolve during the curing cycle of a polyimide film. It is found that PPM concentrations such as DMAC lost from polyimide during curing stages can be detected with this technique. Improvement of the detection of lower concentrations (50 picograms) can be made by using electron multipliers with a gain in the 10 to the 8th power range and pulse counting techniques.

Smith, A. C.↗
NASA NTRS1983

Mechanism and kinetics of the curing process in a resin system

The present investigation is concerned with the development of a cure reactivity model for a resin system consisting of tetraglycidyl diaminodiphenyl methane (TGDDM) and diaminodiphenyl sulfone (DDS), taking into account the temperature range from 153 to 177 C. Differential scanning calorimetry and FT-IR spectroscopy have been used to investigate the cure kinetics of the resin with the objective to obtain a correlation between the total conversion and the rates of formation and disappearance of specific functionalities. It was found that the overall process can be satisfactorily described in terms of two first order processes.

Moacanin, J.↗
DOE OSTI2020

Effects of Photonic Curing Processing Conditions on MAPbI 3 Film Properties and Solar Cell Performance

Thermal annealing is the most used postdeposition materials processing method in laboratory research, but due to its slow speed and high energy cost, it is not compatible with the upscaling and commercialization of perovskite solar cell (PSC) manufacturing. Here, we adapt photonic curing (PC), which uses millisecond light pulses to deliver energy to the sample, to replace thermal annealing for crystallization of methylammonium lead iodide (MAPbI 3 ) films and rapid fabrication of PSCs. We study how PC conditions affect the outcome of MAPbI 3 conversion from the precursor to the crystalline perovskite phase by evaluating the films’ optical, crystalline, and morphological properties, as well as PSC performance. The results are understood using simulated film temperature profiles. We show that MAPbI 3 is readily converted under a wide range of PC conditions. While previous reports all used short pulses (<3 ms), we find that longer pulses produce more dense films and higher-performing PSCs. We achieve a champion power conversion efficiency in a PC-processed MAPbI 3 PSC of 11.26% under forward scan and 10.34% under reverse scan, with the processing time for the MAPbI 3 layer reduced by 30,000-fold, from 10 min to 20 ms. Using a 6 in. lamp, spatial uniformity tests show a cross-web efficiency variation of 5%. Our results indicate that using longer pulse lengths, >10 ms, is the best PC strategy for perovskite conversion, and PC is a promising annealing method for large-area, high-throughput PSC manufacturing.

14 SOLAR ENERGY↗
NASA NTRS1988

Addition polymers from 1,4,5,8-tetrahydro-1,4;5,8-diepoxyanthracene and Bis-dienes. 2: Evidence for thermal dehydration occurring in the cure process

Diels-Alder cycloaddition copolymers from 1,4,5,8-tetrahydro-1,4;5,8-diepoxyanthracene and anthracene end-capped polyimide oligomers appear, by thermogravimetric analysis (TGA), to undergo dehydration at elevated temperatures. This would produce thermally stable pentiptycene units along the polymer backbone, and render the polymers incapable of unzipping through a retro-Diels-Alder pathway. High resolution solid 13C nuclear magnetic resonance (NMR) of one formulation of the polymer system before and after heating at elevated temperatures, shows this to indeed be the case. NMR spectra of solid samples of the polymer before and after heating correlated well with those of the parent pentiptycene model compound before and after acid-catalyzed dehydration. Isothermal gravimetric analyses and viscosities of the polymer before and after heat treatment support dehydration as a mechanism for the cure reaction.

Meador, Mary Ann B.↗
DOE OSTI2025

Advanced electrode processing for lithium-ion battery manufacturing

Lithium-ion batteries (LIBs) need to be manufactured at speed and scale for their use in electric vehicles and devices. However, LIB electrode manufacturing via conventional wet slurry processing is energy-intensive and costly, challenging the goal to achieve sustainable, affordable and facile manufacturing of high-performance LIBs. Here, in this Review, we discuss advanced electrode processing routes (dry processing, radiation curing processing, advanced wet processing and 3D-printing processing) that could reduce energy usage and material waste. Maxwell-type dry processing is a scalable alternative to conventional processing and has relatively low manufacturing cost and energy consumption. Radiation curing processing could enable high-throughput manufacturing, but binder selection is limited to certain radiation curable chemistries. 3D-printing processing can produce electrodes with diverse architectures and improved rate performance, but scalability is yet to be demonstrated. 3D-printing processing is good for special applications where throughput and cost can be compromised for performance.

25 ENERGY STORAGE↗