Search NASA⌕ Search

SEARCH · Search NASA

Results for “cutters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Reusable Hot-Wire Cable Cutter

During the early development stage of balloon deployment systems for missions, nichrome wire cable cutters were often used in place of pyro-actuated cutters. Typically, a nichrome wire is wrapped around a bundle of polymer cables with a low melting point and connected to a relay-actuated electric circuit. The heat from the nichrome reduces the strength of the cable bundle, which quickly breaks under a mechanical load and can thus be used as a release mechanism for a deployment system. However, the use of hand-made heated nichrome wire for cutters is not very reliable. Often, the wrapped nichrome wire does not cut through the cable because it either pulls away from its power source or does not stay in contact with the cable being cut. Because nichrome is not readily soldered to copper wire, unreliable mechanical crimps are often made to connect the nichrome to an electric circuit. A self-contained device that is reusable and reliable was developed to sever cables for device release or deployment. The nichrome wire in this new device is housed within an enclosure to prevent it from being damaged by handling. The electric power leads are internally connected within the unit to the nichrome wire using a screw terminal connection. A bayonet plug, a quick and secure method of connecting the cutter to the power source, is used to connect the cutter to the power leads similar to those used in pyro-cutter devices. A small ceramic tube [0.25-in. wide 0.5-in. long (.6.4-mm wide 13-mm long)] houses a spiraled nichrome wire that is heated when a cable release action is required. The wire is formed into a spiral coil by wrapping it around a mandrel. It is then laid inside the ceramic tube so that it fits closely to the inner surface of the tube. The ceramic tube provides some thermal and electrical insulation so that most of the heat generated by the wire is directed toward the cable bundle in the center of the spiral. The ceramic tube is cemented into an aluminum block, which holds it in position. The leads of the nichrome wire are attached to screw terminals that connect them to power leads. A bayonet plug mounted at the bottom of the rectangular block connects the power leads to a relay circuit. A thin aluminum shell encloses the entire structure, leaving access points to attach to the bayonet plug and to feed a cable into the cylinder. The access holes for the deployment cable are a smaller diameter than the nichrome coil to prevent the cable from coming in direct contact with the nichrome when loaded. It uses the same general method of severing a cable with a heated wire as was used previously, but implements it in such a way that it is more reliable and less prone to failure. It creates a mechanism to create repeatability that was nonexistent in the previous method.

Pauken, Michael T.↗

Bolt cutter functional evaluation

The Aerospace Corporation has been implementing finite difference and finite element codes for the analysis of a variety of explosive ordnance devices. Both MESA-2D and DYNA3D have been used to evaluate the role of several design parameters on the performance of a satellite separation system bolt cutter. Due to a lack of high strain rate response data for the materials involved, the properties for the bolt cutter and the bolt were selected to achieve agreement between computer simulation and observed characteristics of the recovered test hardware. The calculations provided insight into design parameters such as the cutter blade kinetic energy, the preload on the bolt, the relative position of the anvil, and the anvil shape. Modeling of the cutting process clarifies metallographic observation of both cut and uncut bolts obtained from several tests. Understanding the physical processes involved in bolt cutter operation may suggest certain design modifications that could improve performance margin without increasing environmental shock response levels.

S. Goldstein↗

Tubing cutter for tight spaces

Cutter requires few short swings of handle to rotate its cutting edge full 360 around tube. It will cut tubing installed in confined space that prevents free movement of conventional cutter. Cutter is snapped onto tube and held in place by spring-loaded clamp. Screw ratchet advances cutting wheel.

Girala, A. S.↗

Tubing Cutter is Activated Hydraulically

Hydraulically-actuated tubing cutter severs tubing when operator squeezes handle grip. "Gooseneck" extension enables cutter to be used in areas where accessiblity is limited. Cutter has potential as flight-line tool and is useful in automobile and fire rescue work.

Mcsmith, D. G.↗

Hole cutter

An adjustable hole cutter is described for use in forming circular openings in workpieces. The hole cutter is characterized by a mount of a substantially planar configuration, positionable into a plane paralleling the working plane of a selected workpiece. It also contains a shaft for imparting rotary motion to the mount about an axis of rotation normally related to the working plane, a plurality of stabilizing struts for resiliently supporting the mount in parallelism with the working plane as rotary motion is imparted thereto, a drill bit for drilling a pilot hole concentric with the axis of rotation, and an elongated cutting tool adjustably seated within a radially extended slot.

Thornton, G. E.↗

Precision filament cutter

Automated cutter precisely chops filaments of glass, graphite, plastic, and other materials into fibers for use in composites and other applications. Cutter uses movable blade that is pushed and pulled across fixed blade. Because mass of movable blade is small and stroke is short, operation is fast, and wear and energy consumption are low. Blade cuts on both forward and return movements. Operator selects fiber length and chopping rate. After each cut, blast of air blows filament away so it can be collected.

Mchatton, A. D.↗

Determination of settings of a tilted head-cutter for generation of hypoid and spiral bevel gears

Kinematics of Gleason mechanisms of hypoid and spiral bevel cutting machines are considered. These mechanisms are designated to install the position and tilt of the head cutter. The tilt of the head cutter with standard blades provides the required pressure angle. The authors have developed the matrix presentation of kinematics of these meachanisms and basic equations for the required settings. An example is presented based on the developed computation procedure.

Litvin, F. L.↗

Jam-Resistant Cutters For Emergency Separation

Pyrotechnic emergency-separation system includes shaped explosive charges that sever pair of hinges. System ensures reliable opening of escape hatch. Two pairs of cutters provided for each hinge so if one pair of cutters fails, other completes job. Pressure of explosions vented to prevent charge holders from fragmenting and forming sharp edges around open hatch. Exit slide deployed without tearing. Before detonation L-shaped retainers bear on hinge. After denonation, retainers fold outward to facilitate egress of severed hinges.

Ordonez, Arturo C.↗

Orion Parachute Riser Cutter Development

This paper presents the tests and analytical approach used on the development of a steel riser cutter for the CEV Parachute Assembly System (CPAS) used on the Orion crew module. Figure 1 shows the riser cutter and the steel riser bundle which consists of six individual cables. Due to the highly compressed schedule, initial unavailability of the riser material and the Orion Forward Bay mechanical constraints, JSC primarily relied on a combination of internal ballistics analysis and LS-DYNA simulation for this project. Various one dimensional internal ballistics codes that use standard equation of state and conservation of energy have commonly used in the development of CAD devices for initial first order estimates and as an enhancement to the test program. While these codes are very accurate for propellant performance prediction, they usually lack a fully defined kinematic model for dynamic predictions. A simple piston device can easily and accurately be modeled using an equation of motion. However, the accuracy of analytical models is greatly reduced on more complicated devices with complex external loads, nonlinear trajectories or unique unlocking features. A 3D finite element model of CAD device with all critical features included can vastly improve the analytical ballistic predictions when it is used as a supplement to the ballistic code. During this project, LS-DYNA structural 3D model was used to predict the riser resisting load that was needed for the ballistic code. A Lagrangian model with eroding elements shown in Figure 2 was used for the blade, steel riser and the anvil. The riser material failure strain was fine tuned by matching the dent depth on the anvil with the actual test data. LS-DYNA model was also utilized to optimize the blade tip design for the most efficient cut. In parallel, the propellant type and the amount were determined by using CADPROG internal ballistics code. Initial test results showed a good match with LS-DYNA and CADPROG simulations. Final paper will present a detailed roadmap from initial ballistic modeling and LS-DYNA simulation to the performance testing. Blade shape optimization study will also be presented.

Oguz, Sirri↗

Sleeve and cutter simplify disconnecting welded joint in tubing

To test equipment, welded tubing joints may have to be disconnected and rewelded. To eliminate rewelding, a nonstandard welding sleeve permits the tubing to be welded and then disconnected by a specially designed sleeve cutter. Use of this tool assures that only the sleeve is cut.

Perkins, G. S.↗

Cutter and stripper reduces coaxial cable connection time

Consisting of three pivoted members, this hand cutter and stripper positions to cut shielding and insulation at the right distance and depth. Coaxial cable is prepared quickly and accurately for connector attachment.

Thompson, F. E.↗

Phenolic cutter for machining foam insulation

Pre-pregged fiber glass is an efficient abrasive for machining polystyrene and polyurethane foams. It bonds easily to any cutter base made of aluminum, steel, or phenolic, is inexpensive, and is readily available.

Blair, T. A.↗

Line cutter Patent

Piston in bore cutter for severing parachute control lines and sealing cable hole to prevent water leakage into load

Chandler, J. A.↗

Tubing cutter

Replacement of opposing smooth rollers with appropriately grooved rollers in manual tubing cutter allows smooth severance of tubing of different diameters and eliminates raised lip around cut end.

Giandomenico, A.↗

Sharpening ball-nose mill cutters

Economical attachment allows faster, more precise grinding. Vibrationless and rigid relation between grinding wheel and cutter allows for extremely high finish and accurate grinding. Leveling device levels flutes with respect to toolholder rotation that generates ball-nose radius. Constant relief around entire profile of cutting edge produces longer tool life.

Burch, C. F.↗

Cutter for Woven Materials

Simple tool makes accurate square cuts through strips of woven or felted materials, such as high temperature aramid fabric. Pressing handle on Guillotine Cutter forces razor blade through strip of material in slot, cutting strip off squarely.

Hammons, J. M.↗

Open ended tubing cutters

A self clamping cutting tool which includes a handle attached to a C-shaped housing is described. Rotatably mounted within the housing is a C-shaped tool body carrying a set of clamping rolls, two support rolls, and an edged cutting roll (64). The support rolls are disposed to one side of the axis of a pipe and the cutting roll is disposed to the other side of a pipe axis so that these rolls contact a pipe at three circumferential points. Cutter advancing apparatus advance the cutting roll toward the support rollers. The support rolls and cutting roll are rotatable independently of the C-shaped housing. A one way ratchet mechanism disposed between the C-shaped housing and the C-shaped tool body permits operation by movement in one rotational direction about the pipe axis.

Girala, A. S.↗

Effects of Gear-Cutter Geometry on Performance

Bending stress reduced by improving tooth-fillet design. Using optimized gear-cutter design technology, gear designer reduces bending stresses by up to 20 percent. Reduction in bending stress is result of improved geometry of tooth fillet, which, in turn, results in significant improvement in horsepower-per-pound ratio. Gears run quieter and smoother than spur-gear system.

Folenta, D.↗